Age | Commit message (Collapse) | Author |
|
Ignore the low btemp interrupts for ab8500 3.0 and 3.3
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Hakan Berg <hakan.berg@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Tested-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
The Linux Power Supply framework expects battery temperatures to have
a resolution of 0.1 degree Celsius; however, the AB8500 btemp driver
supplies a battery temperature resolution of 1 degree Celsius. We
therefore have to use a factor 10 on the measured values.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
In case of time out error IRQ needs to be disabled
otherwise we will get unbalanced enable/disable pairs.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
Today the battery recharge is determined with a voltage threshold. This
voltage threshold is only valid when the battery is relaxed. In charging
algorithm the voltage read is the loaded battery voltage and no
compensation is done to get the relaxed voltage. When maintenance
charging is not selected, this makes the recharging condition to almost
immediately activate when there is a discharge present on the battery.
Depending on which vendor the battery comes from this behavior can wear
out the battery much faster than normal.
The fuelgauge driver is responsible to monitor the actual battery
capacity and is able to estimate the remaining capacity. It is better to
use the remaining capacity as a limit to determine when battery should
be recharged.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Reviewed-by: Hakan BERG <hakan.berg@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
Gracefully handle gpadc conversion errors.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Johan BJORNSTEDT <johan.bjornstedt@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
Doing so provides a greater degree of accuracy when dealing with
time-frames between 1us and 20ms. msleep() is only accurate for
wake-ups greater than 20ms.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonas ABERG <jonas.aberg@stericsson.com>
Reviewed-by: Johan BJORNSTEDT <johan.bjornstedt@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
Add two new work queues to provide USB and AC charger disconnect
detection.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
When enabling the CCEOC irq we might get false interrupt
from ab8500-driver due to the latched value will be saved
and interpreted as an IRQ when enabled
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Johan Bjornstedt <johan.bjornstedt@stericsson.com>
Signed-off-by: Henrik Solver <henrik.solver@stericsson.com>
Reviewed-by: Karl KOMIEROWSKI <karl.komierowski@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
Rename the ab8500_power_loss_handling function to a more
descriptive name ab8500_enable_disable_sw_fallback
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Robert Marklund <robert.marklund@stericsson.com>
Reviewed-by: Par-Olof HAKANSSON <par-olof.hakansson@stericsson.com>
Reviewed-by: Karl KOMIEROWSKI <karl.komierowski@stericsson.com>
Tested-by: Par-Olof HAKANSSON <par-olof.hakansson@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
Avoid accessing vc_tbl_ref[3], which is one past the end of that array, in
da9052_determine_vc_tbl_index(), by adjusting the loop bound.
(Hint: there is 'i + 1' inside the loop.)
Signed-off-by: Nickolai Zeldovich <nickolai@csail.mit.edu>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
use devm_kzalloc and no need of error path and unload frees.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
Use 'platform_device' in kernel messages rather than i2c client device
node. lp8788_update_charger_params() needs additional argument, 'pdev'.
Then, remove unnecessary lp8788 private data in lp8788_irq_register().
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
The lp8788-charger is a platform driver of lp8788-mfd. The platform device
is allocated when mfd_add_devices() is called in lp8788-mfd. On the other
hand, 'lp->dev' is the i2c client device.
Therefore, this 'platform_device' is a proper parent device in case of
resource managed mem alloc and device kernel message.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
Some devices, Buffalo Linkstation LS-XHL and LS-CHLv2 for example,
power-off by restarting to letting u-boot hold the SoC until the user
presses a key. Add a generic driver to implement this. It binds a function
to pm_power_off, which calls arm_pm_restart.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
The QNAP NAS boxes have a microcontroller attached to the SoCs second
serial port. By sending it a simple command, it will turn the power for
the board off. This driver registers a function for pm_power_off to send
such a command.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
devm_kzalloc should not be followed by kfree, as this results in a double
free. The problem was found using the following semantic match
(http://coccinelle.lip6.fr/):
// <smpl>
@@
expression x,e;
@@
x = devm_kzalloc(...)
... when != x = e
?-kfree(x,...);
// </smpl>
Furthermore, in the remove function, the calls to free_irq are moved up to
prevent a possible reference in the interrupt handler to resources freed by
power_supply_unregister.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
devm_regulator_get() is device managed and makes error handling and code
cleanup simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Arun Murthy <arun.murthy@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
commit a66f59ba2e994bf70274ef0513e24e0e7ae20c63
bq27x00_battery: Add support for BQ27425 chip
introduced 2 bugs.
1/ 'chip' was set to BQ27425 unconditionally - breaking support for
other devices;
2/ BQ27425 does not support cycle count, how the code still tries to
get the cycle count for BQ27425, and now does it twice for other chips.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: Saranya Gopal <saranya.gopal@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
As most of the charger chips come with two kinds of safety features
related to timing:
1. Watchdog Timer (interms of seconds/mins)
2. Safety Timer (interms of hours)
This patch adds these to fault causes in POWER_SUPPLY_PROP_HEALTH_* enums
so that whenever there is either watchdog timeout or safety timer timeout
driver could notify the user space accurately about the fault and will
also be helpful for debug.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
devm_kzalloc is device managed and makes error handling and code cleanup a
bit simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
module_i2c_driver() makes the code simpler by eliminating module_init and
module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
<linux/version.h> is not required here.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
|
|
There's no need to test whether a (delayed) work item in pending
before queueing, flushing or cancelling it. Most uses are unnecessary
and quite a few of them are buggy.
Remove unnecessary pending tests and rewrite _setup_polling() so that
it uses mod_delayed_work() if the next polling interval is sooner than
currently scheduled. queue_delayed_work() is used otherwise.
Only compile tested. I noticed that two work items - setup_polling
and cm_monitor_work - schedule each other. It's a very unusual
construct and I'm fairly sure it's racy. You can't break such
circular dependency by calling cancel on each. I strongly recommend
revising the mechanism.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Donggeun Kim <dg77.kim@samsung.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
|
|
This patch split _probe function for readability because _probe function
is longer than 400 line.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM cleanups for omap from Olof Johansson:
"From Tony Lindgren:
Here are few more patches to finish the omap changes for multiplatform
conversion that are not strictly fixes, but were too complex to do
with the dependencies during the merge window. Those are to move of
serial-omap.h to platform_data, and the removal of remaining
cpu_is_omap macro usage outside mach-omap2.
Then there are several trivial fixes for typos and few minimal
omap2plus_defconfig updates."
* tag 'omap-late-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arch/arm/mach-omap2/dpll3xxx.c: drop if around WARN_ON
OMAP2: Fix a typo - replace regist with register.
ARM/omap: use module_platform_driver macro
ARM: OMAP2+: PMU: Remove unused header
ARM: OMAP4: remove duplicated include from omap_hwmod_44xx_data.c
ARM: OMAP2+: omap2plus_defconfig: enable twl4030 SoC audio
ARM: OMAP2+: omap2plus_defconfig: Add tps65217 support
ARM: OMAP2+: enable devtmpfs and devtmpfs automount
ARM: OMAP2+: omap_twl: Change TWL4030_MODULE_PM_RECEIVER to TWL_MODULE_PM_RECEIVER
ARM: OMAP2+: Drop plat/cpu.h for omap2plus
ARM: OMAP: Split fb.c to remove last remaining cpu_is_omap usage
MAINTAINERS: Add an entry for omap related .dts files
|
|
Pull battery update, part 2, from Anton Vorontsov:
"These are left overs that I didn't have time to review/apply before
the merge window opened. I didn't want to "spoil" the first pull
request with these late patches, so they were not included:
- A small patch for the RX51 OMAP board (Nokia N900 phone), the patch
creates a battery monitor device instance, so that it can be
probed. It was acked by the OMAP maintainer;
- A couple of late bug fixes for the charger-manager: corrects corner
cases for the battery full handling."
* tag 'for-v3.8-part2' of git://git.infradead.org/battery-2.6:
charger-manager: Fix bug when check dropped voltage after fullbatt event
charger-manager: Fix bug related to checking fully charged state of battery
ARM: OMAP: rx51: Register platform device for rx51_battery
|
|
The cpu_is_omap macros are now local to arch/arm/mach-omap2
in soc.h and plat/cpu.h can finally be dropped for omap2+.
Thanks everybody for help with fixing the drivers.
Note that we can now also remove the unused plat/cpu.h from
smartreflex.c and isp.c as they will cause compile errors
with ARCH_MULTIPLATFORM enabled.
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Jean Pihet <jean.pihet@newoldbits.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch check difference value between current voltage of battery and
desc->fullbatt_uV whether positve or negative number. If difference value
is negative number when current voltage of battery is larger than
desc->fullbatt_uV, charger-manager return immediately because battery is
fully charged.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
|
|
This patch fix bug related to checking fully charged state of battery when
charger-manager call is_full_charged() function. After reading property of
charger/fuel-gauge through power_supply API, val.intval is more than 1.
So, is_full_charged() function always return true. If true, battery means
fully charged state.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFS update from Samuel Ortiz:
"This is the MFD patch set for the 3.8 merge window.
We have several new drivers, most of the time coming with their sub
devices drivers:
- Austria Microsystem's AS3711
- Nano River's viperboard
- TI's TPS80031, AM335x TS/ADC,
- Realtek's MMC/memstick card reader
- Nokia's retu
We also got some notable cleanups and improvements:
- tps6586x got converted to IRQ domains.
- tps65910 and tps65090 moved to the regmap IRQ API.
- STMPE is now Device Tree aware.
- A general twl6040 and twl-core cleanup, with moves to the regmap
I/O and IRQ APIs and a conversion to the recently added PWM
framework.
- sta2x11 gained regmap support.
Then the rest is mostly tiny cleanups and fixes, among which we have
Mark's wm5xxx and wm8xxx patchset."
Far amount of annoying but largely trivial conflicts. Many due to
__devinit/exit removal, others due to one or two of the new drivers also
having come in through another tree.
* tag 'mfd-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (119 commits)
mfd: tps6507x: Convert to devm_kzalloc
mfd: stmpe: Update DT support for stmpe driver
mfd: wm5102: Add readback of DSP status 3 register
mfd: arizona: Log if we fail to create the primary IRQ domain
mfd: tps80031: MFD_TPS80031 needs to select REGMAP_IRQ
mfd: tps80031: Add terminating entry for tps80031_id_table
mfd: sta2x11: Fix potential NULL pointer dereference in __sta2x11_mfd_mask()
mfd: wm5102: Add tuning for revision B
mfd: arizona: Defer patch initialistation until after first device boot
mfd: tps65910: Fix wrong ack_base register
mfd: tps65910: Remove unused data
mfd: stmpe: Get rid of irq_invert_polarity
mfd: ab8500-core: Fix invalid free of devm_ allocated data
mfd: wm5102: Mark DSP memory regions as volatile
mfd: wm5102: Correct default for LDO1_CONTROL_2
mfd: arizona: Register haptics devices
mfd: wm8994: Make current device behaviour the default
mfd: tps65090: MFD_TPS65090 needs to select REGMAP_IRQ
mfd: Fix stmpe.c build when OF is not enabled
mfd: jz4740-adc: Use devm_kzalloc
...
|
|
Pull battery subsystem updates from Anton Vorontsov:
"Highlights:
- Two new drivers from Pali Rohár and N900 hackers: rx51_battery and
bq2415x_charger. The drivers are a part of a solution to replace
the proprietary Nokia BME stack
- Power supply core now registers devices with a thermal cooling
subsystem, so we can now automatically throttle charging. Thanks
to Ramakrishna Pallala!
- Device tree support for ab8500 and max8925_power drivers
- Random fixups and enhancements for a bunch of drivers."
* tag 'for-v3.8-merged' of git://git.infradead.org/battery-2.6: (22 commits)
max8925_power: Add support for device-tree initialization
ab8500: Add devicetree support for chargalg
ab8500: Add devicetree support for charger
ab8500: Add devicetree support for btemp
ab8500: Add devicetree support for fuelgauge
twl4030_charger: Change TWL4030_MODULE_* ids to TWL_MODULE_*
jz4740-battery: Use devm_request_and_ioremap
jz4740-battery: Use devm_kzalloc
bq27x00_battery: Fixup nominal available capacity reporting
bq2415x_charger: Fix style issues
bq2415x_charger: Add Kconfig/Makefile entries
power_supply: Add bq2415x charger driver
power_supply: Add new Nokia RX-51 (N900) power supply battery driver
max17042_battery: Fix missing verify_model_lock() return value check
ds2782_battery: Fix signedness bug in ds278x_read_reg16()
lp8788-charger: Fix ADC channel names
lp8788-charger: Fix wrong ADC conversion
lp8788-charger: Use consumer device name on setting IIO channels
power_supply: Register power supply for thermal cooling device
power_supply: Add support for CHARGE_CONTROL_* attributes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC power management and clock changes from Olof Johansson:
"This branch contains a largeish set of updates of power management and
clock setup. The bulk of it is for OMAP/AM33xx platforms, but also a
few around hotplug/suspend/resume on Exynos.
It includes a split-up of some of the OMAP clock data into separate
files which adds to the diffstat, but gross delta is fairly reasonable."
* tag 'pm-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
ARM: OMAP: Move plat-omap/dma-omap.h to include/linux/omap-dma.h
ASoC: OMAP: mcbsp fixes for enabling ARM multiplatform support
watchdog: OMAP: fixup for ARM multiplatform support
ARM: EXYNOS: Add flush_cache_all in suspend finisher
ARM: EXYNOS: Remove scu_enable from cpuidle
ARM: EXYNOS: Fix soft reboot hang after suspend/resume
ARM: EXYNOS: Add support for rtc wakeup
ARM: EXYNOS: fix the hotplug for Cortex-A15
ARM: OMAP2+: omap_device: Correct resource handling for DT boot
ARM: OMAP2+: hwmod: Add possibility to count hwmod resources based on type
ARM: OMAP2+: hwmod: Add support for per hwmod/module context lost count
ARM: OMAP2+: PRM: initialize some PRM functions early
ARM: OMAP2+: voltage: fixup oscillator handling when CONFIG_PM=n
ARM: OMAP4: USB: power down MUSB PHY during boot
ARM: OMAP2+: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP2xxx: clock: drop obsolete clock data
ARM: OMAP2: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP3+: DPLL: drop !CONFIG_COMMON_CLK sections
ARM: AM33xx: clock: drop obsolete clock data
ARM: OMAP3xxx: clk: drop obsolete clock data
...
|
|
Pull ARM SoC device tree conversions and enablement from Olof Johansson:
"Continued device tree conversion and enablement across a number of
platforms; Kirkwood, tegra, i.MX, Exynos, zynq and a couple of other
smaller series as well.
ux500 has seen continued conversion for platforms. Several platforms
have seen pinctrl-via-devicetree conversions for simpler
multiplatform. Tegra is adding data for new devices/drivers, and
Exynos has a bunch of new bindings and devices added as well.
So, pretty much the same progression in the right direction as the
last few releases."
Fix up conflicts as per Olof.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (185 commits)
ARM: ux500: Rename dbx500 cpufreq code to be more generic
ARM: dts: add missing ux500 device trees
ARM: ux500: Stop registering the PCM driver from platform code
ARM: ux500: Move board specific GPIO info out to subordinate DTS files
ARM: ux500: Disable the MMCI gpio-regulator by default
ARM: Kirkwood: remove kirkwood_ehci_init() from new boards
ARM: Kirkwood: Add support LED of OpenBlocks A6
ARM: Kirkwood: Convert to EHCI via DT for OpenBlocks A6
ARM: kirkwood: Add NAND partiton map for OpenBlocks A6
ARM: kirkwood: Add support second I2C bus and RTC on OpenBlocks A6
ARM: kirkwood: Add support DT of second I2C bus
ARM: kirkwood: Convert mplcec4 board to pinctrl
ARM: Kirkwood: Convert km_kirkwood to pinctrl
ARM: Kirkwood: support 98DX412x kirkwoods with pinctrl
ARM: Kirkwood: Convert IX2-200 to pinctrl.
ARM: Kirkwood: Convert lsxl boards to pinctrl.
ARM: Kirkwood: Convert ib62x0 to pinctrl.
ARM: Kirkwood: Convert GoFlex Net to pinctrl.
ARM: Kirkwood: Convert dreamplug to pinctrl.
ARM: Kirkwood: Convert dockstar to pinctrl.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management update from Zhang Rui:
"Highlights:
- Introduction of thermal policy support, together with three new
thermal governors, including step_wise, user_space, fire_share.
- Introduction of ST-Ericsson db8500_thermal driver and ST-Ericsson
db8500_cpufreq_cooling driver.
- Thermal Kconfig file and Makefile refactor.
- Fixes for generic thermal layer, generic cpucooling, rcar thermal
driver and Exynos thermal driver."
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (36 commits)
Thermal: Fix DEFAULT_THERMAL_GOVERNOR
Thermal: fix a NULL pointer dereference when generic thermal layer is built as a module
thermal: rcar: add rcar_zone_to_priv() macro
thermal: rcar: fixup the unit of temperature
thermal: cpu cooling: allow module builds
thermal: cpu cooling: use const parameter while registering
Thermal: Add ST-Ericsson DB8500 thermal properties and platform data.
Thermal: Add ST-Ericsson DB8500 thermal driver.
drivers/thermal/Makefile refactor
Exynos: Add missing dependency
Refactor drivers/thermal/Kconfig
thermal: cpu_cooling: Make 'notify_device' static
Thermal: Remove the cooling_cpufreq_list.
Thermal: fix bug of counting cpu frequencies.
Thermal: add indent for code alignment.
thermal: rcar_thermal: remove explicitly used devm_kfree/iounap()
thermal: user_space: Add missing static storage class specifiers
thermal: fair_share: Add missing static storage class specifiers
thermal: step_wise: Add missing static storage class specifiers
Thermal: Fix oops and unlocking in thermal_sys.c
...
|
|
The merge is merely to fix conflicts before sending a pull request.
Conflicts:
drivers/power/ab8500_btemp.c
drivers/power/ab8500_charger.c
drivers/power/ab8500_fg.c
drivers/power/abx500_chargalg.c
drivers/power/max8925_power.c
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
|
|
Let's rename the Device Tree node which contains information about
an attached battery to something more easily readable.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Now that we always pass platform specific battery management data
through platform_data instead of obtaining it via different means
depending the way be boot the system (DT or ATAGs); we need to
re-jiggle the way we acquire it in the driver start-up functions.
Now it is wrong for it to be missing, but we still allow Device
Tree code to fiddle with it once we've confirmed it's there.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Now that we always pass platform specific battery management data
through platform_data instead of obtaining it via different means
depending the way be boot the system (DT or ATAGs); we need to
re-jiggle the way we acquire it in the driver start-up functions.
Now it is wrong for it to be missing, but we still allow Device
Tree code to fiddle with it once we've confirmed it's there.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Now that we always pass platform specific battery management data
through platform_data instead of obtaining it via different means
depending the way be boot the system (DT or ATAGs); we need to
re-jiggle the way we acquire it in the driver start-up functions.
Now it is wrong for it to be missing, but we still allow Device
Tree code to fiddle with it once we've confirmed it's there.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Now that we always pass platform specific battery management data
through platform_data instead of obtaining it via different means
depending the way be boot the system (DT or ATAGs); we need to
re-jiggle the way we acquire it in the driver start-up functions.
Now it is wrong for it to be missing, but we still allow Device
Tree code to fiddle with it once we've confirmed it's there.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Currently the AB8500 battery management subsystem receives platform
specific information via two different means depending on how the
platform is booted. If DT is not enabled, a reference to a *_bm_data
data structure containing each platform specific attribute is passed
though platform_data. However, if DT is enabled, then platform_data
is empty and the reference is gained though a DT specific probe
function. There are two issues here 1) the same reference is
being collected each time and 2) the DT way doesn't allow any
provisions to select different platform specific attributes, which
kind of defeats the object.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The platform specific battery management configuration data structure
is currently called 'bat' short for 'battery'; however, it contains
information for all components of the battery management group, rather
than information pertaining to the battery itself - there are other
structures for that. So, in keeping with its structure namesake
'abx500_bm_data', we rename it to 'bm' here. Using similar logic,
we're also renaming 'bmdevs_of_probe' to the more device specific
'ab8500_bm_of_probe'.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
We can actually write bmdevs_of_probe to be easier to follow, use
less lines of code and we can even render a variable unused so
that we can remove it completely.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Simple patch to rectify incorrect tabbing. Also adds some
coding style clean-ups to make it easier to read.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Detect battery type in work queue instead of probe.
This reduces the system boot time with 1.5s.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Karl KOMIEROWSKI <karl.komierowski@stericsson.com>
|
|
The CCMuxOffset bit is not kept set. This will force the
columb counter of the AB8500 to use the measure offset
calibration. This should increase the accuracy of the fuel
gauge.
Signed-off-by: Kalle Komierowski <karl.komierowski@stericsson.com>
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
|
|
There is no state machine in the AB to step up/down the charger
current to avoid dips and spikes on VBUS and VBAT when charging
is started. Instead this is implemented in SW.
Signed-off-by: Johan Bjornstedt <johan.bjornstedt@stericsson.com>
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Karl KOMIEROWSKI <karl.komierowski@stericsson.com>
|
|
property, battery-type shall be one of supported technology type
instead blank
- refer: Documentation/devicetree/bindings/power_supply/ab8500/fg.txt
for the list supported types
- this patch appends to ab8500 bm devs DT binding patch set
ref: commit-id e0f1abeba5c2d8a2183566717d99294fd1a29c2e
git://git.infradead.org/battery-2.6.git
- promote ab8500_fg probe to happen before ab8500_btemp probe as
btemp driver depends on fuelgauge list,
ref: ab8500_fg_get(...)
Signed-off-by: Rajanikanth H.V <rajanikanth.hv@stericsson.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/pm2
From Tony Lindgren:
omap prcm changes via Paul Walmsley <paul@pwsan.com>:
Some miscellaneous OMAP hwmod changes for 3.8, along with a PRM
change needed for one of the hwmod patches to function.
Basic test logs for this branch on top of Tony's
omap-for-v3.8/clock branch at commit
558a0780b0a04862a678f7823215424b4e5501f9 are here:
http://www.pwsan.com/omap/testlogs/hwmod_devel_a_3.8/20121121161522/
However, omap-for-v3.8/clock at 558a0780 does not include some fixes
that are needed for a successful test. With several reverts,
fixes, and workarounds applied, the following test logs were
obtained:
http://www.pwsan.com/omap/testlogs/TEST_hwmod_devel_a_3.8/20121121162719/
which indicate that the series tests cleanly.
* tag 'omap-for-v3.8/devel-prcm-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (49 commits)
ARM: OMAP2+: omap_device: Correct resource handling for DT boot
ARM: OMAP2+: hwmod: Add possibility to count hwmod resources based on type
ARM: OMAP2+: hwmod: Add support for per hwmod/module context lost count
ARM: OMAP2+: PRM: initialize some PRM functions early
ARM: OMAP2+: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP2xxx: clock: drop obsolete clock data
ARM: OMAP2: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP3+: DPLL: drop !CONFIG_COMMON_CLK sections
ARM: AM33xx: clock: drop obsolete clock data
ARM: OMAP3xxx: clk: drop obsolete clock data
ARM: OMAP3: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP44xx: clock: drop obsolete clock data
ARM: OMAP4: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP: hwmod: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP: clock: Switch to COMMON clk
ARM: OMAP2: clock: Add 24xx data using common struct clk
ARM: OMAP3: clock: Add 3xxx data using common struct clk
ARM: AM33XX: clock: add clock data in common clock format
ARM: OMAP4: clock: Add 44xx data using common struct clk
ARM: OMAP2+: clock: add OMAP CCF convenience macros to mach-omap2/clock.h
...
Some context conflicts due to nearby changes resolved in
arch/arm/mach-omap2/io.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
|