| Age | Commit message (Collapse) | Author |
|---|
|
AB8500 sysctrl driver implements a pm_power_off handler, but that is
currently not registered until a specific platform data field is
enabled.
This patch drops the platform data field and always registers
ab8500_power_off if no other pm_power_off handler was defined before,
and also introduces the necessary cleanup code in the driver's remove
function.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next
Pull MFD update from Samuel Ortiz:
"For 3.10 we have a few new MFD drivers for:
- The ChromeOS embedded controller which provides keyboard, battery
and power management services. This controller is accessible
through i2c or SPI.
- Silicon Laboratories 476x controller, providing access to their FM
chipset and their audio codec.
- Realtek's RTS5249, a memory stick, MMC and SD/SDIO PCI based
reader.
- Nokia's Tahvo power button and watchdog device. This device is
very similar to Retu and is thus supported by the same code base.
- STMicroelectronics STMPE1801, a keyboard and GPIO controller
supported by the stmpe driver.
- ST-Ericsson AB8540 and AB8505 power management and voltage
converter controllers through the existing ab8500 code.
Some other drivers got cleaned up or improved. In particular:
- The Linaro/STE guys got the ab8500 driver in sync with their
internal code through a series of optimizations, fixes and
improvements.
- The AS3711 and OMAP USB drivers now have DT support.
- The arizona clock and interrupt handling code got improved.
- The wm5102 register patch and boot mechanism also got improved."
* tag 'mfd-3.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next: (104 commits)
mfd: si476x: Don't use 0bNNN
mfd: vexpress: Handle pending config transactions
mfd: ab8500: Export ab8500_gpadc_sw_hw_convert properly
mfd: si476x: Fix i2c warning
mfd: si476x: Add header files and Kbuild plumbing
mfd: si476x: Add chip properties handling code
mfd: si476x: Add the bulk of the core driver
mfd: si476x: Add commands abstraction layer
mfd: rtsx: Support RTS5249
mfd: retu: Add Tahvo support
mfd: ucb1400: Pass ucb1400-gpio data through ac97 bus
mfd: wm8994: Add some OF properties
mfd: wm8994: Add device ID data to WM8994 OF device IDs
input: Export matrix_keypad_parse_of_params()
mfd: tps65090: Add compatible string for charger subnode
mfd: db8500-prcmu: Support platform dependant device selection
mfd: syscon: Fix warnings when printing resource_size_t
of: Add stub of_get_parent for non-OF builds
mfd: omap-usb-tll: Convert to devm_ioremap_resource()
mfd: omap-usb-host: Convert to devm_ioremap_resource()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"Mostly many small changes spread as seen in diffstat in sound/*
directory by this update. A significant change in the subsystem level
is the introduction of snd_soc_component, which will help more generic
handling of SoC and off-SoC components.
Also, snd_BUG_ON() macro is enabled unconditionally now due to its
misuses, so people might hit kernel warnings (it's a good thing for
us).
- compress-offload: support for capture by Charles Keepax
- HD-audio: codec delay support by Dylan Reid
- HD-audio: improvements/fixes in generic parser: better headphone
mic and headset mic support, jack_modes hint consolidation, proper
beep attach/detachment, generalized power filter controls by David
Henningsson, et al
- HD-audio: Improved management of HDMI codec pins/converters
- HD-audio: Better pin/DAC assignment for VIA codecs
- HD-audio: Haswell HDMI workarounds
- HD-audio: ALC268 codec support, a few new quirks for Chromebooks
- USB: regression fixes: USB-MIDI autopm fix, the recent ISO latency
fix by Clemens Ladisch
- USB: support for DSD formats by Daniel Mack
- USB: A few UAC2 device endian/cock fixes by Eldad Zack
- USB: quirks for Emu 192kHz support, Novation Twitch DJ controller,
Yamaha THRxx devices
- HDSPM: updates for TCO controls by Adrian Knoth
- ASoC: Add a snd_soc_component object type for generic handling of
SoC and off-SoC components by Kuninori Morimoto,
- dmaengine: a large set of cleanups and conversions by Lars-Peter
Clausen
- ASoC DAPM: performance optimizations from Ryo Tsutsui
- ASoC DAPM: support for mixer control sharing by Stephen Warren
- ASoC: multiplatform ARM cleanups from Arnd Bergmann
- ASoC: new codec drivers for AK5385 and TAS5086 from Daniel Mack"
* tag 'sound-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (315 commits)
ALSA: usb-audio: caiaq: fix endianness bug in snd_usb_caiaq_maschine_dispatch
ALSA: asihpi: add format support check in snd_card_asihpi_capture_formats
ALSA: pcm_format_to_bits strong-typed conversion
ALSA: compress: fix the states to check for allowing read
ALSA: hda - Move Thinkpad X220 to use auto parser
ALSA: USB: adjust for changed 3.8 USB API
ALSA: usb - Avoid unnecessary sample rate changes on USB 2.0 clock sources
sound: oss/dmabuf: use dma_map_single
ALSA: ali5451: use mdelay instead of large udelay constants
ALSA: hda - Add the support for ALC286 codec
ALSA: usb-audio: USB quirk for Yamaha THR10C
ALSA: usb-audio: USB quirk for Yamaha THR5A
ALSA: usb-audio: USB quirk for Yamaha THR10
ALSA: usb-audio: Fix autopm error during probing
ALSA: snd-usb: try harder to find USB_DT_CS_ENDPOINT
ALSA: sound kconfig typo
ALSA: emu10k1: Fix dock firmware loading
ASoC: ux500: forward declare msp_i2s_platform_data
ASoC: davinci-mcasp: Add Support BCLK-to-LRCLK ratio for TDM modes
ASoC: davinci-pcm, davinci-mcasp: Clean up active_serializers
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform updates from Olof Johansson:
"More multiplatform enablement for ARM platforms. The ones converted
in this branch are:
- bcm2835
- cns3xxx
- sirf
- nomadik
- msx
- spear
- tegra
- ux500
We're getting close to having most of them converted!
One of the larger platforms remaining is Samsung Exynos, and there are
a bunch of supporting patches in this merge window for it. There was
a patch in this branch to a early version of multiplatform conversion,
but it ended up being reverted due to need of more bake time. The
revert commit is part of the branch since it would have required
rebasing multiple dependent branches and they were stable by then"
* tag 'multiplatform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (70 commits)
mmc: sdhci-s3c: Fix operation on non-single image Samsung platforms
clocksource: nomadik-mtu: fix up clocksource/timer
Revert "ARM: exynos: enable multiplatform support"
ARM: SPEAr13xx: Fix typo "ARCH_HAVE_CPUFREQ"
ARM: exynos: enable multiplatform support
rtc: s3c: make header file local
mtd: onenand/samsung: make regs-onenand.h file local
thermal/exynos: remove unnecessary header inclusions
mmc: sdhci-s3c: remove platform dependencies
ARM: samsung: move mfc device definition to s5p-dev-mfc.c
ARM: exynos: move debug-macro.S to include/debug/
ARM: exynos: prepare for sparse IRQ
ARM: exynos: introduce EXYNOS_ATAGS symbol
ARM: tegra: build assembly files with -march=armv7-a
ARM: Push selects for TWD/SCU into machine entries
ARM: ux500: build hotplug.o for ARMv7-a
ARM: ux500: move to multiplatform
ARM: ux500: make remaining headers local
ARM: ux500: make irqs.h local to platform
ARM: ux500: get rid of <mach/[hardware|db8500-regs].h>
...
|
|
Pull battery updates from Anton Vorontsov:
"Highlights:
- OpenFirmware/DeviceTree support for the Power Supply core: the core
now automatically populates supplied_from hierarchy from the device
tree. With these patches chargers and batteries can now lookup
each other without the board files support shim. Rhyland Klein at
NVIDIA did the work
- New ST-Ericsson ABX500 hwmon driver. The driver is heavily using
the AB85xx core and depends on some recent changes to it, so that
is why the driver comes through the battery tree. It has an
appropriate ack from the hwmon maintainer (i.e. Guenter Roeck).
Martin Persson at ST-Ericsson and Hongbo Zhang at Linaro authored
the driver
- Final bits to sync AB85xx ST-Ericsson changes into mainline. The
changes touch mfd parts, but these were acked by the appropriate
MFD maintainer (ie Samuel Ortiz). Lee Jones at Linaro did most of
the work and lead the submission process.
Minor changes, but still worth mentioning:
- Battery temperature reporting fix for Nokia N900 phones
- Versatile Express poweroff driver moved into drivers/power/reset/
- Tree-wide: use devm_kzalloc() where appropriate
- Tree-wide: dev_pm_ops cleanups/fixes"
* tag 'for-v3.10' of git://git.infradead.org/battery-2.6: (112 commits)
pm2301-charger: Fix suspend/resume
charger-manager: Use kmemdup instead of kzalloc + memcpy
power_supply: Populate supplied_from hierarchy from the device tree
power_supply: Add core support for supplied_from
power_supply: Define Binding for power-supplies
rx51_battery: Fix reporting temperature
hwmon: Add ST-Ericsson ABX500 hwmon driver
ab8500_bmdata: Export abx500_res_to_temp tables for hwmon
ab8500_{bmdata,fg}: Add const attributes to some data arrays
ab8500_bmdata: Eliminate CamelCase warning of some variables
ab8500_btemp: Make ab8500_btemp_get* interfaces public
goldfish_battery: Use resource_size()
lp8788-charger: Use PAGE_SIZE for the sysfs read operation
max8925_power: Use devm_kzalloc()
da9030_battery: Use devm_kzalloc()
da9052-battery: Use devm_kzalloc()
ds2760_battery: Use devm_kzalloc()
ds2780_battery: Use devm_kzalloc()
gpio-charger: Use devm_kzalloc()
isp1704_charger: Use devm_kzalloc()
...
|
|
Merge second batch of fixes from Andrew Morton:
- various misc bits
- some printk updates
- a new "SRAM" driver.
- MAINTAINERS updates
- the backlight driver queue
- checkpatch updates
- a few init/ changes
- a huge number of drivers/rtc changes
- fatfs updates
- some lib/idr.c work
- some renaming of the random driver interfaces
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (285 commits)
net: rename random32 to prandom
net/core: remove duplicate statements by do-while loop
net/core: rename random32() to prandom_u32()
net/netfilter: rename random32() to prandom_u32()
net/sched: rename random32() to prandom_u32()
net/sunrpc: rename random32() to prandom_u32()
scsi: rename random32() to prandom_u32()
lguest: rename random32() to prandom_u32()
uwb: rename random32() to prandom_u32()
video/uvesafb: rename random32() to prandom_u32()
mmc: rename random32() to prandom_u32()
drbd: rename random32() to prandom_u32()
kernel/: rename random32() to prandom_u32()
mm/: rename random32() to prandom_u32()
lib/: rename random32() to prandom_u32()
x86: rename random32() to prandom_u32()
x86: pageattr-test: remove srandom32 call
uuid: use prandom_bytes()
raid6test: use prandom_bytes()
sctp: convert sctp_assoc_set_id() to use idr_alloc_cyclic()
...
|
|
Signed-off-by: Matus Ujhelyi <matus.ujhelyi@streamunlimited.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The diffstat and changelog here is dominated by Lee Jones' heroic
efforts to sync the ab8500 driver that's been maintained out of tree
with mainline (plus Axel's cleanup work on the results) but there's a
few other things here:
- Axel Lin added regulator_map_voltage_ascend() optimising a common
pattern for drivers using the core code.
- Milo Kim tought the regulator core to handle regulators sharing an
enable GPIO, avoiding the need to do hacks to support such systems.
- Andrew Bresticker added code to handle missing supplies for
regulators more sensibly for device tree systems, reducing the need
for stubbing there.
plus the usual batch of driver specific updates and fixes"
* tag 'regulator-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (152 commits)
regulator: mc13892: Fix MC13892_SWITCHERS0_SWxHI bit in set_voltage_sel
regulator: Remove NULL test before calling regulator_unregister()
regulator: mc13783: Add device tree probe support
regulator: mc13xxx: Add warning of incorrect names of regulators
regulator: max77686: Don't update max77686->opmode if update register fails
regulator: max8952: Add missing config.of_node setting for regulator register
regulator: ab3100: Fix regulator register error handling
regulator: tps6524x: Use regulator_map_voltage_ascend
regulator: lp8788-buck: Use regulator_map_voltage_ascend
regulator: lp872x: Use regulator_map_voltage_ascend
regulator: mc13892: Use regulator_map_voltage_ascend for mc13892_sw_regulator_ops
regulator: tps65023: Use regulator_map_voltage_ascend
regulator: tps65023: Merge tps65020 ldo1 and ldo2 vsel table
regulator: tps6507x: Use regulator_map_voltage_ascend
regulator: mc13892: Fix MC13892_SWITCHERS0_SWxHI bit in set_voltage_sel
regulator: ab3100: device tree support
regulator: ab3100: refactor probe to use IDs
regulator: max8973: Don't override control1 variable when set ramp delay bits
regulator: tps80031: Convert tps80031_dcdc_ops to [get|set]_voltage_sel_regmap
regulator: tps80031: Fix LDO2 track mode for TPS80031 or TPS80032-ES1.0
...
|
|
|
|
|
|
This doesn't compile with sparc64 gcc-3.4.5.
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch adds all necessary header files and Kbuild plumbing for the
core driver for Silicon Laboratories Si476x series of AM/FM tuner
chips.
The driver as a whole is implemented as an MFD device and this patch
adds a core portion of it that provides all the necessary
functionality to the two other drivers that represent radio and audio
codec subsystems of the chip.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
RTS5249 supports SD UHS-II interface.
In order to support SD UHS-II，the definitions of some internal
registers of RTS5249 have to be modified and are different from its
predecessors. So we need this patch to ensure RTS5249 can work, even
SD/MMC stack doesn't support UHS-II interface.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Tahvo is a multi-function device on Nokia 770, implementing USB
transceiver and charge/battery control.
It's so close to Retu that a single driver can support both.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The Palma device like TPS65913 have the mode mask which is also
used for enable/disable the rails. The mode bits are defined as
00: OFF
01: AUTO
10: ECO
11: Forced PWM
and modes are set accordingly as
REGULATOR_MODE_NORMAL: AUTO
REGULATOR_MODE_IDLE: ECO
REGULATOR_MODE_FAST: PWM
Two issue observed:
1. If client calls following sequence:
regulator_enable(),
regulator_set_mode(FAST),
regulator_disable()
and again the regulator_enable() then the mode is reset
to NORMAL inplace of keeping the mode as FAST.
Fixing this by storing the current mode configured by client
and restoring modes when enable() is called after disable().
2. In following sequence, the regulator get enabled:
regulator_disable()
regulator_set_mode(FAST),
Fixing this by updating new mode in register only if it is
enabled.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Currently Palma regulator driver support the ramp delay
through rail specific platform data.
As regulator framework support the configuration of ramp
delay through regulator constraint, using the framework
method and removing the platform specific data approach.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
LDO8 of Palma device like tps65913 support the tracking mode
on which LDO8 track the SMPS45 voltage when SMPS45 is ON
and use the LDO8.VOLTAGE_SEL register when SMPS45 is OFF.
On track mode, the steps of voltage change for LDO8 is 25mV
where in non-tracking mode it is 50mV. Set the steps accordingly.
Number of voltage count is still same for both the cases.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Palmas device have control outputs like REGEN1, REGEN2, REGEN3,
SYSEN1 and SYSEN2. These control outputs can be used for controlling
external voltage switches to enabled/disable voltage outputs.
Add support of these control outputs through regulator framework.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
This patch adds const attributes to AB8500 power and temperature related
read-only data arrays.
Signed-off-by: Hongbo Zhang <hongbo.zhang@linaro.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
Make ab8500_btemp_get_temp interface public, export it and also export the
ab8500_btemp_get, ab8500_btemp_get_batctrl_temp interfaces, so that the
ab8500 hwmon driver can use them.
Signed-off-by: Hongbo Zhang <hongbo.zhang@linaro.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
|
|
|
|
This is a dependency for mxs/multiplatform
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
drivers/clocksource/Makefile
|
|
Provides support for 1801 variant of stmpe gpio port expanders.
This chip has 18 gpios configurable as GPI, GPO, keypad matrix,
special key or dedicated key function.
Note that special/dedicated key function is not supported yet.
Signed-off-by: Jean-Nicolas Graux <jean-nicolas.graux@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
syscon.h header uses struct device_node in functions' declarations
without declaring it. This causes compilation warnings like:
include/linux/mfd/syscon.h:20: warning: ‘struct device_node’
declared inside parameter list
include/linux/mfd/syscon.h:20: warning: its scope is only this
definition or declaration, which is probably not what you want
Fix it by adding a forward declaration of struct device_node.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The enum is missing the definition for the first bit, which makes all
the rest off by one. Add definition for the TPS65090_IRQ_INTERRUPT bit
which at 0.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
is_palmas_charger checks for the presence of charging
functionality in the device
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Ian Lartey <ian@slimlogic.co.uk>
Acked-by: Laxman Dewangani <ldewangan@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson
MFD portions of the ux500 multiplatform branch.
A second tag for the ARM SoC tree will build upon
this one. This mainly removes the header file
dependencies from the PRCMU driver in the MFD
subsystem, and moves the PM functions to the
machine.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
If a GPIO is specified for the chip IRQ line then request it. This
improves support for systems that do not put pins into input mode when
used as interrupts.
Also use this GPIO when the primary IRQ is in edge triggered mode to
detect if we have handled pending interrupts in order to improve
robustness.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Allow the user to configure edge triggered IRQs, though we do not yet
fully handle new interrupts occurring while an interrupt is being handled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This untangles the final bits of the prcmu code from the platform
code:
* The IRQ_PRCMU_* definitions move from irqs-db8500.h into prcmu.c
because they are only of local significance.
* u8500_thsens_device goes into the prcmu, because it uses a PRCMU
IRQ that the platform does not see.
* IRQ_DB8500_AB8500 and IRQ_PRCMU_BASE go into the platform data
because the PRCMU does not see it.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[Fixed a oneliner bug]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We are trying to decompose and decentralize the code in
the DB8500 PRCMU out into subdrivers. The code moved in
this patch concerns a group of functions used for
decoupling and recoupling the IRQs from the GIC. During
sleep and idle the Ux500 system will transfer all IRQ
handling to the PRCMU using these functions.
Basically we are left with the two alternatives of code
placement as:
- arch/arm/mach-ux500/pm.c - this because the code is
closely related to the GIC, and takes ownership of
some of the registers from the PRCMU related to this
PM functionality.
- drivers/mfd/db8500-prcmu-pm.c - because the code is
affecting stuff in the PRCMU register range. But then
this code needs to remap and handle GIC registers.
This patch implementation is taking the first approach.
Currently the cpuidle driver is the only piece of code
using this set of functions, but it will later also be
used by the suspend/resume code which is currently under
review.
The header file is moved to:
<linux/platform_data/arm-ux500-pm.h>
The function prototypes need to be placed in a globally
visible header since the CPUidle code is planned to move
out to drivers/cpuidle.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Rickard Andersson <rickard.andersson@stericsson.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch will make an early remapping of the PRCMU, to be
used when setting up the clocks, that will call down into parts
of the PRCMU driver before it is probed.
Going forward this will be removed like this:
- The mailbox subsystem need to be merged.
http://marc.info/?l=linux-kernel&m=136314559201983&w=2
- At this point the PRCMU clock code can be moved over to the
ux500 clock driver in drivers/clk/ux500/* and maintained
there in a decentralized manner.
- This early initcall and PRCMU base parameters become part of
the ux500_clk_init() call instead.
Cc: Suman Anna <s-anna@ti.com>
Cc: Loic Pallardy <loic.pallardy@st.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.linaro.org/people/ljones/linux-3.0-ux500
Conflicts:
drivers/mfd/ab8500-gpadc.c
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch allow using syscon driver from the platform data, i.e.
possibility using driver on systems without oftree support.
For search syscon device from the client drivers,
"syscon_regmap_lookup_by_pdevname" function was added.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This is the base EC implementation, which provides a high level
interface to the EC for use by the rest of the kernel. The actual
communcations is dealt with by a separate protocol driver which
registers itself with this interface.
Interrupts are passed on through a notifier.
A simple message structure is used to pass messages to the
protocol driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Jonathan Kliegman <kliegs@chromium.org>
Signed-off-by: Luigi Semenzato <semenzato@chromium.org>
Signed-off-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This file is included verbatim from the ChromeOS EC respository.
Ideally we would prefer to avoid changing it, to make it easier
to track this rapidly-changing file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc into char-misc-next
Mark writes:
extcon: arizona: Updates for v3.10
There's a bunch of different things in this series, I can split them out
if need be:
- Support for configuring the button detection circuit to reflect the
accessories supplied with the system.
- Improvements in the HPDET based detection scheme.
- Additional robustness against more pathological use cases.
- A few small standalone fixes.
|
|
Regulator platform data is now passed though a single structure
as opposed to the old way where four separate struct elements
were required. This patch makes use of the new format.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Help mitigate against mechanical bounce during the initial detection by
allowing the configuration of an additional debounce on top of that the
hardware does during the initial phase of microphone detection operation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Rather than measuring both HP channels we can simply directly measure the
microphone impedance and then rely on MICDET for final confirmation of the
presence of a suitable microphone. This improves the overall performance
of the identification process.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
In some designs an external pull won't be needed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The Arizona button detection circuit is configurable, allowing the system
integrator to program a range of thresholds for the buttons supported on
the accessory but currently the driver uses the default button ranges and
does not provide any flexibility in how this is exposed to the application
layer.
Provide platform data allowing the user to control this and to map
the buttons to keys in the input subsystem.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg Kroah-Hartman:
"Here are some small char/misc driver fixes that resolve issues
recently reported against the 3.9-rc kernels. All have been in
linux-next for a while."
* tag 'char-misc-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
VMCI: Fix process-to-process DRGAMs.
mei: ME hardware reset needs to be synchronized
mei: add mei_stop function to stop mei device
extcon: max77693: Initialize register of MUIC device to bring up it without platform data
extcon: max77693: Fix bug of wrong pointer when platform data is not used
extcon: max8997: Check the pointer of platform data to protect null pointer error
|
|
This picks up the MEI fixes that we need in this branch now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc into asoc-arizona
ASoC/extcon: arizona: Fix interaction between HPDET and headphone outputs
This patch series covers both ASoC and extcon subsystems and fixes an
interaction between the HPDET function and the headphone outputs - we
really shouldn't run HPDET while the headphone is active. The first
patch is a refactoring to make the extcon side easier.
|
