| Age | Commit message (Collapse) | Author |
|---|
|
We all know that pointless janitoring is bad, but this code is just
offensive. So:
- The error code goes directly to probe return, so don't return -1.
- Don't return return internal usb-storage codes either.
- usb_stor_control_msg takes timeout in milliseconds.
- Sanitize messages.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
D-Link DWN-652 in Modem mode exposes 3 interfaces
- First one is the USB storage one
- Second one is for both control and connection
- Third one is unknown
This patch avoids usb-storage trying to switch again when already in
modem mode, and exposes only 2 ttyUSB instead of 3 by not attaching
to the storage interface
Signed-off-by: Pascal Terjan <pterjan@mandriva.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Convert all external users of queue limits to using wrapper functions
instead of poking the request queue variables directly.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
This patch was originaly submitted by Phillip Potter
<phillipinda@hotmail.com> but was re-diffed to conform with
SubmittingPatches and to rebase on a newer tree by me.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Reported by Alessio Treglia on
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/125250
User was getting the following errors in dmesg:
[ 2158.139386] sd 5:0:0:1: ioctl_internal_command return code = 8000002
[ 2158.139390] : Current: sense key: No Sense
[ 2158.139393] Additional sense: No additional sense information
Adds unusual device support.
modified: drivers/usb/storage/unusual_devs.h
Signed-off-by: Chuck Short <zulcss@ubuntu.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Wireless USB endpoint state has a sequence number and a current
window and not just a single toggle bit. So allow HCDs to provide a
endpoint_reset method and call this or clear the software toggles as
required (after a clear halt, set configuration etc.).
usb_settoggle() and friends are then HCD internal and are moved into
core/hcd.h and all device drivers call usb_reset_endpoint() instead.
If the device endpoint state has been reset (with a clear halt) but
the host endpoint state has not then subsequent data transfers will
not complete. The device will only work again after it is reset or
disconnected.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1228) fixes a Makefile error introduced when the
subdrivers in usb-storage were split out into separate modules. The
intention is that when CONFIG_USB_LIBUSUAL is set, libusual.o and
usual-tables.o should be combined into a single object file (called
usb-libusual). The current Makefile will instead create two separate
objects, and the result won't load properly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Alan Jenkins <sourcejedi.lkml@googlemail.com>
Reported-and-tested-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1227) adds the MAX_SECTORS_64 flag to the unusual_devs
entry for the Simple Tech/Datafab controller. This fixes Bugzilla
#12882.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: binbin <binbinsh@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch allows D-Link DWM-652 3.5G modem to work.
It is an express card but was only tested with the provided usb adapter as I
don't have machines with express card connector.
/dev/ttyUSB{0,1,2} get created, and using comgt on ttyUSB1 works fine :
[root@plop tmp]# comgt -d /dev/ttyUSB1 -e
Enter PIN number: XXXX
Waiting for Registration..(120 sec max).
Registered on Home network: "Orange France",2
Signal Quality: 15,99
From: Pascal Terjan <pterjan@mandriva.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Use ATA_CMD_* defines instead of WIN_* ones.
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Factor out debug dump of id from isd200_get_inquiry_data()
to isd200_dump_driveid().
* Change id field in struct isd200_info from 'struct hd_driveid *id'
to 'u16 *id' and update driver accordingly.
* Include <linux/ata.h> directly instead of through <linux/hdreg.h>.
While at it:
* Use ata_id_u32() and ata_id_has_lba() macros.
There should be no functional changes caused by this patch.
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (119 commits)
[SCSI] scsi_dh_rdac: Retry for NOT_READY check condition
[SCSI] mpt2sas: make global symbols unique
[SCSI] sd: Make revalidate less chatty
[SCSI] sd: Try READ CAPACITY 16 first for SBC-2 devices
[SCSI] sd: Refactor sd_read_capacity()
[SCSI] mpt2sas v00.100.11.15
[SCSI] mpt2sas: add MPT2SAS_MINOR(221) to miscdevice.h
[SCSI] ch: Add scsi type modalias
[SCSI] 3w-9xxx: add power management support
[SCSI] bsg: add linux/types.h include to bsg.h
[SCSI] cxgb3i: fix function descriptions
[SCSI] libiscsi: fix possbile null ptr session command cleanup
[SCSI] iscsi class: remove host no argument from session creation callout
[SCSI] libiscsi: pass session failure a session struct
[SCSI] iscsi lib: remove qdepth param from iscsi host allocation
[SCSI] iscsi lib: have lib create work queue for transmitting IO
[SCSI] iscsi class: fix lock dep warning on logout
[SCSI] libiscsi: don't cap queue depth in iscsi modules
[SCSI] iscsi_tcp: replace scsi_debug/tcp_debug logging with iscsi conn logging
[SCSI] libiscsi_tcp: replace tcp_debug/scsi_debug logging with session/conn logging
...
|
|
modules
The lack of a MODULE_LICENSE macro in ums-* subdrivers prevented them
from loading. Needs to be applied after Alan Stern's usb-storage
subdriver separation patchset. Also added missing MODULE_DESCRIPTION and
MODULE_AUTHOR entries.
Signed-off-by: Maciej Grela <maciej.grela@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1217) converts usb-storage's onetouch subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1216) converts usb-storage's karma subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1215) converts usb-storage's alauda subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1214) converts usb-storage's jumpshot subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1213) converts usb-storage's datafab subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1212) converts usb-storage's freecom subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1211) converts usb-storage's shuttle_usbat subdriver
into a separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1210) converts usb-storage's cypress_atacb subdriver
into a separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1209) converts usb-storage's sddr55 subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1208) converts usb-storage's isd200 subdriver into a
separate module.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1207) converts usb-storage's sddr09 subdriver into a
separate module.
An unexpected complication arises because of DPCM devices, in which
one LUN uses the sddr09 transport and one uses the standard CB
transport. Since these devices can be used even when
USB_STORAGE_SDDR09 isn't configured, their entries in unusual_devs.h
require special treatment. If SDDR09 isn't configured then the
entries remain in unusual_devs.h; if it is then the entries are
present in unusual_sddr09.h instead.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1206) is the first step in converting usb-storage's
subdrivers into separate modules. It makes the following large-scale
changes:
Remove a bunch of unnecessary #ifdef's from usb_usual.h.
Not truly necessary, but it does clean things up.
Move the USB device-ID table (which is duplicated between
libusual and usb-storage) into its own source file,
usual-tables.c, and arrange for this to be linked with
either libusual or usb-storage according to whether
USB_LIBUSUAL is configured.
Add to usual-tables.c a new usb_usual_ignore_device()
function to detect whether a particular device needs to be
managed by a subdriver and not by the standard handlers
in usb-storage.
Export a whole bunch of functions in usb-storage, renaming
some of them because their names don't already begin with
"usb_stor_". These functions will be needed by the new
subdriver modules.
Split usb-storage's probe routine into two functions.
The subdrivers will call the probe1 routine, then fill in
their transport and protocol settings, and then call the
probe2 routine.
Take the default cases and error checking out of
get_transport() and get_protocol(), which run during
probe1, and instead put a check for invalid transport
or protocol values into the probe2 function.
Add a new probe routine to be used for standard devices,
i.e., those that don't need a subdriver. This new routine
checks whether the device should be ignored (because it
should be handled by ub or by a subdriver), and if not,
calls the probe1 and probe2 functions.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 64a87b24: [SCSI] Let scsi_cmnd->cmnd use request->cmd buffer
changed the scsi_eh_prep_cmnd logic by making it clear
the ->cmnd buffer. But the sat to cypress atacb translation supposed
the ->cmnd buffer wasn't modified.
This patch makes it set the ->cmnd buffer after scsi_eh_prep_cmnd call.
The problem and a fix was reported by Matthieu CASTET <castet.matthieu@free.fr>
It also removes all the hackery fiddling of scsi_cmnd and scsi_eh_save by
requesting from scsi_eh_prep_cmnd to prepare a read into ->sense_buffer,
which is much more suitable a buffer for HW transfers, then after the command
execution the regs read is copied into regs buffer before actual preparation
of sense_buffer.
Also fix an alien comment character to my utf-8 editor.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Cc: stable <stable@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Matthew Dharm <mdharm-kernel@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Make lines about usb_storage depending on SCSI visible when configuring the
kernel in a 80x25 console
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
According to kerneljanitors todo list all printk calls (beginning
a new line) should have an according KERN_* constant.
Those are the missing peaces here for the usb subsystem.
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This set of patches introduces calls to the following set of functions:
usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)
In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:
USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC
An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)
@r5@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
- \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)
@inc@
@@
#include <linux/usb.h>
@depends on !inc && (r1||r5)@
@@
+ #include <linux/usb.h>
#include <linux/usb/...>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1203) increases the max_sector limit for USB tape
drives. By default usb-storage sets max_sectors to 240 (i.e., 120 KB)
for all devices. But tape drives need a higher limit, since tapes can
and do have very large block sizes. Without the ability to transfer
an entire large block in a single command, such tapes can't be used.
This fixes Bugzilla #12207.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Phil Mitchell <philipm@sybase.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The "c-enter" USB to Toshiba 1.8" IDE enclosure needs special treatment
to work flawlessly. This patch is absolutely trivial, as the integrated
USB-IDE bridge is already identified to be an "unusual" device, only the
bcdDevice is different (lower) to the bcdDeviceMin already included in
the kernel.
It is a Prolific 2507 bridge.
T: Bus=02 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=067b ProdID=2507 Rev= 0.01
S: Manufacturer=Prolific Technology Inc.
S: Product=ATAPI-6 Bridge Controller
S: SerialNumber=00000272
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Thomas Bartosik <tbartdev@gmx-topmail.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Current firmware revision 5.60 still behaves the same,
so update the quirk up a (non-existing) 99.99 revision.
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=493415
Signed-off-by: Moritz Muehlenhoff <jmm@debian.org>
Tested-by: Jan Heitkoetter <devnull@heitkoetter.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
|
|
Enable the SD-Card interface on the GI 0431 HSUPA stick from Option.
The unusual_devs.h entry is necessary because the device descriptor is
vendor-specific. That prevents usb-storage from binding to it as an
interface driver.
T: Bus=07 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 15 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=ff Prot=ff MxPS=64 #Cfgs= 1
P: Vendor=0af0 ProdID=7501 Rev= 0.00
S: Manufacturer=Option N.V.
S: Product=Globetrotter HSUPA Modem
C:* #Ifs=11 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=hso
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=hso
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=hso
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 7 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=hso
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 9 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=hso
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0a(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#=10 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=0b(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8c(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Jan Dumon <j.dumon@option.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The SUGGEST_* flags in the SCSI command result have been out of fashion
for a while and we don't actually use them in the error handling.
Remove the remaining occurrences.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This patch (as1219) adds the IGNORE_RESIDUE flag to the unusual_devs
entries for Genesys Logic's USB-IDE adapter. Although this device
usually gets the residue correct, there is one command crucial to the
operation of CD and DVD drives which it messes up.
Tested-by: Mike Lampard <mike@mtgambier.net>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This device suffers from the off-by-one error when reporting the capacity,
so add US_FL_FIX_CAPACITY to the existing entry.
Signed-off-by: Nick Holloway <Nick.Holloway@pyrites.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1202) adds Pentax to usb-storage's list of bad vendors
whose devices always need the CAPACITY_HEURISTICS flag. This is in
addition to the existing entries: Nokia, Nikon, and Motorola.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Virgo Pärna <virgo.parna@mail.ee>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1201) removes the WARN() from the last-sector hacks in
usb-storage, thereby making the code match the version now in
.27-stable and .28-stable. The WARN() isn't needed, since there is no
longer any intention of assuming that all storage devices have an even
number of sectors, and it annoys users for no good reason.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Argosy has released another device with the off-by-one sector. This is a
harddrive with an internal cardreader which is affected.
Based on a patch written by Martijn Hijdra <martijn.hijdra@gmail.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Cc: Martijn Hijdra <martijn.hijdra@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch adds an unusual_devs entry for a Sony Ericsson modem. Like many
other modems, we have to ignore the storage device in order to access the
modem.
At this time usb_modeswitch does not work with this device.
Reported-by: The Solutor <thesolutor@gmail.com>.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The ZTE modem entry causes usb-storage to ignore the device, but for some
versions of the device, usb-storage mode is required to get to modem ode. For
both kinds the tool: http://www.draisberghof.de/usb_modeswitch/ should work.
Note that the various versions of the device have the same ProductId,
VendorId, and bcdDevice number, so we cannot have the entry for some and not
others.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This adds another unusual_devs.h entry for a device that can't handle more
than 64k reads/writes in a single command.
Signed-off-by: Jean-Baptiste Onofre <jb@nanthrax.net>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This adds an unusual devs entry for 2116:0320
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1194) makes usb-storage set the CAPACITY_HEURISTICS flag
for all devices made by Nokia, Nikon, or Motorola. These companies
seem to include the READ CAPACITY bug in all of their devices.
Since cell phones and digital cameras rely on flash storage, which
always has an even number of sectors, setting CAPACITY_HEURISTICS
shouldn't cause any problems. Not even if the companies wise up and
start making devices without the bug.
A large number of unusual_devs entries are now unnecessary, so the
patch removes them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1190) makes usb-storage's "quirks=" module parameter
writable, so that users can add entries for their devices at runtime
with no need to reboot or reload usb-storage.
New codes are added for the SANE_SENSE, CAPACITY_HEURISTICS, and
CAPACITY_OK flags.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1189b) adds some hacks to usb-storage for dealing with
the growing problems involving bad capacity values and last-sector
accesses:
A new flag, US_FL_CAPACITY_OK, is created to indicate that
the device is known to report its capacity correctly. An
unusual_devs entry for Linux's own File-backed Storage Gadget
is added with this flag set, since g_file_storage always
reports the correct capacity and since the capacity need
not be even (it is determined by the size of the backing
file).
An entry in unusual_devs.h which has only the CAPACITY_OK
flag set shouldn't prejudice libusual, since the device will
work perfectly well with either usb-storage or ub. So a
new macro, COMPLIANT_DEV, is added to let libusual know
about these entries.
When a last-sector access succeeds and the total number of
sectors is odd (the unexpected case, in which guessing that
the number is even might cause trouble), a WARN is triggered.
The kerneloops.org project will collect these warnings,
allowing us to add CAPACITY_OK flags for the devices in
question before implementing the default-to-even heuristic.
If users want to prevent the stack dump produced by the WARN,
they can disable the hack by adding an unusual_devs entry
for their device with the CAPACITY_OK flag.
When a last-sector access fails three times in a row and
neither the FIX_CAPACITY nor the CAPACITY_OK flag is set,
we assume the last-sector bug is present. We replace the
existing status and sense data with values that will cause
the SCSI core to fail the access immediately rather than
retry indefinitely. This should fix the difficulties
people have been having with Nokia phones.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Many newer Option mobile broadband devices initially provide a
usb-storage "driver CD" device that's pretty useless on Linux since
any software on it most likely wouldn't be compatible with your
kernel or distro anyway. Thus, by default just kill the driver
CD device by sending the SCSI 'rezero' command, but allow override
of the default behavior via usb-storage module parameter so users
can keep the ZeroCD device if they really want to. Inspired by
the Sierra TruInstall patch.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Peter Henn <p.henn@option.com
Cc: Denis Joseph Barrow <D.Barow@option.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The DPCM subdriver is a little peculiar, in that it's meant to support
devices where LUN 0 is Compact Flash and uses the CB transport whereas
LUN 1 is SmartMedia and uses the SDDR09 transport. Thus DPCM isn't
really a transport in itself; it's more like a demultiplexer.
Much of the DPCM code is part of the SDDR09 subdriver already, and the
remaining part is fairly small. This patch (as1182) moves that extra
piece into sddr09.c, thereby eliminating dpcm.c. Also eliminated is
the Kconfig entry for DPCM support; it is now listed as part of the
SDDR09 entry.
In order to make sure that the semantics are the same as before, each
unusual_devs entry for DPCM is now present twice: once with DPCM
support if SDDR09 is configured (as before), and once with the
SINGLE_LUN flag and CB support otherwise.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1175) makes usb-storage set a SCSI device's
request-queue bounce limit such that all buffers will be located in
addressable memory (i.e., not in high memory) if the host controller's
dma_mask is NULL. This is necessary when the host controller doesn't
support DMA: If a buffer is in high memory then the both the virtual
and DMA addresses produced by the scatter-gather library will be NULL,
preventing the HCD from accessing the buffer's data.
In particular, the isp1760 driver needs this when used on a system
with more than 1 GB of memory.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Tested-by: Thomas Hommel <Thomas.Hommel@gefanuc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
