summaryrefslogtreecommitdiff
path: root/drivers/pci/setup-res.c
AgeCommit message (Collapse)Author
2005-09-08[PATCH] Make sparc64 use setup-res.cDavid S. Miller
There were three changes necessary in order to allow sparc64 to use setup-res.c: 1) Sparc64 roots the PCI I/O and MEM address space using parent resources contained in the PCI controller structure. I'm actually surprised no other platforms do this, especially ones like Alpha and PPC{,64}. These resources get linked into the iomem/ioport tree when PCI controllers are probed. So the hierarchy looks like this: iomem --| PCI controller 1 MEM space --| device 1 device 2 etc. PCI controller 2 MEM space --| ... ioport --| PCI controller 1 IO space --| ... PCI controller 2 IO space --| ... You get the idea. The drivers/pci/setup-res.c code allocates using plain iomem_space and ioport_space as the root, so that wouldn't work with the above setup. So I added a pcibios_select_root() that is used to handle this. It uses the PCI controller struct's io_space and mem_space on sparc64, and io{port,mem}_resource on every other platform to keep current behavior. 2) quirk_io_region() is buggy. It takes in raw BUS view addresses and tries to use them as a PCI resource. pci_claim_resource() expects the resource to be fully formed when it gets called. The sparc64 implementation would do the translation but that's absolutely wrong, because if the same resource gets released then re-claimed we'll adjust things twice. So I fixed up quirk_io_region() to do the proper pcibios_bus_to_resource() conversion before passing it on to pci_claim_resource(). 3) I was mistakedly __init'ing the function methods the PCI controller drivers provide on sparc64 to implement some parts of these routines. This was, of course, easy to fix. So we end up with the following, and that nasty SPARC64 makefile ifdef in drivers/pci/Makefile is finally zapped. Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-09-08[PATCH] PCI: restore BAR values after D3hot->D0 for devices that need itJohn W. Linville
Some PCI devices (e.g. 3c905B, 3c556B) lose all configuration (including BARs) when transitioning from D3hot->D0. This leaves such a device in an inaccessible state. The patch below causes the BARs to be restored when enabling such a device, so that its driver will be able to access it. The patch also adds pci_restore_bars as a new global symbol, and adds a correpsonding EXPORT_SYMBOL_GPL for that. Some firmware (e.g. Thinkpad T21) leaves devices in D3hot after a (re)boot. Most drivers call pci_enable_device very early, so devices left in D3hot that lose configuration during the D3hot->D0 transition will be inaccessible to their drivers. Drivers could be modified to account for this, but it would be difficult to know which drivers need modification. This is especially true since often many devices are covered by the same driver. It likely would be necessary to replicate code across dozens of drivers. The patch below should trigger only when transitioning from D3hot->D0 (or at boot), and only for devices that have the "no soft reset" bit cleared in the PM control register. I believe it is safe to include this patch as part of the PCI infrastructure. The cleanest implementation of pci_restore_bars was to call pci_update_resource. Unfortunately, that does not currently exist for the sparc64 architecture. The patch below includes a null implemenation of pci_update_resource for sparc64. Some have expressed interest in making general use of the the pci_restore_bars function, so that has been exported to GPL licensed modules. Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-08-26Ignore disabled ROM resources at setupLinus Torvalds
Writing even a disabled value seems to mess up some matrox graphics cards. It may be a card-related issue, but we may also be writing reserved low bits in the result. This was a fall-out of switching x86 over to the generic PCI resource allocation code, and needs more debugging. In particular, the old x86 code defaulted to not doing any resource allocations at all for ROM resources. In the meantime, this has been reported to make X happier by Helge Hafting <helgehaf@aitel.hist.no>. Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-08-09Revert "[PATCH] PCI: restore BAR values..."Linus Torvalds
Revert commit fec59a711eef002d4ef9eb8de09dd0a26986eb77, which is breaking sparc64 that doesn't have a working pci_update_resource. We'll re-do this after 2.6.13 when we'll do it all properly.
2005-08-07[PATCH] Fix restore of 64-bit PCI BAR'sIvan Kokshaysky
For 64-bit BAR[i] only pci_dev->resource[i] is valid, ->resource[i+1] slot is unused and contains zeroes in all fields. So when we update a PCI BAR, all we need is just to check that we're going to update a _valid_ resource. Also make sure to write high bits - use "x >> 16 >> 16" (rather than the simpler ">> 32") to avoid warnings on 32-bit architectures where we're not going to have any high bits. Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-08-05[PATCH] PCI: restore BAR values after D3hot->D0 for devices that need itJohn W. Linville
Some PCI devices (e.g. 3c905B, 3c556B) lose all configuration (including BARs) when transitioning from D3hot->D0. This leaves such a device in an inaccessible state. The patch below causes the BARs to be restored when enabling such a device, so that its driver will be able to access it. The patch also adds pci_restore_bars as a new global symbol, and adds a correpsonding EXPORT_SYMBOL_GPL for that. Some firmware (e.g. Thinkpad T21) leaves devices in D3hot after a (re)boot. Most drivers call pci_enable_device very early, so devices left in D3hot that lose configuration during the D3hot->D0 transition will be inaccessible to their drivers. Drivers could be modified to account for this, but it would be difficult to know which drivers need modification. This is especially true since often many devices are covered by the same driver. It likely would be necessary to replicate code across dozens of drivers. The patch below should trigger only when transitioning from D3hot->D0 (or at boot), and only for devices that have the "no soft reset" bit cleared in the PM control register. I believe it is safe to include this patch as part of the PCI infrastructure. The cleanest implementation of pci_restore_bars was to call pci_update_resource. Unfortunately, that does not currently exist for the sparc64 architecture. The patch below includes a null implemenation of pci_update_resource for sparc64. Some have expressed interest in making general use of the the pci_restore_bars function, so that has been exported to GPL licensed modules. Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-04-16Linux-2.6.12-rc2Linus Torvalds
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!