summaryrefslogtreecommitdiff
path: root/drivers/serial/8250.c
AgeCommit message (Collapse)Author
2010-03-12serial 8250: enable PPS supportRodolfo Giometti
Automagically function serial8250_enable_ms() is called when PPS ldisc is selected. Signed-off-by: Rodolfo Giometti <giometti@linux.it> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Greg KH <greg@kroah.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Alexander Gordeev <lasaine@lvk.cs.msu.su> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-02serial: copy UART properties of UPF_FIXED_TYPE ports provisioned using ↵Shmulik Ladkani
early_serial_setup Augment the UPF_FIXED_TYPE logic, which currently applies to UART ports provisioned using platform_device_register. The suggested patch applies same logic into 'serial8250_register_ports', making UART ports provisioned using early_serial_setup inherit their properties from the uart_config entry. Signed-off-by: Shmulik Ladkani <shmulik@jungo.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-02-27SERIAL 8250: Fixes for Alchemy UARTs.Manuel Lauss
Limit the amount of address space claimed for Alchemy serial ports to 0x1000. On the Au1300, ports are only 0x1000 apart, and the registers only extend to 0x110 at most on all supported alchemy models. On the Au1300 the autodetect logic no longer works and this makes it necessary to specify the port type through platform data. Because of this the MSR quirk needs to be moved outside the autoconfig() function which will no longer be called when UPF_FIXED_TYPE is specified. Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org>, Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2010-02-16serial: 8250: add serial transmitter fully empty testDick Hollenbeck
When controlling an industrial radio modem it can be necessary to manipulate the handshake lines in order to control the radio modem's transmitter, from userspace. The transmitter should not be turned off before all characters have been transmitted. serial8250_tx_empty() was reporting that all characters were transmitted before they actually were. === Discovered in parallel with more testing and analysis by Kees Schoenmakers as follows: I ran into an NetMos 9835 serial pci board which behaves a little different than the standard. This type of expansion board is very common. "Standard" 8250 compatible devices clear the 'UART_LST_TEMT" bit together with the "UART_LSR_THRE" bit when writing data to the device. The NetMos device does it slightly different I believe that the TEMT bit is coupled to the shift register. The problem is that after writing data to the device and very quickly after that one does call serial8250_tx_empty, it returns the wrong information. My patch makes the test more robust (and solves the problem) and it does not affect the already correct devices. Alan: We may yet need to quirk this but now we know which chips we have a way to do that should we find this breaks some other 8250 clone with dodgy THRE. Signed-off-by: Dick Hollenbeck <dick@softplc.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Cc: Kees Schoenmakers <k.schoenmakers@sigmae.nl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-11Serial: Do not read IIR in serial8250_start_tx when UART_BUG_TXENIan Jackson
Do not read IIR in serial8250_start_tx when UART_BUG_TXEN Reading the IIR clears some oustanding interrupts so it is not safe. Instead, simply transmit immediately if the buffer is empty without regard to IIR. Signed-off-by: Ian Jackson <ian.jackson@eu.citrix.com> Reviewed-by: Markus Armbruster <armbru@redhat.com> Reviewed-by: Jiri Kosina <jkosina@suse.cz> Cc: Alan Cox <alan@linux.intel.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-11serial, 8250: calculate irqflags bitmask before loopAndré Goddard Rosa
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-11-12serial: fix printk format specifiers for struct uart_port::iobaseLennert Buytenhek
struct uart_port::iobase is unsigned long, so use %lx as printk format specifier. Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01serial: add parameter to force skipping the test for the TXEN bugChuck Ebbert
Allow users to force skipping the TXEN test at init time. Applies to all serial ports. Intended for debugging only. There is a blacklist for devices where we need to skip the test but the list is not complete. This lets users force skipping the test so we can determine if they need to be added to the list. Some HP machines with weird serial consoles have this problem and there may be more. Signed-off-by: Chuck Ebbert <cebbert@redhat.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-19serial: move delta_msr_wait into the tty_portAlan Cox
This is used by various drivers not just serial and can be extracted as commonality Signed-off-by: Alan Cox <alan@linux.intel.com>
2009-09-19serial: kill off uart_infoAlan Cox
We moved this into uart_state, now move the fields out of the separate structure and kill it off. Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-09-198250: Now honours baud rate lower boundsAnton Vorontsov
A platform clock drives 8250 ports in most SOC systems, the clock might run at high frequencies, and so it's not always possible to downscale uart clock to a desired value. Currently the 8250 uart driver accepts not supported baud rates, and what is worse, it is doing this silently, and then passes not accepted values to a new termios, so userspace has no chance to catch this kind of errors (userspace verifies that settings were accepted by reading back and comparing the settings). This patch fixes the issue by passing minimum baud rate to the uart_get_baud_rate() call, the call should take care of all bounds, so userspace should now report: # stty -F /dev/ttyS0 speed 300 115200 stty: /dev/ttyS0: unable to perform all requested operations p.s. uart_get_baud_rate() falls back to 9600, which still might be too low for some 10 GHz platforms, but that's a separate issue, and we can wait with fixing this till we find such a platform. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-09-19serial: 8250: add IRQ trigger supportVikram Pandita
There is currently no provision for passing IRQ trigger flags for serial IRQs with triggering requirements (such as GPIO IRQs) This patch adds irqflags to plat_serial8250_port that can be passed from board file to reqest_irq() of 8250 driver Changes are backward compatible with boards passing UPF_SHARE_IRQ flag Tested on Zoom2 board that has IRQF_TRIGGER_RISING requirement for 8250 irq [Moved new flag to end to fix bugs in the original with the old_serial array -- Alan] Signed-off-by: Vikram Pandita <vikram.pandita@ti.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-06-11serial: add support for the TI AR7 internal UARTFlorian Fainelli
This patch adds support for the TI AR7 internal UART. Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-05-298250: Fix oops from setserialAlan Cox
If you setserial a port which has never been initialised we change the type but don't update the I/O method pointers. The same problem is true if you change the io type of a port - but nobody ever does that so nobody noticed! Remember the old type and when attaching if the type has changed reload the port accessor pointers. We can't do it blindly as some 8250 drivers load custom accessors and we must not stomp those. Tested-by: Victor Seryodkin <vvscore@gmail.com> Closes-bug: #13367 Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-02-218250: fix boot hang with serial console when using with Serial Over Lan portMauro Carvalho Chehab
Intel 8257x Ethernet boards have a feature called Serial Over Lan. This feature works by emulating a serial port, and it is detected by kernel as a normal 8250 port. However, this emulation is not perfect, as also noticed on changeset 7500b1f602aad75901774a67a687ee985d85893f. Before this patch, the kernel were trying to check if the serial TX is capable of work using IRQ's. This were done with a code similar this: serial_outp(up, UART_IER, UART_IER_THRI); lsr = serial_in(up, UART_LSR); iir = serial_in(up, UART_IIR); serial_outp(up, UART_IER, 0); if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT) up->bugs |= UART_BUG_TXEN; This works fine for other 8250 ports, but, on 8250-emulated SoL port, the chip is a little lazy to down UART_IIR_NO_INT at UART_IIR register. Due to that, UART_BUG_TXEN is sometimes enabled. However, as TX IRQ keeps working, and the TX polling is now enabled, the driver miss-interprets the IRQ received later, hanging up the machine until a key is pressed at the serial console. This is the 6 version of this patch. Previous versions were trying to introduce a large enough delay between serial_outp and serial_in(up, UART_IIR), but not taking forever. However, the needed delay couldn't be safely determined. At the experimental tests, a delay of 1us solves most of the cases, but still hangs sometimes. Increasing the delay to 5us was better, but still doesn't solve. A very high delay of 50 ms seemed to work every time. However, poking around with delays and pray for it to be enough doesn't seem to be a good approach, even for a quirk. So, instead of playing with random large arbitrary delays, let's just disable UART_BUG_TXEN for all SoL ports. [akpm@linux-foundation.org: fix warnings] Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-13fix early_serial_setup() regressionHelge Deller
Commit b430428a188e8a434325e251d0704af4b88b4711 ("8250: Don't clobber spinlocks.") introduced a regression on the parisc architecture, which broke the handover to the serial port at boottime. early_serial_setup() was changed to only copy a subset of the uart_port fields, and sadly the "type" and "line" fields were forgotten and thus the serial port was not initialized and could not be used for a handover. This patch fixes this by copying the missing fields. As this change to early_serial_setup() doesn't need an initialized spinlock in the uart_port struct any longer, we can drop the spinlock initialization in the superio driver. Cc: David Daney <ddaney@caviumnetworks.com> Cc: Tomaso Paoletti <tpaoletti@caviumnetworks.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Acked-by: Kyle McMartin <kyle@mcmartin.ca> Cc: linux-parisc@vger.kernel.org Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-06trivial: Add a space (and a comma) to a printk in 8250 driverPaul Bolle
Commit d87a6d9 ("drivers/serial/: remove CVS keywords") removed one space too many in the printk in serial8250_init(). Put it back in (and add a comma for clarity). Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-01-02Serial: UART driver changes for Cavium OCTEON.David Daney
Cavium UART implementation is not covered by existing uart_configS. Define a new uart_config (PORT_OCTEON) which is specified by OCTEON platform device registration code. Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com> Signed-off-by: David Daney <ddaney@caviumnetworks.com> Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-02Serial: Allow port type to be specified when calling serial8250_register_port.David Daney
Add flag value UPF_FIXED_TYPE which specifies that the UART type is known and should not be probed. For this case the UARTs properties are just copied out of the uart_config entry. This allows us to keep SOC specific 8250 probe code out of 8250.c. In this case we know the serial hardware will not be changing as it is on the same silicon as the CPU, and we can specify it with certainty in the board/cpu setup code. The alternative is to load up 8250.c with a bunch of OCTEON specific special cases in the probing code. Signed-off-by: David Daney <ddaney@caviumnetworks.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-028250: Serial driver changes to support future Cavium OCTEON serial patches.David Daney
In order to use Cavium OCTEON specific serial i/o drivers, we first patch the 8250 driver to use replaceable I/O functions. Compatible I/O functions are added for existing iotypeS. An added benefit of this change is that it makes it easy to factor some of the existing special cases out to board/SOC specific support code. The alternative is to load up 8250.c with a bunch of OCTEON specific iotype code and bug work-arounds. Signed-off-by: David Daney <ddaney@caviumnetworks.com> Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-028250: Don't clobber spinlocks.David Daney
In serial8250_isa_init_ports(), the port's lock is initialized. We should not overwrite it. In early_serial_setup(), only copy in the fields we need. Since the early console code only uses a subset of the fields, these are sufficient. Signed-off-by: David Daney <ddaney@caviumnetworks.com> Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20Merge branch 'genirq-v28-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip This merges branches irq/genirq, irq/sparseirq-v4, timers/hpet-percpu and x86/uv. The sparseirq branch is just preliminary groundwork: no sparse IRQs are actually implemented by this tree anymore - just the new APIs are added while keeping the old way intact as well (the new APIs map 1:1 to irq_desc[]). The 'real' sparse IRQ support will then be a relatively small patch ontop of this - with a v2.6.29 merge target. * 'genirq-v28-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (178 commits) genirq: improve include files intr_remapping: fix typo io_apic: make irq_mis_count available on 64-bit too genirq: fix name space collisions of nr_irqs in arch/* genirq: fix name space collision of nr_irqs in autoprobe.c genirq: use iterators for irq_desc loops proc: fixup irq iterator genirq: add reverse iterator for irq_desc x86: move ack_bad_irq() to irq.c x86: unify show_interrupts() and proc helpers x86: cleanup show_interrupts genirq: cleanup the sparseirq modifications genirq: remove artifacts from sparseirq removal genirq: revert dynarray genirq: remove irq_to_desc_alloc genirq: remove sparse irq code genirq: use inline function for irq_to_desc genirq: consolidate nr_irqs and for_each_irq_desc() x86: remove sparse irq from Kconfig genirq: define nr_irqs for architectures with GENERIC_HARDIRQS=n ...
2008-10-16Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (51 commits) [ARM] 5308/1: Fix Viper ISA IRQ handling [ARM] 5307/1: pxa: fix CM-X2XX PCMCIA build error [ARM] 5306/1: pxa: fix build error on CM-X270 [ARM] 5302/1: ARM: OMAP: Revert omap3 WDT changes to avoid merge conflict [ARM] 5305/1: ARM: OMAP: Fix compile of McBSP by removing unnecessary check [ARM] 5301/1: ARM: OMAP: Add missing irq defines ARM: OMAP3: Add default kernel config for OMAP LDP ARM: OMAP3: Add basic board support for OMAP LDP ARM: OMAP3: Defconfig for the Gumstix Overo board (rev 3) ARM: OMAP3: Add support for the Gumstix Overo board (rev 3) ARM: OMAP3: Add Beagle defconfig ARM: OMAP3: Add minimal Beagle board support ARM: OMAP3: Add minimal omap3430 support ARM: OMAP2: Fix sparse, checkpatch warnings in OMAP2/3 IRQ code ARM: OMAP: Fixes to omap_mcbsp_request function ARM: OMAP: Add support for OMAP2430 in McBSP ARM: OMAP: Add support for McBSP devices 3 - 5 on 34xx ARM: OMAP: Allocate McBSP devices dynamically Fix sections for omap-mcbsp platform driver [ARM] S3C24XX: Additional include moves ...
2008-10-16drivers/serial: use nr_irqsYinghai Lu
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-10-16serial, 8250: remove NR_IRQ usageAlan Cox
Works on my test box with a quick test. Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-10-15Merge branch 'fixes' into for-linusRussell King
Conflicts: arch/arm/mach-versatile/core.c
2008-10-148250: Fix lock warning (and possible crash)Alan Cox
Splitting the 8250 code back up to avoid a clash with the NR_IRQS removal patch introduced a last minute bug. Put back the additional needed lines for the old lock init Signed-off-by: Alan Cox <alan@redhat.com> [ Ingo also reports that this can cause a spontaneous reboot crash with certain configs, and sends in an identical patch ] Tested-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-13serial: fix device name reporting when minor space is shared between driversDavid S. Miller
The multiple drivers share the minor space occupied by a particular major number, the actual index within the device name's space is indicated by the tty_driver->name_base + uart_port->line Another usable formula is (uart_driver->minor - MINOR_BASE) + port->line Use those to print the device names properly in such situations in serial_core.c and 8250.c Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-13serial: allow 8250 to be used on sparcDavid Miller
This requires three changes: 1) Remove !SPARC restriction in Kconfig. 2) Move Sparc specific serial drivers before 8250, so that serial console devices don't change names on us, even if 8250 finds devices. 3) Since the Sparc specific serial drivers try to use the same major/minor device namespace as 8250, some coordination is necessary. Use the sunserial_*() layer routines to allocate minor number space within TTY_MAJOR when CONFIG_SPARC. This has no effect on other platforms. Thanks to Josip Rodin for bringing up this issue and testing plus debugging various revisions of this patch. Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-138250: remove a few inlines of dubious valueWill Newton
Remove some inlines from various functions that are called once, are too big to inline, or are called only from slow path code. This saves around 300 bytes of code for me. Signed-off-by: Will Newton <will.newton@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-09-05[SERIAL] 8250: serial8250_port_size() - omap ports are largerRussell King
A function to contain common code for the size of the resource we need to allocate or free. OMAP ports need 22 bytes rather than the standard 8 bytes. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-05[ARM] omap: improve is_omap_port()Russell King
Make is_omap_port() take the uart_8250_port structure so it can do whatever test it desires. Convert the test to compare the physical addresses rather than virtual addresses. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-038250: improve workaround for UARTs that don't re-assert THRE correctlyWill Newton
Recent changes to tighten the check for UARTs that don't correctly re-assert THRE (01c194d9278efc15d4785ff205643e9c0bdcef53: "serial 8250: tighten test for using backup timer") caused problems when such a UART was opened for the second time - the bug could only successfully be detected at first initialization. For users of this version of this particular UART IP it is fatal. This patch stores the information about the bug in the bugs field of the port structure when the port is first started up so subsequent opens can check this bit even if the test for the bug fails. David Brownell: "My own exposure to this is that the UART on DaVinci hardware, which TI allegedly derived from its original 16550 logic, has periodically gone from working to unusable with the mainline 8250.c ... and back and forth a bunch. Currently it's "unusable", a regression from some previous versions. With this patch from Will, it's usable." Signed-off-by: Will Newton <will.newton@gmail.com> Acked-by: Alex Williamson <alex.williamson@hp.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: David Brownell <david-b@pacbell.net> Cc: <stable@kernel.org> [2.6.26.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-308250.c: port.lock is irq-safeBorislav Petkov
serial8250_startup() doesn't disable interrupts while taking the &up->port.lock which might race against the interrupt handler serial8250_interrupt(), which when entered, will deadlock waiting for the lock to be released. Signed-off-by: Borislav Petkov <petkovbb@gmail.com> Tested-by: Ingo Molnar <mingo@elte.hu> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-248250: fix break handling for Intel 82571Aristeu Rozanski
Intel 82571 has a "Serial Over LAN" feature that doesn't properly implements the receiving of break characters. When a break is received, it doesn't set UART_LSR_DR and unless another character is received, the break won't be received by the application. Signed-off-by: Aristeu Rozanski <arozansk@redhat.com> Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-22serial: 8250: fix shared interrupts issues with SMP and RT kernelsAnton Vorontsov
With SMP kernels _irqsave spinlock disables only local interrupts, while the shared serial interrupt could be assigned to the CPU that is not currently starting up the serial port. This might cause issues because serial8250_startup() routine issues IRQ-triggering operations before registering the port in the IRQ chain (though, this is fine to do and done explicitly because we don't want to process any interrupts on the port startup). With RT kernels and preemptable hardirqs, _irqsave spinlock does not disable local hardirqs, and the bug could be reproduced much easily: $ cat /dev/ttyS0 & $ cat /dev/ttyS1 irq 42: nobody cared (try booting with the "irqpoll" option) Call Trace: [C0475EB0] [C0008A98] show_stack+0x4c/0x1ac (unreliable) [C0475EF0] [C004BBD4] __report_bad_irq+0x34/0xb8 [C0475F10] [C004BD38] note_interrupt+0xe0/0x308 [C0475F50] [C004B09C] thread_simple_irq+0xdc/0x104 [C0475F70] [C004B3FC] do_irqd+0x338/0x3c8 [C0475FC0] [C00398E0] kthread+0xf8/0x100 [C0475FF0] [C0011FE0] original_kernel_thread+0x44/0x60 handlers: [<c02112c4>] (serial8250_interrupt+0x0/0x138) Disabling IRQ #42 After this, all serial ports on the given IRQ are non-functional. To fix the issue we should explicitly disable shared IRQ before issuing any IRQ-triggering operations. I also changed spin_lock_irqsave to the ordinary spin_lock, since it seems to be safe: chain does not contain new port (yet), thus nobody will interfere us from the ISRs. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-21serial: use tty_portAlan Cox
Switch the serial_core based drivers to use the new tty_port structure. We can't quite use all of it yet because of the dynamically allocated extras in the serial_core layer. Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-21drivers/serial/: remove CVS keywordsAdrian Bunk
This patch removes CVS keywords that weren't updated for a long time in comments, printk's and MODULE_DESCRIPTION's (no printk's or MODULE_DESCRIPTION's are completely removed). While doing this I also found and fixed a missing \n in a printk in m32r_sio.c Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-12serial8250: sanity check nr_uarts on all paths.Eric W. Biederman
I had 8250.nr_uarts=16 in the boot line of a test kernel and I had a weird mysterious crash in sysfs. After taking an in-depth look I realized that CONFIG_SERIAL_8250_NR_UARTS was set to 4 and I was walking off the end of the serial8250_ports array. Ouch!!! Don't let this happen to someone else. Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Acked-by: Alan Cox <alan@redhat.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-318250 Serial Driver: revert extra IRQ flag definition patchBryan Wu
As Russell pointed out, original patch will break some serial configurations because of the dependency of the <asm/serial.h> header file. Revert it first and try to find out other solution later Cc: Javier Herrero <jherrero@hvsistemas.es> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Russell King <rmk+lkml@arm.linux.org.uk> Signed-off-by: Bryan Wu <cooloney@kernel.org>
2008-05-178250 Serial Driver: Added support for 8250-class UARTs in HV Sistemas H8606 ↵Javier Herrero
board Added support for 8250-class UARTs in HV Sistemas H8606 board, modification in 8250.c driver for correct compilation with Blackfin Besides, I think that there is more people using 8250-class UARTs with a different hardware than the H8606 board. This code can be shared by them. Signed-off-by: Javier Herrero <jherrero@hvsistemas.es> Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Bryan Wu <cooloney@kernel.org>
2008-05-018250: switch 8250 drivers to use _nocache ioremapsAlan Cox
Signed-off-by: Alan Cox <alan@redhat.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28serial 8250: tighten test for using backup timerAlex Williamson
Thomas Koeller had reported an issue where a device that had been making use of the UART_BUG_TXEN code in the 8250 driver was mistakenly being caught by the backup timer test, causing the device to work improperly. To fix this, tighten the test requirements to enable the backup timer workaround. The backup timer is really meant to catch UARTs that don't re-assert the THRE interrupt. The expectation is that they do initially assert THRE. This patch clarifies the test. Signed-off-by: Alex Williamson <alex.williamson@hp.com> Cc: Thomas Koeller <thomas@koeller.dyndns.org> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28Fix tty speed handling on 8250Alan Cox
We try and write the correct speed back but the serial midlayer already mangles the speed on us and that means if we request B0 we report back B9600 when we should not. For now we'll hack around this in the drivers and serial code, pending a better long term solution. Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-17consoles: polling support, kgdbocJason Wessel
polled console handling support, to access a console in an irq-less way while in debug or irq context. absolutely zero impact as long as CONFIG_CONSOLE_POLL is disabled. (which is the default) [ jan.kiszka@siemens.com: lots of cleanups ] [ mingo@elte.hu: redesign, splitups, cleanups. ] Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Jan Kiszka <jan.kiszka@web.de> Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
2008-02-088250: enable rate reporting via termiosAlan Cox
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-08serial8250: coding styleAlan Cox
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05serial: Coding styleAlan Cox
Coding style tweaks and printk levels. Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-058250.c: support specifying DW APB UARTs in device platform_dataWill Newton
Allow the private_data field to be specified in platform_data for the standard 8250/16550 UART. This field is used by DW APB type UARTs and without this patch it's only possible to set this field when registering the port by hand. If private_data is not set then the driver will potentially oops with a NULL pointer dereference. Signed-off-by: Will Newton <will.newton@gmail.com> Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-08-23Serial 8250: handle saving the clear-on-read bits from the LSR and MSRCorey Minyard
Reading the LSR clears the break, parity, frame error, and overrun bits in the 8250 chip, but these are not being saved in all places that read the LSR. Same goes for the MSR delta bits. Save the LSR bits off whenever the lsr is read so they can be handled later in the receive routine. Save the MSR bits to be handled in the modem status routine. Also, clear the stored bits and clear the interrupt registers before enabling interrupts, to avoid handling old values of the stored bits in the interrupt routines. [akpm@linux-foundation.org: clean up pre-existing code] Signed-off-by: Corey Minyard <minyard@acm.org> Cc: Russell King <rmk+lkml@arm.linux.org.uk> Cc: Yinghai Lu <yinghai.lu@sun.com> Cc: Bjorn Helgaas <bjorn.helgaas@hp.com> Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>