| Age | Commit message (Collapse) | Author |
|---|
|
Pull ARM SoC device tree conversions from Arnd Bergmann:
"These are device tree conversions for a number of platforms, with the
intention of turning code from board files into device tree
descriptions. Notable changes are:
- davinci bindings for pinctrl, MTD, RTC, watchdog and i2c
- nomadik bindings for all devices, removing the board files
- bcm2835 bindings for mmc and i2c
- tegra bindings for hdmi, keyboard, audio, as well as some updates
- at91 bindings for hardware ecc and for devices on RM9200
- mxs bindings for cfa100xx
- sunxi support for Miniand Hackberry board"
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (72 commits)
Revert "sunxi: a10-cubieboard: Add user LEDs to the device tree"
Revert "sunxi: a13-olinuxino: Add user LED to the device tree"
clk: tegra: initialise parent of uart clocks
ARM: tegra: remove clock-frequency properties from serial nodes
clk: tegra: fix driver to match DT binding
clk: tegra: local arrays should be static
clk: tegra: Add missing spinlock for hclk and pclk
clk: tegra: Implement locking for super clock
clk: tegra: fix wrong clock index between se to sata_cold
sunxi: a13-olinuxino: Add user LED to the device tree
ARM: davinci: da850 DT: add support for machine reboot
ARM: davinci: da850: add wdt DT node
ARM: davinci: da850: add DT node for I2C0
ARM: at91: at91sam9n12: add DT parameters to enable PMECC
ARM: at91: at91sam9x5: add DT parameters to enable PMECC
ARM: at91: add EMAC bindings to RM9200 DT
ARM: at91: add SSC bindings to RM9200 DT
ARM: at91: add MMC bindings to RM9200 DT
ARM: at91: Animeo IP: enable watchdog support
ARM: nomadik: fix OF compilation regression
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull sh-mobile pinctrl conversion from Arnd Bergmann:
"This is another cleanup series, containing the move of the Renesas
SH-Mobile pin controller code from arch/arm/mach-shmobile over to the
generic pinctrl subsystem, changing it over to the common interfaces
in the process.
Based on agreement between Olof, Paul Mundt, Linus Walleij and Simon,
we're merging this large branch of pinctrl conversion through arm-soc,
even though it contains the corresponding conversions for arch/sh.
Main reason for this is tight dependencies (that will now mostly be
broken) between the arch/sh and mach-shmobile implementations.
There will be more of this in 3.10 to do device-tree bindings, but
this is the initial conversion."
* tag 'sh-pinmux' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (81 commits)
sh-pfc: sh_pfc_probe() sizeof() fix
sh-pfc: Move sh_pfc.h from include/linux/ to driver directory
sh-pfc: Remove pinmux_info definition
sh: Remove unused sh_pfc_register_info() function
sh: shx3: pinmux: Use driver-provided pinmux info
sh: sh7786: pinmux: Use driver-provided pinmux info
sh: sh7785: pinmux: Use driver-provided pinmux info
sh: sh7757: pinmux: Use driver-provided pinmux info
sh: sh7734: pinmux: Use driver-provided pinmux info
sh: sh7724: pinmux: Use driver-provided pinmux info
sh: sh7723: pinmux: Use driver-provided pinmux info
sh: sh7722: pinmux: Use driver-provided pinmux info
sh: sh7720: pinmux: Use driver-provided pinmux info
sh: sh7269: pinmux: Use driver-provided pinmux info
sh: sh7264: pinmux: Use driver-provided pinmux info
sh: sh7203: pinmux: Use driver-provided pinmux info
ARM: shmobile: sh73a0: Use driver-provided pinmux info
ARM: shmobile: sh7372: Use driver-provided pinmux info
ARM: shmobile: r8a7779: Use driver-provided pinmux info
ARM: shmobile: r8a7740: Use driver-provided pinmux info
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull non-critical ARM SoC bug fixes from Arnd Bergmann:
"Bug fixes that did not make it into v3.8, mostly because they were not
considered important enough, and in some cases because bugs only show
up in combination with other patches destined for 3.9. This includes
a few larger patches for GPIO on the Marvell PXA platform and a lot of
Samsung specific bug fixes, as well as a series from Arnd to fix older
build warnings."
* tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
ARM: SPEAr13xx: Enable CONFIG_ARCH_HAS_CPUFREQ
ARM: imx: MACH_MX31ADS_WM1133_EV1 needs REGULATOR_WM8350
scripts/sortextable: silence script output
ARM: s3c: i2c: add platform_device forward declaration
ARM: mvebu: allow selecting mvebu without Armada XP
ARM: pick Versatile by default for !MMU
ARM: integrator: fix build with INTEGRATOR_AP off
ARM: integrator/versatile: fix NOMMU warnings
ARM: sa1100: don't warn about mach/ide.h
ARM: shmobile: fix defconfig warning on CONFIG_USB
ARM: w90x900: fix legacy assembly syntax
ARM: samsung: fix assembly syntax for new gas
ARM: disable virt_to_bus/virt_to_bus almost everywhere
ARM: dts: Correct pin configuration of SD 4 for exynos4x12-pinctrl
ARM: SAMSUNG: Silence empty switch warning in fimc-core.h
ARM: SAMSUNG: Silence empty switch warning in sdhci.h
ARM: msm: proc_comm_boot_wait should not be __init
arm: vt8500: Update MAINTAINERS entry for arch-vt8500
ARM: integrator: ensure ap_syscon_base is initialised when !CONFIG_MMU
ARM: S5PV210: Fix early uart output in fifo mode
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl changes from Linus Walleij:
"These are the main pinctrl changes for the v3.9 merge window. The
most interesting change by far is how the device core grabs pinctrl
default handles avoiding the need to stick boilerplate into driver
consumers.
- Grabbing of default pinctrl handles from the device core. These
are the hunks hitting drivers/base. All is ACKed by Greg, after a
long discussion about different alternatives.
- Some stuff also touches the MFD and ARM SoC trees, this has been
coordinated and ACKed.
- New drivers for:
- The Tegra 114 sub-SoC
- Allwinner sunxi
- New ABx500 driver and sub-SoC drivers for AB8500, AB8505, AB9540
and AB8540.
- Make it possible for hogged pins to enter a sleep mode, and make it
possible for drivers to control that mode.
- Various clean-up, extensions and device tree support to various pin
controllers."
* tag 'pinctrl-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (68 commits)
pinctrl: tegra: add clfvs function to Tegra114 support
pinctrl: generic: rename input schmitt disable
pinctrl/pinconfig: add debug interface
pinctrl: samsung: remove duplicated line
ARM: ux500: use real AB8500 IRQ numbers instead of virtual ones
ARM: ux500: remove irq_base property from platform_data
pinctrl/abx500: use direct IRQ defines
pinctrl/abx500: replace IRQ offsets with table read-in values
pinctrl/abx500: move IRQ handling to ab8500-core
pinctrl: exynos5440: remove erroneous __init
pinctrl/abx500: adjust offset for get_mode()
pinctrl/abx500: add Device Tree support
pinctrl/abx500: align GPIO cluster boundaries
pinctrl/abx500: prevent error path from corrupting returning error
pinctrl: sunxi: add of_xlate function
pinctrl/lantiq: fix pin number in ltq_pmx_gpio_request_enable
pinctrl/lantiq: add functionality to falcon_pinconf_dbg_show
pinctrl/lantiq: fix pinconfig parameters
pinctrl/lantiq: one of the boot leds was defined incorrectly
pinctrl/lantiq: only probe available pad controllers
...
|
|
Fix sizeof() usage in sh-pfc/core.c to allocate space
for the full data structure instead of a pointer.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch adds the definition for the cldvfs function for Tegra114 pinctrl
support. This is based on work by Pritesh Raithatha.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Rename PIN_CONFIG_INPUT_SCHMITT_DISABLE to
PIN_CONFIG_INPUT_SCHMITT_ENABLE. It's used to make it more generialize.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This is a branch of fixes that originally were scheduled for 3.8 but
due to the request from Linus to hold back on all but the most critical
of fixes, we're re-queueing them for 3.9 here.
* fixes-for-3.9:
ARM: dts: imx6: fix fec ptp clock slow 10 time
ARM: highbank: mask cluster id from cpu_logical_map
ARM: scu: mask cluster id from cpu_logical_map
ARM: scu: add empty scu_enable for !CONFIG_SMP
ARM: at91/at91sam9x5.dtsi: fix usart3 TXD
ARM: at91: at91sam9x5: fix usart3 pinctrl name
ARM: EXYNOS: Fix crash on soft reset on EXYNOS5440
ARM: dts: fix tick and alarm irq numbers for exynos5440
ARM: dts: fix compatible value for exynos pinctrl
ARM: dts: Fix compatible value of pinctrl module on EXYNOS5440
ARM: S3C24XX: fix uninitialized variable warning
mfd/vexpress: vexpress_sysreg_setup must not be __init
ARM: ux500: Fix u9540 booting issues
arm: mvebu: i2c come back in defconfig
arm: plat-orion: fix printing of "MPP config unavailable on this hardware"
Dove: activate GPIO interrupts in DT
ARM: ux500: add spin_unlock(&master_lock).
ARM: ux500: Disable Power Supply and Battery Management by default
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This update adds a debugfs interface to modify a pin configuration
for a given state in the pinctrl map. This allows to modify the
configuration for a non-active state, typically sleep state.
This configuration is not applied right away, but only when the state
will be entered.
This solution is mandated for us by HW validation: in order
to test and verify several pin configurations during sleep without
recompiling the software.
Signed-off-by: Laurent Meunier <laurent.meunier@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch removes duplicated line of samsung_pinctrl_register(),
because the number of pins is redundantly assigned twice.
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Make it harder to do mistakes by introducing the actual
defined ABx500 IRQ number into the IRQ cluster definitions.
Deduct cluster offset from the GPIO offset to make each
cluster coherent.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The ABx500 GPIO controller used to provide a set of virtual contiguous
IRQs for use by sub-devices, but they have been removed after a request
from Mainline Maintainers. Now the AB8500 core driver deals with almost
all IRQ related issues instead.
The ABx500 GPIO driver is now only used to convert between GPIO and IRQ
numbers which is actually quite difficult, as the ABx500 GPIO's
associated IRQs are clustered together throughout the interrupt number
space at irregular intervals. To solve this quandary, we have placed the
read-in values into the existing cluster information table to use during
conversion.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Moved irq_base removal into this patch]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In its current state the gpio-ab8500 driver looks after some GPIO
lines found on the AB8500 MFD chip. It also controls all of its
own IRQ handling for these GPIOs by inventing some virtual IRQs
and handing those out to sub-devices. There has been quite a bit
of controversy over this and it was a contributing factor to the
driver being marked as BROKEN in Mainline.
The reason for adopting this method was due to added complexity
in the hardware. Unusually, each GPIO has two separate IRQs
associated with it, one for a rising and a different one for a
falling interrupt. Using this method complicates matters further
because the GPIO IRQs are actually sandwiched between a bunch
of IRQs which are handled solely by the AB8500 core driver.
The best way for us to take this forward is to get rid of the
virtual IRQs and only hand out the rising IRQ lines. If a
sub-driver wishes to request a falling interrupt, they can do
so by requesting a rising line in the normal way. They just
have to add IRQ_TYPE_EDGE_FALLING or IRQ_TYPE_EDGE_BOTH, if
they require both in the flags. Then if a falling IRQ is
triggered, the AB8500 core driver will know how to handle the
added complexity accordingly. This should greatly simply things.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Augment to keep irq_base for a while (removed later)]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
This removes the __init notation from some of the
the exynos 5440 pin controller set-up functions. These
functions are called from probe() and as such may be
discarded before probe() completes.
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The set_mode() and get_mode() functions in the abx500 were
not mirrored, leading to the wrong GPIO control bits being
read out.
Cc: Lee Jones <lee.jones@linaro.org>
Reported-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch will allow the ABX500 Pinctrl driver to be probed when
Device Tree is enabled with an appropriate node contained.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Not quite sure how this ever worked. In ab8500_gpio_to_irq() the
GPIO for conversion is passed through as the second argument. If
GPIO13, which is a valid GPIO for IRQ functionality, was received;
it would be rejected by the following guard:
GPIO_IRQ_CLUSTER(5, 12, 0); /* GPIO numbers start from 1 */
if (offset >= cluster->start && offset <= cluster->end)
/* Valid GPIO for IRQ use */
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Augmented to account for off-by-one problem]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Prior to this patch abx500_gpio_probe() would return the return-value
of gpiochip_remove() during its error patch regardless of what the
actual failure was. So as long as gpiochip_remove() succeeded, probe()
would look like it succeeded too.
This patch ensures the correct error value is returned and that
mutex_destroy() is invoked if gpiochip_add_pin_range() were to fail.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Since the pin controller of sunxi chips is represented as a
single bank in the driver.
Since this is neither convenient nor represented that way in the
datasheets, define a custom of_xlate function with the layout
<bank pin flag>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The mapping logic inside ltq_pmx_gpio_request_enable() was
broken. This only effected Falcon SoC.
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The current code only has a stub for falcon_pinconf_dbg_show.
This patch adds proper functionality.
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Falcon driver only defined the pinconf parameters but
did not pass them properly to the underlying api.
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
On the Falcon SoC the bootleds are located on pins 9->14.
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The template falcon.dtsi lists all 6 pad controllers that
can be loaded. Only probe those that have status = "okay";
inside the dts file.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When setting the OpenDrain bit we should really honour the
argument passed inside the devicetree.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
While converting the boards inside OpenWrt to OF I noticed
that the we are missing a pinconf parameter to set a pin
to output.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
While converting all the boards supported by OpenWrt to OF
I noticed that this feature is missing. Adding it makes the
devicetrees more readable.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The logic of the OD bit was inverted when calling the
pinconf get method.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The XWAY pinctrl driver invalidly uses the port and not the pin
number to work out the registers and bits to be set for the
opendrain and pullup/down resistors.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
the default of_gpio_simple_xlate() will make us fail while getting gpios
bigger than 32 by of_get_named_gpio() or related APIs.
this patch adds a specific of_xlate callback for sirf gpio_chip and fix
the problem.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Since pinctrl-exynos can support exynos4 and exynos5 so changed
the option name to PINCTRL_EXYNOS for more clarity.
Cc: Thomas Abraham <Thomas.abraham@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Current failure path neglects to mutex_destroy() before returning
an error due to an invalid parameter or an error received from
gpiochip_add(). This patch aims to remedy that behaviour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch provides some superficial changes to the driver to
aid with readability and maintainability. We're mostly fixing
things like white-space errors, spreading out code which as
been clumped together impeding readability and comment layout,
such as using the new "/**" comment start for function headers
etc. No code semantics were harmed in the making of this patch.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Currently in the empty abx500_pin_config_get() function, we're
returning -EINVAL, with a comment stating that the reason for the
failure is that the function isn't implemented yet. Well there's
a proper return code for that. If we use it, we can do away with
the comment too, as it would be implied.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The BIT() macro provides a simple and easy to read way of
obtaining bit offsets into things like masks and hardware
registers. In this patch we're simply replacing all
instances of '1 << x' with 'bit(x)'.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add AB8540 sub driver to the ABx500 family, pins, pin groups and
gpio range.
As the pin controller (also the ABx500 controllers) is an
inherent part of the SoC and will prevent boot if not
available, select this from the Ux500 SoC Kconfig.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add AB9540 sub driver to the ABx500 family, pins, pin groups and
gpio range.
As the pin controller (also the ABx500 controllers) is an
inherent part of the SoC and will prevent boot if not
available, select this from the Ux500 SoC Kconfig.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add AB8505 sub driver to the ABx5x family.
As the pin controller (also the ABx500 controllers) is an
inherent part of the SoC and will prevent boot if not
available, select this from the Ux500 SoC Kconfig.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Linux 3.8-rc6
|
|
Since the Allwinner SoCs variants don't have the same set of pins to
handle, we need to declare the pin ranges available.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds a subdriver for the AB8500 pinctrl portions.
As the pin controller (also the ABx500 controllers) is an
inherent part of the SoC and will prevent boot if not
available, select this from the Ux500 SoC Kconfig.
Acked-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds the AB8500 core driver, which will be utilized by
the follow-on drivers for different ABx500 variants.
Sselect the driver from the DBX500_SOC, as this chip is
powering and clocking that SoC.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
'pinctrl_release' is used only in this file. Hence make it static.
Without this patch we get the following sparse error:
drivers/pinctrl/core.c:815:6: warning:
symbol 'pinctrl_release' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The IP responsible for the muxing on the Allwinner SoCs are also
handling the GPIOs on the system. This patch adds the needed driver that
relies on the pinctrl driver for most of its operations.
The number of pins available for GPIOs operations are already declared
in the pinctrl driver, we only need to probe a generic driver to handle
the banks available for each SoC.
This driver has been tested on a A13-Olinuxino.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
nmk_prcm_gpiocr_get_mode is only needed for debugfs output at
the moment, which can be compile-time disabled. Marking
the function __maybe_unused still gives us compile-time
coverage, but avoids a gcc warning.
Without this patch, building nhk8815_defconfig results in:
drivers/pinctrl/pinctrl-nomadik.c:676:12: warning: 'nmk_prcm_gpiocr_get_mode' defined but not used [-Wunused-function]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jean-Nicolas Graux <jean-nicolas.graux@stericsson.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Functions called from a driver probe() method must not be
marked __init, because they may get called after the
init phase is done, when the device shows up late, or
because of deferred probing.
Without this patch, building exynos_defconfig results in
multiple warnings like:
WARNING: drivers/pinctrl/built-in.o(.text+0x51bc): Section mismatch in reference from the function exynos5440_pinctrl_probe() to the function .init.text:exynos5440_gpiolib_register()
The function exynos5440_pinctrl_probe() references
the function __init exynos5440_gpiolib_register().
This is often because exynos5440_pinctrl_probe lacks a __init
annotation or the annotation of exynos5440_gpiolib_register is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fix the incorrect compatible property value of pinctrl for EXYNOS4 SoCs.
Cc: Thomas Abraham <thomas.ab@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
