summaryrefslogtreecommitdiff
path: root/drivers/usb/musb
AgeCommit message (Collapse)Author
2010-11-09usb: musb: fail unaligned DMA transfers on v1.8 and aboveAnand Gadiyar
The Inventra DMA engine in version 1.8 and later of the MUSB controller cannot handle DMA addresses that are not aligned to a 4 byte boundary. It ends up ignoring the last two bits programmed in the DMA_ADDR register. This is a deliberate design change in the controller and is documented in the programming guide. Earlier versions of the controller could handle these accesses just fine. Fail dma_channel_program if we see an unaligned address when using the newer controllers, so that the caller can carry out the transfer using PIO mode. (Current callers already have this backup path in place). Signed-off-by: Anand Gadiyar <gadiyar@ti.com> Tested-by: Ming Lei <tom.leiming@gmail.com> Cc: Ajay Kumar Gupta <ajay.gupta@ti.com> Cc: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
2010-11-08usb: musb: gadget: kill duplicate code in musb_gadget_queue()Sergei Shtylyov
musb_gadget_queue() checks for '!req->buf' condition twice: in the second case the code is both duplicated and unreachable as the first check returns early. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2010-11-05usb: musb: Fix handling of spurious SESSREQHeikki Krogerus
Rely on VBUS being valid on top off B device. Signed-off-by: Heikki Krogerus <heikki.krogerus@nokia.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2010-11-05usb: musb: fix kernel oops when loading musb_hdrc module for the 2nd timeMing Lei
musb driver still may write MUSB_DEVCTL register after clock is disabled in musb_platform_exit, which may cause the kernel oops[1] when musb_hdrc module is loaded for the 2nd time. The patch fixes the kernel oops in this case. [1] kernel oops when loading musb_hdrc module for the 2nd time [ 93.380279] musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=5 [ 93.387847] bus: 'platform': add driver musb_hdrc [ 93.388153] bus: 'platform': driver_probe_device: matched device musb_hdrc with driver musb_hdrc [ 93.388183] bus: 'platform': really_probe: probing driver musb_hdrc with device musb_hdrc [ 93.405090] HS USB OTG: revision 0x33, sysconfig 0x2010, sysstatus 0x1, intrfsel 0x1, simenable 0x0 [ 93.405364] musb_hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) [ 93.405395] musb_hdrc: MHDRC RTL version 1.400 [ 93.405426] musb_hdrc: setup fifo_mode 3 [ 93.405456] musb_hdrc: 7/31 max ep, 3648/16384 memory [ 93.405487] musb_core_init 1524: musb_hdrc: hw_ep 0shared, max 64 [ 93.405487] musb_core_init 1524: musb_hdrc: hw_ep 1tx, doublebuffer, max 512 [ 93.405517] musb_core_init 1533: musb_hdrc: hw_ep 1rx, doublebuffer, max 512 [ 93.405548] musb_core_init 1524: musb_hdrc: hw_ep 2tx, max 512 [ 93.405578] musb_core_init 1533: musb_hdrc: hw_ep 2rx, max 512 [ 93.405578] musb_core_init 1524: musb_hdrc: hw_ep 3shared, max 256 [ 93.405609] musb_core_init 1524: musb_hdrc: hw_ep 4shared, max 256 [ 93.405853] musb_platform_try_idle 133: b_idle inactive, for idle timer for 7 ms [ 93.405944] device: 'gadget': device_add [ 93.406921] PM: Adding info for No Bus:gadget [ 93.406951] musb_init_controller 2136: OTG mode, status 0, dev80 [ 93.407379] musb_do_idle 51: musb_do_idle: state=1 [ 93.408233] musb_hdrc musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92 [ 93.416656] driver: 'musb_hdrc': driver_bound: bound to device 'musb_hdrc' [ 93.416687] bus: 'platform': really_probe: bound device musb_hdrc to driver musb_hdrc [ 124.486938] bus: 'platform': remove driver musb_hdrc [ 124.490509] twl4030_usb twl4030_usb: twl4030_phy_suspend [ 124.491424] device: 'gadget': device_unregister [ 124.491424] PM: Removing info for No Bus:gadget [ 124.495269] gadget: musb_gadget_release [ 124.498992] driver: 'musb_hdrc': driver_release [ 129.569366] musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=5 [ 129.576934] bus: 'platform': add driver musb_hdrc [ 129.577209] bus: 'platform': driver_probe_device: matched device musb_hdrc with driver musb_hdrc [ 129.577239] bus: 'platform': really_probe: probing driver musb_hdrc with device musb_hdrc [ 129.592651] twl4030_usb twl4030_usb: twl4030_phy_resume [ 129.592681] Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa0ab404 [ 129.600830] Internal error: : 1028 [#1] [ 129.604858] last sysfs file: /sys/devices/platform/i2c_omap.3/i2c-3/i2c-dev/i2c-3/dev [ 129.613067] Modules linked in: musb_hdrc(+) [last unloaded: musb_hdrc] [ 129.619964] CPU: 0 Not tainted (2.6.36-next-20101021+ #372) [ 129.626281] PC is at musb_platform_init+0xb0/0x1c8 [musb_hdrc] [ 129.632415] LR is at mark_held_locks+0x64/0x94 [ 129.637084] pc : [<bf032198>] lr : [<c00ad7c4>] psr: 20000013 [ 129.637084] sp : c6d5fcb0 ip : c6d5fc38 fp : c6d5fcd4 [ 129.649139] r10: c6e72180 r9 : fa0ab000 r8 : c05612e8 [ 129.654602] r7 : 0000005c r6 : c0559cc8 r5 : c6e72180 r4 : c0561548 [ 129.661468] r3 : 04d60047 r2 : fa0ab000 r1 : c07169d8 r0 : 00000000 [ 129.668304] Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user [ 129.675811] Control: 10c5387d Table: 86e4c019 DAC: 00000015 [ 129.681823] Process insmod (pid: 554, stack limit = 0xc6d5e2f0) [ 129.688049] Stack: (0xc6d5fcb0 to 0xc6d60000) [ 129.692626] fca0: fa0ab000 c0555c54 c6d5fcd4 c0561548 [ 129.701202] fcc0: 00000003 c05612e0 c6d5fe04 c6d5fcd8 bf03140c bf0320f4 c6d5fd9c c6d5fce8 [ 129.709808] fce0: c015cb94 c041448c c06d9d10 ffffffff c6d5fd14 c6d5fd00 c00adbec c6d5fd40 [ 129.718383] fd00: c015d478 c6d5fdb0 c6d5fd24 c00a9d18 c6d5e000 60000013 bf02a4ac c05612bc [ 129.726989] fd20: c0414fb4 c00a9cf0 c6d5fd54 c6d5fd38 c015bbdc c0244280 c6e8b7b0 c7929330 [ 129.735565] fd40: c6d5fdb0 c6d5fdb0 c6d5fd7c c6e7227c c015c010 c015bb90 c015c2ac c6d5fdb0 [ 129.744171] fd60: c7929330 c6d5fdb0 c7929330 c6e8b7b0 c6d5fd9c 00000000 c7929330 c6e8b7b0 [ 129.752746] fd80: c6d5fdb0 00000000 00000001 00000000 c6d5fde4 c6d5fda0 c015d478 c015cb74 [ 129.761322] fda0: c056138c 00000000 c6d5fdcc c6d5fdb8 c7929330 00000000 c056138c c05612e8 [ 129.769927] fdc0: 00000000 c05612f0 c0c5d62c c06f6e00 c73217c0 00000000 c6d5fdf4 c05612e8 [ 129.778503] fde0: c05612e8 bf02a2e4 c0c5d62c c06f6e00 c73217c0 00000000 c6d5fe14 c6d5fe08 [ 129.787109] fe00: c029a398 bf0311c8 c6d5fe4c c6d5fe18 c0299120 c029a384 c7919140 22222222 [ 129.795684] fe20: c6d5fe4c c05612e8 c056131c bf02a2e4 c0299278 c06f6e00 c73217c0 00000000 [ 129.804290] fe40: c6d5fe6c c6d5fe50 c0299314 c0299020 00000000 c6d5fe70 bf02a2e4 c0299278 [ 129.812866] fe60: c6d5fe94 c6d5fe70 c02987d4 c0299284 c7825060 c78c6618 00000000 bf02a2e4 [ 129.821441] fe80: c06e4c98 00000000 c6d5fea4 c6d5fe98 c0298ea4 c0298778 c6d5fedc c6d5fea8 [ 129.830047] fea0: c0297f84 c0298e8c bf02716c 000b9008 bf02a2e4 bf02a2d0 000b9008 bf02a2e4 [ 129.838623] fec0: 00000000 c06f6e00 bf031000 00000000 c6d5fefc c6d5fee0 c0299614 c0297ec0 [ 129.847229] fee0: bf02a2d0 000b9008 bf02a388 00000000 c6d5ff0c c6d5ff00 c029a868 c02995a8 [ 129.855804] ff00: c6d5ff24 c6d5ff10 c029a88c c029a818 0010281c 000b9008 c6d5ff34 c6d5ff28 [ 129.864410] ff20: bf03104c c029a878 c6d5ff7c c6d5ff38 c00463dc bf03100c 00000000 00000000 [ 129.872985] ff40: 00000000 0010281c 000b9008 bf02a388 00000000 0010281c 000b9008 bf02a388 [ 129.881591] ff60: 00000000 c00521c8 c6d5e000 00000000 c6d5ffa4 c6d5ff80 c00bb9b8 c00463ac [ 129.890167] ff80: c00adc88 c00ada68 00097e8e bebbfcf4 0010281c 00000080 00000000 c6d5ffa8 [ 129.898742] ffa0: c0052000 c00bb908 00097e8e bebbfcf4 402c9008 0010281c 000b9008 bebbfe5a [ 129.907348] ffc0: 00097e8e bebbfcf4 0010281c 00000080 00000014 bebbfcf4 bebbfe06 0000005b [ 129.915924] ffe0: bebbf9a0 bebbf990 0001a108 40263ec0 60000010 402c9008 011b0000 0000007c [ 129.924499] Backtrace: [ 129.927185] [<bf0320e8>] (musb_platform_init+0x0/0x1c8 [musb_hdrc]) from [<bf03140c>] (musb_probe+0x250/0xf2c [musb_hdrc]) [ 129.938781] r6:c05612e0 r5:00000003 r4:c0561548 [ 129.943695] [<bf0311bc>] (musb_probe+0x0/0xf2c [musb_hdrc]) from [<c029a398>] (platform_drv_probe+0x20/0x24) [ 129.954040] [<c029a378>] (platform_drv_probe+0x0/0x24) from [<c0299120>] (driver_probe_device+0x10c/0x264) [ 129.964172] [<c0299014>] (driver_probe_device+0x0/0x264) from [<c0299314>] (__driver_attach+0x9c/0xa0) [ 129.973968] [<c0299278>] (__driver_attach+0x0/0xa0) from [<c02987d4>] (bus_for_each_dev+0x68/0x94) [ 129.983367] r7:c0299278 r6:bf02a2e4 r5:c6d5fe70 r4:00000000 [ 129.989349] [<c029876c>] (bus_for_each_dev+0x0/0x94) from [<c0298ea4>] (driver_attach+0x24/0x28) [ 129.998565] r7:00000000 r6:c06e4c98 r5:bf02a2e4 r4:00000000 [ 130.004547] [<c0298e80>] (driver_attach+0x0/0x28) from [<c0297f84>] (bus_add_driver+0xd0/0x274) [ 130.013671] [<c0297eb4>] (bus_add_driver+0x0/0x274) from [<c0299614>] (driver_register+0x78/0x158) [ 130.023101] [<c029959c>] (driver_register+0x0/0x158) from [<c029a868>] (platform_driver_register+0x5c/0x60) [ 130.033325] r7:00000000 r6:bf02a388 r5:000b9008 r4:bf02a2d0 [ 130.039276] [<c029a80c>] (platform_driver_register+0x0/0x60) from [<c029a88c>] (platform_driver_probe+0x20/0xa8) [ 130.050018] [<c029a86c>] (platform_driver_probe+0x0/0xa8) from [<bf03104c>] (musb_init+0x4c/0x54 [musb_hdrc]) [ 130.060424] r5:000b9008 r4:0010281c [ 130.064239] [<bf031000>] (musb_init+0x0/0x54 [musb_hdrc]) from [<c00463dc>] (do_one_initcall+0x3c/0x1c0) [ 130.074218] [<c00463a0>] (do_one_initcall+0x0/0x1c0) from [<c00bb9b8>] (sys_init_module+0xbc/0x1d0) [ 130.083709] [<c00bb8fc>] (sys_init_module+0x0/0x1d0) from [<c0052000>] (ret_fast_syscall+0x0/0x3c) [ 130.093109] r7:00000080 r6:0010281c r5:bebbfcf4 r4:00097e8e [ 130.099090] Code: 0a000046 e3a01001 e12fff33 e59520e4 (e5923404) [ 130.105621] ---[ end trace 1d0bd69deb79164d ]--- Cc: Ajay Kumar Gupta <ajay.gupta@ti.com> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Anand Gadiyar <gadiyar@ti.com> Cc: stable@kernel.org Signed-off-by: Ming Lei <tom.leiming@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2010-11-05USB: musb: blackfin: push clkin value to platform resourcesBob Liu
In order to not touch the driver file for different xtal usage, push the clkin value to board file and calculate the register value instead of hardcoding it. Signed-off-by: Bob Liu <lliubbo@gmail.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
2010-11-05USB: musb: blackfin: fix dynamic device<->host changingBob Liu
We need to restart the timer in order to recognize USB devices in host-only mode. Signed-off-by: Bob Liu <lliubbo@gmail.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
2010-11-05USB: musb: blackfin: pm: make it workBob Liu
Split the USB MMR init steps out into a helper func that both the platform init and the resume code may call. Then while suspending, the gpio_vrsel will change from high to low which will generate a wakeup event and resume the system immediately, so we need to manually drive it low before we sleep. Signed-off-by: Bob Liu <lliubbo@gmail.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
2010-11-05USB: musb: pm: don't rely fully on clock supportBob Liu
Since clock support is optional across processors, don't make the whole musb pm paths depend upon it. Just conditionalize the clock accesses. Signed-off-by: Bob Liu <lliubbo@gmail.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
2010-11-05USB: musb: blackfin: fix musb_read_txhubport() definitionIan Jeffray
The new MUSB power code needs musb_read_txhubport() to return a value (so stub it as 0 like the other Blackfin hub funcs). Signed-off-by: Ian Jeffray <ian@jeffray.co.uk> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
2010-11-05USB: musb: gadget: fix MUSB_TXMAXP and MUSB_RXMAXP configurationMing Lei
Commit 9f445cb29918dc488b7a9a92ef018599cce33df7[USB: musb: disable double buffering for older RTL versions] tries to disable double buffer mode by writing endpoint hw max packet size to TXMAP/RXMAP. First the approach can break full speed and cause overflow problems. We should always set those registers with the actual max packet size from endpoint descriptor. Second, the problem describe by commit 9f445cb29918dc488b7a9a92ef018599cce33df7 was caused by musb gadget driver; nothing to do with RTL revision as originaly suspected. The real fix to the problem is to always use actual max packet size from endpoint descriptor to config TXMAP/RXMAP registers. Cc: Cliff Cai <cliff.cai@analog.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Anand Gadiyar <gadiyar@ti.com> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: stable@kernel.org Signed-off-by: Ming Lei <tom.leiming@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2010-11-05usb: musb: don't leave PHY enabled on shutdown()Grazvydas Ignotas
Some actions like musb_platform_exit are only performed on module removal and not on shutdown, which results in PHY being left enabled on reboot at least. This is sometimes causing strange failures after reboot (observed on OMAP3 pandora board), when DEVCTL does not report VBUS state correctly due to unknown reasons (possibly because of communication issues between musb IP and PHY). Running musb_platform_exit before reset seems to resolve that issue. Move some exit code from musb_remove() to musb_shutdown() so that it is performed on both module removal and shutdown/reset. Also convert the host check so that it doesn't need #ifdef. Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2010-11-05usb: musb: musb_gadget: fix resource leakage in error pathRahul Ruikar
In function musb_gadget_setup() call put_device() when device_register() fails. Signed-off-by: Rahul Ruikar <rahul.ruikar@gmail.com> Acked-by: Ming Lei <tom.leiming@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2010-11-05usb: musb: gadget: fix dma mode 0 in double buffer Rx caseMing Lei
1, In Rx double buffer case, FIFO may have two packets, so rxstate should be called to unload fifo if RXPKTRDY is set even the current request has not been completed. 2, Commit 633ba7876b96ec339ef685357e2f7c60b5a8ce85 introduces autoclear to support double buffer in dma mode 0, so remove clearing RXPKTRDY manually for dma mode 0. 3, Commit c7af6b29ffeffbeb28caf39e5b2ce29b11807c7d may break dma mode 1 for non-doublebuffer endpoint, fix it. With this patch, either usbtest #5 or g_file_storage(writing file to device in usb host) or g_ether have been tested OK in double buffer case(using fifo mode 3). Also, this patch has been verified that single buffer case can't be broken. Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Anand Gadiyar <gadiyar@ti.com> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Ming Lei <tom.leiming@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2010-10-22USB: musb: AM35x: Workaround for fifo read issueAjay Kumar Gupta
AM35x supports only 32bit read operations so we need to have workaround for 8bit and 16bit read operations. Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-22USB: musb: add musb support for AM35xAjay Kumar Gupta
AM35x has musb interface and uses CPPI4.1 DMA engine. Current patch supports only PIO mode. DMA support can be added later once basic CPPI4.1 DMA patch is accepted. Also added USB_MUSB_AM35X which is required to differentiate musb ips between OMAP3x and AM35x. This config would be used to for below purposes, - Select am35x.c instead of omap2430.c for compilation at drivers/usb/musb directory. Please note there are significant differneces in these two files as musb ip in quite different on AM35x. Please note that in multi omap configuration only omap2430.c file will get compiled and we would require to select only AM35x based board config to compile am35x.c - Select workaround codes applicable for AM35x musb issues. one such workaround is for bytewise read issue on AM35x. Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-22usb: makefile cleanupmatt mooney
For all modules, change <module>-objs to <module>-y; remove if-statements and replace with lists using the kbuild idiom; move flags to the top of the file; and fix alignment while trying to maintain the original scheme in each file. None of the dependencies are modified. Signed-off-by: matt mooney <mfm@muteddisk.com> Acked-by: Sam Ravnborg <sam@ravnborg.org> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-22usb: musb: blackfin: call gpio_free() on error path in musb_platform_init()Sergei Shtylyov
Blackfin's musb_platform_init() needs to call gpio_free() for error cleanup iff otg_get_transceiver() call returns NULL. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Acked-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Felipe Balbi <balbi@ti.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-22usb: musb: blackfin: call usb_nop_xceiv_unregister() in musb_platform_exit()Sergei Shtylyov
Blackfin's musb_platform_exit() forgets to call usb_nop_xceiv_unregister(). While fixing this, also remove the unneeded blank line there. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Acked-by: Mike Frysinger <vapier@gentoo.org> Cc: stable <stable@kernel.org> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-22USB: MUSB: fix kernel WARNING/oops when unloading module in OTG modeSergei Shtylyov
Since commit 461972d8a4c94bc44f11a13046041c78a7cf18dd (musb_core: don't call musb_platform_exit() twice), unloading the driver module results in a WARNING "kobject: '(null)' (c73de788): is not initialized, yet kobject_put() is being called." (or even kernel oops) on e.g. DaVincis, though only in the OTG mode. There exists dubious and unbalanced put_device() call in musb_free() which takes place only in the OTG mode. As this commit caused musb_platform_exit() to be called (and so unregister the NOP transceiver) before this put_device() call, this function references already freed memory. On the other hand, all the glue layers miss the otg_put_transceiver() call, complementary to the otg_get_transceiver() call that they do. So, I think the solution is to get rid of the strange put_device() call, and instead call otg_put_transceiver() in the glue layers... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: stable <stable@kernel.org> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-22usb: change to new flag variablematt mooney
Replace EXTRA_CFLAGS with ccflags-y. Signed-off-by: matt mooney <mfm@muteddisk.com> Acked-by: WANG Cong <xiyou.wangcong@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-22usb: musb: gadget: only enable AUTOCLEAR in double buffered caseFelipe Balbi
commit 633ba7876b96ec339ef685357e2f7c60b5a8ce85 broke g_file_storage functionality by enabling AUTOCLEAR on all cases without caring for all gadget drivers. This patch will only enable AUTOCLEAR if our endpoint's FIFO was configured with double buffering support. Note this is not a complete fix, double buffered case still doesn't work always, but that hasn't been working for quite some time. Other than reverting the entire commit and breaking testusb with double buffered case again, I decided it was better to fix the single buffered case and spend more time fixing double buffered case properly. Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-22usb: musb: gadget: fix ZLP sending in musb_g_tx(v1)Ming Lei
This patch fixes the problem reported by Sergei: >how come? we need to send ZLP before giving back the request. >Well, look at the code ionce again. We need to send ZLP *after* >request->actual == request->length, but as the check is inserted >after the ZLP send, ZLP *may* be sent once the first DMA completes, >not the last. The patch also has been discussed on the link below: http://marc.info/?t=128454814900001&r=1&w=2 Signed-off-by: Ming Lei <tom.leiming@gmail.com> Reported-by: Sergei Shtylyov <sshtylyov@mvista.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Anand Gadiyar <gadiyar@ti.com> Cc: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-22usb: musb: ignore spurious SESSREQ interruptsHeikki Krogerus
This will ignore any SESSREQ interrupt if musb is B state. Charger detection may cause spurious SESSREQ interrupts. Signed-off-by: Heikki Krogerus <ext-heikki.krogerus@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-22usb: musb: gadget: kill unreachable code in musb_g_rx()Sergei Shtylyov
musb_g_rx() always returns if next_request() call yields NULL, so the DBG() near the function's end can never be invoked. Remove it along with unneeded 'return'; also remove the duplicate 'request' check... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-22USB: musb: suppress warning about unused flagsJon Povey
Wrap flags with uninitialized_var() to suppress this: drivers/usb/musb/cppi_dma.c:1158: warning: 'flags' may be used uninitialized in this function Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-22usb: musb: host: support DMA transfers greater than max channel lengthT. S., Anil Kumar
Add support for MUSB Host DMA transfers greater than max channel length, so that such transfers won't be truncated. Signed-off-by: Anil Shetty <anil@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-22usb: musb: Change to direct addr in context save/restoreBob Liu
Since not all platforms are using the same offset 0x10 in musb_save/restore_context() eg Blackfin the offset is 0x40, Change the indexed address to direct. Signed-off-by: Bob Liu <lliubbo@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-22usb: musb: host: unmap the buffer for PIO data transfersMaulik Mankad
The USB stack maps the buffer for DMA if the controller supports DMA. MUSB controller can perform DMA as well as PIO transfers. The buffer needs to be unmapped before CPU can perform PIO data transfers. Export unmap_urb_for_dma() so that drivers can perform the DMA unmapping in a sane way. Signed-off-by: Maulik Mankad <x0082077@ti.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-22usb: musb: musbhsdma: increase max_len to 1MBAnil Shetty
MUSB's DMA controller max channel length was set to 64k. Transfer length greater than this max value is being truncated. Signed-off-by: Anil Shetty <anil@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-22usb: musb: support ISO high bandwidth for gadget modeMing Lei
This patch has been tested OK on beagle B5 board and use usbtest #15 and #16 as testcase. Signed-off-by: Ming Lei <tom.leiming@gmail.com> Reviewed-by: Sergei Shtylyov <sshtylyov@mvista.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Anand Gadiyar <gadiyar@ti.com> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-22usb: musb: introduce DA8xx/OMAP-L1x glue layerSergei Shtylyov
Texas Instruments DA8xx/OMAP-L1x glue layer for the MUSBMHRDC driver. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Yadviga Grigorieva <yadviga@ru.mvista.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-22USB: musb: make DBG() calls actually depend on CONFIG_USB_MUSB_DEBUGSergei Shtylyov
Enabling CONFIG_USB_MUSB_DEBUG option causes -DDEBUG to be added to gcc's command line, however the DBG() macro doesn't depend on DEBUG, so that the debugging messages get printed regardless of the option, and I don't think that this was intended. Get rid of otherwise unused xprintk() macro and make DBG() macro directly call pr_debug() which only results in the actual code generated if DEBUG is defined. This change makes musb_hdrc.o ~30% less in size with CONFIG_USB_MUSB_DEBUG disabled (in host mode). Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-22usb gadget: don't save bind callback in struct usb_gadget_driverUwe Kleine-König
To accomplish this the function to register a gadget driver takes the bind function as a second argument. To make things clearer rename the function to resemble platform_driver_probe. This fixes many section mismatches like WARNING: drivers/usb/gadget/g_printer.o(.data+0xc): Section mismatch in reference from the variable printer_driver to the function .init.text:printer_bind() The variable printer_driver references the function __init printer_bind() All callers are fixed. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> [m.nazarewicz@samsung.com: added dbgp] Signed-off-by: Michał Nazarewicz <m.nazarewicz@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-24usb: musb: gadget: restart request on clearing endpoint haltSergei Shtylyov
Commit 46034dca515bc4ddca0399ae58106d1f5f0d809f (USB: musb_gadget_ep0: stop abusing musb_gadget_set_halt()) forgot to restart a queued request after clearing the endpoint halt feature. This results in a couple of USB resets while enumerating the file-backed storage gadget due to CSW packet not being sent for the MODE SENSE(10) command. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: stable@kernel.org Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-24usb: musb: host: Issue a memory barrier before starting DMASantosh Shilimkar
This patch fixes the issue which was observed while transfering a large file ( > 20MB) over USB (OMAP MUSB controller acts as USB host) to an attached USB thumb drive. It was found that CDB field of CBW packet was set to 0x0. This was due to missing a barrier before DMA engine starts transfer. This buffer is allocated using dma_alloc_coherent which gives non-cacheble but bufferable memory and hence needed a write memory barrier to flush the write buffer. More info on this thread is here: http://www.spinics.net/lists/linux-omap/msg33987.html Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Maulik Mankad <x0082077@ti.com> Cc: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-24usb: musb: gadget: fix dma length in txstateMing Lei
DMA length should not go beyond the availabe space of request buffer, so fix it. Also set max_len of cppi dma channel as max size of int type, so make musb dma handling happier. Signed-off-by: Ming Lei <tom.leiming@gmail.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Anand Gadiyar <gadiyar@ti.com> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-24usb: musb: gadget: complete request only if data is transfered overMing Lei
Complete the current request only if the data transfer is over. Signed-off-by: Ming Lei <tom.leiming@gmail.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Anand Gadiyar <gadiyar@ti.com> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-24usb: musb: gadget: fix DMA length for OUT transferMing Lei
DMA length should not go beyond the availabe space of request buffer, so fix it. Signed-off-by: Ming Lei <tom.leiming@gmail.com> Acked-by: Anand Gadiyar <gadiyar@ti.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Anand Gadiyar <gadiyar@ti.com> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-24usb: musb: gadget: enable autoclear for OUT transfer in both DMA 0 and DMA 1Ming Lei
This patch fixes one bugs of OUT transfer in double buffer case: -the current code only enable autoclear for dma mode 1, and not for dma mode 0 Without this patch, test #5 of usbtest can't be passed if we configure musb as g_zero and use fifo mode 3 to enable double buffer mode. With this patch and the following patch(fix dma length), on my beagle B5, test#5(queued bulk out) may go beyond 18Mbyte/s(seems dma mode 0 is quicker in double buffer case) if musb is configured as g_zero and fifo mode 3 is taken, follows the test command: #./testusb -D DEV_NAME -c 1024 -t 5 -s 32768 -g 8 [1] Also I have tested this patch can't make g_ether broken. [1],source of testusb : tools/usb/testusb.c under linux kernel; Signed-off-by: Ming Lei <tom.leiming@gmail.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Anand Gadiyar <gadiyar@ti.com> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-24usb: musb: gadget: fix bulk IN infinit hangs in double buffer caseMing Lei
This patch fixes one infinite hang of bulk IN transfer in double buffer case, the hang can be observed easily by test #6 of usbtest if musb is configured as g_zero and fifo mode 3 is taken to enable double fifo. In fact, the patch only removes the check for non-empty fifo before loading data from new request into fifo since the check is not correct: -in double buffer case, fifo may accommodate more than one packet, even though it has contained one packet already and is non-empty -since last DMA is completed before calling musb_g_tx, it is sure that fifo may accommodate at least one packet Without applying the patch, new requst enqueued from .complte may not have a chance to be loaded into fifo, then will never be completed and cause infinite hangs. With the patch, on my beagle B5, test#6(queued bulk in) can be passed and test result may go beyond 33Mbyte/s if musb is configured as g_zero and fifo mode 3 is taken, follows the test command: #testusb -D DEV_NAME -c 1024 -t 6 -s 32768 -g 8 [1] [1], -source of testusb : tools/usb/testusb.c under linux kernel; Signed-off-by: Ming Lei <tom.leiming@gmail.com> Acked-by: Anand Gadiyar <gadiyar@ti.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Anand Gadiyar <gadiyar@ti.com> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-24usb: musb: gadget: fix kernel panic if using out ep with FIFO_TXRX styleMing Lei
For shared fifo hw endpoint(with FIFO_TXRX style), only ep_in field of musb_hw_ep is intialized in musb_g_init_endpoints, and ep_out is not initialized, but musb_g_rx and rxstate may access ep_out field of musb_hw_ep by the method below: musb_ep = &musb->endpoints[epnum].ep_out which can cause the kernel panic[1] below, this patch fixes the issue by getting 'musb_ep' from '&musb->endpoints[epnum].ep_in' for shared fifo endpoint. [1], kernel panic [root@OMAP3EVM /]# musb_interrupt 1583: ** IRQ peripheral usb0008 tx0000 rx4000 musb_stage0_irq 460: <== Power=f0, DevCtl=99, int_usb=0x8 musb_g_rx 772: <== (null), rxcsr 4007 ffffffe8 musb_g_rx 786: iso overrun on ffffffe8 Unable to handle kernel NULL pointer dereference at virtual address 00000008 pgd = c0004000 [00000008] *pgd=00000000 Internal error: Oops: 17 [#1] PREEMPT last sysfs file: /sys/devices/platform/musb_hdrc/usb1/usb_device/usbdev1.1/dev Modules linked in: g_zero CPU: 0 Tainted: G W (2.6.35-rc6-gkh-wl+ #92) PC is at musb_g_rx+0xfc/0x2ec LR is at vprintk+0x3f4/0x458 pc : [<c02c07a4>] lr : [<c006ccb0>] psr: 20000193 sp : c760bd78 ip : c03c9d70 fp : c760bdbc r10: 00000000 r9 : fa0ab1e0 r8 : 0000000e r7 : c7e80158 r6 : ffffffe8 r5 : 00000001 r4 : 00004003 r3 : 00010003 r2 : c760bcd8 r1 : c03cd030 r0 : 0000002e Flags: nzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel Control: 10c5387d Table: 8778c019 DAC: 00000017 Process kmemleak (pid: 421, stack limit = 0xc760a2e8) Stack: (0xc760bd78 to 0xc760c000) bd60: ffffffe8 c04b1b58 bd80: ffffffe8 c7c01ac0 00000000 c7e80d24 c0084238 00000001 00000001 c7e80158 bda0: 0000000e 00000008 00000099 000000f0 c760be04 c760bdc0 c02bcd68 c02c06b4 bdc0: 00000099 00000008 00004000 c760bdd8 c03cc4f8 00000000 00000002 c7e80158 bde0: c7d2e300 60000193 c760a000 0000005c 00000000 00000000 c760be24 c760be08 be00: c02bcecc c02bc1ac c7d2e300 c7d2e300 0000005c c760a000 c760be54 c760be28 be20: c00ad698 c02bce6c 00000000 c7d2e300 c067c258 0000005c c067c294 00000001 be40: c760a000 00000000 c760be74 c760be58 c00af984 c00ad5fc 0000005c 00000000 be60: 00000000 00000002 c760be8c c760be78 c0039080 c00af8d0 ffffffff fa200000 be80: c760beec c760be90 c0039b6c c003900c 00000001 00000000 c7d1e240 00000000 bea0: 00000000 c068bae8 00000000 60000013 00000001 00000000 00000000 c760beec bec0: c0064ecc c760bed8 c00ff7d0 c003a0a8 60000013 ffffffff 00000000 c068bae8 bee0: c760bf24 c760bef0 c00ff7d0 c0064ec4 00000001 00000000 c00ff700 00000000 bf00: c0087f00 00000000 60000013 c0d76a70 c0e23795 00000001 c760bf4c c760bf28 bf20: c00ffdd8 c00ff70c c068bb08 c068bae8 60000013 c0100938 c068bb30 00000000 bf40: c760bf84 c760bf50 c010014c c00ffd84 00000001 00000000 c010000c 00012c00 bf60: c7c33f04 00012c00 c7c33f04 00000000 c0100938 00000000 c760bf9c c760bf88 bf80: c01009a8 c0100018 c760bfa8 c7c33f04 c760bff4 c760bfa0 c0088000 c0100944 bfa0: c760bf98 00000000 00000000 00000001 dead4ead ffffffff ffffffff c08ba2bc bfc0: 00000000 c049e7fa 00000000 c0087f70 c760bfd0 c760bfd0 c7c33f04 c0087f70 bfe0: c006f5e8 00000013 00000000 c760bff8 c006f5e8 c0087f7c 7f0004ff df2000ff Backtrace: [<c02c06a8>] (musb_g_rx+0x0/0x2ec) from [<c02bcd68>] (musb_interrupt+0xbc8/0xcc0) [<c02bc1a0>] (musb_interrupt+0x0/0xcc0) from [<c02bcecc>] (generic_interrupt+0x6c/0x84) [<c02bce60>] (generic_interrupt+0x0/0x84) from [<c00ad698>] (handle_IRQ_event+0xa8/0x1ec) r7:c760a000 r6:0000005c r5:c7d2e300 r4:c7d2e300 [<c00ad5f0>] (handle_IRQ_event+0x0/0x1ec) from [<c00af984>] (handle_level_irq+0xc0/0x13c) [<c00af8c4>] (handle_level_irq+0x0/0x13c) from [<c0039080>] (asm_do_IRQ+0x80/0xa0) r7:00000002 r6:00000000 r5:00000000 r4:0000005c [<c0039000>] (asm_do_IRQ+0x0/0xa0) from [<c0039b6c>] (__irq_svc+0x4c/0xb4) Exception stack(0xc760be90 to 0xc760bed8) be80: 00000001 00000000 c7d1e240 00000000 bea0: 00000000 c068bae8 00000000 60000013 00000001 00000000 00000000 c760beec bec0: c0064ecc c760bed8 c00ff7d0 c003a0a8 60000013 ffffffff r5:fa200000 r4:ffffffff [<c0064eb8>] (sub_preempt_count+0x0/0x100) from [<c00ff7d0>] (find_and_get_object+0xd0/0x110) r5:c068bae8 r4:00000000 [<c00ff700>] (find_and_get_object+0x0/0x110) from [<c00ffdd8>] (scan_block+0x60/0x104) r8:00000001 r7:c0e23795 r6:c0d76a70 r5:60000013 r4:00000000 [<c00ffd78>] (scan_block+0x0/0x104) from [<c010014c>] (kmemleak_scan+0x140/0x484) [<c010000c>] (kmemleak_scan+0x0/0x484) from [<c01009a8>] (kmemleak_scan_thread+0x70/0xcc) r8:00000000 r7:c0100938 r6:00000000 r5:c7c33f04 r4:00012c00 [<c0100938>] (kmemleak_scan_thread+0x0/0xcc) from [<c0088000>] (kthread+0x90/0x98) r5:c7c33f04 r4:c760bfa8 [<c0087f70>] (kthread+0x0/0x98) from [<c006f5e8>] (do_exit+0x0/0x684) r7:00000013 r6:c006f5e8 r5:c0087f70 r4:c7c33f04 Code: e3002312 e58d6000 e2833e16 eb0422d5 (e5963020) ---[ end trace f3d5e96f75c297b7 ]--- Signed-off-by: Ming Lei <tom.leiming@gmail.com> Reviewed-by: Sergei Shtylyov <sshtylyov@mvista.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Anand Gadiyar <gadiyar@ti.com> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: stable <stable@kernel.org> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-09-20usb: musb_debugfs: don't use the struct file private_data field with seq_filesMathias Nyman
seq_files use the private_data field of a file struct for storing a seq_file structure, data should be stored in seq_file's own private field (e.g. file->private_data->private) Otherwise seq_release() will free the private data when the file is closed. Signed-off-by: Mathias Nyman <mathias.nyman@nokia.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-08-10USB: musb: forward debug mode feature to gadgetstephane duverger
This is a patch for the musb usb controller. It allows forwarding of the debug mode feature to its gadget in order to be able to act as an ehci debug device. This patch has been tested on an IGEPv2 board running a 2.6.35-rc1 kernel. Signed-off-by: Stephane Duverger <stephane.duverger@gmail.com> Cc: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-08-10USB: musb: do not override DMA mode in channel programAnand Gadiyar
There is no reason for the DMA channel program to override the DMA mode passed down by its caller. Use the passed parameter directly, and let the caller handle the decision on which mode is to be used. Signed-off-by: Anand Gadiyar <gadiyar@ti.com> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-08-10USB: musb: Kill board specific pinmux from driver fileAnand Gadiyar
This pin-muxing is best done in the board files. The driver should not do this explicitly. Also, this code causes a warning to be thrown when OMAP2430 and OMAP3/4 support are enabled in the same kernel. Signed-off-by: Anand Gadiyar <gadiyar@ti.com> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-08-10USB: musb: fix compilation warning in host only modeAjay Kumar Gupta
Fixes below compilation warning when host only configuration is selected. drivers/usb/musb/musb_core.c: In function 'musb_stage0_irq': drivers/usb/musb/musb_core.c:711: warning: unused variable 'mbase' Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-08-10USB: musb: use correct register widths in register dumpsAnand Gadiyar
DMA_ADDR and DMA_COUNT are 32-bit registers, not 16-bit. Marking them as 16-bit in the table causes only the lower 16-bits to be dumped and this is misleading. Signed-off-by: Anand Gadiyar <gadiyar@ti.com> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-08-10USB: convert usb_hcd bitfields into atomic flagsAlan Stern
This patch (as1393) converts several of the single-bit fields in struct usb_hcd to atomic flags. This is for safety's sake; not all CPUs can update bitfield values atomically, and these flags are used in multiple contexts. The flag fields that are set only during registration or removal can remain as they are, since non-atomic accesses at those times will not cause any problems. (Strictly speaking, the authorized_default flag should become atomic as well. I didn't bother with it because it gets changed only via sysfs. It can be done later, if anyone wants.) Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-07-26USB: musb: tusb6010: fix compile error with n8x0_defconfigFelipe Balbi
Drop the unnecessary empty stubs in tusb6010.c and avoid a compile error when building kernel for n8x0. Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-30USB: musb: Enable the maximum supported burst mode for DMAHema HK
Setting MUSB Burst Mode 3 automatically enables support for lower burst modes (BURST4, BURST8, BURST16 or bursts of unspecified length). There is no need to set these burst modes based on the packet size. Also enable the burst mode for both mode1 and mode0. This is a fix for buggy hardware - having the lower burst modes enabled can potentially cause lockups of the DMA engine used in OMAP2/3/4 chips. Signed-off-by: Hema HK <hemahk@ti.com> Signed-off-by: Anand Gadiyar <gadiyar@ti.com> Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
generated by cgit v0.10.2 at 2024-10-26 22:21:46 (GMT)