| Age | Commit message (Collapse) | Author |
|---|
|
- Added PHY sub-module.
- Implemented interface to obtain stats and to
read/update the fw from the PHY module.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Added diagnostics sub-module to BFA.
- Implemented interface to perform memtest/loopback test
and some other diagnostics tests.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Added flash sub-module.
- Implemented the interface to read/erase/update flash partition.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Added SFP sub-module to BFA.
- Added interface to collect sfp media info and sfp speed.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Added CEE sub-module.
- Added support to collect stats/cee module info
using BSG interface.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Added support to collect driver/fw stats.
- Added support to perform adapter/ioc enable, disable operations.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Added logic to initiate a PLOGI to the target, while processing a LOGO
from the same target in Direct attach mode.
- Added logic to generate a FCCT Reject indicating unsupported command,
upon receiving FCCT/FCGS requests.
- Added logic to set the fcpim in offline state and avoid any PRLI retries
if a PRLI response is a reject with a reason Command Not Supported.
- Updated the FDMI Supported/Current speeds.
- Added logic to wait for the response from the firmware before sending
ACC to PLOGI and transitioning to subsequent states - while processing an
Incoming PLOGI in online state.
- Added a wait state in the fcs_vport state machine - For case where
FDISC is in progress and we get a vport delete request we wait for
fdisc response and will transition to the appropriate state based on
rsp status, else its causing both driver/fw resources to be not
freed.
- Remove the fc_credit_recovery module param.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Modified the design such that each BFA sub-module will provide
the amount of DMA and KVA memory needed by it and queues the
same request to the global dma and kva info queues.
- During the memory allocation we iterate over this queue to allocate
the dma and kva memory requested by sub-modules.
- The change is needed to avoid requesting the aggregate amount of memory
needed by all the BFA sub-modules as one contiguous chunk.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Introduced partitioning of the BFA resources.
- Added h/w queue ID in CPE messages, firmware uses h/w queue ID
from messages to pick a matching RME queue.
- Added message header to bfa_reqq_produce(). h/w queue ID is set
in the message header and firmware modules use h/w queue ID from
message header instead of from cpqe event.
- Made changes to allow using all 256 queues of Brocade-1860 asic.
Previously only a single queue per queue group was used.
- Added function tag to BFI message header. Only used by FC BFI
messages. Used to translate host tag to firmware tag. bfa_lpuid()
is changed to bfa_fn_lpu() that encodes both PCI function and port
ID in BFI message header.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- If flash controller is halted unconditionally, this results in
illegal write access to flash controller register domain. Since
flash controller registers are only accessible once s_clk is started
- added logic to check for WGN status and halt flash controller only
if it is already running.
- Added check to wait for flash controller halt to be completed before
proceeding with s_clk/l_clk initializations.
- Removed unnecessary reset logic for PMM 1T memory and moved memory
initialization after flash access enable.
- Disable Brocade-1860 asic MBOX interrupt before PLL initialization.
- Remove reset enable for S_CLK/L_CLK after both PLL initializations
are complete.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Updated/added data structures and definitions to support FAA protocol.
- Modified the IOC state machine to support FAA.
- Introduced FAA feature configuration - enable/disable/query.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Add logic to handle the case where PCI mapping goes away when
IOCPF state machine is waiting for semaphore.
- Added logic to unlock hw semaphore if the previos FW boot was
from flash based and the current FW initialization attempt is from OS.
- Added fix to update hbfails and hb_count stats during hwerror event.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Added ASIC block configuration APIs:
- to create/delete/update the physical functions
- to do adapter/port mode configuration
- to query the current ASIC block configuration.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Added BSG interface support to BFA driver
- Adds support to send ELS/CT FC passthru commands and
few vendor specific BSG requests.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Moved FCS initialization, which internally does the im_port creation
as well as the scsi_host creation before bfa_init.
Once the bfa_init is complete & successful:
- Reset the FCS base port cfg params such as pwwn/nwwn and setup fc host
params - based on the values learned during the ioc getattr request.
- Change needed to support BSG commands even on bfa init failure.
- Model description fixes for Brocade adapters.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Enhancements to FCPIM module.
- Introduced IO tag management to allocate/release IOs to FCPIM module
from a free IOtag pool.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Introduce FC credit recovery.
- Added module parameter to enable/disable credit recovery.
Bug Fixes:
- Removed check for ignoring plogi from initiator in switched fabric mode.
- The ABTS for PLOGI is going out few millisecs earlier due to FW
timer calibration (around 300 miilisecs earlier). So there is a
window if an accept comes during this time HBA would have initiated
an ABORT.
- Added 1 to FC_ELS_TOV for compensating for FW timer.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
fixes.
- Added support for 16Gbps.
- Added logic to flush pending mailbox command queue when IOC is disabled.
- Fix to Halt the flash controller during fw initialization - since
when asic blck is programmed flash controller's continuous access
blocks f/w access to flash.
- Added new asic based card types and modified IOC get card model routine.
- Added PLL init fix to do LPU reset every time we do a memory
initialization, since not doing so will cause LPU to be
uninitialized during driver load.
- Added fix to Halt flash controller before PLL initialization.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Introduced IOC poll mechanism which replaces current interrupt
based FW READY method.
- The timer based poll routine in IOC will query the ioc_fwstate
register to see if there is a state change in FW, and sends the READY event.
- Bug fixes in the new asic PLL initialization.
- Added logic to handle CPE/RME queue interrupts before iocfc config done.
1. Use the queue_process flag to see if iocfc configuration is done
in INTX mode.
2. Split the MSIX handler installation in two - one for IOC intr
handler and the other for cpe/rme queue handler - and delay
assigning queue handlers until iocfc config is done in MSIX mode.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Made changes to FCS lport, vport state machines to support vport
enable / disable operations.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Added support for Brocade-1860 Fabric Adapter.
- Made changes to support single firmware image per asic type.
- Combined bfi_cbreg.h and bfi_ctreg.h defines into bfi_reg.h with
only minimal defines used by host.
- Added changes to setup CPE/RME Queue register offsets based on
firmware response.
- Removed queue register offset initializations and added register offsets
to BFI config response message.
- Added Brocade-1860 asic specific interrupt status definitions and
mailbox interfaces.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Add PBC port Disabled condition check.
- Rename incorrectly named LPS I2H messages.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Introduced a generic event notification callback function that
receives IOC_ENABLED, IOC_DISABLED, IOC_FAILED events and notifies the
modules registered for these events.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Avoid the use of hardware defined structure bfi_sge_s for DMA
requests in host.
- Defined a generic address len pair to represent a DMA memory chunk
(bfi_alen_s).
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Root cause: When kernel crashes, bfa IOC state machine and FW doesn't get
a notification and hence are not cleanly shutdown. So registers holding
driver/IOC state information are not reset back to valid disabled/parking
values. This causes subsequent driver initialization to hang during kdump
kernel boot.
Fix description: during the initialization of first PCI function, reset
corresponding register when unclean shutown is detect by reading chip
registers. This will make sure that ioc/fw gets clean re-initialization.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
Move the initialization of debugfs before bfa init, to enable us to
collect driver/firmware traces if init fails. Also add a printk to
display message on bfa_init failure.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This patch includes fixes for two issues releated to firmware download
implementation: 1) Merged memory leak fix provided by Jesper Juhl
<jj@chaosbits.net>. Basically we need to call release_firmware() after
request_firmware(). 2) fixed issues with the firmware download interface
as pointed out by Rolf Eike Beer <eike@sf-mail.de> in linux-scsi. Rearranged
the code and fixed related function protypes.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
Documentation/trace/events.txt: Remove obsolete sched_signal_send.
writeback: fix global_dirty_limits comment runtime -> real-time
ppc: fix comment typo singal -> signal
drivers: fix comment typo diable -> disable.
m68k: fix comment typo diable -> disable.
wireless: comment typo fix diable -> disable.
media: comment typo fix diable -> disable.
remove doc for obsolete dynamic-printk kernel-parameter
remove extraneous 'is' from Documentation/iostats.txt
Fix spelling milisec -> ms in snd_ps3 module parameter description
Fix spelling mistakes in comments
Revert conflicting V4L changes
i7core_edac: fix typos in comments
mm/rmap.c: fix comment
sound, ca0106: Fix assignment to 'channel'.
hrtimer: fix a typo in comment
init/Kconfig: fix typo
anon_inodes: fix wrong function name in comment
fix comment typos concerning "consistent"
poll: fix a typo in comment
...
Fix up trivial conflicts in:
- drivers/net/wireless/iwlwifi/iwl-core.c (moved to iwl-legacy.c)
- fs/ext4/ext4.h
Also fix missed 'diabled' typo in drivers/net/bnx2x/bnx2x.h while at it.
|
|
This patch removes unused functions, data strucutres, and definitions. It
also includes misc comment and formatting cleanups.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This patch removes some inactive functions and macros.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
|
|
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Fix iotag handling:
1) Update and check io tag for retry case.
2) Clearing upper 3 bits in io tag when an IO completes.
The 3 upper bits in io tags are used for counting FCP exchange retry.
Un-cleared bits will cause firmware to access invalid memory when the
same io tag is used for an IO to a target that doesn't support FCP
exchange retry.
3) Only check the effective bits when validating an iotag.
Other minor fixes:
1) Added trace to get FC header type with assert of unhandled packet received.
Ignore the type FC_TYPE_FC_FSS (FC_XS).
2) Fixed the adapter info display check - to check for fcmode flag even.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Direct attach is not working due to the check of PID in fcxp_send request.
- Added logic to set the lps->lp_pid with the PID assigned for n2n mode.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Made IOC auto_recovery synchronized and not timer based.
- Only one PCI function will attempt to recover and reinitialize
the ASIC on a failure, after all the active PCI fns
acknowledge the IOC failure.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
When the bfa driver is loaded a flogi is sent without the knowledge of
trunking configuration. This normal flogi causes the switch ports
which had trunking enabled to go to persistent offline. Solution is
to store the port configuration (which has trunking info) in the flash
for persistency. The firmware will read this configuration when the
very first fcport enable is received.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
- Move fw trace save logic to bfa_ioc_sm_fail_entry(),
so that fw trace is saved irrespective of the cause of the failure.
- Make bfa_ioc_sm_fail() a failure parking state.
- Rename bfa_ioc_sm_initfail() to a more appropriate bfa_ioc_sm_fail_retry()
as it is no longer a parking state.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Remove unused functions and fix checkpatch errors. Misc cleanups in
comment and formatting.
Signed-off-by: Maggie Zhang <xmzhang@brocade.com>
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Remove OS wrapper functions/macros, and as a result remove bfa_os_inc.h.
Signed-off-by: Maggie Zhang <xmzhang@brocade.com>
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Remove SCSI IO callbacks, and as a result remove bfa_cb_ioim.h.
Signed-off-by: Maggie Zhang <xmzhang@brocade.com>
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Modified scatter gather processing to use the kernel provided
scsi_for_each_sg() macro.
1) Instead of allocating and setting up sgpg in bfa_ioim_sge_setup(),
we only do allocation. As a result, we remove
bfa_ioim_sgpg_setup() and rename bfa_ioim_sge_setup() to
bfa_ioim_sgpg_alloc().
2) bfa_ioim_send_ioreq() call scsi_for_each_sg() to handle both inline
and sgpg setup.
Signed-off-by: Maggie Zhang <xmzhang@brocade.com>
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Removed bfa_drv.c, merged it to bfa_core.c and modified Makefile.
Signed-off-by: Maggie Zhang <xmzhang@brocade.com>
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Cleaned up one line functions.
Signed-off-by: Maggie Zhang <xmzhang@brocade.com>
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Removed unused and empty functions.
Signed-off-by: Maggie Zhang <xmzhang@brocade.com>
Signed-off-by: Jing Huang <xmzhang@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
First round of fix for the endianess check warnings from make C=2 CF="-D__CHECK_ENDIAN__".
Signed-off-by: Maggie <xmzhang@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Fix all sparse check warnings from make C=2.
Signed-off-by: Maggie <xmzhang@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Rename log_level to bfa_log_level to make the global variable more bfa
specific and avoid clashes with other drivers which was causing a
build failure.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
