summaryrefslogtreecommitdiff
path: root/include/video/omapdss.h
AgeCommit message (Collapse)Author
2012-01-26OMAPDSS: HDMI: PHY burnout fixTomi Valkeinen
A hardware bug in the OMAP4 HDMI PHY causes physical damage to the board if the HDMI PHY is kept powered on when the cable is not connected. This patch solves the problem by adding hot-plug-detection into the HDMI IP driver. This is not a real HPD support in the sense that nobody else than the IP driver gets to know about the HPD events, but is only meant to fix the HW bug. The strategy is simple: If the display device is turned off by the user, the PHY power is set to OFF. When the display device is turned on by the user, the PHY power is set either to LDOON or TXON, depending on whether the HDMI cable is connected. The reason to avoid PHY OFF when the display device is on, but the cable is disconnected, is that when the PHY is turned OFF, the HDMI IP is not "ticking" and thus the DISPC does not receive pixel clock from the HDMI IP. This would, for example, prevent any VSYNCs from happening, and would thus affect the users of omapdss. By using LDOON when the cable is disconnected we'll avoid the HW bug, but keep the HDMI working as usual from the user's point of view. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-01-05OMAPDSS: HDMI: Disable DDC internal pull upMythri P K
Disables the internal pull resistor for SDA and SCL which are enabled by default, as there are external pull up's in 4460 and 4430 ES2.3 SDP, Blaze and Panda Boards, It is done to avoid the EDID read failure. Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@linaro.org> Signed-off-by: Mythri P K <mythripk@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-01-05OMAPDSS: HDMI: Move duplicate code from boardfileMythri P K
Move duplicate HDMI mux_init code from omap4 and panda board file to display file. Signed-off-by: Mythri P K <mythripk@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02OMAPDSS: Add comments about blocking of ovl/mgr functionsTomi Valkeinen
Add comments specifying what ovl/mgr functions may block. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02OMAPDSS: APPLY: remove device_changed fieldTomi Valkeinen
omap_overlay_manager contains device_changed field, which no longer has any use. So remove the field and the few places where it is touched. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02OMAPDSS: APPLY: move channel-field to extra_info setTomi Valkeinen
Setting overlay's output channel is currently handled at the same time as other overlay attributes. This is not right, as the normal attributes should only affect one overlay and manager, but changing the channel affects two managers. This patch moves the channel field into the "extra_info" set, handled together with enabled-status. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02OMAPDSS: APPLY: move ovl->info to apply.cTomi Valkeinen
struct omap_overlayr contains info and info_dirty fields, both of which should be internal to apply.c. This patch moves those fields into ovl_priv data, and names them user_info and user_info_dirty. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02OMAPDSS: APPLY: move mgr->info to apply.cTomi Valkeinen
struct omap_overlay_manager contains info and info_dirty fields, both of which should be internal to apply.c. This patch moves those fields into mgr_priv data, and names them user_info and user_info_dirty. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02OMAPDSS: APPLY: rewrite overlay enable/disableTomi Valkeinen
Overlays are currently enabled and disabled with a boolean in the struct omap_overlay_info. The overlay info is set with ovl->set_overlay_info(), and made into use with mgr->apply(). This doesn't work properly, as the enable/disable status may affect also other overlays, for example when using fifo-merge. Thus the enabling and disabling of the overlay needs to be done outside the normal overlay configuration. This patch achieves that by doing the following things: 1) Add function pointers to struct omap_overlay: enable(), disable() and is_enabled(). These are used to do the obvious. The functions may block. 2) Move the "enabled" field from struct omap_overlay to ovl_priv_data. 3) Add a new route for settings to be applied to the HW, called "extra_info". The status of the normal info and extra_info are tracked separately. The point here is to allow the normal info to be changed and applied in non-blocking matter, whereas the extra_info can only be changed when holding the mutex. This makes it possible to, for example, set the overlay enable flag, apply it, and wait until the HW has taken the flag into use. This is not possible if the enable flag would be in the normal info, as a new value for the flag could be set at any time from the users of omapdss. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02OMAPDSS: APPLY: move mgr->enabled to mgr_priv_dataTomi Valkeinen
struct omap_overlay_manager contains "enabled"-field, used to track if the manager is enabled or not. This field should be internal to apply.c. This patch moves the field to mgr_priv_data, and applies the necessary locking when accessing the field. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02OMAPDSS: DSI: call mgr_enable/disable for cmd mode displaysTomi Valkeinen
The current code uses dsi_video_mode_enable/disable functions to enable/disable DISPC output for video mode displays. For command mode displays we have no notion in the DISPC side of whether the panel is enabled, except when a dss_mgr_start_update() call is made. However, to properly maintain the DISPC state in apply.c, we need to know if a manager used for a manual update display is currently in use. This patch achieves that by changing dsi_video_mode_enable/disable to dsi_enable/disable_video_output, which is called by both video and command mode displays. For video mode displays it starts the actual pixel stream, as it did before. For command mode displays it doesn't do anything else than mark that the manager is currently in use. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02OMAPDSS: store overlays in a list for each managerTomi Valkeinen
Current way of handling overlay-manager links is a bit strange: each manager has a static array, containing pointers to all the overlays (even those used by other managers). The overlays contain a pointer to the manager being used. This patch makes the system a bit saner: each manager has a linked list of overlays, and only the overlays linked to that manager are in the list. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02OMAPDSS: store managers in an arrayTomi Valkeinen
Overlay managers are stored in a linked list. There's no need for this list, as an array would do just as fine. This patch changes the code to use an array for overlay managers. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02OMAPDSS: APPLY: track whether a manager is enabledTomi Valkeinen
Add "enabled" field to struct omap_overlay_manager, which tells if the output is enabled or not. This will be used in apply.c in the following patches. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02OMAPDSS: hide manager's enable/disable()Tomi Valkeinen
omap_overlay_manager struct contains enable() and disable() functions. However, these are only meant to be used from inside omapdss, and thus it's bad to expose the functions. This patch adds dss_mgr_enable() and dss_mgr_disable() functions to apply.c, which handle enabling and disabling the output. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-12-02OMAPDSS: remove partial update from DSITomi Valkeinen
Partial update for manual update displays has never worked quite well: * The HW has limitations on the update area, and the x and width need to be even. * Showing a part of a scaled overlay causes artifacts. * Makes the management of dispc very complex Considering the above points and the fact that partial update is not used anywhere, this and the following patches remove the partial update support. This will greatly simplify the following re-write of the apply mechanism to get proper locking and additional features like fifo-merge. This patch removes the partial update from the dsi.c. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-11-08ARM: OMAP: HWMOD: Unify DSS resets for OMAPsTomi Valkeinen
This patch adds a custom DSS reset function used on OMAPs from OMAP2 forward. The function doesn't actually do a reset, it only waits for the reset to complete. The reason for this is that on OMAP4 there is no possibility to do a SW reset, and on OMAP2/3 doing a SW reset for dss_core resets all the other DSS modules also, thus breaking the HWMOD model where every DSS module is handled independently. This fixes the problem with DSS reset on OMAP4, caused by the fact that because there's no SW reset for dss_core on OMAP4, the HWMOD framework doesn't try to reset dss_core and thus the DSS clocks were never enabled at the same time. This causes causes the HWMOD reset to fail for dss_dispc and dss_rfbi. The common reset function will also allow us to fix another problem in the future: before doing a reset we need to disable DSS outputs, which are in some cases enabled by the bootloader, as otherwise DSS HW seems to get more or less stuck, requiring a power reset to recover. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> [paul@pwsan.com: modified to build arch/arm/mach-omap2/display.o unconditionally to avoid an error when !CONFIG_OMAP2_DSS] Signed-off-by: Paul Walmsley <paul@pwsan.com>
2011-10-03OMAPDSS: DISPC: zorder support for DSS overlaysArchit Taneja
Add zorder support on OMAP4, this feature allows deciding the visibility order of the overlays based on the zorder value provided as an overlay info parameter or a sysfs attribute of the overlay object. Use the overlay cap OMAP_DSS_OVL_CAP_ZORDER to determine whether zorder is supported for the overlay or not. Use dss feature FEAT_ALPHA_FREE_ZORDER if the caps are not available. Ensure that all overlays that are enabled and connected to the same manager have different zorders. Swapping zorders of 2 enabled overlays currently requires disabling one of the overlays. Signed-off-by: Archit Taneja <archit@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-10-03OMAPDSS: DISPC: VIDEO3 pipeline supportArchit Taneja
Add support for VIDEO3 pipeline on OMAP4: - Add VIDEO3 pipeline information in dss_features and omapdss.h - Add VIDEO3 pipeline register coefficients in dispc.h - Create a new overlay structure corresponding to VIDEO3. - Make changes in dispc.c for VIDEO3 Signed-off-by: Archit Taneja <archit@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-10-03OMAPDSS/OMAP_VOUT: Fix incorrect OMAP3-alpha compatibility settingArchit Taneja
On OMAP3, in order to enable alpha blending for LCD and TV managers, we needed to set LCDALPHABLENDERENABLE/TVALPHABLENDERENABLE bits in DISPC_CONFIG. On OMAP4, alpha blending is always enabled by default, if the above bits are set, we switch to an OMAP3 compatibility mode where the zorder values in the pipeline attribute registers are ignored and a fixed priority is configured. Rename the manager_info member "alpha_enabled" to "partial_alpha_enabled" for more clarity. Introduce two dss_features FEAT_ALPHA_FIXED_ZORDER and FEAT_ALPHA_FREE_ZORDER which represent OMAP3-alpha compatibility mode and OMAP4 alpha mode respectively. Introduce an overlay cap for ZORDER. The DSS2 user is expected to check for the ZORDER cap, if an overlay doesn't have this cap, the user is expected to set the parameter partial_alpha_enabled. If the overlay has ZORDER cap, the DSS2 user can assume that alpha blending is already enabled. Don't support OMAP3 compatibility mode for now. Trying to read/write to alpha_blending_enabled sysfs attribute issues a warning for OMAP4 and does not set the LCDALPHABLENDERENABLE/TVALPHABLENDERENABLE bits. Change alpha_enabled to partial_alpha_enabled in the omap_vout driver. Use overlay cap "OMAP_DSS_OVL_CAP_GLOBAL_ALPHA" to check if overlay supports alpha blending or not. Replace this with checks for VIDEO1 pipeline. Cc: linux-media@vger.kernel.org Cc: Lajos Molnar <molnar@ti.com> Signed-off-by: Archit Taneja <archit@ti.com> Acked-by: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30OMAPDSS: remove vaddr from overlay infoTomi Valkeinen
overlay_info struct, used to configure overlays, currently includes both physical and virtual addresses for the pixels. The vaddr was added to support more exotic configurations where CPU would be used to update a display, but it is not currently used and there has been no interest in the feature. Using CPU to update a screen is also less interesting now that OMAP4 has two LCD outputs. This patch removes the vaddr field, and modifies the users of omapdss accordingly. This makes the use of omapdss a bit simpler, as the user doesn't need to think if it needs to give the vaddr. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30OMAP: DSS2: add detect() to omap_dss_driver structTomi Valkeinen
detect() can be used to probe if the display is connected. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30OMAP: DSS2: add read_edid() to omap_dss_driver structTomi Valkeinen
read_edid() can be used to get the EDID information from the display. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30OMAP: DSS2: DISPC: Add missing IRQ definitionsTomi Valkeinen
Add IRQ definitions for missing OMAP4 IRQs: FRAMEDONEWB, FRAMEDONETV, WBBUFFEROVERFLOW. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30OMAP: DSS2: DSI: Add comment about regnTomi Valkeinen
regn divider is one greater than the REGN divider in TRM. Add a comment to point this out. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30OMAP: DSS2: HDMI: change regn definitionTomi Valkeinen
regn divider is currently programmed to the registers without change, but when calculating clock frequencies it is used as regn+1. To make this similar to how DSI handles the dividers this patch changes the regn value to be used as such for calculations, but the value programmed to registers is regn-1. This simplifies the clock frequency calculations, makes it similar to DSI, and also allows us to use regn value 0 as undefined. Cc: Mythri P K <mythripk@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30OMAP: DSS2: DSI Video mode supportArchit Taneja
Add initial support for DSI video mode panels: - Add a new structure omap_dss_dsi_videomode_data in the member "panel" in omap_dss_device struct. This allows panel driver to configure dsi video_mode specific parameters. - Configure basic DSI video mode timing parameters: HBP, HFP, HSA, VBP, VFP, VSA, TL and VACT. - Configure DSI protocol engine registers for video_mode support. - Introduce functions dsi_video_mode_enable() and dsi_video_mode_disable() which enable/disable video mode for a given virtual channel and a given pixel format type. Things left for later - Add functions to check for errors in video mode timings provided by panel. - Configure timing registers required for command mode interleaving. Signed-off-by: Archit Taneja <archit@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30OMAP: DSS2: Create an enum for DSI pixel formatsArchit Taneja
Currently, DSI pixel info is only represented by the pixel size in bits using the pixel_size parameter in omap_dss_device struct's ctrl member. This is not sufficient information for DSI video mode usage, as two of the supported formats(RGB666 loosely packed, and RGB888) have the same pixel container size, but different data_type values for the video mode packet header. Create enum "omap_dss_dsi_pixel_format" which describes the pixel data format the panel is configured for. Create helper function dsi_get_pixel_size() which returns the pixel size of the given pixel format. Modify functions omapdss_default_get_recommended_bpp() and dss_use_replication() to use dsi_get_pixel_size(). Signed-off-by: Archit Taneja <archit@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30OMAP: DSS2: DSI: Introduce generic read functionsArchit Taneja
Introduce read functions which use generic Processor-to-Peripheral transaction types. These are needed by some devices which may not support corresponding DCS commands. Add function dsi_vc_generic_send_read_request() which can send a short packet with 0, 1 or 2 bytes of request data and the corresponding generic data type. Rename function dsi_vc_dcs_read_rx_fifo() to dsi_vc_read_rx_fifo() and modify it to take the enum "dss_dsi_content_type" as an argument to use either DCS or GENERIC Peripheral-to-Processor transaction types while parsing data read from the device. Signed-off-by: Archit Taneja <archit@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30OMAP: DSS2: DSI: Remove functions dsi_vc_dcs_read_1() and dsi_vc_dcs_read_2()Archit Taneja
Remove functions dsi_vc_dcs_read_1() and dsi_vc_dcs_read_2(), these are used when the panel is expected to return 1 and 2 bytes respecitvely. This was manily used for debugging purposes. These functions should be implemented in the panel driver if needed. Signed-off-by: Archit Taneja <archit@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30OMAP: DSS2: DSI: Introduce generic write functionsArchit Taneja
Intoduce enum "dss_dsi_content_type" to differentiate between DCS and generic content types. Introduce short and long packet write functions which use generic Processor-to-Peripheral transaction types. These are needed by some devices which may not support corresponding DCS commands. Create common write functions which allow code reuse between DCS and generic write functions. Signed-off-by: Archit Taneja <archit@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30OMAP: DSS2: Create enum for DSI operation modesArchit Taneja
Create an enum for DSI operation modes, use this to set the capabilities of the device in dsi_init_display(). Signed-off-by: Archit Taneja <archit@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30OMAP: DSS2: Add GLOBAL_ALPHA & PRE_MULT_ALPHA to ovl capsTomi Valkeinen
Add OMAP_DSS_OVL_CAP_GLOBAL_ALPHA and OMAP_DSS_OVL_CAP_PRE_MULT_ALPHA to overlay capabilities. Use these instead of FEAT_GLOBAL_ALPHA, FEAT_GLOBAL_ALPHA_VID1 and FEAT_PRE_MULT_ALPHA in code. Remove FEAT_GLOBAL_ALPHA_VID1 and FEAT_PRE_MULT_ALPHA which are no longer used. FEAT_GLOBAL_ALPHA is still used to decide if the HW has global alpha register. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by: Archit Taneja <archit@ti.com>
2011-09-30OMAP: DSS2: Remove support for non-DISPC overlaysTomi Valkeinen
Remove support for non-DISPC overlays and overlay managers. The support to possibly have non-DISPC overlays and managers was made to make it possible to use CPU and/or sDMA to update RFBI or DSI command mode displays. It is ok to remove the support, because: - No one has used the feature. - Display update without DISPC is very slow, so it is debatable if the update would even be usable. - Removal cleans up code. - If such a feature is needed later, it is better implemented outside omapdss driver. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by: Archit Taneja <archit@ti.com>
2011-09-30OMAP: DSS2: Handle manager change in applyTomi Valkeinen
Currently when changing the manager of an overlay, set_manager() directly calls dispc to set the overlay's destination. Change this to be more in line with other overlay configurations, and this will also remove the need to have dispc clocks enabled when calling set_manager(). A new field is added to overlay struct, "manager_changed". This is similar to "display_changed" field in manager struct, and is used to inform apply that the manager has changed and thus write to the registers is needed. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-09-30OMAP: DSS2: DSI: Improve dsi_mux_pads parametersTomi Valkeinen
dsi_mux_pads() needs to know about the DSI HW module and the DSI lanes used. Split the function into two, enable and disable, which take necessary arguments, and add empty implementations for both. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-07-25OMAP: DSS2: Remove unused opt_clock_availableTomi Valkeinen
opt_clock_available() is no longer needed, so remove it. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-07-25OMAP: DSS2: rewrite use of context_loss_countTomi Valkeinen
The function to get device's context loss count has changed from omap_pm_get_last_off_on_transaction_id() to omap_pm_get_dev_context_loss_count() Change name of the function pointer in omapdss.h accordingly, and use the term "context loss count" instead of "context id" in the code. Restructure the context loss count functions to handle errors properly, and ensure that context is always considered lost if an error happens. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-07-01OMAP: DSS2: Add Color Phase Rotation supportTomi Valkeinen
Add Color Phase Rotation (CPR) support and sysfs files to enable CPR and to set the CPR coefficient matrix. CPR is enabled via manager?/cpr_enable file, and the coefficient matrix is set via manager?/cpr_coef file. The values in cpr_coef are in the following order: RR RG RB GR GG GB BR BG BB Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-07-01OMAP: DSS2: remove update_mode from omapdssTomi Valkeinen
Remove the whole update_mode stuff from omapdss driver. If automatic update for manual update displays is needed, it's better implemented in higher layers. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-07-01OMAP: DSS2: remove extra includes from include/video/omapdss.hTomi Valkeinen
omapdss.h included platform_device.h and atomic.h, neither of which is needed by omapdss.h. Remove those includes from omapdss.h, and fix the affected .c files which did not include platform_device.h even though they should. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-23OMAP: DSS2: Add support for NV12 formatAmber Jain
Add the support for NV12 color format. Configure base address for UV component of NV12 color format. Change the way chroma scaling is handled for YUV formats on OMAP4 by enabling chroma-resampling for video pipeline and hence using FIR2 register set for scaling UV. Changes to _dispc_set_scaling(), because of the reason above, are: - call _dispc_set_scaling_common() to handle scaling for all color formats except for OMAP4 where it only handles scaling for RGB or Y-component - call _dispc_set_scaling_uv() for special handling required for UV component on OMAP4. - dispc_set_scaling_uv() also resets chroma-resampling bit for RGB color modes. Contains chroma scaling (_dispc_set_scaling_uv) design and implemented by Lajos Molnar <molnar@ti.com> Signed-off-by: Amber Jain <amber@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-23OMAP: DSS2: Add new color formats for OMAP4Amber Jain
Add new color formats supported by OMAP4: NV12, RGBA16, RGBX16, ARGB16_1555, XRGB16_1555. NV12 color format is defined here, its support in DSS will be added separately. Signed-off-by: Amber Jain <amber@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-16OMAP: DSS2: DSI: Get number of DSI data lanes using DSI_GNQ registerArchit Taneja
On OMAP3, the DSI module has 2 data lanes. On OMAP4, DSI1 has 4 data lanes and DSI2 has 2 data lanes. Introduce function dsi_get_num_data_lanes() which returns the number of data lanes on the dsi interface, introduce function dsi_get_num_data_lanes_dssdev() which returns the number of data lanes used by the omap_dss_device connected to the lanes. Use the DSI_GNQ register on OMAP4 to get the number of data lanes, modify dsi.c to use the number of lanes and the extra data lanes on DSI1. Signed-off-by: Archit Taneja <archit@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-12OMAP: DSS2: RFBI: add omap_rfbi_configureTomi Valkeinen
Add omap_rfbi_configure() which the panel driver can use to reconfigure the data element size and the number of data lines in the RFBI bus. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-12OMAP: DSS2: RFBI: add rfbi_bus_lockTomi Valkeinen
Add similar bus lock to RFBI as is in DSI. The panel driver can use the bus lock to mark that the RFBI bus is currently in use. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-12OMAP4: DSS2: DSI: Changes for DSI2 on OMAP4Archit Taneja
Introduce DSI2 PLL clock sources needed by LCD2 channel and DSI2 Protocol engine and DISPC Functional clock. Do the following: - Modify dss_get_dsi_clk_source() and dss_select_dsi_clk_source() to take the dsi module number as an argument. - Create debugfs files for dsi2, split the corresponding debugfs functions. - Allow DPI to use these new clock sources. Signed-off-by: Archit Taneja <archit@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-12OMAP: DSS2: Pass platform_device as an argument in dsi functionsArchit Taneja
The DSI interface is represented as a platform device, using the DSI platform driver(dsi.c). The current DSI driver design is capable of running only one instance of a DSI device. On OMAP4, there are 2 very similar DSI modules which can be represented as instances of "omapdss_dsi" platform device. Add member "module" in "dssdev.phy.dsi" that tells us which DSI module's lanes the panel is connected to. Modify dsi.c functions to take the device's platform_device struct pointer, provide functions dsi_get_dsidev_from_dssdev() and dsi_get_dsidev_from_id() take the panel's omap_dss_device and module number respectively, and return the platform_device pointer. Currently, the dsi struct is declared globally and is accessed when dsi data is needed. The new pdev argument will be used later to provide the platform device's dsi related data. Signed-off-by: Archit Taneja <archit@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-12OMAP: DSS2: DSI: Add extra omap_dss_device argument in functions exported by dsiArchit Taneja
Add pointer to omap_dss_device struct as an argument in the functions which are exported to dsi panel drivers. This argument will tell the DSI driver which DSI interface's data it has to choose. Signed-off-by: Archit Taneja <archit@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-05-11OMAP: DSS2: DSI: Add DSI pad muxing supportTomi Valkeinen
Add dsi_mux_pads function pointer to omap_dss_board_info, and use the function pointer in DSI code to configure the DSI pads either to normal DSI operation, or to pull down when in ULPS. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>