| Age | Commit message (Collapse) | Author |
|---|
|
The mac address is already stored in the sprom structure by the
platform code of the SoC this Ethernet core is found on, it just has to
be fetched from this structure instead of accessing the nvram here.
This patch also adds a return value to indicate if a mac address could
be fetched from the sprom structure.
When CONFIG_SSB_DRIVER_GIGE is not set the header file now also declares
ssb_gige_get_macaddr().
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Michael Buesch <m@bues.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Amir Vadai says:
====================
This series from Yan Burman adds support for unicast MAC address filtering and
ndo FDB operations. It also includes some optimizations to loopback related
decisions and checks in the TX/RX fast path and one cleanup, all in separate
patches.
Today, when adding macvlan devices, the NIC goes into promiscuous mode, since
unicast MAC filtering is not supported. With these changes, macvlan devices can
be added without the penalty of promiscuous mode.
If for some reason adding a unicast address filter fails e.g as of missing space in
the HW mac table, the device forces itself into promiscuous mode (and out of this
forced state when enough space is available).
Also, now it is possible to have bridge under multi-function configuration that include
PF and VFs. In order to use bridge over PF/VFs, VM MAC fdb entries must be added e.g.
using 'bridge fdb add' command.
Changes from v1 - based on more comments from Eric Dumazet:
* added failure handling when adding unicast address filter
Changes from v0 - based on comments from Eric Dumazet:
* Removed unneeded synchronize_rcu()
* Use kfree_rcu() instead of synchronize_rcu() + kfree()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move low level code that deals with management of Ethernet MACs and QPs from mlx4_core to mlx4_en.
Also convert the new functions to deal with MACs in form of char array instead of u64.
Actual functions moved:
mlx4_replace_mac
mlx4_get_eth_qp
mlx4_put_eth_qp
To conduct this change, some functionality had to be exported from the core,
the following functions were added:
mlx4_get_base_qp
__mlx4_replace_mac (low level function for CX1/A0 compatibility)
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setting up IPv6 addresses on configurations with many macvlans
is not really working, as many multicast messages are dropped.
Add a multicast filter to macvlan to reduce the amount of cloned
skbs and overhead.
Successfully tested with 1024 macvlans on one ethernet device.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_gso_segment() is almost always called in tx path,
except for openvswitch. It calls this function when
it receives the packet and tries to queue it to user-space.
In this special case, the ->ip_summed check inside
skb_gso_segment() is no longer true, as ->ip_summed value
has different meanings on rx path.
This patch adjusts skb_gso_segment() so that we can at least
avoid such warnings on checksum.
Cc: Jesse Gross <jesse@nicira.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some modes don't require any special carrier handling so
in these cases, the kernel can control the carrier as for
any other interface. However, some other modes, e.g. lacp,
requires more than just that, so userspace needs to control
the carrier itself.
The daemon today is ready to control it, but the kernel
still can change it based on events.
This fix so that either kernel or userspace is controlling
the carrier.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
adding support for VLAN interface for cpsw.
CPSW VLAN Capability
* Can filter VLAN packets in Hardware
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ivan Vercera was recently backporting commit
9c13cb8bb477a83b9a3c9e5a5478a4e21294a760 to a RHEL kernel, and I noticed that,
while this patch protects the tg3 driver from having its ndo_poll_controller
routine called during device initalization, it does nothing for the driver
during shutdown. I.e. it would be entirely possible to have the
ndo_poll_controller method (or subsequently the ndo_poll) routine called for a
driver in the netpoll path on CPU A while in parallel on CPU B, the ndo_close or
ndo_open routine could be called. Given that the two latter routines tend to
initizlize and free many data structures that the former two rely on, the result
can easily be data corruption or various other crashes. Furthermore, it seems
that this is potentially a problem with all net drivers that support netpoll,
and so this should ideally be fixed in a common path.
As Ben H Pointed out to me, we can't preform dev_open/dev_close in atomic
context, so I've come up with this solution. We can use a mutex to sleep in
open/close paths and just do a mutex_trylock in the napi poll path and abandon
the poll attempt if we're locked, as we'll just retry the poll on the next send
anyway.
I've tested this here by flooding netconsole with messages on a system whos nic
driver I modfied to periodically return NETDEV_TX_BUSY, so that the netpoll tx
workqueue would be forced to send frames and poll the device. While this was
going on I rapidly ifdown/up'ed the interface and watched for any problems.
I've not found any.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Ivan Vecera <ivecera@redhat.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Ben Hutchings <bhutchings@solarflare.com>
CC: Francois Romieu <romieu@fr.zoreil.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TCP Appropriate Byte Count was added by me, but later disabled.
There is no point in maintaining it since it is a potential source
of bugs and Linux already implements other better window protection
heuristics.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/intel/e1000e/ethtool.c
drivers/net/vmxnet3/vmxnet3_drv.c
drivers/net/wireless/iwlwifi/dvm/tx.c
net/ipv6/route.c
The ipv6 route.c conflict is simple, just ignore the 'net' side change
as we fixed the same problem in 'net-next' by eliminating cached
neighbours from ipv6 routes.
The e1000e conflict is an addition of a new statistic in the ethtool
code, trivial.
The vmxnet3 conflict is about one change in 'net' removing a guarding
conditional, whilst in 'net-next' we had a netdev_info() conversion.
The iwlwifi conflict is dealing with a WARN_ON() conversion in
'net-next' vs. a revert happening in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Paul Gortmaker says:
====================
The removal of wanrouter code was originally listed in the (now
gone) feature removal file since May 2012, and an RFC of the
deletion was posted[1] in late 2012. The overall concept was given
an OK, but defconfig contamination, build failures, etc. meant that
it didn't quite make it into mainline for 3.8.
Since that time, Dan discovered (via code audit) a runtime bug that
proves nobody has been using this for over four years[2]. With that
new information, I think it makes sense for someone to follow through
on Joe's original RFC and get this done for the 3.9 release.
In addition to resolving the build failures of the RFC by keeping
stub headers, this also splits the change into two parts, just like
the token ring removal did. Part #1 decouples the mainline kernel
from the expired subsystem, and part #2 does the large scale
deletion of the subsystem content.
The advantage of the above, is that a "git blame" will never lead
you to a 4000+ line deletion commit. The large scale deletion will
never show up in a "git blame" and hence the same advantages that we
get from the "--irreversible-delete" in the review stage of "git
format-patch" are also embedded into the git history itself. This
may seem like a moot point to some, but for those who spend a
considerable amount of time data mining in the git history, this is
probably worth doing.
I have done build tests of all[mod/yes]config for both the stage 1
(Makefile and Kconfig) and stage 2 (full driver delete) as a sanity
check, and the issues with the previously posted RFC should be gone.
Speaking of "--irreversible-delete" -- these patches were created
with that option, so if you want to use them locally, you are going
to have to pull (location below) the content instead of doing a
"git am" of the mailed out content.
[1] http://patchwork.ozlabs.org/patch/198794/
[2] http://www.spinics.net/lists/netdev/msg218670.html
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The wanrouter support was identified earlier as unused for years,
and so the previous commit totally decoupled it from the kernel,
leaving the related wanrouter files present, but totally inert.
Here we take the final step in that cleanup, by doing a wholesale
removal of these files. The two step process is used so that the
large deletion is decoupled from the git history of files that we
still care about.
The drivers deleted here all were dependent on the Kconfig setting
CONFIG_WAN_ROUTER_DRIVERS.
A stub wanrouter.h header (kernel & uapi) are left behind so that
drivers/isdn/i4l/isdn_x25iface.c continues to compile, and so that
we don't accidentally break userspace that expected these defines.
Cc: Joe Perches <joe@perches.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Mac reassignments should only be done when not supported by the firmware. To
accomplish that, checking firmware capability bit to know whether we should
reassign macs in the driver.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A device sending 0 length frames as fast as it can has been
observed killing the host system due to the resulting memory
pressure.
Temporarily disable RX skb allocation and URB submission when
the current error ratio is high, preventing us from trying to
allocate an infinite number of skbs. Reenable as soon as we
are finished processing the done queue, allowing the device
to continue working after short error bursts.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bring in the 'net' tree so that we can get some ipv4/ipv6 bug
fixes that some net-next work will build upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are some usecase when lifetime of ipv4 addresses might be helpful.
For example:
1) initramfs networkmanager uses a DHCP daemon to learn network
configuration parameters
2) initramfs networkmanager addresses, routes and DNS configuration
3) initramfs networkmanager is requested to stop
4) initramfs networkmanager stops all daemons including dhclient
5) there are addresses and routes configured but no daemon running. If
the system doesn't start networkmanager for some reason, addresses and
routes will be used forever, which violates RFC 2131.
This patch is essentially a backport of ivp6 address lifetime mechanism
for ipv4 addresses.
Current "ip" tool supports this without any patch (since it does not
distinguish between ipv4 and ipv6 addresses in this perspective.
Also, this should be back-compatible with all current netlink users.
Reported-by: Pavel Šimerda <psimerda@redhat.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Summary of changes:
.Newly added phys
-KSZ8081/KSZ8091, which has some phy ids.
-KSZ8061
-KSZ9031, which is Gigabit phy.
-KSZ886X, which has a switch function.
-KSZ8031, which has a same phy ids with KSZ8021.
Signed-off-by: David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev->npinfo is protected by RCU.
This fixes the following sparse warnings:
net/core/netpoll.c:177:48: error: incompatible types in comparison expression (different address spaces)
net/core/netpoll.c:200:35: error: incompatible types in comparison expression (different address spaces)
net/core/netpoll.c:221:35: error: incompatible types in comparison expression (different address spaces)
net/core/netpoll.c:327:18: error: incompatible types in comparison expression (different address spaces)
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next
John W. Linville says:
====================
Included is an NFC pull. Samuel says:
"It brings the following goodies:
- LLCP socket timestamping (To be used e.g with the recently released nfctool
application for a more efficient skb timestamping when sniffing).
- A pretty big pn533 rework from Waldemar, preparing the driver to support
more flavours of pn533 based devices.
- HCI changes from Eric in preparation for the microread driver support.
- Some LLCP memory leak fixes, cleanups and slight improvements.
- pn544 and nfcwilink move to the devm_kzalloc API.
- An initial Secure Element (SE) API.
- An nfc.h license change from the original author, allowing non GPL
application code to safely include it."
Also included are a pair of mac80211 pulls. Johannes says:
"We found two bugs in the previous code, so I'm sending you a pull
request again this soon.
This contains two regulatory bug fixes, some of Thomas's hwsim beacon
timer work and a documentation fix from Bob."
"Another pull request for mac80211-next. This time, I have a number of
things, the patches are mostly self-explanatory. There are a few fixes
from Felix and myself, and random cleanups & improvements. The biggest
thing is the partial patchset from Marco preparing for mesh powersave."
Additionally, there are a pair of iwlwifi pulls. Johannes says:
"For iwlwifi-next, I have a few cleanups/improvements as well as a few
not very important fixes and more preparations for new devices."
"Please pull a few updates for iwlwifi. These are just some cleanups and
a debug improvement."
On top of that, there is a slew of driver updates. This includes
brcmfmac, mwifiex, ath9k, carl9170, and mwl8k as well as a handful
of others. The bcma and ssb busses get some attention as well.
Still, I don't see any big headliners here.
Also included is a pull of the wireless tree, in order to resolve
some merge conflicts.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added accessor and skb_reserve helpers for struct can_skb_priv.
Removed pointless skb_headroom() check.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
CC: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD fixes from Samuel Ortiz:
"This is the first pull request for MFD fixes for 3.8
We have some build failure fixes (twl4030, vexpress, abx500 and
tps65910), some actual runtime oops and lockup fixes (rtsx, da9052),
and some more hypothetical NULL pointers dereferences fixes for
pcf50633 and max776xx.
Then we also have additional rtsx fixes for a correct switch output
voltage and clock divider correctness for rtl8411 (rtsx driver), and
irqdomain fix for db8550-prcmu, and some more cosmetic fixes for
arizona and wm5102."
* tag 'mfd-for-linus-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: rtsx: Fix oops when rtsx_pci_sdmmc is not probed
mfd: wm5102: Fix definition of WM5102_MAX_REGISTER
mfd: twl4030: Don't warn about uninitialized return code
mfd: da9052/53 lockup fix
mfd: rtsx: Add clock divider hook
mmc: rtsx: Call MFD hook to switch output voltage
mfd: rtsx: Add output voltage switch hook
mfd: Fix compile errors and warnings when !CONFIG_AB8500_BM
mfd: vexpress: Export global functions to fix build error
mfd: arizona: Check errors from regcache_sync()
mfd: tc3589x: Use simple irqdomain
mfd: pcf50633: Init pcf->dev before using it
mfd: max77693: Init max77693->dev before using it
mfd: max77686: Init max77686->dev before using it
mfd: db8500-prcmu: Fix irqdomain usage
mfd: tps65910: Select REGMAP_IRQ in Kconfig to fix build error
mfd: arizona: Disable control interface reporting for WM5102 and WM5110
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
|
|
Pull networking updates from David Miller:
"Much more accumulated than I would have liked due to an unexpected
bout with a nasty flu:
1) AH and ESP input don't set ECN field correctly because the
transport head of the SKB isn't set correctly, fix from Li
RongQing.
2) If netfilter conntrack zones are disabled, we can return an
uninitialized variable instead of the proper error code. Fix from
Borislav Petkov.
3) Fix double SKB free in ath9k driver beacon handling, from Felix
Feitkau.
4) Remove bogus assumption about netns cleanup ordering in
nf_conntrack, from Pablo Neira Ayuso.
5) Remove a bogus BUG_ON in the new TCP fastopen code, from Eric
Dumazet. It uses spin_is_locked() in it's test and is therefore
unsuitable for UP.
6) Fix SELINUX labelling regressions added by the tuntap multiqueue
changes, from Paul Moore.
7) Fix CRC errors with jumbo frame receive in tg3 driver, from Nithin
Nayak Sujir.
8) CXGB4 driver sets interrupt coalescing parameters only on first
queue, rather than all of them. Fix from Thadeu Lima de Souza
Cascardo.
9) Fix regression in the dispatch of read/write registers in dm9601
driver, from Tushar Behera.
10) ipv6_append_data miscalculates header length, from Romain KUNTZ.
11) Fix PMTU handling regressions on ipv4 routes, from Steffen
Klassert, Timo Teräs, and Julian Anastasov.
12) In 3c574_cs driver, add necessary parenthesis to "x << y & z"
expression. From Nickolai Zeldovich.
13) macvlan_get_size() causes underallocation netlink message space,
fix from Eric Dumazet.
14) Avoid division by zero in xfrm_replay_advance_bmp(), from Nickolai
Zeldovich. Amusingly the zero check was already there, we were
just performing it after the modulus :-)
15) Some more splice bug fixes from Eric Dumazet, which fix things
mostly eminating from how we now more aggressively use high-order
pages in SKBs.
16) Fix size calculation bug when freeing hash tables in the IPSEC
xfrm code, from Michal Kubecek.
17) Fix PMTU event propagation into socket cached routes, from Steffen
Klassert.
18) Fix off by one in TX buffer release in netxen driver, from Eric
Dumazet.
19) Fix rediculous memory allocation requirements introduced by the
tuntap multiqueue changes, from Jason Wang.
20) Remove bogus AMD platform workaround in r8169 driver that causes
major problems in normal operation, from Timo Teräs.
21) virtio-net set affinity and select queue don't handle
discontiguous cpu numbers properly, fix from Wanlong Gao.
22) Fix a route refcounting issue in loopback driver, from Eric
Dumazet. There's a similar fix coming that we might add to the
macvlan driver as well.
23) Fix SKB leaks in batman-adv's distributed arp table code, from
Matthias Schiffer.
24) r8169 driver gives descriptor ownership back the hardware before
we're done reading the VLAN tag out of it, fix from Francois
Romieu.
25) Checksums not calculated properly in GRE tunnel driver fix from
Pravin B Shelar.
26) Fix SCTP memory leak on namespace exit."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (101 commits)
dm9601: support dm9620 variant
SCTP: Free the per-net sysctl table on net exit. v2
net: phy: icplus: fix broken INTR pin settings
net: phy: icplus: Use the RGMII interface mode to configure clock delays
IP_GRE: Fix kernel panic in IP_GRE with GRE csum.
sctp: set association state to established in dupcook_a handler
ip6mr: limit IPv6 MRT_TABLE identifiers
r8169: fix vlan tag read ordering.
net: cdc_ncm: use IAD provided by the USB core
batman-adv: filter ARP packets with invalid MAC addresses in DAT
batman-adv: check for more types of invalid IP addresses in DAT
batman-adv: fix skb leak in batadv_dat_snoop_incoming_arp_reply()
net: loopback: fix a dst refcounting issue
virtio-net: reset virtqueue affinity when doing cpu hotplug
virtio-net: split out clean affinity function
virtio-net: fix the set affinity bug when CPU IDs are not consecutive
can: pch_can: fix invalid error codes
can: ti_hecc: fix invalid error codes
can: c_can: fix invalid error codes
r8169: remove the obsolete and incorrect AMD workaround
...
|
|
Pravin Shelar mentioned that GSO could potentially generate
wrong TX checksum if skb has fragments that are overwritten
by the user between the checksum computation and transmit.
He suggested to linearize skbs but this extra copy can be
avoided for normal tcp skbs cooked by tcp_sendmsg().
This patch introduces a new SKB_GSO_SHARED_FRAG flag, set
in skb_shinfo(skb)->gso_type if at least one frag can be
modified by the user.
Typical sources of such possible overwrites are {vm}splice(),
sendfile(), and macvtap/tun/virtio_net drivers.
Tested:
$ netperf -H 7.7.8.84
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to
7.7.8.84 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.00 3959.52
$ netperf -H 7.7.8.84 -t TCP_SENDFILE
TCP SENDFILE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 7.7.8.84 ()
port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.00 3216.80
Performance of the SENDFILE is impacted by the extra allocation and
copy, and because we use order-0 pages, while the TCP_STREAM uses
bigger pages.
Reported-by: Pravin Shelar <pshelar@nicira.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marc Kleine-Budde says:
====================
this is a pull-request for net-next/master. There is are 9 patches by
Fabio Baltieri and Kurt Van Dijck which add LED infrastructure and
support for CAN devices. Bernd Krumboeck adds a driver for the USB CAN
adapter from 8 devices. Oliver Hartkopp improves the CAN gateway
functionality. There are 4 patches by me, which clean up the CAN's
Kconfig.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
This batch contains netfilter updates for you net-next tree, they are:
* The new connlabel extension for x_tables, that allows us to attach
labels to each conntrack flow. The kernel implementation uses a
bitmask and there's a file in user-space that maps the bits with the
corresponding string for each existing label. By now, you can attach
up to 128 overlapping labels. From Florian Westphal.
* A new round of improvements for the netns support for conntrack.
Gao feng has moved many of the initialization code of each module
of the netns init path. He also made several code refactoring, that
code looks cleaner to me now.
* Added documentation for all possible tweaks for nf_conntrack via
sysctl, from Jiri Pirko.
* Cisco 7941/7945 IP phone support for our SIP conntrack helper,
from Kevin Cernekee.
* Missing header file in the snmp helper, from Stephen Hemminger.
* Finally, a couple of fixes to resolve minor issues with these
changes, from myself.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An issue has been reported where the PMIC either locks up or fails to
respond following a system Reset. This could result in a second write
in which the bus writes the current content of the write buffer to address
of the last I2C access.
The failure case is where this unwanted write transfers incorrect data to
a critical register.
This patch fixes this issue to by following any read or write with a dummy read
to a safe register address. A safe register address is one where the contents
will not affect the operation of the system.
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Add callback function conv_clk_and_div_n to convert between SSC clock
and its divider N.
For rtl8411, the formula to calculate SSC clock divider N is different
with the other card reader models.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Different card reader has different method to switch output voltage,
add this callback to let the card reader implement its individual switch
function.
This is needed as rtl8411 has a specific switch output voltage procedure.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The struct can_skb_priv is used to transport additional information along
with the stored struct can(fd)_frame that can not be contained in existing
struct sk_buff elements.
can_skb_priv is located in the skb headroom, which does not touch the existing
CAN sk_buff usage with skb->data and skb->len, so that even out-of-tree
CAN drivers can be used without changes.
Btw. out-of-tree CAN drivers without can_skb_priv in the sk_buff headroom
would not support features based on can_skb_priv.
The can_skb_priv->ifindex contains the first interface where the CAN frame
appeared on the local host. Unfortunately skb->skb_iif can not be used as this
value is overwritten in every netif_receive_skb() call.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The LED trigger name for CAN devices is based on the initial
CAN device name, but does never change. The LED trigger name
is not guaranteed to be unique in case of hotplugging CAN devices.
This patch tries to address this problem by modifying the
LED trigger name according to the CAN device name when
the latter changes.
v1 - Kurt Van Dijck
v2 - Fabio Baltieri
- remove rename blocking if trigger is bound
- use led-subsystem function for the actual rename (still WiP)
- call init/exit functions from dev.c
v3 - Kurt Van Dijck
- safe operation for non-candev based devices (vcan, slcan)
based on earlier patch
v4 - Kurt Van Dijck
- trivial patch mistakes fixed
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In net_device notifier calls, it was impossible to determine
if a CAN device is based on candev in a safe way.
This patch adds such test in order to access candev storage
from within those notifiers.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch implements the functions to add two LED triggers, named
<ifname>-tx and <ifname>-rx, to a canbus device driver.
Triggers are called from specific handlers by each CAN device driver and
can be disabled altogether with a Kconfig option.
The implementation keeps the LED on when the interface is UP and blinks
the LED on network activity at a configurable rate.
This only supports can-dev based drivers, as it uses some support field
in the can_priv structure.
Supported drivers should call devm_can_led_init() and can_led_event() as
needed.
Cleanup is handled automatically by devres, so no *_exit function is
needed.
Supported events are:
- CAN_LED_EVENT_OPEN: turn on tx/rx LEDs
- CAN_LED_EVENT_STOP: turn off tx/rx LEDs
- CAN_LED_EVENT_TX: trigger tx LED blink
- CAN_LED_EVENT_RX: trigger tx LED blink
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's a long-pending fixes pull request for arm-soc (I didn't send
one in the -rc4 cycle).
The larger deltas are from:
- A fixup of error paths in the mvsdio driver
- Header file move for a driver that hadn't been properly converted
to multiplatform on i.MX, which was causing build failures when
included
- Device tree updates for at91 dealing mostly with their new pinctrl
setup merged in 3.8 and mistakes in those initial configs
The rest are the normal mix of small fixes all over the place; sunxi,
omap, imx, mvebu, etc, etc."
* tag 'fixes-for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (40 commits)
mfd: vexpress-sysreg: Don't skip initialization on probe
ARM: vexpress: Enable A7 cores in V2P-CA15_A7's Device Tree
ARM: vexpress: extend the MPIDR range used for pen release check
ARM: at91/dts: correct comment in at91sam9x5.dtsi for mii
ARM: at91/at91_dt_defconfig: add at91sam9n12 SoC to DT defconfig
ARM: at91/at91_dt_defconfig: remove memory specification to cmdline
ARM: at91/dts: add macb mii pinctrl config for kizbox
ARM: at91: rm9200: remake the BGA as default version
ARM: at91: fix gpios on i2c-gpio for RM9200 DT
ARM: at91/at91sam9x5 DTS: add SCK USART pins
ARM: at91/at91sam9x5 DTS: correct wrong PIO BANK values on u(s)arts
ARM: at91/at91-pinctrl documentation: fix typo and add some details
ARM: kirkwood: fix missing #interrupt-cells property
mmc: mvsdio: use devm_ API to simplify/correct error paths.
clk: mvebu/clk-cpu.c: fix memory leakage
ARM: OMAP2+: omap4-panda: add UART2 muxing for WiLink shared transport
ARM: OMAP2+: DT node Timer iteration fix
ARM: OMAP2+: Fix section warning for omap_init_ocp2scp()
ARM: OMAP2+: fix build break for omapdrm
ARM: OMAP2: Fix missing omap2xxx_clkt_vps_late_init function calls
...
|
|
Definitions and macros for implementing soreusport.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Minimal omap fixes for the -rc series:
- A build fix for recently merged omap DRM changes
- Regression fixes from the common clock framework conversion
for omap4 audio and omap2 reboot
- Regression fix for pandaboard WLAN control UART muxing caused by
u-boot only muxing essential pins nowadays
- Timer iteration fix for CONFIG_OF_DYNAMIC
- A section mismatch fix for ocp2scp init
* tag 'omap-for-v3.8-rc4/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (306 commits)
ARM: OMAP2+: omap4-panda: add UART2 muxing for WiLink shared transport
ARM: OMAP2+: DT node Timer iteration fix
ARM: OMAP2+: Fix section warning for omap_init_ocp2scp()
ARM: OMAP2+: fix build break for omapdrm
ARM: OMAP2: Fix missing omap2xxx_clkt_vps_late_init function calls
ARM: OMAP4: hwmod_data: Correct IDLEMODE for McPDM
ARM: OMAP4: clock data: Lock ABE DPLL on all revisions
+ Linux 3.8-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libata fixes from Jeff Garzik:
1) ahci: Fix typo that caused erronenous error handling.
Thought: I wonder if sparse could have caught this, somehow.
2) ahci: support a slightly odd Enmotus variant
3) core: fix a drive detection problem by correcting the logic by which
the DevSlp timing variables are obtained and used.
* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] replace sata_settings with devslp_timing
[libata] ahci: Add support for Enmotus Bobcat device.
[libata] ahci: Fix lack of command retry after a success error handler.
|
|
Cleanup and preparation for the next change.
signal_wake_up(resume => true) is overused. None of ptrace/jctl callers
actually want to wakeup a TASK_WAKEKILL task, but they can't specify the
necessary mask.
Turn signal_wake_up() into signal_wake_up_state(state), reintroduce
signal_wake_up() as a trivial helper, and add ptrace_signal_wake_up()
which adds __TASK_TRACED.
This way ptrace_signal_wake_up() can work "inside" ptrace_request()
even if the tracee doesn't have the TASK_WAKEKILL bit set.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
drivers/mfd/ab8500-core.c:1015:21: error: ‘ab8500_bm_data’ undeclared here
include/linux/mfd/abx500/ab8500-bm.h:445:13: warning: ‘ab8500_fg_reinit’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:448:13: warning: ‘ab8500_charger_usb_state_changed’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:451:29: warning: ‘ab8500_btemp_get’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:455:12: warning: ‘ab8500_btemp_get_batctrl_temp’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:463:12: warning: ‘ab8500_fg_inst_curr_blocking’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:442:12: warning: ‘ab8500_fg_inst_curr_done’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:447:26: warning: ‘ab8500_fg_get’ defined but not used
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
fixes
From Sascha Hauer:
ARM i.MX fixes for -rc.
This contains a single compilation fix for the CODA driver.
* tag 'imx-fixes-rc' of git://git.pengutronix.de/git/imx/linux-2.6:
[media] coda: Fix build due to iram.h rename
|
|
We do have some USB net devices, which cannot do ARP.
so we can introduce a new flag FLAG_NOARP, then client drivers
can easily handle this kind of devices
Signed-off-by: Wei Shuai <cpuwolf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we set mac address, software mac address in system and hardware mac
address all need to be updated. Current eth_mac_addr() doesn't allow
callers to implement error handling nicely.
This patch split eth_mac_addr() to prepare part and real commit part,
then we can prepare first, and try to change hardware address, then do
the real commit if hardware address is set successfully.
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This will ease further addition of new MRT[6]_* values and avoid to update
in6.h each time.
Note that we reduce the maximum value from 210 to 209, but 210 does not match
any known value in ip[6]_mroute_setsockopt().
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module fixes and a virtio block fix from Rusty Russell:
"Various minor fixes, but a slightly more complex one to fix the
per-cpu overload problem introduced recently by kvm id changes."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
module: put modules in list much earlier.
module: add new state MODULE_STATE_UNFORMED.
module: prevent warning when finit_module a 0 sized file
virtio-blk: Don't free ida when disk is in use
|
|
The ia64 function "thread_matches()" has no users since commit
e868a55c2a8c ("[IA64] remove find_thread_for_addr()"). Remove it.
This allows us to make ptrace_check_attach() static to kernel/ptrace.c,
which is good since we'll need to change the semantics of it and fix up
all the callers.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Most SIP devices use a source port of 5060/udp on SIP requests, so the
response automatically comes back to port 5060:
phone_ip:5060 -> proxy_ip:5060 REGISTER
proxy_ip:5060 -> phone_ip:5060 100 Trying
The newer Cisco IP phones, however, use a randomly chosen high source
port for the SIP request but expect the response on port 5060:
phone_ip:49173 -> proxy_ip:5060 REGISTER
proxy_ip:5060 -> phone_ip:5060 100 Trying
Standard Linux NAT, with or without nf_nat_sip, will send the reply back
to port 49173, not 5060:
phone_ip:49173 -> proxy_ip:5060 REGISTER
proxy_ip:5060 -> phone_ip:49173 100 Trying
But the phone is not listening on 49173, so it will never see the reply.
This patch modifies nf_*_sip to work around this quirk by extracting
the SIP response port from the Via: header, iff the source IP in the
packet header matches the source IP in the SIP request.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- cpuidle regression fix related to the initialization of state
kobjects from Krzysztof Mazur.
- cpuidle fix removing some not very useful code and making some
user-visible problems go away at the same time. From Daniel Lezcano.
- ACPI build fix from Yinghai Lu.
* tag 'pm+acpi-for-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: remove the power_specified field in the driver
ACPI / glue: Fix build with ACPI_GLUE_DEBUG set
cpuidle: fix number of initialized/destroyed states
|
|
Commit 1b963c81b145 ("lockdep, rwsem: provide down_write_nest_lock()")
contains a bug in a codepath when CONFIG_DEBUG_LOCK_ALLOC is disabled,
which causes down_read() to be called instead of down_write() by mistake
on such configurations. Fix that.
Reported-and-tested-by: Andrew Clayton <andrew@digital-domain.net>
Reported-and-tested-by: Zlatko Calusic <zlatko.calusic@iskon.hr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If the default iosched is built as module, the kernel may deadlock
while trying to load the iosched module on device probe if the probing
was running off async. This is because async_synchronize_full() at
the end of module init ends up waiting for the async job which
initiated the module loading.
async A modprobe
1. finds a device
2. registers the block device
3. request_module(default iosched)
4. modprobe in userland
5. load and init module
6. async_synchronize_full()
Async A waits for modprobe to finish in request_module() and modprobe
waits for async A to finish in async_synchronize_full().
Because there's no easy to track dependency once control goes out to
userland, implementing properly nested flushing is difficult. For
now, make module init perform async_synchronize_full() iff module init
has queued async jobs as suggested by Linus.
This avoids the described deadlock because iosched module doesn't use
async and thus wouldn't invoke async_synchronize_full(). This is
hacky and incomplete. It will deadlock if async module loading nests;
however, this works around the known problem case and seems to be the
best of bad options.
For more details, please refer to the following thread.
http://thread.gmane.org/gmane.linux.kernel/1420814
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Alex Riesen <raa.lkml@gmail.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Alex Riesen <raa.lkml@gmail.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
