| Age | Commit message (Collapse) | Author |
|---|
|
- Added support to post vendor unique events on fc_host.
- Supports adapter, port, ioc, flash and remote port based AEN events.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Added PHY sub-module.
- Implemented interface to obtain stats and to
read/update the fw from the PHY module.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Added diagnostics sub-module to BFA.
- Implemented interface to perform memtest/loopback test
and some other diagnostics tests.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Added flash sub-module.
- Implemented the interface to read/erase/update flash partition.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Added SFP sub-module to BFA.
- Added interface to collect sfp media info and sfp speed.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Added CEE sub-module.
- Added support to collect stats/cee module info
using BSG interface.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Modified the design such that each BFA sub-module will provide
the amount of DMA and KVA memory needed by it and queues the
same request to the global dma and kva info queues.
- During the memory allocation we iterate over this queue to allocate
the dma and kva memory requested by sub-modules.
- The change is needed to avoid requesting the aggregate amount of memory
needed by all the BFA sub-modules as one contiguous chunk.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Introduced partitioning of the BFA resources.
- Added h/w queue ID in CPE messages, firmware uses h/w queue ID
from messages to pick a matching RME queue.
- Added message header to bfa_reqq_produce(). h/w queue ID is set
in the message header and firmware modules use h/w queue ID from
message header instead of from cpqe event.
- Made changes to allow using all 256 queues of Brocade-1860 asic.
Previously only a single queue per queue group was used.
- Added function tag to BFI message header. Only used by FC BFI
messages. Used to translate host tag to firmware tag. bfa_lpuid()
is changed to bfa_fn_lpu() that encodes both PCI function and port
ID in BFI message header.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- If flash controller is halted unconditionally, this results in
illegal write access to flash controller register domain. Since
flash controller registers are only accessible once s_clk is started
- added logic to check for WGN status and halt flash controller only
if it is already running.
- Added check to wait for flash controller halt to be completed before
proceeding with s_clk/l_clk initializations.
- Removed unnecessary reset logic for PMM 1T memory and moved memory
initialization after flash access enable.
- Disable Brocade-1860 asic MBOX interrupt before PLL initialization.
- Remove reset enable for S_CLK/L_CLK after both PLL initializations
are complete.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Updated/added data structures and definitions to support FAA protocol.
- Modified the IOC state machine to support FAA.
- Introduced FAA feature configuration - enable/disable/query.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Add logic to handle the case where PCI mapping goes away when
IOCPF state machine is waiting for semaphore.
- Added logic to unlock hw semaphore if the previos FW boot was
from flash based and the current FW initialization attempt is from OS.
- Added fix to update hbfails and hb_count stats during hwerror event.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Added ASIC block configuration APIs:
- to create/delete/update the physical functions
- to do adapter/port mode configuration
- to query the current ASIC block configuration.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
fixes.
- Added support for 16Gbps.
- Added logic to flush pending mailbox command queue when IOC is disabled.
- Fix to Halt the flash controller during fw initialization - since
when asic blck is programmed flash controller's continuous access
blocks f/w access to flash.
- Added new asic based card types and modified IOC get card model routine.
- Added PLL init fix to do LPU reset every time we do a memory
initialization, since not doing so will cause LPU to be
uninitialized during driver load.
- Added fix to Halt flash controller before PLL initialization.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Introduced IOC poll mechanism which replaces current interrupt
based FW READY method.
- The timer based poll routine in IOC will query the ioc_fwstate
register to see if there is a state change in FW, and sends the READY event.
- Bug fixes in the new asic PLL initialization.
- Added logic to handle CPE/RME queue interrupts before iocfc config done.
1. Use the queue_process flag to see if iocfc configuration is done
in INTX mode.
2. Split the MSIX handler installation in two - one for IOC intr
handler and the other for cpe/rme queue handler - and delay
assigning queue handlers until iocfc config is done in MSIX mode.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Made changes to FCS lport, vport state machines to support vport
enable / disable operations.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Added support for Brocade-1860 Fabric Adapter.
- Made changes to support single firmware image per asic type.
- Combined bfi_cbreg.h and bfi_ctreg.h defines into bfi_reg.h with
only minimal defines used by host.
- Added changes to setup CPE/RME Queue register offsets based on
firmware response.
- Removed queue register offset initializations and added register offsets
to BFI config response message.
- Added Brocade-1860 asic specific interrupt status definitions and
mailbox interfaces.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Add PBC port Disabled condition check.
- Rename incorrectly named LPS I2H messages.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Introduced a generic event notification callback function that
receives IOC_ENABLED, IOC_DISABLED, IOC_FAILED events and notifies the
modules registered for these events.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Avoid the use of hardware defined structure bfi_sge_s for DMA
requests in host.
- Defined a generic address len pair to represent a DMA memory chunk
(bfi_alen_s).
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Remove OS wrapper functions/macros, and as a result remove bfa_os_inc.h.
Signed-off-by: Maggie Zhang <xmzhang@brocade.com>
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Remove SCSI IO callbacks, and as a result remove bfa_cb_ioim.h.
Signed-off-by: Maggie Zhang <xmzhang@brocade.com>
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
First round of fix for the endianess check warnings from make C=2 CF="-D__CHECK_ENDIAN__".
Signed-off-by: Maggie <xmzhang@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This patch addresses the comments from Randy Dunlap (Randy.Dunlap@oracle.com)
regarding comment blocks that begining with "/**". bfa driver comments
currently do not follow kernel-doc convention, we hence replace all
/** with /* and **/ with */.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
We have flattened the BFA hierarchy and also reduced the number of
source and header files we used to have earlier.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
