| Age | Commit message (Collapse) | Author |
|---|
|
Merge misc patches from Andrew Morton:
- the "misc" tree - stuff from all over the map
- checkpatch updates
- fatfs
- kmod changes
- procfs
- cpumask
- UML
- kexec
- mqueue
- rapidio
- pidns
- some checkpoint-restore feature work. Reluctantly. Most of it
delayed a release. I'm still rather worried that we don't have a
clear roadmap to completion for this work.
* emailed from Andrew Morton <akpm@linux-foundation.org>: (78 patches)
kconfig: update compression algorithm info
c/r: prctl: add ability to set new mm_struct::exe_file
c/r: prctl: extend PR_SET_MM to set up more mm_struct entries
c/r: procfs: add arg_start/end, env_start/end and exit_code members to /proc/$pid/stat
syscalls, x86: add __NR_kcmp syscall
fs, proc: introduce /proc/<pid>/task/<tid>/children entry
sysctl: make kernel.ns_last_pid control dependent on CHECKPOINT_RESTORE
aio/vfs: cleanup of rw_copy_check_uvector() and compat_rw_copy_check_uvector()
eventfd: change int to __u64 in eventfd_signal()
fs/nls: add Apple NLS
pidns: make killed children autoreap
pidns: use task_active_pid_ns in do_notify_parent
rapidio/tsi721: add DMA engine support
rapidio: add DMA engine support for RIO data transfers
ipc/mqueue: add rbtree node caching support
tools/selftests: add mq_perf_tests
ipc/mqueue: strengthen checks on mqueue creation
ipc/mqueue: correct mq_attr_ok test
ipc/mqueue: improve performance of send/recv
selftests: add mq_open_tests
...
|
|
When we do restore we would like to have a way to setup a former
mm_struct::exe_file so that /proc/pid/exe would point to the original
executable file a process had at checkpoint time.
For this the PR_SET_MM_EXE_FILE code is introduced. This option takes a
file descriptor which will be set as a source for new /proc/$pid/exe
symlink.
Note it allows to change /proc/$pid/exe if there are no VM_EXECUTABLE
vmas present for current process, simply because this feature is a special
to C/R and mm::num_exe_file_vmas become meaningless after that.
To minimize the amount of transition the /proc/pid/exe symlink might have,
this feature is implemented in one-shot manner. Thus once changed the
symlink can't be changed again. This should help sysadmins to monitor the
symlinks over all process running in a system.
In particular one could make a snapshot of processes and ring alarm if
there unexpected changes of /proc/pid/exe's in a system.
Note -- this feature is available iif CONFIG_CHECKPOINT_RESTORE is set and
the caller must have CAP_SYS_RESOURCE capability granted, otherwise the
request to change symlink will be rejected.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
During checkpoint we dump whole process memory to a file and the dump
includes process stack memory. But among stack data itself, the stack
carries additional parameters such as command line arguments, environment
data and auxiliary vector.
So when we do restore procedure and once we've restored stack data itself
we need to setup mm_struct::arg_start/end, env_start/end, so restored
process would be able to find command line arguments and environment data
it had at checkpoint time. The same applies to auxiliary vector.
For this reason additional PR_SET_MM_(ARG_START | ARG_END | ENV_START |
ENV_END | AUXV) codes are introduced.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Vagin <avagin@openvz.org>
Cc: Serge Hallyn <serge.hallyn@canonical.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Vasiliy Kulikov <segoon@openwall.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
While doing the checkpoint-restore in the user space one need to determine
whether various kernel objects (like mm_struct-s of file_struct-s) are
shared between tasks and restore this state.
The 2nd step can be solved by using appropriate CLONE_ flags and the
unshare syscall, while there's currently no ways for solving the 1st one.
One of the ways for checking whether two tasks share e.g. mm_struct is to
provide some mm_struct ID of a task to its proc file, but showing such
info considered to be not that good for security reasons.
Thus after some debates we end up in conclusion that using that named
'comparison' syscall might be the best candidate. So here is it --
__NR_kcmp.
It takes up to 5 arguments - the pids of the two tasks (which
characteristics should be compared), the comparison type and (in case of
comparison of files) two file descriptors.
Lookups for pids are done in the caller's PID namespace only.
At moment only x86 is supported and tested.
[akpm@linux-foundation.org: fix up selftests, warnings]
[akpm@linux-foundation.org: include errno.h]
[akpm@linux-foundation.org: tweak comment text]
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Andrey Vagin <avagin@openvz.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Glauber Costa <glommer@parallels.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Vasiliy Kulikov <segoon@openwall.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Valdis.Kletnieks@vt.edu
Cc: Michal Marek <mmarek@suse.cz>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A cleanup of rw_copy_check_uvector and compat_rw_copy_check_uvector after
changes made to support CMA in an earlier patch.
Rather than having an additional check_access parameter to these
functions, the first paramater type is overloaded to allow the caller to
specify CHECK_IOVEC_ONLY which means check that the contents of the iovec
are valid, but do not check the memory that they point to. This is used
by process_vm_readv/writev where we need to validate that a iovec passed
to the syscall is valid but do not want to check the memory that it points
to at this point because it refers to an address space in another process.
Signed-off-by: Chris Yeoh <yeohc@au1.ibm.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
eventfd_ctx->count is an __u64 counter which is allowed to reach
ULLONG_MAX. eventfd_write() adds a __u64 value to "count", but the kernel
side eventfd_signal() only adds an int value to it. Make them consistent.
[akpm@linux-foundation.org: update interface documentation]
Signed-off-by: Sha Zhengju <handai.szj@taobao.com>
Cc: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Adds DMA Engine framework support into RapidIO subsystem.
Uses DMA Engine DMA_SLAVE interface to generate data transfers to/from
remote RapidIO target devices.
Introduces RapidIO-specific wrapper for prep_slave_sg() interface with an
extra parameter to pass target specific information.
Uses scatterlist to describe local data buffer. Address flat data buffer
on a remote side.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit b231cca4381e ("message queues: increase range limits") changed
mqueue default value when attr parameter is specified NULL from hard
coded value to fs.mqueue.{msg,msgsize}_max sysctl value.
This made large side effect. When user need to use two mqueue
applications 1) using !NULL attr parameter and it require big message
size and 2) using NULL attr parameter and only need small size message,
app (1) require to raise fs.mqueue.msgsize_max and app (2) consume large
memory size even though it doesn't need.
Doug Ledford propsed to switch back it to static hard coded value.
However it also has a compatibility problem. Some applications might
started depend on the default value is tunable.
The solution is to separate default value from maximum value.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Acked-by: Doug Ledford <dledford@redhat.com>
Acked-by: Joe Korty <joe.korty@ccur.com>
Cc: Amerigo Wang <amwang@redhat.com>
Acked-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Mqueue limitation is slightly naieve parameter likes other ipcs because
unprivileged user can consume kernel memory by using ipcs.
Thus, too aggressive raise bring us security issue. Example, current
setting allow evil unprivileged user use 256GB (= 256 * 1024 * 1024*1024)
and it's enough large to system will belome unresponsive. Don't do that.
Instead, every admin should adjust the knobs for their own systems.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Doug Ledford <dledford@redhat.com>
Acked-by: Joe Korty <joe.korty@ccur.com>
Cc: Amerigo Wang <amwang@redhat.com>
Acked-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit b231cca4381e ("message queues: increase range limits") changed the
maximum size of a message in a message queue from INT_MAX to 8192*128.
Unfortunately, we had customers that relied on a size much larger than
8192*128 on their production systems. After reviewing POSIX, we found
that it is silent on the maximum message size. We did find a couple other
areas in which it was not silent. Fix up the mqueue maximums so that the
customer's system can continue to work, and document both the POSIX and
real world requirements in ipc_namespace.h so that we don't have this
issue crop back up.
Also, commit 9cf18e1dd74cd0 ("ipc: HARD_MSGMAX should be higher not lower
on 64bit") fiddled with HARD_MSGMAX without realizing that the number was
intentionally in place to limit the msg queue depth to one that was small
enough to kmalloc an array of pointers (hence why we divided 128k by
sizeof(long)). If we wish to meet POSIX requirements, we have no choice
but to change our allocation to a vmalloc instead (at least for the large
queue size case). With that, it's possible to increase our allowed
maximum to the POSIX requirements (or more if we choose).
[sfr@canb.auug.org.au: using vmalloc requires including vmalloc.h]
Signed-off-by: Doug Ledford <dledford@redhat.com>
Cc: Serge E. Hallyn <serue@us.ibm.com>
Cc: Amerigo Wang <amwang@redhat.com>
Cc: Joe Korty <joe.korty@ccur.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit b231cca4381e ("message queues: increase range limits") changed
how we create a queue that does not include an attr struct passed to
open so that it creates the queue with whatever the maximum values are.
However, if the admin has set the maximums to allow flexibility in
creating a queue (aka, both a large size and large queue are allowed,
but combined they create a queue too large for the RLIMIT_MSGQUEUE of
the user), then attempts to create a queue without an attr struct will
fail. Switch back to using acceptable defaults regardless of what the
maximums are.
Note: so far, we only know of a few applications that rely on this
behavior (specifically, set the maximums in /proc, then run the
application which calls mq_open() without passing in an attr struct, and
the application expects the newly created message queue to have the
maximum sizes that were set in /proc used on the mq_open() call, and all
of those applications that we know of are actually part of regression
test suites that were coded to do something like this:
for size in 4096 65536 $((1024 * 1024)) $((16 * 1024 * 1024)); do
echo $size > /proc/sys/fs/mqueue/msgsize_max
mq_open || echo "Error opening mq with size $size"
done
These test suites that depend on any behavior like this are broken. The
concept that programs should rely upon the system wide maximum in order
to get their desired results instead of simply using a attr struct to
specify what they want is fundamentally unfriendly programming practice
for any multi-tasking OS.
Fixing this will break those few apps that we know of (and those app
authors recognize the brokenness of their code and the need to fix it).
However, the following patch "mqueue: separate mqueue default value"
allows a workaround in the form of new knobs for the default msg queue
creation parameters for any software out there that we don't already
know about that might rely on this behavior at the moment.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Cc: Serge E. Hallyn <serue@us.ibm.com>
Cc: Amerigo Wang <amwang@redhat.com>
Cc: Joe Korty <joe.korty@ccur.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since commit b231cca4381e ("message queues: increase range limits") on
Oct 18, 2008, calls to mq_open() that did not pass in an attribute
struct and expected to get default values for the size of the queue and
the max message size now get the system wide maximums instead of
hardwired defaults like they used to get.
This was uncovered when one of the earlier patches in this patch set
increased the default system wide maximums at the same time it increased
the hard ceiling on the system wide maximums (a customer specifically
needed the hard ceiling brought back up, the new ceiling that commit
b231cca4381e introduced was too low for their production systems). By
increasing the default maximums and not realising they were tied to any
attempt to create a message queue without an attribute struct, I had
inadvertently made it such that all message queue creation attempts
without an attribute struct were failing because the new default
maximums would create a queue that exceeded the default rlimit for
message queue bytes.
As a result, the system wide defaults were brought back down to their
previous levels, and the system wide ceilings on the maximums were
raised to meet the customer's needs. However, the fact that the no
attribute struct behavior of mq_open() could be broken by changing the
system wide maximums for message queues was seen as fundamentally broken
itself. So we hardwired the no attribute case back like it used to be.
But, then we realized that on the very off chance that some piece of
software in the wild depended on that behavior, we could work around
that issue by adding two new knobs to /proc that allowed setting the
defaults for message queues created without an attr struct separately
from the system wide maximums.
What is not an option IMO is to leave the current behavior in place. No
piece of software should ever rely on setting the system wide maximums
in order to get a desired message queue. Such a reliance would be so
fundamentally multitasking OS unfriendly as to not really be tolerable.
Fortunately, we don't know of any software in the wild that uses this
except for a regression test program that caught the issue in the first
place. If there is though, we have made accommodations with the two new
/proc knobs (and that's all the accommodations such fundamentally broken
software can be allowed)..
This patch:
The various defines for minimums and maximums of the sysctl controllable
mqueue values are scattered amongst different files and named
inconsistently. Move them all into ipc_namespace.h and make them have
consistent names. Additionally, make the number of queues per namespace
also have a minimum and maximum and use the same sysctl function as the
other two settable variables.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Acked-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Amerigo Wang <amwang@redhat.com>
Cc: Joe Korty <joe.korty@ccur.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add userspace definitions, guard all relevant kernel structures. While at
it document stuff and remove now useless userspace hint.
It is easy to add the relevant system call to respective libc's, but it
seems pointless to have to duplicate the data structures.
This is based on the kexec-tools headers, with the exception of just using
int on return (succes or failure) and using size_t instead of 'unsigned
long int' for the number of segments argument of kexec_load().
Signed-off-by: maximilian attems <max@stro.at>
Cc: Simon Horman <horms@verge.net.au>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Haren Myneni <hbabu@us.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Many architectures clear tasks' mm_cpumask like this:
read_lock(&tasklist_lock);
for_each_process(p) {
if (p->mm)
cpumask_clear_cpu(cpu, mm_cpumask(p->mm));
}
read_unlock(&tasklist_lock);
Depending on the context, the code above may have several problems,
such as:
1. Working with task->mm w/o getting mm or grabing the task lock is
dangerous as ->mm might disappear (exit_mm() assigns NULL under
task_lock(), so tasklist lock is not enough).
2. Checking for process->mm is not enough because process' main
thread may exit or detach its mm via use_mm(), but other threads
may still have a valid mm.
This patch implements a small helper function that does things
correctly, i.e.:
1. We take the task's lock while whe handle its mm (we can't use
get_task_mm()/mmput() pair as mmput() might sleep);
2. To catch exited main thread case, we use find_lock_task_mm(),
which walks up all threads and returns an appropriate task
(with task lock held).
Also, Per Peter Zijlstra's idea, now we don't grab tasklist_lock in
the new helper, instead we take the rcu read lock. We can do this
because the function is called after the cpu is taken down and marked
offline, so no new tasks will get this cpu set in their mm mask.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 8f92054e7ca1 ("CRED: Fix __task_cred()'s lockdep check and banner
comment"):
add the following validation condition:
task->exit_state >= 0
to permit the access if the target task is dead and therefore
unable to change its own credentials.
OK, but afaics currently this can only help wait_task_zombie() which calls
__task_cred() without rcu lock.
Remove this validation and change wait_task_zombie() to use task_uid()
instead. This means we do rcu_read_lock() only to shut up the lockdep,
but we already do the same in, say, wait_task_stopped().
task_is_dead() should die, task->exit_state != 0 means that this task has
passed exit_notify(), only do_wait-like code paths should use this.
Unfortunately, we can't kill task_is_dead() right now, it has already
acquired buggy users in drivers/staging. The fix already exists.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If we move call_usermodehelper_fns() to kmod.c file and EXPORT_SYMBOL it
we can avoid exporting all it's helper functions:
call_usermodehelper_setup
call_usermodehelper_setfns
call_usermodehelper_exec
And make all of them static to kmod.c
Since the optimizer will see all these as a single call site it will
inline them inside call_usermodehelper_fns(). So we loose the call to
_fns but gain 3 calls to the helpers. (Not that it matters)
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
call_usermodehelper_freeinfo() is not used outside of kmod.c. So unexport
it, and make it static to kmod.c
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is patchset makes fatfs stop using the VFS '->write_super()' method
for writing out the FSINFO block.
The final goal is to get rid of the 'sync_supers()' kernel thread. This
kernel thread wakes up every 5 seconds (by default) and calls
'->write_super()' for all mounted file-systems. And the bad thing is that
this is done even if all the superblocks are clean. Moreover, some
file-systems do not even need this end they do not register the
'->write_super()' method at all (e.g., btrfs).
So 'sync_supers()' most often just generates useless wake-ups and wastes
power. I am trying to make all file-systems independent of
'->write_super()' and plan to remove 'sync_supers()' and '->write_super'
completely once there are no more users.
The '->write_supers()' method is mostly used by baroque file-systems like
hfs, udf, etc. Modern file-systems like btrfs and xfs do not use it.
This justifies removing this stuff from VFS completely and make every FS
self-manage own superblock.
Tested with xfstests.
This patch:
Preparation for further changes. It introduces a special inode
('fsinfo_inode') in FAT file-system which we'll later use for managing the
FSINFO block. Note, this there is already one special inode ('fat_inode')
which is used for managing the FAT tables.
Introduce new 'MSDOS_FSINFO_INO' constant for this special inode. It is
safe to do because FAT file-system does not store inode numbers on the
media but generates them run-time.
I've also cleaned up the comment to existing 'MSDOS_ROOT_INO' constant,
while on it.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Previous code was using optimizations which were developed to work well
even on narrow-word CPUs (by today's standards). But Linux runs only on
32-bit and wider CPUs. We can use that.
First: using 32x32->64 multiply and trivial 32-bit shift, we can correctly
divide by 10 much larger numbers, and thus we can print groups of 9 digits
instead of groups of 5 digits.
Next: there are two algorithms to print larger numbers. One is generic:
divide by 1000000000 and repeatedly print groups of (up to) 9 digits.
It's conceptually simple, but requires an (unsigned long long) /
1000000000 division.
Second algorithm splits 64-bit unsigned long long into 16-bit chunks,
manipulates them cleverly and generates groups of 4 decimal digits. It so
happens that it does NOT require long long division.
If long is > 32 bits, division of 64-bit values is relatively easy, and we
will use the first algorithm. If long long is > 64 bits (strange
architecture with VERY large long long), second algorithm can't be used,
and we again use the first one.
Else (if long is 32 bits and long long is 64 bits) we use second one.
And third: there is a simple optimization which takes fast path not only
for zero as was done before, but for all one-digit numbers.
In all tested cases new code is faster than old one, in many cases by 30%,
in few cases by more than 50% (for example, on x86-32, conversion of
12345678). Code growth is ~0 in 32-bit case and ~130 bytes in 64-bit
case.
This patch is based upon an original from Michal Nazarewicz.
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Douglas W Jones <jones@cs.uiowa.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
ULONG_MAX is often used to check for integer overflow when calculating
allocation size. While ULONG_MAX happens to work on most systems, there
is no guarantee that `size_t' must be the same size as `long'.
This patch introduces SIZE_MAX, the maximum value of `size_t', to improve
portability and readability for allocation size validation.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Acked-by: Alex Elder <elder@dreamhost.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull battery updates from Anton Vorontsov:
"A bunch of fixes for v3.5, nothing extraordinary."
* tag 'for-v3.5' of git://git.infradead.org/battery-2.6: (27 commits)
smb347-charger: Include missing <linux/err.h>
smb347-charger: Clean up battery attributes
max17042_battery: Add support for max17047/50 chip
sbs-battery.c: Capacity attr = remaining relative capacity
isp1704_charger: Use after free on probe error
ds2781_battery: Use DS2781_PARAM_EEPROM_SIZE and DS2781_USER_EEPROM_SIZE
power_supply: Fix a typo in BATTERY_DS2781 Kconfig entry
charger-manager: Provide cm_notify_event function for in-kernel use
charger-manager: Poll battery health in normal state
smb347-charger: Convert to regmap API
smb347-charger: Move IRQ enabling to the end of probe
smb347-charger: Rename few functions to match better what they are doing
smb347-charger: Convert to use module_i2c_driver()
smb347_charger: Cleanup power supply registration code in probe
ab8500: Clean up probe routines
ab8500_fg: Harden platform data check
ab8500_btemp: Harden platform data check
ab8500_charger: Harden platform data check
MAINTAINERS: Fix 'F' entry for the power supply class
max17042_battery: Handle irq request failure case
...
|
|
Pull two small kvm fixes from Avi Kivity:
"A build fix for non-kvm archs and a transparent hugepage refcount
bugfix on hosts with 4M pages."
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Export asm-generic/kvm_para.h
KVM: MMU: fix huge page adapted on non-PAE host
|
|
Pull final round of SCSI updates from James Bottomley:
"This is primarily another round of driver updates (bnx2fc, qla2xxx,
qla4xxx) including the target mode driver for qla2xxx. We've also got
a couple of regression fixes (async scanning, broken this merge window
and a fix to a long standing break in the scsi_wait_scan module)."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (45 commits)
[SCSI] fix scsi_wait_scan
[SCSI] fix async probe regression
[SCSI] be2iscsi: fix dma free size mismatch regression
[SCSI] qla4xxx: Update driver version to 5.02.00-k17
[SCSI] qla4xxx: Capture minidump for ISP82XX on firmware failure
[SCSI] qla4xxx: Add change_queue_depth API support
[SCSI] qla4xxx: Fix clear ddb mbx command failure issue.
[SCSI] qla4xxx: Fix kernel panic during discovery logout.
[SCSI] qla4xxx: Correct early completion of pending mbox.
[SCSI] fcoe, bnx2fc, libfcoe: SW FCoE and bnx2fc use FCoE Syfs
[SCSI] libfcoe: Add fcoe_sysfs
[SCSI] bnx2fc: Allocate fcoe_ctlr with bnx2fc_interface, not as a member
[SCSI] fcoe: Allocate fcoe_ctlr with fcoe_interface, not as a member
[SCSI] Fix dm-multipath starvation when scsi host is busy
[SCSI] ufs: fix potential NULL pointer dereferencing error in ufshcd_prove.
[SCSI] qla2xxx: don't free pool that wasn't allocated
[SCSI] mptfusion: unlock on error in mpt_config()
[SCSI] tcm_qla2xxx: Add >= 24xx series fabric module for target-core
[SCSI] qla2xxx: Add LLD target-mode infrastructure for >= 24xx series
[SCSI] Revert "qla2xxx: During loopdown perform Diagnostic loopback."
...
|
|
Use the same mechanism as the block devices are using, but move the
helper functions from fs/direct-io.c into fs/inode.c to remove the
dependency on CONFIG_BLOCK.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Fred Isaman <iisaman@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull networking changes from David S. Miller:
1) Fix IPSEC header length calculation for transport mode in ESP. The
issue is whether to do the calculation before or after alignment.
Fix from Benjamin Poirier.
2) Fix regression in IPV6 IPSEC fragment length calculations, from Gao
Feng. This is another transport vs tunnel mode issue.
3) Handle AF_UNSPEC connect()s properly in L2TP to avoid OOPSes. Fix
from James Chapman.
4) Fix USB ASIX driver's reception of full sized VLAN packets, from
Eric Dumazet.
5) Allow drop monitor (and, more generically, all generic netlink
protocols) to be automatically loaded as a module. From Neil
Horman.
Fix up trivial conflict in Documentation/feature-removal-schedule.txt
due to new entries added next to each other at the end. As usual.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
net/smsc911x: Repair broken failure paths
virtio-net: remove useless disable on freeze
netdevice: Update netif_dbg for CONFIG_DYNAMIC_DEBUG
drop_monitor: Add module alias to enable automatic module loading
genetlink: Build a generic netlink family module alias
net: add MODULE_ALIAS_NET_PF_PROTO_NAME
r6040: Do a Proper deinit at errorpath and also when driver unloads (calling r6040_remove_one)
r6040: disable pci device if the subsequent calls (after pci_enable_device) fails
skb: avoid unnecessary reallocations in __skb_cow
net: sh_eth: fix the rxdesc pointer when rx descriptor empty happens
asix: allow full size 8021Q frames to be received
rds_rdma: don't assume infiniband device is PCI
l2tp: fix oops in L2TP IP sockets for connect() AF_UNSPEC case
mac80211: fix ADDBA declined after suspend with wowlan
wlcore: fix undefined symbols when CONFIG_PM is not defined
mac80211: fix flag check for QoS NOACK frames
ath9k_hw: apply internal regulator settings on AR933x
ath9k_hw: update AR933x initvals to fix issues with high power devices
ath9k: fix a use-after-free-bug when ath_tx_setup_buffer() fails
ath9k: stop rx dma before stopping tx
...
|
|
Make netif_dbg use dynamic debugging whenever
CONFIG_DYNAMIC_DEBUG is enabled.
commit b558c96ffa53
("dynamic_debug: make dynamic-debug supersede DEBUG ccflag")
missed updating the netif_dbg variant.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull ceph updates from Sage Weil:
"There are some updates and cleanups to the CRUSH placement code, a bug
fix with incremental maps, several cleanups and fixes from Josh Durgin
in the RBD block device code, a series of cleanups and bug fixes from
Alex Elder in the messenger code, and some miscellaneous bounds
checking and gfp cleanups/fixes."
Fix up trivial conflicts in net/ceph/{messenger.c,osdmap.c} due to the
networking people preferring "unsigned int" over just "unsigned".
* git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (45 commits)
libceph: fix pg_temp updates
libceph: avoid unregistering osd request when not registered
ceph: add auth buf in prepare_write_connect()
ceph: rename prepare_connect_authorizer()
ceph: return pointer from prepare_connect_authorizer()
ceph: use info returned by get_authorizer
ceph: have get_authorizer methods return pointers
ceph: ensure auth ops are defined before use
ceph: messenger: reduce args to create_authorizer
ceph: define ceph_auth_handshake type
ceph: messenger: check return from get_authorizer
ceph: messenger: rework prepare_connect_authorizer()
ceph: messenger: check prepare_write_connect() result
ceph: don't set WRITE_PENDING too early
ceph: drop msgr argument from prepare_write_connect()
ceph: messenger: send banner in process_connect()
ceph: messenger: reset connection kvec caller
libceph: don't reset kvec in prepare_write_banner()
ceph: ignore preferred_osd field
ceph: fully initialize new layout
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
Pull i2c updates from Jean Delvare.
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c: Split I2C_M_NOSTART support out of I2C_FUNC_PROTOCOL_MANGLING
i2c-dev: Add support for I2C_M_RECV_LEN
|
|
Pull second set of watchdog updates from Wim Van Sebroeck:
"This changeset contains following changes:
* Add support for multiple watchdog devices. We use dynamically
allocated device id's for this.
* Add locking into the generic watchdog infrastructure.
* Add support for dynamically allocated watchdog_device structs so
that we can deal with devices that get unbound.
* convert following drivers to the generic watchdog framework:
sch5627, sch5636 and sp805_wdt.
* Add DA9052/53 PMIC watchdog support
* Fix printk format warnings for iTCO_wdt.c"
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: iTCO_wdt.c: fix printk format warnings
watchdog: sp805_wdt: Add clk_{un}prepare support
watchdog: sp805_wdt: convert to watchdog core
hwmon/sch56xx: Depend on watchdog for watchdog core functions
watchdog: sch56xx-common: set correct bits in register()
Watchdog: DA9052/53 PMIC watchdog support
watchdog: sch56xx-common: Add proper ref-counting of watchdog data
watchdog: sch56xx: Remove unnecessary checks for register changes
watchdog: sch56xx: Use watchdog core
watchdog: Add support for dynamically allocated watchdog_device structs
watchdog: Add Locking support
watchdog: watchdog_dev: Rewrite wrapper code
watchdog: use dev_ functions
watchdog: create all the proper device files
watchdog: Add a flag to indicate the watchdog doesn't reboot things
watchdog: Add multiple device support
watchdog: watchdog_core.h: make functions extern
watchdog: correct the name of the watchdog_core inlude file
watchdog: Add watchdog_active() routine
watchdog: watchdog_dev: include private header to pickup global symbol prototypes
|
|
Pull block driver updates from Jens Axboe:
"Here are the driver related changes for 3.5. It contains:
- The floppy changes from Jiri. Jiri is now also marked as the
maintainer of floppy.c, I shall be publically branding his forehead
with red hot iron at the next opportune moment.
- A batch of drbd updates and fixes from the linbit crew, as well as
fixes from others.
- Two small fixes for xen-blkfront courtesy of Jan."
* 'for-3.5/drivers' of git://git.kernel.dk/linux-block: (70 commits)
floppy: take over maintainership
floppy: remove floppy-specific O_EXCL handling
floppy: convert to delayed work and single-thread wq
xen-blkfront: module exit handling adjustments
xen-blkfront: properly name all devices
drbd: grammar fix in log message
drbd: check MODULE for THIS_MODULE
drbd: Restore the request restart logic
drbd: introduce a bio_set to allocate housekeeping bios from
drbd: remove unused define
drbd: bm_page_async_io: properly initialize page->private
drbd: use the newly introduced page pool for bitmap IO
drbd: add page pool to be used for meta data IO
drbd: allow bitmap to change during writeout from resync_finished
drbd: fix race between drbdadm invalidate/verify and finishing resync
drbd: fix resend/resubmit of frozen IO
drbd: Ensure that data_size is not 0 before using data_size-1 as index
drbd: Delay/reject other state changes while establishing a connection
drbd: move put_ldev from __req_mod() to the endio callback
drbd: fix WRITE_ACKED_BY_PEER_AND_SIS to not set RQ_NET_DONE
...
|
|
Merge block/IO core bits from Jens Axboe:
"This is a bit bigger on the core side than usual, but that is purely
because we decided to hold off on parts of Tejun's submission on 3.4
to give it a bit more time to simmer. As a consequence, it's seen a
long cycle in for-next.
It contains:
- Bug fix from Dan, wrong locking type.
- Relax splice gifting restriction from Eric.
- A ton of updates from Tejun, primarily for blkcg. This improves
the code a lot, making the API nicer and cleaner, and also includes
fixes for how we handle and tie policies and re-activate on
switches. The changes also include generic bug fixes.
- A simple fix from Vivek, along with a fix for doing proper delayed
allocation of the blkcg stats."
Fix up annoying conflict just due to different merge resolution in
Documentation/feature-removal-schedule.txt
* 'for-3.5/core' of git://git.kernel.dk/linux-block: (92 commits)
blkcg: tg_stats_alloc_lock is an irq lock
vmsplice: relax alignement requirements for SPLICE_F_GIFT
blkcg: use radix tree to index blkgs from blkcg
blkcg: fix blkcg->css ref leak in __blkg_lookup_create()
block: fix elvpriv allocation failure handling
block: collapse blk_alloc_request() into get_request()
blkcg: collapse blkcg_policy_ops into blkcg_policy
blkcg: embed struct blkg_policy_data in policy specific data
blkcg: mass rename of blkcg API
blkcg: style cleanups for blk-cgroup.h
blkcg: remove blkio_group->path[]
blkcg: blkg_rwstat_read() was missing inline
blkcg: shoot down blkgs if all policies are deactivated
blkcg: drop stuff unused after per-queue policy activation update
blkcg: implement per-queue policy activation
blkcg: add request_queue->root_blkg
blkcg: make request_queue bypassing on allocation
blkcg: make sure blkg_lookup() returns %NULL if @q is bypassing
blkcg: make blkg_conf_prep() take @pol and return with queue lock held
blkcg: remove static policy ID enums
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"Not much stuff this time. The only change to the IOMMU core code is
the addition of a handle to the fault handling code. A few updates to
the AMD IOMMU driver to work around new errata. The other patches are
mostly fixes and enhancements to the existing ARM IOMMU drivers and
documentation updates.
A new IOMMU driver for the Exynos platform was also underway but got
merged via the Samsung tree and is not part of this tree."
* tag 'iommu-updates-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
Documentation: kernel-parameters.txt Add amd_iommu_dump
iommu/core: pass a user-provided token to fault handlers
iommu/tegra: gart: Fix register offset correctly
iommu: OMAP: device detach on domain destroy
iommu: tegra/gart: Add device tree support
iommu: tegra/gart: use correct gart_device
iommu/tegra: smmu: Print device name correctly
iommu/amd: Add workaround for event log erratum
iommu/amd: Check for the right TLP prefix bit
dma-debug: release free_entries_lock before saving stack trace
|
|
Since there are uses for I2C_M_NOSTART which are much more sensible and
standard than most of the protocol mangling functionality (the main one
being gather writes to devices where something like a register address
needs to be inserted before a block of data) create a new I2C_FUNC_NOSTART
for this feature and update all the users to use it.
Also strengthen the disrecommendation of the protocol mangling while we're
at it.
In the case of regmap-i2c we remove the requirement for mangling as
I2C_M_NOSTART is the only mangling feature which is being used.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
If a driver's watchdog_device struct is part of a dynamically allocated
struct (which it often will be), merely locking the module is not enough,
even with a drivers module locked, the driver can be unbound from the device,
examples:
1) The root user can unbind it through sysfd
2) The i2c bus master driver being unloaded for an i2c watchdog
I will gladly admit that these are corner cases, but we still need to handle
them correctly.
The fix for this consists of 2 parts:
1) Add ref / unref operations, so that the driver can refcount the struct
holding the watchdog_device struct and delay freeing it until any
open filehandles referring to it are closed
2) Most driver operations will do IO on the device and the driver should not
do any IO on the device after it has been unbound. Rather then letting each
driver deal with this internally, it is better to ensure at the watchdog
core level that no operations (other then unref) will get called after
the driver has called watchdog_unregister_device(). This actually is the
bulk of this patch.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
This patch fixes some potential multithreading issues, despite only
allowing one process to open the /dev/watchdog device, we can still get
called multiple times at the same time, since a program could be using thread,
or could share the fd after a fork.
This causes 2 potential problems:
1) watchdog_start / open do an unlocked test_n_set / test_n_clear,
if these 2 race, the watchdog could be stopped while the active
bit indicates it is running or visa versa.
2) Most watchdog_dev drivers probably assume that only one
watchdog-op will get called at a time, this is not necessary
true atm.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Create the watchdog class and it's associated devices.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Some watchdogs merely trigger external alarms and controls. In a managed
environment this is very useful but we want drivers to be able to figure
out which is which now multiple dogs can be loaded. Thus add an ALARMONLY
feature flag.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
We keep the old /dev/watchdog interface file for the first watchdog via
miscdev. This is basically a cut and paste of the relevant interface code
from the rtc driver layer tweaked for watchdog.
Revised to fix problems noted by Hans de Goede
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Some watchdog may need to check if watchdog is ACTIVE or not, for example in
their suspend/resume hooks.
This patch adds this routine and changes the core drivers to use it.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Generic netlink searches for -type- formatted aliases when requesting a module to
fulfill a protocol request (i.e. net-pf-16-proto-16-type-<x>, where x is a type
value). However generic netlink protocols have no well defined type numbers,
they have string names. Modify genl_ctrl_getfamily to request an alias in the
format net-pf-16-proto-16-family-<x> instead, where x is a generic string, and
add a macro that builds on the previously added MODULE_ALIAS_NET_PF_PROTO_NAME
macro to allow modules to specifify those generic strings.
Note, l2tp previously hacked together an net-pf-16-proto-16-type-l2tp alias
using the MODULE_ALIAS macro, with these updates we can convert that to use the
PROTO_NAME macro.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: James Chapman <jchapman@katalix.com>
CC: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MODULE_ALAIS_NET_PF macro set is missing a variant that allows for the
appending of an arbitrary string to the net-pf-<x>-proto-<y> base. while
MODULE_ALIAS_NET_PF_PROTO_NAME_TYPE allows an appending of a numerical type, we
need to be able to append a generic string to support generic netlink families
that have neither a fix numberical protocol nor type number
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull EDAC internal API changes from Mauro Carvalho Chehab:
"This changeset is the first part of a series of patches that fixes the
EDAC sybsystem. On this set, it changes the Kernel EDAC API in order
to properly represent the Intel i3/i5/i7, Xeon 3xxx/5xxx/7xxx, and
Intel E5-xxxx memory controllers.
The EDAC core used to assume that:
- the DRAM chip select pin is directly accessed by the memory
controller
- when multiple channels are used, they're all filled with the
same type of memory.
None of the above premises is true on Intel memory controllers since
2002, when RAMBUS and FB-DIMMs were introduced, and Advanced Memory
Buffer or by some similar technologies hides the direct access to the
DRAM pins.
So, the existing drivers for those chipsets had to lie to the EDAC
core, in general telling that just one channel is filled. That
produces some hard to understand error messages like:
EDAC MC0: CE row 3, channel 0, label "DIMM1": 1 Unknown error(s): memory read error on FATAL area : cpu=0 Err=0008:00c2 (ch=2), addr = 0xad1f73480 => socket=0, Channel=0(mask=2), rank=1
The location information there (row3 channel 0) is completely bogus:
it has no physical meaning, and are just some random values that the
driver uses to talk with the EDAC core. The error actually happened
at CPU socket 0, channel 0, slot 1, but this is not reported anywhere,
as the EDAC core doesn't know anything about the memory layout. So,
only advanced users that know how the EDAC driver works and that tests
their systems to see how DIMMs are mapped can actually benefit for
such error logs.
This patch series fixes the error report logic, in order to allow the
EDAC to expose the memory architecture used by them to the EDAC core.
So, as the EDAC core now understands how the memory is organized, it
can provide an useful report:
EDAC MC0: CE memory read error on DIMM1 (channel:0 slot:1 page:0x364b1b offset:0x600 grain:32 syndrome:0x0 - count:1 area:DRAM err_code:0001:0090 socket:0 channel_mask:1 rank:4)
The location of the DIMM where the error happened is reported by "MC0"
(cpu socket #0), at "channel:0 slot:1" location, and matches the
physical location of the DIMM.
There are two remaining issues not covered by this patch series:
- The EDAC sysfs API will still report bogus values. So,
userspace tools like edac-utils will still use the bogus data;
- Add a new tracepoint-based way to get the binary information
about the errors.
Those are on a second series of patches (also at -next), but will
probably miss the train for 3.5, due to the slow review process."
Fix up trivial conflict (due to spelling correction of removed code) in
drivers/edac/edac_device.c
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac: (42 commits)
i7core: fix ranks information at the per-channel struct
i5000: Fix the fatal error handling
i5100_edac: Fix a warning when compiled with 32 bits
i82975x_edac: Test nr_pages earlier to save a few CPU cycles
e752x_edac: provide more info about how DIMMS/ranks are mapped
i5000_edac: Fix the logic that retrieves memory information
i5400_edac: improve debug messages to better represent the filled memory
edac: Cleanup the logs for i7core and sb edac drivers
edac: Initialize the dimm label with the known information
edac: Remove the legacy EDAC ABI
x38_edac: convert driver to use the new edac ABI
tile_edac: convert driver to use the new edac ABI
sb_edac: convert driver to use the new edac ABI
r82600_edac: convert driver to use the new edac ABI
ppc4xx_edac: convert driver to use the new edac ABI
pasemi_edac: convert driver to use the new edac ABI
mv64x60_edac: convert driver to use the new edac ABI
mpc85xx_edac: convert driver to use the new edac ABI
i82975x_edac: convert driver to use the new edac ABI
i82875p_edac: convert driver to use the new edac ABI
...
|
|
Pull MIPS updates from Ralf Baechle:
"The whole series has been sitting in -next for quite a while with no
complaints. The last change to the series was before the weekend the
removal of an SPI patch which Grant - even though previously acked by
himself - appeared to raise objections. So I removed it until the
situation is clarified. Other than that all the patches have the acks
from their respective maintainers, all MIPS and x86 defconfigs are
building fine and I'm not aware of any problems introduced by this
series.
Among the key features for this patch series is a sizable patchset for
Lantiq which among other things introduces support for Lantiq's
flagship product, the FALCON SOC. It also means that the opensource
developers behind this patchset have overtaken Lantiq's competing
inhouse development team that was working behind closed doors.
Less noteworthy the ath79 patchset which adds support for a few more
chip variants, cleanups and fixes. Finally the usual dose of tweaking
of generic code."
Fix up trivial conflicts in arch/mips/lantiq/xway/gpio_{ebu,stp}.c where
printk spelling fixes clashed with file move and eventual removal of the
printk.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (81 commits)
MIPS: lantiq: remove orphaned code
MIPS: Remove all -Wall and almost all -Werror usage from arch/mips.
MIPS: lantiq: implement support for FALCON soc
MTD: MIPS: lantiq: verify that the NOR interface is available on falcon soc
MTD: MIPS: lantiq: implement OF support
watchdog: MIPS: lantiq: implement OF support and minor fixes
SERIAL: MIPS: lantiq: implement OF support
GPIO: MIPS: lantiq: convert gpio-stp-xway to OF
GPIO: MIPS: lantiq: convert gpio-mm-lantiq to OF and of_mm_gpio
GPIO: MIPS: lantiq: move gpio-stp and gpio-ebu to the subsystem folder
MIPS: pci: convert lantiq driver to OF
MIPS: lantiq: convert dma to platform driver
MIPS: lantiq: implement support for clkdev api
MIPS: lantiq: drop ltq_gpio_request() and gpio_to_irq()
OF: MIPS: lantiq: implement irq_domain support
OF: MIPS: lantiq: implement OF support
MIPS: lantiq: drop mips_machine support
OF: PCI: const usage needed by MIPS
MIPS: Cavium: Remove smp_reserve_lock.
MIPS: Move cache setup to setup_arch().
...
|
|
Some DS13XX devices have "trickle chargers". Its configuration register
is at different locations, the setup is the same, though. Since the
configuration is board specific, introduce a platform_data to this driver.
Tested with a DS1339 on a custom board.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently there is no generic way to get the RTC battery status within an
application. So add an ioctl to read the status bit. The idea is that
the bit is set once a low voltage is detected. It stays there until it is
reset using the RTC_VL_CLR ioctl.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Using %ps in a printk format will sometimes fail silently and print the
empty string if the address passed in does not match a symbol that
kallsyms knows about. But using %pS will fall back to printing the full
address if kallsyms can't find the symbol. Make %ps act the same as %pS
by falling back to printing the address.
While we're here also make %ps print the module that a symbol comes from
so that it matches what %pS already does. Take this simple function for
example (in a module):
static void test_printk(void)
{
int test;
pr_info("with pS: %pS\n", &test);
pr_info("with ps: %ps\n", &test);
}
Before this patch:
with pS: 0xdff7df44
with ps:
After this patch:
with pS: 0xdff7df44
with ps: 0xdff7df44
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
max brightness is 127, so the range of brt_val should be from 0 to 127
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Shreshtha Kumar SAHU <shreshthakumar.sahu@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a new field to led_classdev to save activattion state after activate
routine is successful. This saved state is used in deactivate routine to
do cleanup such as removing device files, and free memory allocated during
activation. Currently trigger_data not being null is used for this
purpose.
Existing triggers will need changes to use this new field.
Signed-off-by: Shuah Khan <shuahkhan@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
prototypes
Include the header to pickup the exported symbol prototype.
Quiets the sparse warning:
warning: symbol 'apple_bl_register' was not declared. Should it be static?
warning: symbol 'apple_bl_unregister' was not declared. Should it be static?
[akpm@linux-foundation.org: fix resulting build error]
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patchset adds early fb blank feature that a callback of lcd panel
driver is called prior to specific fb driver's one. In the case of
MIPI-DSI based video mode LCD Panel, for lcd power off, the power off
commands should be transferred to lcd panel with display and mipi-dsi
controller enabled because the commands is set to lcd panel at vsync porch
period. and in opposite case, the callback of fb driver should be called
prior to lcd panel driver's one because of same issue. Also if fb_blank
mode is changed to FB_BLANK_POWERDOWN then display controller would be
off(clock disable) but lcd panel would be still on. at this time, you
could see some issue like sparkling on lcd panel because video clock to be
delivered to ldi module of lcd panel was disabled. this issue could
occurs for all lcd panels.
The callback order is as the following:
at fb_blank function of fbmem.c
-> fb_notifier_call_chain(FB_EARLY_EVENT_BLANK)
-> lcd panel driver's early_set_power()
-> info->fbops->fb_blank()
-> spcefic fb driver's fb_blank()
-> fb_notifier_call_chain(FB_EVENT_BLANK)
-> lcd panel driver's set_power()
-> fb_notifier_call_chain(FB_R_EARLY_EVENT_BLANK) if
info->fops->fb_blank() was failed.
fb_notifier_call_chain(FB_R_EARLY_EVENT_BLANK) would be called to revert
the effects of previous FB_EARLY_EVENT_BLANK call. and note that if
early_set_power() of lcd_ops is NULL then early fb blank callback would be
ignored.
This patch:
Add early_set_power and r_early_set_power callbacks. early_set_power
callback is called prior to fb_blank() of fbmem.c and r_early_set_power
callback is called if fb_blank() was failed to revert the effects of the
early_set_power call of lcd panel driver.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
