| Age | Commit message (Collapse) | Author |
|---|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (204 commits)
[SCSI] qla4xxx: export address/port of connection (fix udev disk names)
[SCSI] ipr: Fix BUG on adapter dump timeout
[SCSI] megaraid_sas: Fix instance access in megasas_reset_timer
[SCSI] hpsa: change confusing message to be more clear
[SCSI] iscsi class: fix vlan configuration
[SCSI] qla4xxx: fix data alignment and use nl helpers
[SCSI] iscsi class: fix link local mispelling
[SCSI] iscsi class: Replace iscsi_get_next_target_id with IDA
[SCSI] aacraid: use lower snprintf() limit
[SCSI] lpfc 8.3.27: Change driver version to 8.3.27
[SCSI] lpfc 8.3.27: T10 additions for SLI4
[SCSI] lpfc 8.3.27: Fix queue allocation failure recovery
[SCSI] lpfc 8.3.27: Change algorithm for getting physical port name
[SCSI] lpfc 8.3.27: Changed worst case mailbox timeout
[SCSI] lpfc 8.3.27: Miscellanous logic and interface fixes
[SCSI] megaraid_sas: Changelog and version update
[SCSI] megaraid_sas: Add driver workaround for PERC5/1068 kdump kernel panic
[SCSI] megaraid_sas: Add multiple MSI-X vector/multiple reply queue support
[SCSI] megaraid_sas: Add support for MegaRAID 9360/9380 12GB/s controllers
[SCSI] megaraid_sas: Clear FUSION_IN_RESET before enabling interrupts
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1745 commits)
dp83640: free packet queues on remove
dp83640: use proper function to free transmit time stamping packets
ipv6: Do not use routes from locally generated RAs
|PATCH net-next] tg3: add tx_dropped counter
be2net: don't create multiple RX/TX rings in multi channel mode
be2net: don't create multiple TXQs in BE2
be2net: refactor VF setup/teardown code into be_vf_setup/clear()
be2net: add vlan/rx-mode/flow-control config to be_setup()
net_sched: cls_flow: use skb_header_pointer()
ipv4: avoid useless call of the function check_peer_pmtu
TCP: remove TCP_DEBUG
net: Fix driver name for mdio-gpio.c
ipv4: tcp: fix TOS value in ACK messages sent from TIME_WAIT
rtnetlink: Add missing manual netlink notification in dev_change_net_namespaces
ipv4: fix ipsec forward performance regression
jme: fix irq storm after suspend/resume
route: fix ICMP redirect validation
net: hold sock reference while processing tx timestamps
tcp: md5: add more const attributes
Add ethtool -g support to virtio_net
...
Fix up conflicts in:
- drivers/net/Kconfig:
The split-up generated a trivial conflict with removal of a
stale reference to Documentation/networking/net-modules.txt.
Remove it from the new location instead.
- fs/sysfs/dir.c:
Fairly nasty conflicts with the sysfs rb-tree usage, conflicting
with Eric Biederman's changes for tagged directories.
|
|
To ease skb->truesize sanitization, its better to be able to localize
all references to skb frags size.
Define accessors : skb_frag_size() to fetch frag size, and
skb_frag_size_{set|add|sub}() to manipulate it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Except for obtaining the netdev from lport, fcoe_get_lesb is the common code
for the LLDs.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Acked-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Currently fcoe_ddp_min doesn't have default value
so by default not used, so setting up default value
as 4k as this works better by avoiding overhead
of programing DDP for small IOs.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Use real dev in case it has HW vlan acceleration
support since in this case the real dev would
do needed vlan processing, this way unnecessary
vlan layer processing avoided and it gives
slightly better IOPS with 512B size IOs.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Since fcoe_percpu_thread_create() creates percpu kthread, it makes sense
to use kthread_create_on_node() to get proper NUMA affinity for kthread
stack.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Conflicts:
MAINTAINERS
drivers/net/Kconfig
drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c
drivers/net/ethernet/broadcom/tg3.c
drivers/net/wireless/iwlwifi/iwl-pci.c
drivers/net/wireless/iwlwifi/iwl-trans-tx-pcie.c
drivers/net/wireless/rt2x00/rt2800usb.c
drivers/net/wireless/wl12xx/main.c
|
|
This patch does several things:
- introduces __ethtool_get_settings which is called from ethtool code and
from drivers as well. Put ASSERT_RTNL there.
- dev_ethtool_get_settings() is replaced by __ethtool_get_settings()
- changes calling in drivers so rtnl locking is respected. In
iboe_get_rate was previously ->get_settings() called unlocked. This
fixes it. Also prb_calc_retire_blk_tmo() in af_packet.c had the same
problem. Also fixed by calling __dev_get_by_index() instead of
dev_get_by_index() and holding rtnl_lock for both calls.
- introduces rtnl_lock in bnx2fc_vport_create() and fcoe_vport_create()
so bnx2fc_if_create() and fcoe_if_create() are called locked as they
are from other places.
- use __ethtool_get_settings() in bonding code
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
v2->v3:
-removed dev_ethtool_get_settings()
-added ASSERT_RTNL into __ethtool_get_settings()
-prb_calc_retire_blk_tmo - use __dev_get_by_index() and lock
around it and __ethtool_get_settings() call
v1->v2:
add missing export_symbol
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> [except FCoE bits]
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fast-forward merge with Linus to be able to merge patches
based on more recent version of the tree.
|
|
It was pointed out by 'make versioncheck' that some includes of
linux/version.h are not needed in drivers/scsi/.
This patch removes them.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The rtnl cannot be held durrng the fcoe_interface_put.
If it is the last reference on the fcoe_interface the
fcoe_ctlr_destroy will be called as a part of the
cleanup, ultimately calling cancel_work_sync(&fip->recv_work);
If we are processing a flogi response we will be in
the recv_work context and we will lock the rtnl to
add a new unicast MAC address. This is how the deadlock
can occur.
The fix is simply to move the rtnl_lock/unlock into
fcoe_interface_cleanup so that it can be unlocked before
fcoe_interface_put is called.
Here is the lockdep report:
Jul 21 11:26:35 bubba [ 223.870702]
ul 21 11:26:35 bubba [ 223.870704] =======================================================
Jul 21 11:26:35 bubba [ 223.871255] [ INFO: possible circular locking dependency detected ]
Jul 21 11:26:35 bubba [ 223.871530] 3.0.0-rc7+ #1
Jul 21 11:26:35 bubba [ 223.871797] -------------------------------------------------------
Jul 21 11:26:35 bubba [ 223.872072] lockdeptest.sh/3464 is trying to acquire lock:
Jul 21 11:26:35 bubba [ 223.872345] ((&fip->recv_work)
Jul 21 11:26:35 bubba ){+.+.+.}
Jul 21 11:26:35 bubba , at:
Jul 21 11:26:35 bubba [<ffffffff810531f1>] wait_on_work+0x0/0xbd
Jul 21 11:26:35 bubba [ 223.873022]
Jul 21 11:26:35 bubba [ 223.873023] but task is already holding lock:
Jul 21 11:26:35 bubba [ 223.873555] (rtnl_mutex
Jul 21 11:26:35 bubba ){+.+.+.}
Jul 21 11:26:35 bubba , at:
Jul 21 11:26:35 bubba [<ffffffff813e8233>] rtnl_lock+0x12/0x14
Jul 21 11:26:35 bubba [ 223.874229]
Jul 21 11:26:35 bubba [ 223.874230] which lock already depends on the new lock.
Jul 21 11:26:35 bubba [ 223.874231]
Jul 21 11:26:35 bubba [ 223.875032]
Jul 21 11:26:35 bubba [ 223.875033] the existing dependency chain (in reverse order) is:
Jul 21 11:26:35 bubba [ 223.875573]
Jul 21 11:26:35 bubba [ 223.875573] -> #1
Jul 21 11:26:35 bubba (rtnl_mutex
Jul 21 11:26:35 bubba ){+.+.+.}
Jul 21 11:26:35 bubba :
Jul 21 11:26:35 bubba [ 223.876301]
Jul 21 11:26:35 bubba [<ffffffff8106c14a>] lock_acquire+0xd2/0xf7
Jul 21 11:26:35 bubba [ 223.876645]
Jul 21 11:26:35 bubba [<ffffffff8151d975>] __mutex_lock_common+0x47/0x30d
Jul 21 11:26:35 bubba [ 223.876991]
Jul 21 11:26:35 bubba [<ffffffff8151dd36>] mutex_lock_nested+0x3b/0x40
Jul 21 11:26:35 bubba [ 223.877334]
Jul 21 11:26:35 bubba [<ffffffff813e8233>] rtnl_lock+0x12/0x14
Jul 21 11:26:35 bubba [ 223.877675]
Jul 21 11:26:35 bubba [<ffffffffa003d5a0>] fcoe_update_src_mac+0x2b/0x80 [fcoe]
Jul 21 11:26:35 bubba [ 223.878022]
Jul 21 11:26:35 bubba [<ffffffffa003d698>] fcoe_flogi_resp+0x5e/0x79 [fcoe]
Jul 21 11:26:35 bubba [ 223.878366]
Jul 21 11:26:35 bubba [<ffffffffa001566f>] fc_exch_recv+0x7f5/0x9da [libfc]
Jul 21 11:26:35 bubba [ 223.878713]
Jul 21 11:26:35 bubba [<ffffffffa00327d8>] fcoe_ctlr_recv_work+0x71f/0x10dc [libfcoe]
Jul 21 11:26:35 bubba [ 223.879258]
Jul 21 11:26:35 bubba [<ffffffff81053761>] process_one_work+0x1d7/0x347
Jul 21 11:26:35 bubba [ 223.879601]
Jul 21 11:26:35 bubba [<ffffffff81054ade>] worker_thread+0xf8/0x17c
Jul 21 11:26:35 bubba [ 223.879944]
Jul 21 11:26:35 bubba [<ffffffff81058184>] kthread+0x7d/0x85
Jul 21 11:26:35 bubba [ 223.880287]
Jul 21 11:26:35 bubba [<ffffffff81526414>] kernel_thread_helper+0x4/0x10
Jul 21 11:26:35 bubba [ 223.880634]
Jul 21 11:26:35 bubba [ 223.880635] -> #0
Jul 21 11:26:35 bubba ((&fip->recv_work)
Jul 21 11:26:35 bubba ){+.+.+.}
Jul 21 11:26:35 bubba :
Jul 21 11:26:35 bubba [ 223.881357]
Jul 21 11:26:35 bubba [<ffffffff8106b93e>] __lock_acquire+0xb1d/0xe2c
Jul 21 11:26:35 bubba [ 223.881695]
Jul 21 11:26:35 bubba [<ffffffff8106c14a>] lock_acquire+0xd2/0xf7
Jul 21 11:26:35 bubba [ 223.882033]
Jul 21 11:26:35 bubba [<ffffffff81053241>] wait_on_work+0x50/0xbd
Jul 21 11:26:35 bubba [ 223.882378]
Jul 21 11:26:35 bubba [<ffffffff81053b32>] __cancel_work_timer+0xb6/0xf4
Jul 21 11:26:35 bubba [ 223.882718]
Jul 21 11:26:35 bubba [<ffffffff81053b8a>] cancel_work_sync+0xb/0xd
Jul 21 11:26:35 bubba [ 223.883057]
Jul 21 11:26:35 bubba [<ffffffffa00317e6>] fcoe_ctlr_destroy+0x1d/0x67 [libfcoe]
Jul 21 11:26:35 bubba [ 223.883399]
Jul 21 11:26:35 bubba [<ffffffffa003e51e>] fcoe_interface_release+0x21/0x45 [fcoe]
Jul 21 11:26:35 bubba [ 223.883940]
Jul 21 11:26:35 bubba [<ffffffff811fbbe6>] kref_put+0x43/0x4d
Jul 21 11:26:35 bubba [ 223.884280]
Jul 21 11:26:35 bubba [<ffffffffa003ebba>] fcoe_interface_put+0x17/0x19 [fcoe]
Jul 21 11:26:35 bubba [ 223.884624]
Jul 21 11:26:35 bubba [<ffffffffa003f2a6>] fcoe_interface_cleanup+0x188/0x193 [fcoe]
Jul 21 11:26:35 bubba [ 223.885163]
Jul 21 11:26:35 bubba [<ffffffffa003f303>] fcoe_destroy+0x52/0x72 [fcoe]
Jul 21 11:26:35 bubba [ 223.885502]
Jul 21 11:26:35 bubba [<ffffffffa00340a4>] fcoe_transport_destroy+0xab/0x110 [libfcoe]
Jul 21 11:26:35 bubba [ 223.886045]
Jul 21 11:26:35 bubba [<ffffffff81056153>] param_attr_store+0x43/0x62
Jul 21 11:26:35 bubba [ 223.886385]
Jul 21 11:26:35 bubba [<ffffffff8105602d>] module_attr_store+0x21/0x25
Jul 21 11:26:35 bubba [ 223.886728]
Jul 21 11:26:35 bubba [<ffffffff8114c23d>] sysfs_write_file+0x103/0x13f
Jul 21 11:26:35 bubba [ 223.887068]
Jul 21 11:26:35 bubba [<ffffffff810f3e7b>] vfs_write+0xa7/0xfa
Jul 21 11:26:35 bubba [ 223.887406]
Jul 21 11:26:35 bubba [<ffffffff810f4073>] sys_write+0x45/0x69
Jul 21 11:26:35 bubba [ 223.887742]
Jul 21 11:26:35 bubba [<ffffffff815252bb>] system_call_fastpath+0x16/0x1b
Jul 21 11:26:35 bubba [ 223.888083]
Jul 21 11:26:35 bubba [ 223.888084] other info that might help us debug this:
Jul 21 11:26:35 bubba [ 223.888085]
Jul 21 11:26:35 bubba [ 223.888879] Possible unsafe locking scenario:
Jul 21 11:26:35 bubba [ 223.888881]
Jul 21 11:26:35 bubba [ 223.889411] CPU0 CPU1
Jul 21 11:26:35 bubba [ 223.889683] ---- ----
Jul 21 11:26:35 bubba [ 223.889955] lock(
Jul 21 11:26:35 bubba rtnl_mutex
Jul 21 11:26:35 bubba );
Jul 21 11:26:35 bubba [ 223.890349] lock(
Jul 21 11:26:35 bubba (&fip->recv_work)
Jul 21 11:26:35 bubba );
Jul 21 11:26:35 bubba [ 223.890751] lock(
Jul 21 11:26:35 bubba rtnl_mutex
Jul 21 11:26:35 bubba );
Jul 21 11:26:35 bubba [ 223.891154] lock(
Jul 21 11:26:35 bubba (&fip->recv_work)
Jul 21 11:26:35 bubba );
Jul 21 11:26:35 bubba [ 223.891549]
Jul 21 11:26:35 bubba [ 223.891550] *** DEADLOCK ***
Jul 21 11:26:35 bubba [ 223.891551]
Jul 21 11:26:35 bubba [ 223.892347] 6 locks held by lockdeptest.sh/3464:
Jul 21 11:26:35 bubba [ 223.892621] #0:
Jul 21 11:26:35 bubba (&buffer->mutex
Jul 21 11:26:35 bubba ){+.+.+.}
Jul 21 11:26:35 bubba , at:
Jul 21 11:26:35 bubba [<ffffffff8114c171>] sysfs_write_file+0x37/0x13f
Jul 21 11:26:35 bubba [ 223.893359] #1:
Jul 21 11:26:35 bubba (s_active
Jul 21 11:26:35 bubba ){++++.+}
Jul 21 11:26:35 bubba , at:
Jul 21 11:26:35 bubba [<ffffffff8114c21c>] sysfs_write_file+0xe2/0x13f
Jul 21 11:26:35 bubba [ 223.894094] #2:
Jul 21 11:26:35 bubba (param_lock
Jul 21 11:26:35 bubba ){+.+.+.}
Jul 21 11:26:35 bubba , at:
Jul 21 11:26:35 bubba [<ffffffff81056146>] param_attr_store+0x36/0x62
Jul 21 11:26:35 bubba [ 223.894835] #3:
Jul 21 11:26:35 bubba (ft_mutex
Jul 21 11:26:35 bubba ){+.+.+.}
Jul 21 11:26:35 bubba , at:
Jul 21 11:26:35 bubba [<ffffffffa0034017>] fcoe_transport_destroy+0x1e/0x110 [libfcoe]
Jul 21 11:26:35 bubba [ 223.895574] #4:
Jul 21 11:26:35 bubba (fcoe_config_mutex
Jul 21 11:26:35 bubba ){+.+.+.}
Jul 21 11:26:35 bubba , at:
Jul 21 11:26:35 bubba [<ffffffffa003f2c9>] fcoe_destroy+0x18/0x72 [fcoe]
Jul 21 11:26:35 bubba [ 223.896314] #5:
Jul 21 11:26:35 bubba (rtnl_mutex
Jul 21 11:26:35 bubba ){+.+.+.}
Jul 21 11:26:35 bubba , at:
Jul 21 11:26:35 bubba [<ffffffff813e8233>] rtnl_lock+0x12/0x14
Jul 21 11:26:35 bubba [ 223.897047]
Jul 21 11:26:35 bubba [ 223.897048] stack backtrace:
Jul 21 11:26:35 bubba [ 223.897578] Pid: 3464, comm: lockdeptest.sh Not tainted 3.0.0-rc7+ #1
Jul 21 11:26:35 bubba [ 223.897853] Call Trace:
Jul 21 11:26:35 bubba [ 223.898128] [<ffffffff81068e16>] print_circular_bug+0x1f8/0x209
Jul 21 11:26:35 bubba [ 223.898416] [<ffffffff8106b93e>] __lock_acquire+0xb1d/0xe2c
Jul 21 11:26:35 bubba [ 223.898699] [<ffffffff810531f1>] ? wait_on_cpu_work+0xe6/0xe6
Jul 21 11:26:35 bubba [ 223.898982] [<ffffffff8106c14a>] lock_acquire+0xd2/0xf7
Jul 21 11:26:35 bubba [ 223.899263] [<ffffffff810531f1>] ? wait_on_cpu_work+0xe6/0xe6
Jul 21 11:26:35 bubba [ 223.899547] [<ffffffff8104a097>] ? mod_timer+0x8f/0x98
Jul 21 11:26:35 bubba [ 223.899827] [<ffffffff81053241>] wait_on_work+0x50/0xbd
Jul 21 11:26:35 bubba [ 223.900108] [<ffffffff810531f1>] ? wait_on_cpu_work+0xe6/0xe6
Jul 21 11:26:35 bubba [ 223.900390] [<ffffffff81053b32>] __cancel_work_timer+0xb6/0xf4
Jul 21 11:26:35 bubba [ 223.900671] [<ffffffff81053b8a>] cancel_work_sync+0xb/0xd
Jul 21 11:26:35 bubba [ 223.900953] [<ffffffffa00317e6>] fcoe_ctlr_destroy+0x1d/0x67 [libfcoe]
Jul 21 11:26:35 bubba [ 223.901237] [<ffffffffa003e51e>] fcoe_interface_release+0x21/0x45 [fcoe]
Jul 21 11:26:35 bubba [ 223.901522] [<ffffffffa003e4fd>] ? fcoe_enable+0x6b/0x6b [fcoe]
Jul 21 11:26:35 bubba [ 223.901803] [<ffffffff811fbbe6>] kref_put+0x43/0x4d
Jul 21 11:26:35 bubba [ 223.902083] [<ffffffffa003ebba>] fcoe_interface_put+0x17/0x19 [fcoe]
Jul 21 11:26:35 bubba [ 223.902367] [<ffffffffa003f2a6>] fcoe_interface_cleanup+0x188/0x193 [fcoe]
Jul 21 11:26:35 bubba [ 223.902653] [<ffffffff8151dd36>] ? mutex_lock_nested+0x3b/0x40
Jul 21 11:26:35 bubba [ 223.902939] [<ffffffffa003f303>] fcoe_destroy+0x52/0x72 [fcoe]
Jul 21 11:26:35 bubba [ 223.903223] [<ffffffffa00340a4>] fcoe_transport_destroy+0xab/0x110 [libfcoe]
Jul 21 11:26:35 bubba [ 223.903508] [<ffffffff81056153>] param_attr_store+0x43/0x62
Jul 21 11:26:35 bubba [ 223.903792] [<ffffffff8105602d>] module_attr_store+0x21/0x25
Jul 21 11:26:35 bubba [ 223.904075] [<ffffffff8114c23d>] sysfs_write_file+0x103/0x13f
Jul 21 11:26:35 bubba [ 223.904357] [<ffffffff810f3e7b>] vfs_write+0xa7/0xfa
Jul 21 11:26:35 bubba [ 223.904642] [<ffffffff810f51d6>] ? fget_light+0x35/0x96
Jul 21 11:26:35 bubba [ 223.904923] [<ffffffff810f4073>] sys_write+0x45/0x69
Jul 21 11:26:35 bubba [ 223.905204] [<ffffffff815252bb>] system_call_fastpath+0x16/0x1b
Jul 21 11:26:36 bubba [ 223.964438] ixgbe 0000:05:00.0: eth3: detected SFP+: 5
Jul 21 11:26:37 bubba [ 225.196702] ixgbe 0000:05:00.0: eth3: NIC Link is Up 10 Gbps, Flow Control: None
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Reviewed-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Export fcoe_get_wwn, fcoe_validate_vport_create and fcoe_wwn_to_str so that all
LLDs can use these common function.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Robert Love <robert.w.love@intel.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: devel@open-fcoe.org
Cc: linux-scsi@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cleanup to:
- have selection for all types of frames, not just FCP.
- remove redundant cpu_online check once fcoe_select_cpu called
as this is not required since later code flow check for offlined
cpu.
- Simplify fcoe_select_cpu() by removing unnecessary checks to
skip curr_cpu, this also fixes possibly infinite loop in case
of curr_cpu is the only cpu while iterating in the loop.
This cleanup mainly applies to target as incoming request are
mostly for target, therefore Kiran has verified the patch
with target also.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Use pending queue to retry FIP frame in case its tx
fails and use common pending queue for both fcoe
and fip frames using fcoe_port_send.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Drop the rx frame having xid with wrong cpu info
or received with xid not matching to our xid.
Not dropping such frame is causing panic as
that causes accessing data struct beyond their
bounds.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
There is no need to cache the ptype in fcoe_rcv_info struct as it is never
used anywhere.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
When NPIV port destroy handler is called it does not do all the cleanup
required for the given NPIV port. This was happening as some of the
lport cleanup moved to fcoe_interface_cleanup() routine, which is not
called as part of the vport delete process.
This patch rearranges the sequence in which the fcoe_if_destory() and
fcoe_interface_cleanup() functions are being called from various places
in the code. It now matches the sequence they are constructed during the
create process for both N_Port as well as NPIV port.
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
post processing of incoming request for FCoE target
Problem: Selection of RX queue on target is based on RX-ID. FCoE used
8 Net Rx queues. HW post the packets based on rx_id %
num_rx_queue. Due to this has based filtering, only one CPU is busy
servicing incoming request including post-processing of incoming
request. This is gating factor because
1. Only one CPU is utilized 100% while others CPUs are not used at all.
2. CPU which received request assign "sequence' by selecting exchange
from per CPU pool (num_ddp_context / num_online_cpus,
approxi.). Due to which if if rate of incoming request is higher
than rate of servicing request, existing code path end of sending
"BUSY" response (SAM_STAT_BUSY because unable to allocate
exchange).
Fix: Fan-out incoming request to all other CPUs excluding the CPU
which is receiving all incoiming request. This path also addresses,
selecting same CPU based on rx_id from received frame for completion
of the request such as "releasing exchange to the per CPU Pool". This
fix is applicable for FCoE target since initiator code path already
takes care of selecting CPU to complete post-processing of request
once OX_ID is assigned.
Notes: N/A
Dependencines: N/A
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
incoming commands
Problem: Earlier mechanism of selection of CPU was, to select the same CPU
which has received incoming request. Hence in case of rx_id = 0xFFFF,
request was always posted to same NetRx queue, hence only 1 CPU is utilized
for handling the command. It was also causing problem of "running out of
exchanges from per CPU pool of exchanges (in case of DDP offload)
Fix: Implemented new algo. to select CPU for post-processing of
incoming commands when rx_id is unknown. This is simple Round robin
algo. for CPU selection.
Notes/Dependencies: N/A
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
targets
Problem: When initiator sends write command to target, target tries to
assign new sequence. It allocates new exchangeID (RX_ID)
always from non-offloaded pool (Non-offload EMA)
Fix: Enhanced fcoe_oem_match routine to look at F_CTL flags and if it
is exchange responder and command type is WRITEDATA, then function
returns TRUE instead of FALSE. This function is used to determine
which pool to use (offload pool of exchange is used only if this
function returns TRUE).
Technical Notes: N/A
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Add ddp_target() support to the Open-FCoE sw fcoe hba driver (fcoe.ko).
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
libfcoe's interface consists of create, destroy, enable,
disable and create_vn2vn. These are currently module
paramaters added durring the module initialization. A
concern arose that the module parameters were being added
with write permissions before the module had completed
initialization. The following code was added to each
sysfs store file.
* Make sure the module has been initialized, and is not about to be
* removed. Module parameter sysfs files are writable before the
* module_init function is called and after module_exit.
*/
if (THIS_MODULE->state != MODULE_STATE_LIVE)
goto out_nodev;
This check was called out as unhelpful as the module can
go dead at any time and therefore its state isn't a reliable
thing to look at as a sign of stability and initialization
completion. Also, that functional interfaces like these
should be added after module initialization.
This patch removes the unnecessary checks and hopes to
disprove the concern about initialization ordering.
Recent fcoe transport rework changes now require fcoe
transports to register with libfcoe before any operation
can take place. libfcoe may access some static variables
but nothing that could cause a problem. Once a fcoe transport
is registered, libfcoe is usable and any interface calls will
be functional.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
This patch adds a validation step before allowing creation of a new NPIV port.
It checks whether the WWPN passed for the new NPIV port to be created is unique
for the given physical port.
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
Host doesnt handle CVL to NPIV instantiated ports correctly.
- As per FC-BB-5 Rev 2 CVLs with no VN_Port descriptors shall be treated as
implicit logout of ALL vn_ports.
- CVL for NPIV ports should be handled before physical port even if descriptor
for physical port appears before NPIV ports
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1446 commits)
macvlan: fix panic if lowerdev in a bond
tg3: Add braces around 5906 workaround.
tg3: Fix NETIF_F_LOOPBACK error
macvlan: remove one synchronize_rcu() call
networking: NET_CLS_ROUTE4 depends on INET
irda: Fix error propagation in ircomm_lmp_connect_response()
irda: Kill set but unused variable 'bytes' in irlan_check_command_param()
irda: Kill set but unused variable 'clen' in ircomm_connect_indication()
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_transport()
be2net: Kill set but unused variable 'req' in lancer_fw_download()
irda: Kill set but unused vars 'saddr' and 'daddr' in irlan_provider_connect_indication()
atl1c: atl1c_resume() is only used when CONFIG_PM_SLEEP is defined.
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_peer().
rxrpc: Kill set but unused variable 'local' in rxrpc_UDP_error_handler()
rxrpc: Kill set but unused variable 'sp' in rxrpc_process_connection()
rxrpc: Kill set but unused variable 'sp' in rxrpc_rotate_tx_window()
pkt_sched: Kill set but unused variable 'protocol' in tc_classify()
isdn: capi: Use pr_debug() instead of ifdefs.
tg3: Update version to 3.119
tg3: Apply rx_discards fix to 5719/5720
...
Fix up trivial conflicts in arch/x86/Kconfig and net/mac80211/agg-tx.c
as per Davem.
|
|
Currently fcoe interface cleanup is done after ndo_fcoe_disable
and that prevents logoff going out to the peer, so this patch
moves all netdev cleanup and its releasing inside
fcoe_interface_cleanup to have log off before ndo_fcoe_disable
disables the fcoe.
This patch also fixes asymmetric rtnl locking around fcoe_if_destroy,
as currently this function requires rtnl held by its caller
and then have this func drops the lock, instead now don't have
any processing under rtnl inside fcoe_if_destroy, this required
moving few func to get build working again.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
fix typo of '_attach' -> '_detach' in the comment.
Reported-by: Frank Zhang <frank_1.zhang@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
possible buffer overflow in fcoe_transport_show when reaching the end of
buffer and crossing PAGE_SIZE boundary.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
When rmmoving the underlying fcoe transport driver module by force when
it's attached and in use, the correspoding netdev mapping should be
cleaned up properly as well, otherwise the lookup for a given netdev
for the transport would still return non NULL pointer, causing "unable
to handle paging request" bug.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
list_del()/list_add() combination
Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The check of module state being MODULE_STATE_LIVE is no longer needed for the
individual fcoe transport driver, e.g., fcoe.ko, as sysfs entries now go to
libfcoe now, if it reaches fcoe.ko, it has to be already registered. The module
state check for libfcoe will guard the possible race condition of sysfs being
writable before module_init function is called and after module_exit.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
These checks were initially added to avoid a lockdep
false positive when dealing with the s_active, rtnl
and fcoe_config_mutex mutexes. Recently the create,
destroy, enable and disable sysfs entries were moved
from fcoe.ko to libfcoe.ko. With this change the mutex
usage was shuffled around and the lockdep false
positive stopped happening. We can now remove these
checks.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This code was incorrectly ported from fcoe.c when the
fcoe transport infrastructure was put into place. It
was originally needed in fcoe.c when dealing with
the rtnl mutex. In that code it was only needed to
avoid a lockdep false positive. In libfcoe we don't
deal with the rtnl mutex, we don't get the lockdep
false positive and therefore we don't need these
checks.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This makes sure that when a driver calls the ethtool's
get/set_settings() callback of another driver, the data passed to it
is clean. This guarantees that speed_hi will be zeroed correctly if
the called callback doesn't explicitely set it: we are sure we don't
get a corrupted speed from the underlying driver. We also take care of
setting the cmd field appropriately (ETHTOOL_GSET/SSET).
This applies to dev_ethtool_get_settings(), which now makes sure it
sets up that ethtool command parameter correctly before passing it to
drivers. This also means that whoever calls dev_ethtool_get_settings()
does not have to clean the ethtool command parameter. This function
also becomes an exported symbol instead of an inline.
All drivers visible to make allyesconfig under x86_64 have been
updated.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (170 commits)
[SCSI] scsi_dh_rdac: Add MD36xxf into device list
[SCSI] scsi_debug: add consecutive medium errors
[SCSI] libsas: fix ata list corruption issue
[SCSI] hpsa: export resettable host attribute
[SCSI] hpsa: move device attributes to avoid forward declarations
[SCSI] scsi_debug: Logical Block Provisioning (SBC3r26)
[SCSI] sd: Logical Block Provisioning update
[SCSI] Include protection operation in SCSI command trace
[SCSI] hpsa: fix incorrect PCI IDs and add two new ones (2nd try)
[SCSI] target: Fix volume size misreporting for volumes > 2TB
[SCSI] bnx2fc: Broadcom FCoE offload driver
[SCSI] fcoe: fix broken fcoe interface reset
[SCSI] fcoe: precedence bug in fcoe_filter_frames()
[SCSI] libfcoe: Remove stale fcoe-netdev entries
[SCSI] libfcoe: Move FCOE_MTU definition from fcoe.h to libfcoe.h
[SCSI] libfc: introduce __fc_fill_fc_hdr that accepts fc_hdr as an argument
[SCSI] fcoe, libfc: initialize EM anchors list and then update npiv EMs
[SCSI] Revert "[SCSI] libfc: fix exchange being deleted when the abort itself is timed out"
[SCSI] libfc: Fixing a memory leak when destroying an interface
[SCSI] megaraid_sas: Version and Changelog update
...
Fix up trivial conflicts due to whitespace differences in
drivers/scsi/libsas/{sas_ata.c,sas_scsi_host.c}
|
|
Check for bonding master and refuse to use that.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Robert Love <robert.w.love@intel.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reset using "fcoeadm -r" also needs to restart FIP before
doing libfc lport reset, this is needed for new switch firmware
requiring FIP solicitation before doing FLOGI again during reset.
So this patch does this by doing fcoe_ctlr_link_down and then
fcoe_ctlr_link_up to reset the interface.
The fcoe_ctlr_link_down call path also does lport reset
and then fcoe_ctlr_link_up re-starts the fabric login after
doing FIP solicitation first to get reset feature working
again.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Negate has higher precedence than bitwise AND. FCPHF_CRC_UNCHECKED is
0x1 so the original code is equivalent to: if (!fr_flags(fp)) { ...
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
When L2 driver is unloaded, libfcoe_destroy tries to access the fcoe
transport structure matching the netdev. However, since the netdev is
unregistered by that time, it fails to do so. Hence the stale mappings
exists in the fcoe-netdev list. Handle NETDEV_UREGISTER device
notification mechanism to remove the stale fcoe-netdev mapping.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
both fcoe and bnx2fc drivers can access the common definition of
FCOE_MTU.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
EM anchors list initialization for only master port was not enough to
keep npiv working as described here:-
https://lists.open-fcoe.org/pipermail/devel/2011-January/011063.html
So this patch moves fc_exch_mgr_list_clone to update npiv ports
EMs once EM anchors list initialized.
Also some cleanup, no need to set lport = NULL as that always
get initialized later.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
To facilitate LLDDs to reuse the code, skb queue related functions are moved to
libfcoe, so that both fcoe and bnx2fc drivers can use them. The common structures
fcoe_port, fcoe_percpu_s are moved to libfcoe. fcoe_port will now have an
opaque pointer that points to corresponding driver's interface structure.
Also, fcoe_start_io and fcoe_fc_crc are moved to libfcoe.
As part of this change, fixed fcoe_start_io to return ENOMEM if
skb_clone fails.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
fcoe uses the system_wq to destroy ports and the work items need to be
flushed before the driver is unloaded. As the work items free the
containing data structure, they can't be flushed directly. The
workqueue should be flushed instead.
Also, the destruction works can be chained - ie. destruction of a port
may lead to destruction of another port where the work item for the
former queues the work for the latter. Currently, the depth of chain
can be at most two and fcoe_exit() makes sure everything is complete
by calling flush_scheduled_work() twice.
With commit c8efcc25 (workqueue: allow chained queueing during
destruction), destroy_workqueue() can take care of chained works on
workqueue destruction. Add and use fcoe_wq instead. Simply
destroying fcoe_wq on driver unload takes care of flushing.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Remove the existing sysfs entry points of the fcoe.ko module parameters that
are used to create/destroy/enable/disable an FCoE instance, rather, use the
newly added fcoe transport code to attach itself as an FCoE transport provider
when fcoe.ko gets loaded. There is no functionality change on the logic of
fcoe interacts with upper libfc and lower netdev. The fcoe transport only acts
as thin layer to provide a unified interface for all fcoe transport providers
so all FCoE instances on any network interfaces from all vendors can be
managed through the same Open-FCoE.org's user space tool package, which also
has full DCB support.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Prepare the fcoe to convert it to use the newly added fcoe transport, making
it as the default fcoe transport provider for libfcoe. This patch is to rename
some of the variables to avoid any confusing names later as now there are
several transports in the same file.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Now we can include the fcoe_transport.c to the build of the kernel libfcoe
module. Move the module information to fcoe_transport, and it will have
all the module parameters later for the create/destroy/enable/disable of an
FCoE instance.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The existing libfcoe.c is mostly for FIP support, rename it to reflect that
fact and so we can add fcoe_transport.c to the make file to include both
into the libfcoe kernel module.
[ Minor modifications by Robert Love converting a few
"__attribute__((packed))" modifiers to "__packed" to remove new
checkpatch.pl WARNINGS ]
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
