| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Make sure we check the truncate constraints early on in ->setattr by adding
those checks to inode_change_ok. Also clean up and document inode_change_ok
to make this obvious.
As a fallout we don't have to call inode_newsize_ok from simple_setsize and
simplify it down to a truncate_setsize which doesn't return an error. This
simplifies a lot of setattr implementations and means we use truncate_setsize
almost everywhere. Get rid of fat_setsize now that it's trivial and mark
ext2_setsize static to make the calling convention obvious.
Keep the inode_newsize_ok in vmtruncate for now as all callers need an
audit for its removal anyway.
Note: setattr code in ecryptfs doesn't call inode_change_ok at all and
needs a deeper audit, but that is left for later.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Replace inode_setattr with opencoded variants of it in all callers. This
moves the remaining call to vmtruncate into the filesystem methods where it
can be replaced with the proper truncate sequence.
In a few cases it was obvious that we would never end up calling vmtruncate
so it was left out in the opencoded variant:
spufs: explicitly checks for ATTR_SIZE earlier
btrfs,hugetlbfs,logfs,dlmfs: explicitly clears ATTR_SIZE earlier
ufs: contains an opencoded simple_seattr + truncate that sets the filesize just above
In addition to that ncpfs called inode_setattr with handcrafted iattrs,
which allowed to trim down the opencoded variant.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Move the call to vmtruncate to get rid of accessive blocks to the callers
in prepearation of the new truncate calling sequence. This was only done
for DIO_LOCKING filesystems, so the __blockdev_direct_IO_newtrunc variant
was not needed anyway. Get rid of blockdev_direct_IO_no_locking and
its _newtrunc variant while at it as just opencoding the two additional
paramters is shorted than the name suffix.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Filesystems with unwritten extent support must not complete an AIO request
until the transaction to convert the extent has been commited. That means
the aio_complete calls needs to be moved into the ->end_io callback so
that the filesystem can control when to call it exactly.
This makes a bit of a mess out of dio_complete and the ->end_io callback
prototype even more complicated.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Alex Elder <aelder@sgi.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
ocfs2: Silence gcc warning in ocfs2_write_zero_page().
jbd2/ocfs2: Fix block checksumming when a buffer is used in several transactions
ocfs2/dlm: Remove BUG_ON from migration in the rare case of a down node
ocfs2: Don't duplicate pages past i_size during CoW.
ocfs2: tighten up strlen() checking
ocfs2: Make xattr reflink work with new local alloc reservation.
ocfs2: make xattr extension work with new local alloc reservation.
ocfs2: Remove the redundant cpu_to_le64.
ocfs2/dlm: don't access beyond bitmap size
ocfs2: No need to zero pages past i_size.
ocfs2: Zero the tail cluster when extending past i_size.
ocfs2: When zero extending, do it by page.
ocfs2: Limit default local alloc size within bitmap range.
ocfs2: Move orphan scan work to ocfs2_wq.
fs/ocfs2/dlm: Add missing spin_unlock
|
|
ocfs2_write_zero_page() has a loop that won't ever be skipped, but gcc
doesn't know that. Set ret=0 just to make gcc happy.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
|
|
OCFS2 uses t_commit trigger to compute and store checksum of the just
committed blocks. When a buffer has b_frozen_data, checksum is computed
for it instead of b_data but this can result in an old checksum being
written to the filesystem in the following scenario:
1) transaction1 is opened
2) handle1 is opened
3) journal_access(handle1, bh)
- This sets jh->b_transaction to transaction1
4) modify(bh)
5) journal_dirty(handle1, bh)
6) handle1 is closed
7) start committing transaction1, opening transaction2
8) handle2 is opened
9) journal_access(handle2, bh)
- This copies off b_frozen_data to make it safe for transaction1 to commit.
jh->b_next_transaction is set to transaction2.
10) jbd2_journal_write_metadata() checksums b_frozen_data
11) the journal correctly writes b_frozen_data to the disk journal
12) handle2 is closed
- There was no dirty call for the bh on handle2, so it is never queued for
any more journal operation
13) Checkpointing finally happens, and it just spools the bh via normal buffer
writeback. This will write b_data, which was never triggered on and thus
contains a wrong (old) checksum.
This patch fixes the problem by calling the trigger at the moment data is
frozen for journal commit - i.e., either when b_frozen_data is created by
do_get_write_access or just before we write a buffer to the log if
b_frozen_data does not exist. We also rename the trigger to t_frozen as
that better describes when it is called.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
|
|
For migration, we are waiting for DLM_LOCK_RES_MIGRATING flag to be set
before sending DLM_MIG_LOCKRES_MSG message to the target. We are using
dlm_migration_can_proceed() for that purpose. However, if the node is
down, dlm_migration_can_proceed() will also return "go ahead". In this
rare case, the DLM_LOCK_RES_MIGRATING flag might not be set yet. Remove
the BUG_ON() that trips over this condition.
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
|
|
During CoW, the pages after i_size don't contain valid data, so there's
no need to read and duplicate them.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
|
|
This function is only called from one place and it's like this:
dlm_register_domain(conn->cc_name, dlm_key, &fs_version);
The "conn->cc_name" is 64 characters long. If strlen(conn->cc_name)
were equal to O2NM_MAX_NAME_LEN (64) that would be a bug because
strlen() doesn't count the NULL character.
In fact, if you look how O2NM_MAX_NAME_LEN is used, it mostly describes
64 character buffers. The only exception is nd_name from struct
o2nm_node.
Anyway I looked into it and in this case the domain string comes from
osb->uuid_str in ocfs2_setup_osb_uuid(). That's 32 characters and NULL
which easily fits into O2NM_MAX_NAME_LEN. This patch doesn't change how
the code works, but I think it makes the code a little cleaner.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
|
|
The new reservation code in local alloc has add the limitation
that the caller should handle the case that the local alloc
doesn't give use enough contiguous clusters. It make the old
xattr reflink code broken.
So this patch udpate the xattr reflink code so that it can
handle the case that local alloc give us one cluster at a time.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
|
|
The old ocfs2_xattr_extent_allocation is too optimistic about
the clusters we can get. So actually if the file system is
too fragmented, ocfs2_add_clusters_in_btree will return us
with EGAIN and we need to allocate clusters once again.
So this patch change it to a while loop so that we can allocate
clusters until we reach clusters_to_add.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Cc: stable@kernel.org
|
|
In ocfs2_block_group_alloc, we set c_blkno by bg->bg_blkno.
But actually bg->bg_blkno is already changed to little endian
in ocfs2_block_group_fill. So remove the extra cpu_to_le64.
Reported-by: Marcos Matsunaga <Marcos.Matsunaga@oracle.com>
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
|
|
dlm->recovery_map is defined as
unsigned long recovery_map[BITS_TO_LONGS(O2NM_MAX_NODES)];
We should treat O2NM_MAX_NODES as the bit map size in bits.
This patches fixes a bit operation that takes O2NM_MAX_NODES + 1 as bitmap size.
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
|
|
When ocfs2 fills a hole, it does so by allocating clusters. When a
cluster is larger than the write, ocfs2 must zero the portions of the
cluster outside of the write. If the clustersize is smaller than a
pagecache page, this is handled by the normal pagecache mechanisms, but
when the clustersize is larger than a page, ocfs2's write code will zero
the pages adjacent to the write. This makes sure the entire cluster is
zeroed correctly.
Currently ocfs2 behaves exactly the same when writing past i_size.
However, this means ocfs2 is writing zeroed pages for portions of a new
cluster that are beyond i_size. The page writeback code isn't expecting
this. It treats all pages past the one containing i_size as left behind
due to a previous truncate operation.
Thankfully, ocfs2 calculates the number of pages it will be working on
up front. The rest of the write code merely honors the original
calculation. We can simply trim the number of pages to only cover the
actual file data.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Cc: stable@kernel.org
|
|
ocfs2's allocation unit is the cluster. This can be larger than a block
or even a memory page. This means that a file may have many blocks in
its last extent that are beyond the block containing i_size. There also
may be more unwritten extents after that.
When ocfs2 grows a file, it zeros the entire cluster in order to ensure
future i_size growth will see cleared blocks. Unfortunately,
block_write_full_page() drops the pages past i_size. This means that
ocfs2 is actually leaking garbage data into the tail end of that last
cluster. This is a bug.
We adjust ocfs2_write_begin_nolock() and ocfs2_extend_file() to detect
when a write or truncate is past i_size. They will use
ocfs2_zero_extend() to ensure the data is properly zeroed.
Older versions of ocfs2_zero_extend() simply zeroed every block between
i_size and the zeroing position. This presumes three things:
1) There is allocation for all of these blocks.
2) The extents are not unwritten.
3) The extents are not refcounted.
(1) and (2) hold true for non-sparse filesystems, which used to be the
only users of ocfs2_zero_extend(). (3) is another bug.
Since we're now using ocfs2_zero_extend() for sparse filesystems as
well, we teach ocfs2_zero_extend() to check every extent between
i_size and the zeroing position. If the extent is unwritten, it is
ignored. If it is refcounted, it is CoWed. Then it is zeroed.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Cc: stable@kernel.org
|
|
ocfs2_zero_extend() does its zeroing block by block, but it calls a
function named ocfs2_write_zero_page(). Let's have
ocfs2_write_zero_page() handle the page level. From
ocfs2_zero_extend()'s perspective, it is now page-at-a-time.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Cc: stable@kernel.org
|
|
Implicit slab.h inclusion via percpu.h is about to go away. Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
|
|
In commit 6b82021b9e91cd689fdffadbcdb9a42597bbe764, we increase
our local alloc size and calculate how much megabytes we can
get according to group size and volume size.
But we also need to check the maximum bits a local alloc block
bitmap can have. With a bs=512, cs=32K, local volume with 160G,
it calculate 96MB while the maximum local alloc size is only
76M. So the bitmap will overflow and corrupt the system truncate
log file. See bug
http://oss.oracle.com/bugzilla/show_bug.cgi?id=1262
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Acked-by: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
|
|
We used to let orphan scan work in the default work queue,
but there is a corner case which will make the system deadlock.
The scenario is like this:
1. set heartbeat threadshold to 200. this will allow us to have a
great chance to have a orphan scan work before our quorum decision.
2. mount node 1.
3. after 1~2 minutes, mount node 2(in order to make the bug easier
to reproduce, better add maxcpus=1 to kernel command line).
4. node 1 do orphan scan work.
5. node 2 do orphan scan work.
6. node 1 do orphan scan work. After this, node 1 hold the orphan scan
lock while node 2 know node 1 is the master.
7. ifdown eth2 in node 2(eth2 is what we do ocfs2 interconnection).
Now when node 2 begins orphan scan, the system queue is blocked.
The root cause is that both orphan scan work and quorum decision work
will use the system event work queue. orphan scan has a chance of
blocking the event work queue(in dlm_wait_for_node_death) so that there
is no chance for quorum decision work to proceed.
This patch resolve it by moving orphan scan work to ocfs2_wq.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
|
|
Add a spin_unlock missing on the error path. Unlock as in the other code
that leads to the leave label.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E1;
@@
* spin_lock(E1,...);
<+... when != E1
if (...) {
... when != E1
* return ...;
}
...+>
* spin_unlock(E1,...);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
quota: Convert quota statistics to generic percpu_counter
ext3 uses rb_node = NULL; to zero rb_root.
quota: Fixup dquot_transfer
reiserfs: Fix resuming of quotas on remount read-write
pohmelfs: Remove dead quota code
ufs: Remove dead quota code
udf: Remove dead quota code
quota: rename default quotactl methods to dquot_
quota: explicitly set ->dq_op and ->s_qcop
quota: drop remount argument to ->quota_on and ->quota_off
quota: move unmount handling into the filesystem
quota: kill the vfs_dq_off and vfs_dq_quota_on_remount wrappers
quota: move remount handling into the filesystem
ocfs2: Fix use after free on remount read-only
Fix up conflicts in fs/ext4/super.c and fs/ufs/file.c
|
|
Lots of filesystems calls vmtruncate despite not implementing the old
->truncate method. Switch them to use simple_setsize and add some
comments about the truncate code where it seems fitting.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
SHRT_MAX and SHRT_MIN
- C99 knows about USHRT_MAX/SHRT_MAX/SHRT_MIN, not
USHORT_MAX/SHORT_MAX/SHORT_MIN.
- Make SHRT_MIN of type s16, not int, for consistency.
[akpm@linux-foundation.org: fix drivers/dma/timb_dma.c]
[akpm@linux-foundation.org: fix security/keys/keyring.c]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Follow the dquot_* style used elsewhere in dquot.c.
[Jan Kara: Fixed up missing conversion of ext2]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Remount handling has fully moved into the filesystem, so all this is
superflous now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Instead of having wrappers in the VFS namespace export the dquot_suspend
and dquot_resume helpers directly. Also rename vfs_quota_disable to
dquot_disable while we're at it.
[Jan Kara: Moved dquot_suspend to quotaops.h and made it inline]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
We also have to cancel quota syncing thread on remount read only because
at that moment quota is being turned off. Otherwise quota syncing thread
will try to access already freed quota structures.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Acked-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
We cannot cancel delayed work from ocfs2_local_free_info because that is called
with dqonoff_mutex held and the work it cancels requires dqonoff_mutex to
finish. Cancel the work before acquiring dqonoff_mutex.
Acked-by: Joel Becker <Joel.Becker@oracle.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
dquot_transfer() acquires own references to dquots via dqget(). Thus it waits
for dq_lock which creates a lock inversion because dq_lock ranks above
transaction start but transaction is already started in ocfs2_setattr(). Fix
the problem by passing own references directly to __dquot_transfer.
Acked-by: Joel Becker <Joel.Becker@oracle.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
commit_dqblk() can write quota info to global file. That is actually a bad
thing to do because if we are just modifying local quota file, we are not
prepared (do not hold proper locks, do not have transaction credits) to do
a modification of the global quota file. So do not use commit_dqblk() and
instead call our writing function directly.
Acked-by: Joel Becker <Joel.Becker@oracle.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
We were missing reservation of a journal credit for modification of quota
file inode when creating new dquot structure in the global quota file.
Acked-by: Joel Becker <Joel.Becker@oracle.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
OCFS2 had three issues with quota locking:
a) When reading dquot from global quota file, we started a transaction while
holding dqio_mutex which is prone to deadlocks because other paths do it
the other way around
b) During ocfs2_sync_dquot we were not protected against concurrent writers
on the same node. Because we first copy data to local buffer, a race
could happen resulting in old data being written to global quota file and
thus causing quota inconsistency after a crash.
c) ip_alloc_sem of quota files was acquired while a transaction is started
in ocfs2_quota_write which can deadlock because we first get ip_alloc_sem
and then start a transaction when extending quota files.
We fix the problem a) by pulling all necessary code to ocfs2_acquire_dquot
and ocfs2_release_dquot. Thus we no longer depend on generic dquot_acquire
to do the locking and can force proper lock ordering.
Problems b) and c) are fixed by locking i_mutex and ip_alloc_sem of
global quota file in ocfs2_lock_global_qf and removing ip_alloc_sem from
ocfs2_quota_read and ocfs2_quota_write.
Acked-by: Joel Becker <Joel.Becker@oracle.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
The position of global quota file info does not change. So we do not have
to do logical -> physical block translation every time we reread it from
disk. Thus we can also avoid taking ip_alloc_sem.
Acked-by: Joel Becker <Joel.Becker@oracle.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
There is no need to map offset of local dquot structure to on disk block
in each quota write. It is enough to map it just once and store the physical
block number in quota structure in memory. Moreover this simplifies locking
as we do not have to take ip_alloc_sem from quota write path.
Acked-by: Joel Becker <Joel.Becker@oracle.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Quota must being initialized if size or uid/git changes requested.
But initialization performed in two different places:
in case of i_size file system is responsible for dquot init
, but in case of uid/gid init will be called internally in
dquot_transfer().
This ambiguity makes code harder to understand.
Let's move this logic to one common helper function.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2: (47 commits)
ocfs2: Silence a gcc warning.
ocfs2: Don't retry xattr set in case value extension fails.
ocfs2:dlm: avoid dlm->ast_lock lockres->spinlock dependency break
ocfs2: Reset xattr value size after xa_cleanup_value_truncate().
fs/ocfs2/dlm: Use kstrdup
fs/ocfs2/dlm: Drop memory allocation cast
Ocfs2: Optimize punching-hole code.
Ocfs2: Make ocfs2_find_cpos_for_left_leaf() public.
Ocfs2: Fix hole punching to correctly do CoW during cluster zeroing.
Ocfs2: Optimize ocfs2 truncate to use ocfs2_remove_btree_range() instead.
ocfs2: Block signals for mkdir/link/symlink/O_CREAT.
ocfs2: Wrap signal blocking in void functions.
ocfs2/dlm: Increase o2dlm lockres hash size
ocfs2: Make ocfs2_extend_trans() really extend.
ocfs2/trivial: Code cleanup for allocation reservation.
ocfs2: make ocfs2_adjust_resv_from_alloc simple.
ocfs2: Make nointr a default mount option
ocfs2/dlm: Make o2dlm domain join/leave messages KERN_NOTICE
o2net: log socket state changes
ocfs2: print node # when tcp fails
...
|
|
ocfs2_block_group_claim_bits() is never called with min_bits=0, but we
shouldn't leave status undefined if it ever is.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
|
|
In normal xattr set, the set sequence is inode, xattr block
and finally xattr bucket if we meet with a ENOSPC. But there
is a corner case.
So consider we will set a xattr whose value will be stored in
a cluster, and there is no xattr block by now. So we will
reserve 1 xattr block and 1 cluster for setting it. Now if we
fail in value extension(in case the volume is almost full and
we can't allocate the cluster because the check in
ocfs2_test_bg_bit_allocatable), ENOSPC will be returned. So
we will try to create a bucket(this time there is a chance that
the reserved cluster will be used), and when we try value extension
again, kernel bug happens. We did meet with it. Check the bug below.
http://oss.oracle.com/bugzilla/show_bug.cgi?id=1251
This patch just try to avoid this by adding a set_abort in
ocfs2_xattr_set_ctxt, so in case ENOSPC happens in value extension,
we will check whether it is caused by the real ENOSPC or just the
full of inode or xattr block. If it is the first case, we set set_abort
so that we don't try any further. we are safe to exit directly here
ince it is really ENOSPC.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
|
|
Currently we process a dirty lockres with the lockres->spinlock taken. While
during the process, we may need to lock on dlm->ast_lock. This breaks the
dependency of dlm->ast_lock(lock first) and lockres->spinlock(lock second).
This patch fixes the problem.
Since we can't release lockres->spinlock, we have to take dlm->ast_lock
just before taking the lockres->spinlock and release it after lockres->spinlock
is released. And use __dlm_queue_bast()/__dlm_queue_ast(), the nolock version,
in dlm_shuffle_lists(). There are no too many locks on a lockres, so there is no
performance harm.
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
|
|
In ocfs2_prepare_xattr_entry, if we fail to grow an existing value,
xa_cleanup_value_truncate() will leave the old entry in place. Thus, we
reset its value size. However, if we were allocating a new value, we
must not reset the value size or we will BUG(). This resolves
oss.oracle.com bug 1247.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
|
|
ocfs2-merge-window
|
|
Use kstrdup when the goal of an allocation is copy a string into the
allocated region.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to;
expression flag,E1,E2;
statement S;
@@
- to = kmalloc(strlen(from) + 1,flag);
+ to = kstrdup(from, flag);
... when != \(from = E1 \| to = E1 \)
if (to==NULL || ...) S
... when != \(from = E2 \| to = E2 \)
- strcpy(to, from);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
|
|
Drop cast on the result of kmalloc and similar functions.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
@@
- (T *)
(\(kmalloc\|kzalloc\|kcalloc\|kmem_cache_alloc\|kmem_cache_zalloc\|
kmem_cache_alloc_node\|kmalloc_node\|kzalloc_node\)(...))
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
|
|
This patch simplifies the logic of handling existing holes and
skipping extent blocks and removes some confusing comments.
The patch survived the fill_verify_holes testcase in ocfs2-test.
It also passed my manual sanity check and stress tests with enormous
extent records.
Currently punching a hole on a file with 3+ extent tree depth was
really a performance disaster. It can even take several hours,
though we may not hit this in real life with such a huge extent
number.
One simple way to improve the performance is quite straightforward.
From the logic of truncate, we can punch the hole from hole_end to
hole_start, which reduces the overhead of btree operations in a
significant way, such as tree rotation and moving.
Following is the testing result when punching hole from 0 to file end
in bytes, on a 1G file, 1G file consists of 256k extent records, each record
cover 4k data(just one cluster, clustersize is 4k):
===========================================================================
* Original punching-hole mechanism:
===========================================================================
I waited 1 hour for its completion, unfortunately it's still ongoing.
===========================================================================
* Patched punching-hode mechanism:
===========================================================================
real 0m2.518s
user 0m0.000s
sys 0m2.445s
That means we've gained up to 1000 times improvement on performance in this
case, whee! It's fairly cool. and it looks like that performance gain will
be raising when extent records grow.
The patch was based on my former 2 patches, which were about truncating
codes optimization and fixup to handle CoW on punching hole.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com>
Acked-by: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
|
|
The original idea to pull ocfs2_find_cpos_for_left_leaf() out of
alloc.c is to benefit punching-holes optimization patch, it however,
can also be referred by other funcs in the future who want to do the
same job.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com>
Acked-by: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
|
