| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Scott Wood <scottwood@freescale.com>
Conflicts:
arch/arm/kvm/mmu.c
arch/arm/mm/proc-v7-3level.S
arch/powerpc/kernel/vdso32/getcpu.S
drivers/crypto/caam/error.c
drivers/crypto/caam/sg_sw_sec4.h
drivers/usb/host/ehci-fsl.c
|
|
On 07/27/2011 04:37 PM, Thomas Gleixner wrote:
> - KGDB (not yet disabled) is reportedly unusable on -rt right now due
> to missing hacks in the console locking which I dropped on purpose.
>
To work around this in the short term you can use this patch, in
addition to the clocksource watchdog patch that Thomas brewed up.
Comments are welcome of course. Ultimately the right solution is to
change separation between the console and the HW to have a polled mode
+ work queue so as not to introduce any kind of latency.
Thanks,
Jason.
|
|
Beyond the warning:
drivers/tty/serial/8250/8250.c:1613:6: warning: unused variable ‘pass_counter’ [-Wunused-variable]
the solution of just looping infinitely was ugly - up it to 1 million to
give it a chance to continue in some really ugly situation.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
In -RT the spin_lock_irqsave() does not spin but sleep if the lock is
taken. Before that, local_irq_save() is invoked which disables
interrupts even on -RT. Therefore local_irq_save() + spin_lock() does not
work.
In the ->sysrq and oops_in_progress case it is save to trylock the lock
i.e. this is what we do now anyway except for ->sysrq where we assume
that the lock is already taken.
The spin_lock_irqsave() grabs the lock and disables the interrupts on
vanilla (the same behavior) and on -RT it won't disable interrupts.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[bigeasy: add a patch description]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
|
|
|
|
On 07/27/2011 04:37 PM, Thomas Gleixner wrote:
> - KGDB (not yet disabled) is reportedly unusable on -rt right now due
> to missing hacks in the console locking which I dropped on purpose.
>
To work around this in the short term you can use this patch, in
addition to the clocksource watchdog patch that Thomas brewed up.
Comments are welcome of course. Ultimately the right solution is to
change separation between the console and the HW to have a polled mode
+ work queue so as not to introduce any kind of latency.
Thanks,
Jason.
|
|
Beyond the warning:
drivers/tty/serial/8250/8250.c:1613:6: warning: unused variable ‘pass_counter’ [-Wunused-variable]
the solution of just looping infinitely was ugly - up it to 1 million to
give it a chance to continue in some really ugly situation.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
In -RT the spin_lock_irqsave() does not spin but sleep if the lock is
taken. Before that, local_irq_save() is invoked which disables
interrupts even on -RT. Therefore local_irq_save() + spin_lock() does not
work.
In the ->sysrq and oops_in_progress case it is save to trylock the lock
i.e. this is what we do now anyway except for ->sysrq where we assume
that the lock is already taken.
The spin_lock_irqsave() grabs the lock and disables the interrupts on
vanilla (the same behavior) and on -RT it won't disable interrupts.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[bigeasy: add a patch description]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
|
|
|
|
This merges 3.12.15-rt25.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Conflicts:
drivers/misc/Makefile
drivers/net/ethernet/freescale/gianfar.c
drivers/net/ethernet/freescale/gianfar_ethtool.c
drivers/net/ethernet/freescale/gianfar_sysfs.c
|
|
On 07/27/2011 04:37 PM, Thomas Gleixner wrote:
> - KGDB (not yet disabled) is reportedly unusable on -rt right now due
> to missing hacks in the console locking which I dropped on purpose.
>
To work around this in the short term you can use this patch, in
addition to the clocksource watchdog patch that Thomas brewed up.
Comments are welcome of course. Ultimately the right solution is to
change separation between the console and the HW to have a polled mode
+ work queue so as not to introduce any kind of latency.
Thanks,
Jason.
|
|
Beyond the warning:
drivers/tty/serial/8250/8250.c:1613:6: warning: unused variable ‘pass_counter’ [-Wunused-variable]
the solution of just looping infinitely was ugly - up it to 1 million to
give it a chance to continue in some really ugly situation.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
In -RT the spin_lock_irqsave() does not spin but sleep if the lock is
taken. Before that, local_irq_save() is invoked which disables
interrupts even on -RT. Therefore local_irq_save() + spin_lock() does not
work.
In the ->sysrq and oops_in_progress case it is save to trylock the lock
i.e. this is what we do now anyway except for ->sysrq where we assume
that the lock is already taken.
The spin_lock_irqsave() grabs the lock and disables the interrupts on
vanilla (the same behavior) and on -RT it won't disable interrupts.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[bigeasy: add a patch description]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
|
|
Signed-off-by: Scott Wood <scottwood@freescale.com>
Conflicts:
drivers/mmc/card/block.c
|
|
This reverts v3.13-rc3+ (78fd82238d0e5716) to v3.12, except for
commits which I noticed which appear relevant to the SDK.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Conflicts:
arch/powerpc/include/asm/kvm_host.h
arch/powerpc/kvm/book3s_hv_rmhandlers.S
arch/powerpc/kvm/book3s_interrupts.S
arch/powerpc/kvm/e500.c
arch/powerpc/kvm/e500mc.c
arch/powerpc/sysdev/fsl_soc.h
drivers/Kconfig
drivers/cpufreq/ppc-corenet-cpufreq.c
drivers/dma/fsldma.c
drivers/dma/s3c24xx-dma.c
drivers/misc/Makefile
drivers/mmc/host/sdhci-of-esdhc.c
drivers/mtd/devices/m25p80.c
drivers/net/ethernet/freescale/gianfar.h
drivers/platform/Kconfig
drivers/platform/Makefile
drivers/spi/spi-fsl-espi.c
include/crypto/algapi.h
include/linux/netdev_features.h
include/linux/skbuff.h
include/net/ip.h
net/core/ethtool.c
|
|
|
|
T1040 FSL SoC has new version of UART controller which
can support 64byte FiFo. Add suuport to enable 64byte FiFO mode
-FCR[EN64] needs to be programmed to 1 to enable it.
-Also, when FCR[EN64]==1, RTL bits to be used as below
to define various Receive Trigger Levels:
-FCR[RTL] = 00 1 byte
-FCR[RTL] = 01 16 bytes
-FCR[RTL] = 10 32 bytes
-FCR[RTL] = 11 56 bytes
-tx_loadsz is set tp 32bytes, As some issues are observed with
64-byte mode which looks to be Si issue.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Change-Id: I0b32f3230bd1c9674a2e85cc4e5a16869dbaa9af
Reviewed-on: http://git.am.freescale.net:8181/10215
Tested-by: Review Code-CDREVIEW <CDREVIEW@freescale.com>
Reviewed-by: Jose Rivera <German.Rivera@freescale.com>
|
|
commit 3685f19e07802ec4207b52465c408f185b66490e upstream.
Tegra chips have 4 or 5 identical UART modules embedded. UARTs C..E have
their MODEM-control signals tied off to a static state. However UARTs A
and B can optionally route those signals to/from package pins, depending
on the exact pinmux configuration.
When these signals are not routed to package pins, false interrupts may
trigger either temporarily, or permanently, all while not showing up in
the IIR; it will read as NO_INT. This will eventually lead to the UART
IRQ being disabled due to unhandled interrupts. When this happens, the
kernel may print e.g.:
irq 68: nobody cared (try booting with the "irqpoll" option)
In order to prevent this, enable UART_BUG_NOMSR. This prevents
UART_IER_MSI from being enabled, which prevents the false interrupts
from triggering.
In practice, this is not needed under any of the following conditions:
* On Tegra chips after Tegra30, since the HW bug has apparently been
fixed.
* On UARTs C..E since their MODEM control signals are tied to the correct
static state which doesn't trigger the issue.
* On UARTs A..B if the MODEM control signals are routed out to package
pins, since they will then carry valid signals.
However, we ignore these exceptions for now, since they are only relevant
if a board actually hooks up more than a 4-wire UART, and no currently
supported board does this. If we ever support a board that does, we can
refine the algorithm that enables UART_BUG_NOMSR to take those exceptions
into account, and/or read a flag from DT/... that indicates that the
board has hooked up and pinmux'd more than a 4-wire UART.
Reported-by: Olof Johansson <olof@lixom.net> # autotester
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9c5320f8d7d9a2cf623e65d50e1113f34d9b9eb1 upstream.
Fix the initialisation of older Quatech serial cards which are fitted with
the AMCC PCI Matchmaker interface chip.
Signed-off-by: Jonathan Woithe (jwoithe@just42.net)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 48c0247d7b7bf58abb85a39021099529df365c4d upstream.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d24c195f90cb1adb178d26d84c722d4b9e551e05 upstream.
Newer Intel PCHs with LPSS have the same Designware controllers than
Haswell but ACPI IDs are different. Add these IDs to the driver list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 9326b047e4fd4a8da72e59d913214a1803e9709c includes a typo
of "8350_core" instead of "8250_core", so correct it.
Fixes kernel bugzilla #60724:
https://bugzilla.kernel.org/show_bug.cgi?id=60724
Reported-by: Christoph Biedl <bugzilla.kernel.bpeb@manchmal.in-ulm.de>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Chip PI7C9X7952/4/8
Signed-off-by: Angelo Butti <buttiangelo@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This adds support for Fintek's 4, 8, and 12 port PCIE serial cards.
Thanks to Fintek for the sample devices, and the spec needed in order to
implement this.
Cc: Amanda Ying <amanda_ying@fintek.com.tw>
Cc: Felix Shih <felix_shih@fintek.com.tw>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add calls to clk_prepare and unprepare so that EMMA Mobile EV2 can
migrate to the common clock framework.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
[takashi.yoshii.ze@renesas.com: edited for conflicts]
Signed-off-by: Takashi Yoshii <takashi.yoshii.zj@renesas.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When configured with UART_16550_COMPATIBLE=NO or in versions prior to
the introduction of this option, the Designware UART will ignore writes
to the LCR if the UART is busy. The current workaround saves a copy of
the last written LCR and re-writes it in the ISR for a special interrupt
that is raised when a write was ignored.
Unfortunately, interrupts are typically disabled prior to performing a
sequence of register writes that include the LCR so the point at which
the retry occurs is too late. An example is serial8250_do_set_termios()
where an ignored LCR write results in the baud divisor not being set and
instead a garbage character is sent out the transmitter.
Furthermore, since serial_port_out() offers no way to indicate failure,
a serious effort must be made to ensure that the LCR is actually updated
before returning back to the caller. This is difficult, however, as a
UART that was busy during the first attempt is likely to still be busy
when a subsequent attempt is made unless some extra action is taken.
This updated workaround reads back the LCR after each write to confirm
that the new value was accepted by the hardware. Should the hardware
ignore a write, the TX/RX FIFOs are cleared and the receive buffer read
before attempting to rewrite the LCR out of the hope that doing so will
force the UART into an idle state. While this may seem unnecessarily
aggressive, writes to the LCR are used to change the baud rate, parity,
stop bit, or data length so the data that may be lost is likely not
important. Admittedly, this is far from ideal but it seems to be the
best that can be done given the hardware limitations.
Lastly, the revised workaround doesn't touch the LCR in the ISR, so it
avoids the possibility of a "serial8250: too much work for irq" lock up.
This problem is rare in real situations but can be reproduced easily by
wiring up two UARTs and running the following commands.
# stty -F /dev/ttyS1 echo
# stty -F /dev/ttyS2 echo
# cat /dev/ttyS1 &
[1] 375
# echo asdf > /dev/ttyS1
asdf
[ 27.700000] serial8250: too much work for irq96
[ 27.700000] serial8250: too much work for irq96
[ 27.710000] serial8250: too much work for irq96
[ 27.710000] serial8250: too much work for irq96
[ 27.720000] serial8250: too much work for irq96
[ 27.720000] serial8250: too much work for irq96
[ 27.730000] serial8250: too much work for irq96
[ 27.730000] serial8250: too much work for irq96
[ 27.740000] serial8250: too much work for irq96
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move the printk() calls to to dev_*() instead, to tie into the dynamic
debugging infrastructure.
Also change some "raw" printk() calls to dev_err() to provide a better
error message to userspace so it can properly identify the device and
not just have to guess.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The stub for dw8250_probe_acpi() is missing an argument.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Intel BayTrail has two HS-UARTs with 64 byte fifo, support
for DMA and support for 16750 compatible Auto Flow Control.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The channel IDs are set to -1 by default. It will prevent
dmaengine from trying to provide the first free channel if
it fails to allocate exclusive channel. This will fix an
issue with ACPI enumerated UARTs that do not support DMA
but still end up getting a DMA channel incorrectly.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It should be available for DT users as well. This does not
enable DMA by default except with ACPI. DT users can enable
DMA based on a property.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
DMA engines usually expect the fifo trigger level to be
aligned with the burst size. It should not be changed even
with small baud rates. This will fix an issue with
Designware DMA engine where the data can not be transferred
over UART with lower baud rates then 2400.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When a serial port is configured for RTS/CTS flow control, serial core
will disable the transmitter if it observes CTS is de-asserted. This is
perfectly reasonable and appropriate when the UART lacks the ability to
automatically perform CTS flow control.
However, if the UART hardware can manage flow control automatically, it
is important that software not get involved. When the DesignWare UART
enables 16C750 style auto-RTS/CTS it stops generating interrupts for
changes in CTS state so software mostly stays out of the way. However,
it does report the true state of CTS in the MSR so software may notice
it is de-asserted and respond by improperly disabling the transmitter.
Once this happens the transmitter will be blocked forever.
To avoid this situation, we simply lie to the 8250 and serial core by
reporting that CTS is asserted whenever auto-RTS/CTS mode is enabled.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix the following sparse warning:
drivers/tty/serial/8250/8250_early.c:196:26: error: incompatible types in comparison expression (different type sizes)
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the tty fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We can't use dev->mod_index for selecting the interrupt routing entry,
because it's not an index into interrupt routing table. It will be even
wrong on a machine with 2 CPUs (4 cores). But all needed information is
contained in the PAT entries for the serial ports. mod[0] contains the
iosapic address and mod_info has some indications for the interrupt
input (at least it looks like it). This patch implements the searching
for the right iosapic and uses this interrupt input information.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: <stable@vger.kernel.org> # 3.10
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
We want the tty fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace kzalloc and clk_get by their managed counterparts to simplify
error and cleanup paths.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The quirks and PCI ID table entries for the original ADDI-DATA APCI-7800
(not the newer APCI-7800-3) use PCI_DEVICE_ID_ADDIDATA_APCI7800 from
<linux/pci_ids.h> but the device ID was actually assigned to ADDI-DATA
by Applied Micro Circuits Corporation (PCI_VENDOR_ID_AMCC). Replace it
locally with #define PCI_DEVICE_ID_AMCC_ADDIDATA_APCI7800.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
PCI_VENDOR_ID_ADDIDATA_OLD has the same value (0x10e8) as
PCI_VENDOR_ID_AMCC in <linux/pci_ids.h>. The vender ID is actually
assigned to Applied Micro Circuits Corporation. The 8250_pci driver
uses PCI_VENDOR_ID_ADDIDATA_OLD in the lists of quirks and PCI IDs for
the ADDI-DATA APCI-7800 card. Change it to use the more accurate
PCI_VENDOR_ID_AMCC.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The recent regression about NetMos 9835 Multi-I/O boards indicates
that comment pointing to the parport_serial driver could be helpful.
Signed-off-by: Stefan Seyfried <seife+kernel@b1-systems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The earlier change to use strlcpy uncovered a bug in the options
argument length calculation causing last character to be truncated.
This makes the actual console to be configured with incorrect
baudrate when specifying the console using console=uart,... syntax.
Bug symptom seen in kernel log output:
Kernel command line: console=uart,mmio,0x90000000,115200
Early serial console at MMIO 0x90000000 (options '11520')
which then results in a invalid baud rate 11520 instead of the
expected 115200 when the console is switched to ttyS0 later
in the boot process.
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull MIPS updates from Ralf Baechle:
"MIPS updates:
- All the things that didn't make 3.10.
- Removes the Windriver PPMC platform. Nobody will miss it.
- Remove a workaround from kernel/irq/irqdomain.c which was there
exclusivly for MIPS. Patch by Grant Likely.
- More small improvments for the SEAD 3 platform
- Improvments on the BMIPS / SMP support for the BCM63xx series.
- Various cleanups of dead leftovers.
- Platform support for the Cavium Octeon-based EdgeRouter Lite.
Two large KVM patchsets didn't make it for this pull request because
their respective authors are vacationing"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
MIPS: SEAD3: Disable L2 cache on SEAD-3.
MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
MIPS: BCM63xx: Add SMP support to prom.c
MIPS: define write{b,w,l,q}_relaxed
MIPS: Expose missing pci_io{map,unmap} declarations
MIPS: Malta: Update GCMP detection.
Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
MIPS: APSP: Remove <asm/kspd.h>
SSB: Kconfig: Amend SSB_EMBEDDED dependencies
MIPS: microMIPS: Fix improper definition of ISA exception bit.
MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
MIPS: Declare emulate_load_store_microMIPS as a static function.
MIPS: Fix typos and cleanup comment
MIPS: Cleanup indentation and whitespace
MIPS: BMIPS: support booting from physical CPU other than 0
MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
MIPS: GIC: Fix gic_set_affinity infinite loop
MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
...
|
|
A few differences needed by OCTEON:
o These are DWC UARTS, but have USR at a different offset.
o Internal SoC buses require reading back from registers to maintain
write ordering.
o 8250 on OCTEON appears with 64-bit wide registers, so when using
readb/writeb in big endian mode we have to adjust the membase to hit
the proper part of the register.
o No UCV register, so we hard code some properties.
Because OCTEON doesn't have a UCV register, I change where
dw8250_setup_port(), which reads the UCV, is called by pushing it in
to the OF and ACPI probe functions, and move unchanged
dw8250_setup_port() earlier in the file.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: linux-mips@linux-mips.org
Cc: Jamie Iles <jamie@jamieiles.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5516/
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
PCI 9835 Multi-I/O Controller"
This reverts commit 8d2f8cd424ca0b99001f3ff4f5db87c4e525f366.
As reported by Stefan, this device already works with the parport_serial
driver, so the 8250_pci driver should not also try to grab it as well.
Reported-by: Stefan Seyfried <stefan.seyfried@googlemail.com>
Cc: Wang YanQing <udknight@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the tty fixes in this branch as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The C8000 workstation (64 bit kernel only) has a somewhat different
serial port configuration than other models.
Thomas Bogendoerfer sent a patch to fix this in September 2010, which
was now minimally modified by me.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
|
