| Age | Commit message (Collapse) | Author |
|---|
|
CONFIG_HOTPLUG is going away as an option so __devinitconst is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds support for the ADIS16375, ADIS16480, ADIS16485, ADIS16488 6
degree to 10 degree of freedom IMUs.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Factor out the code for parsing fixed point numbers into its own function and
make this function globally available. This allows us to reuse the code to parse
fixed point numbers in individual IIO drivers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patch adds support for a new IIO channel type for pressure measurements.
This can for example be used for barometric pressure sensors.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Some of the newer generation devices from the ADIS16XXX series have more
registers than what can be supported with the current register addressing
scheme. These devices implement register paging to support a larger register
range. Each page is 128 registers large and the currently active page can be
selected via register 0x00 in each page. This patch implements transparent
paging inside the common adis library. The register read/write interface stays
the same and when a register is accessed the library automatically switches to
the correct page if it is not already selected. The page number is encoded in
the upper bits of the register number, e.g. register 0x5 of page 1 is 0x85.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Some of the newer generation devices from the ADIS16XXX family have 32bit wide
register which spans two 16bit wide registers. This patch adds support for
reading and writing a 32bit wide register.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Provide a IIO debugfs register access function for the ADIS library. This
function can be used by individual drivers to allow raw register access via
debugfs.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The driver does not expose any custom API to userspace and none of the standard
static code checker tools report any issues, so move it out of staging.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Now that the adis library no longer depends on the sw_ring buffer implementation
we can move it out of staging.
While we are at it also sort the entries in the iio Kconfig and Makefile to be
in alphabetical order.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Match the iio_buffer_register stub signature up to the real function and make
the second parameter const. This fixes a the following warnings if
CONFIG_IIO_BUFFER is disabled:
drivers/staging/iio/accel/adis16201_core.c: In function ‘adis16201_probe’:
drivers/staging/iio/accel/adis16201_core.c:536: warning: passing argument 2 of ‘iio_buffer_register’ discards qualifiers from pointer target type
drivers/staging/iio/accel/adis16203_core.c: In function ‘adis16203_probe’:
drivers/staging/iio/accel/adis16203_core.c:468: warning: passing argument 2 of ‘iio_buffer_register’ discards qualifiers from pointer target type
drivers/staging/iio/accel/adis16204_core.c: In function ‘adis16204_probe’:
drivers/staging/iio/accel/adis16204_core.c:527: warning: passing argument 2 of ‘iio_buffer_register’ discards qualifiers from pointer target type
drivers/staging/iio/accel/adis16209_core.c: In function ‘adis16209_probe’:
drivers/staging/iio/accel/adis16209_core.c:542: warning: passing argument 2 of ‘iio_buffer_register’ discards qualifiers from pointer target type
drivers/staging/iio/accel/adis16240_core.c: In function ‘adis16240_probe’:
drivers/staging/iio/accel/adis16240_core.c:588: warning: passing argument 2 of ‘iio_buffer_register’ discards qualifiers from pointer target type
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
|
|
Merge misc fixes from Andrew Morton.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (12 patches)
revert "mm: fix-up zone present pages"
tmpfs: change final i_blocks BUG to WARNING
tmpfs: fix shmem_getpage_gfp() VM_BUG_ON
mm: highmem: don't treat PKMAP_ADDR(LAST_PKMAP) as a highmem address
mm: revert "mm: vmscan: scale number of pages reclaimed by reclaim/compaction based on failures"
rapidio: fix kernel-doc warnings
swapfile: fix name leak in swapoff
memcg: fix hotplugged memory zone oops
mips, arc: fix build failure
memcg: oom: fix totalpages calculation for memory.swappiness==0
mm: fix build warning for uninitialized value
mm: add anon_vma_lock to validate_mm()
|
|
Revert commit 7f1290f2f2a4 ("mm: fix-up zone present pages")
That patch tried to fix a issue when calculating zone->present_pages,
but it caused a regression on 32bit systems with HIGHMEM. With that
change, reset_zone_present_pages() resets all zone->present_pages to
zero, and fixup_zone_present_pages() is called to recalculate
zone->present_pages when the boot allocator frees core memory pages into
buddy allocator. Because highmem pages are not freed by bootmem
allocator, all highmem zones' present_pages becomes zero.
Various options for improving the situation are being discussed but for
now, let's return to the 3.6 code.
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Petr Tesarik <ptesarik@suse.cz>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: David Rientjes <rientjes@google.com>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix rapidio kernel-doc warnings:
Warning(drivers/rapidio/rio.c:415): No description found for parameter 'local'
Warning(drivers/rapidio/rio.c:415): Excess function parameter 'lstart' description in 'rio_map_inb_region'
Warning(include/linux/rio.h:290): No description found for parameter 'switches'
Warning(include/linux/rio.h:290): No description found for parameter 'destid_table'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Acked-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When MEMCG is configured on (even when it's disabled by boot option),
when adding or removing a page to/from its lru list, the zone pointer
used for stats updates is nowadays taken from the struct lruvec. (On
many configurations, calculating zone from page is slower.)
But we have no code to update all the lruvecs (per zone, per memcg) when
a memory node is hotadded. Here's an extract from the oops which
results when running numactl to bind a program to a newly onlined node:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000f60
IP: __mod_zone_page_state+0x9/0x60
Pid: 1219, comm: numactl Not tainted 3.6.0-rc5+ #180 Bochs Bochs
Process numactl (pid: 1219, threadinfo ffff880039abc000, task ffff8800383c4ce0)
Call Trace:
__pagevec_lru_add_fn+0xdf/0x140
pagevec_lru_move_fn+0xb1/0x100
__pagevec_lru_add+0x1c/0x30
lru_add_drain_cpu+0xa3/0x130
lru_add_drain+0x2f/0x40
...
The natural solution might be to use a memcg callback whenever memory is
hotadded; but that solution has not been scoped out, and it happens that
we do have an easy location at which to update lruvec->zone. The lruvec
pointer is discovered either by mem_cgroup_zone_lruvec() or by
mem_cgroup_page_lruvec(), and both of those do know the right zone.
So check and set lruvec->zone in those; and remove the inadequate
attempt to set lruvec->zone from lruvec_init(), which is called before
NODE_DATA(node) has been allocated in such cases.
Ah, there was one exceptionr. For no particularly good reason,
mem_cgroup_force_empty_list() has its own code for deciding lruvec.
Change it to use the standard mem_cgroup_zone_lruvec() and
mem_cgroup_get_lru_size() too. In fact it was already safe against such
an oops (the lru lists in danger could only be empty), but we're better
proofed against future changes this way.
I've marked this for stable (3.6) since we introduced the problem in 3.5
(now closed to stable); but I have no idea if this is the only fix
needed to get memory hotadd working with memcg in 3.6, and received no
answer when I enquired twice before.
Reported-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Its contents are merged into ipack.h. So this file is not needed.
Doing that, it simplifies the ipack-related driver development.
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move ipack header files to include/linux/ directory where they belong.
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is mostly a revert of 01dc52ebdf47 ("oom: remove deprecated oom_adj")
from Davidlohr Bueso.
It reintroduces /proc/pid/oom_adj for backwards compatibility with earlier
kernels. It simply scales the value linearly when /proc/pid/oom_score_adj
is written.
The major difference is that its scheduled removal is no longer included
in Documentation/feature-removal-schedule.txt. We do warn users with a
single printk, though, to suggest the more powerful and supported
/proc/pid/oom_score_adj interface.
Reported-by: Artem S. Tashkinov <t.artem@lycos.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We've been sitting on this longer than we meant to due to travel and
other activities, but the number of patches is luckily not that high.
Biggest changes are from a batch of OMAP bugfixes, but there are a few
for the broader set of SoCs too (bcm2835, pxa, highbank, tegra, at91
and i.MX).
The OMAP patches contain some fixes for MUSB/PHY on omap4 which ends
up being a bit on the large side but needed for legacy (non-DT)
platforms. Beyond that there are a handful of hwmod/pm changes.
So, fairly noncontroversial stuff all in all, and as usual around this
time the fixes are well targeted at specific problems."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx: ehci: fix host power mask bit
ARM i.MX: fix error-valued pointer dereference in clk_register_gate2()
ARM: at91/usbh: fix overcurrent gpio setup
ARM: at91/AT91SAM9G45: fix crypto peripherals irq issue due to sparse irq support
ARM: boot: Fix usage of kecho
ARM: OMAP: ocp2scp: create omap device for ocp2scp
ARM: OMAP4: add _dev_attr_ to ocp2scp for representing usb_phy
drivers: bus: ocp2scp: add pdata support
irqchip: irq-bcm2835: Add terminating entry for of_device_id table
ARM: highbank: retry wfi on reset request
ARM: OMAP4: PM: fix regulator name for VDD_MPU
ARM: OMAP4: hwmod data: do not enable or reset the McPDM during kernel init
ARM: OMAP2+: hwmod: add flag to prevent hwmod code from touching IP block during init
ARM: dt: tegra: fix length of pad control and mux registers
ARM: OMAP: hwmod: wait for sysreset complete after enabling hwmod
ARM: OMAP2+: clockdomain: Fix OMAP4 ISS clk domain to support only SWSUP
ARM: pxa/spitz_pm: Fix hang when resuming from STR
ARM: pxa: hx4700: Fix backlight PWM device number
ARM: OMAP2+: PM: add missing newline to VC warning message
|
|
fixes
From Sascha Hauer <s.hauer@pengutronix.de>:
ARM i.MX fixes for 3.7-rc
* tag 'imx-fixes-rc' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM: imx: ehci: fix host power mask bit
ARM i.MX: fix error-valued pointer dereference in clk_register_gate2()
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Users of GCC 4.7 have reported compiler errors due to having inline
applied to function declarations in clk-provider.h. The definitions
exist in drivers/clk/clk.c. An example error:
In file included from arch/arm/mach-omap2/clockdomain.c:25:0:
arch/arm/mach-omap2/clockdomain.c: In function ‘clkdm_clk_disable’:
include/linux/clk-provider.h:338:12: error: inlining failed in call to always_inline ‘__clk_get_enable_count’: function body not available
arch/arm/mach-omap2/clockdomain.c:1001:28: error: called from here
make[1]: *** [arch/arm/mach-omap2/clockdomain.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2
This patch removes the use of inline from include/linux/clk-provider.h
but keeps the function definitions in drivers/clk/clk.c as inlined since
they are one-liners.
Signed-off-by: Igor Mazanov <i.mazanov@gmail.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
[mturquette@linaro.org: improved subject, added changelog]
|
|
Turns out that consumer.h needs to include types.h on some platforms to
build properly (like powerpc).
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
IIO cleanups and fixes from Jonathan:
"4th set of IIO driver updates and new functionality for the 3.8 cycle.
2 drivers going through final cleanup and moving out of staging.
Addition to the core of support for multiple buffers from a single
datastream. This functionality is core in allowing multiple users
of interrupt driven data streams from the devices. First user
will shortly be an input bridge driver. This has been in review
/ revision for over a year resulting in a far cleaner result.
Much of the work had been in precursor patches. Here we just
add the buffer set tear up and down support + switch to multiple
buffer pushing in the drivers (a one line change in all users).
Thanks to those who have tested / reviewed this set."
|
|
|
|
Pull networking fixes from David Miller:
"Bug fixes galore, mostly in drivers as is often the case:
1) USB gadget and cdc_eem drivers need adjustments to their frame size
lengths in order to handle VLANs correctly. From Ian Coolidge.
2) TIPC and several network drivers erroneously call tasklet_disable
before tasklet_kill, fix from Xiaotian Feng.
3) r8169 driver needs to apply the WOL suspend quirk to more chipsets,
fix from Cyril Brulebois.
4) Fix multicast filters on RTL_GIGA_MAC_VER_35 r8169 chips, from
Nathan Walp.
5) FDB netlink dumps should use RTM_NEWNEIGH as the message type, not
zero. From John Fastabend.
6) Fix smsc95xx tx checksum offload on big-endian, from Steve
Glendinning.
7) __inet_diag_dump() needs to repsect and report the error value
returned from inet_diag_lock_handler() rather than ignore it.
Otherwise if an inet diag handler is not available for a particular
protocol, we essentially report success instead of giving an error
indication. Fix from Cyrill Gorcunov.
8) When the QFQ packet scheduler sees TSO/GSO packets it does not
handle things properly, and in fact ends up corrupting it's
datastructures as well as mis-schedule packets. Fix from Paolo
Valente.
9) Fix oopser in skb_loop_sk(), from Eric Leblond.
10) CXGB4 passes partially uninitialized datastructures in to FW
commands, fix from Vipul Pandya.
11) When we send unsolicited ipv6 neighbour advertisements, we should
send them to the link-local allnodes multicast address, as per
RFC4861. Fix from Hannes Frederic Sowa.
12) There is some kind of bug in the usbnet's kevent deferral
mechanism, but more immediately when it triggers an uncontrolled
stream of kernel messages spam the log. Rate limit the error log
message triggered when this problem occurs, as sending thousands
of error messages into the kernel log doesn't help matters at all,
and in fact makes further diagnosis more difficult.
From Steve Glendinning.
13) Fix gianfar restore from hibernation, from Wang Dongsheng.
14) The netlink message attribute sizes are wrong in the ipv6 GRE
driver, it was using the size of ipv4 addresses instead of ipv6
ones :-) Fix from Nicolas Dichtel."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
gre6: fix rtnl dump messages
gianfar: ethernet vanishes after restoring from hibernation
usbnet: ratelimit kevent may have been dropped warnings
ipv6: send unsolicited neighbour advertisements to all-nodes
net: usb: cdc_eem: Fix rx skb allocation for 802.1Q VLANs
usb: gadget: g_ether: fix frame size check for 802.1Q
cxgb4: Fix initialization of SGE_CONTROL register
isdn: Make CONFIG_ISDN depend on CONFIG_NETDEVICES
cxgb4: Initialize data structures before using.
af-packet: fix oops when socket is not present
pkt_sched: enable QFQ to support TSO/GSO
net: inet_diag -- Return error code if protocol handler is missed
net: bnx2x: Fix typo in bnx2x driver
smsc95xx: fix tx checksum offload for big endian
rtnetlink: Use nlmsg type RTM_NEWNEIGH from dflt fdb dump
ptp: update adjfreq callback description
r8169: allow multicast packets on sub-8168f chipset.
r8169: Fix WoL on RTL8168d/8111d.
drivers/net: use tasklet_kill in device remove/close process
tipc: do not use tasklet_disable before tasklet_kill
|
|
Pull sparc fixes from David Miller:
"Several build/bug fixes for sparc, including:
1) Configuring a mix of static vs. modular sparc64 crypto modules
didn't work, remove an ill-conceived attempt to only have to build
the device match table for these drivers once to fix the problem.
Reported by Meelis Roos.
2) Make the montgomery multiple/square and mpmul instructions actually
usable in 32-bit tasks. Essentially this involves providing 32-bit
userspace with a way to use a 64-bit stack when it needs to.
3) Our sparc64 atomic backoffs don't yield cpu strands properly on
Niagara chips. Use pause instruction when available to achieve
this, otherwise use a benign instruction we know blocks the strand
for some time.
4) Wire up kcmp
5) Fix the build of various drivers by removing the unnecessary
blocking of OF_GPIO when SPARC.
6) Fix unintended regression wherein of_address_to_resource stopped
being provided. Fix from Andreas Larsson.
7) Fix NULL dereference in leon_handle_ext_irq(), also from Andreas
Larsson."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix build with mix of modular vs. non-modular crypto drivers.
sparc: Support atomic64_dec_if_positive properly.
of/address: sparc: Declare of_address_to_resource() as an extern function for sparc again
sparc32, leon: Check for existent irq_map entry in leon_handle_ext_irq
sparc: Add sparc support for platform_get_irq()
sparc: Allow OF_GPIO on sparc.
qlogicpti: Fix build warning.
sparc: Wire up sys_kcmp.
sparc64: Improvde documentation and readability of atomic backoff code.
sparc64: Use pause instruction when available.
sparc64: Fix cpu strand yielding.
sparc64: Make montmul/montsqr/mpmul usable in 32-bit threads.
|
|
This callback buffer is meant to be opaque to users, but basically
adds a very simple pass through buffer to which data may be
pushed when it is inserted into the buffer list.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Used to allow information about a given channel mapping to be passed
through from board files to the consumer drivers.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Route all buffer writes through the demux.
Addition or removal of a buffer results in tear down and
setup of all the buffers for a given device.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Tested-by: srinivas pandruvada <srinivas.pandruvada@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen fixes from Konrad Rzeszutek Wilk:
"There are three ARM compile fixes (we forgot to export certain
functions and if the drivers are built as an module - we go belly-up).
There is also an mismatch of irq_enter() / exit_idle() calls sequence
which were fixed some time ago in other piece of codes, but failed to
appear in the Xen code.
Lastly a fix for to help in the field with troubleshooting in case we
cannot get the appropriate parameter and also fallback code when
working with very old hypervisors."
Bug-fixes:
- Fix compile issues on ARM.
- Fix hypercall fallback code for old hypervisors.
- Print out which HVM parameter failed if it fails.
- Fix idle notifier call after irq_enter.
* tag 'stable/for-linus-3.7-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/arm: Fix compile errors when drivers are compiled as modules (export more).
xen/arm: Fix compile errors when drivers are compiled as modules.
xen/generic: Disable fallback build on ARM.
xen/events: fix RCU warning, or Call idle notifier after irq_enter()
xen/hvm: If we fail to fetch an HVM parameter print out which flag it is.
xen/hypercall: fix hypercall fallback code for very old hypervisors
|
|
for sparc again
This bug-fix makes sure that of_address_to_resource is defined extern for sparc
so that the sparc-specific implementation of of_address_to_resource() is once
again used when including include/linux/of_address.h in a sparc context. A
number of drivers in mainline relies on this function working for sparc.
The bug was introduced in a850a7554442f08d3e910c6eeb4ee216868dda1e, "of/address:
add empty static inlines for !CONFIG_OF". Contrary to that commit title, the
static inlines are added for !CONFIG_OF_ADDRESS, and CONFIG_OF_ADDRESS is never
defined for sparc. This is good behavior for the other functions in
include/linux/of_address.h, as the extern functions defined in
drivers/of/address.c only gets linked when OF_ADDRESS is configured. However,
for of_address_to_resource there exists a sparc-specific implementation in
arch/sparc/arch/sparc/kernel/of_device_common.c
Solution suggested by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC fixes from Chris Ball:
- sdhci: fix a NULL dereference at resume-time, seen on OLPC XO-4
- sdhci: fix against 3.7-rc1 for UHS modes without a vqmmc regulator
- sdhci-of-esdhc: disable CMD23 on boards where it's broken
- sdhci-s3c: fix against 3.7-rc1 for card detection with runtime PM
- dw_mmc, omap_hsmmc: fix potential NULL derefs, compiler warnings
* tag 'mmc-fixes-for-3.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: sdhci-s3c: fix the card detection in runtime-pm
mmc: sdhci-s3c: use clk_prepare_enable and clk_disable_unprepare
mmc: dw_mmc: constify dw_mci_idmac_ops in exynos back-end
mmc: dw_mmc: fix modular build for exynos back-end
mmc: sdhci: fix NULL dereference in sdhci_request() tuning
mmc: sdhci: fix IS_ERR() checking of regulator_get()
mmc: fix sdhci-dove probe/removal
mmc: sh_mmcif: fix use after free
mmc: sdhci-pci: fix 'Invalid iomem size' error message condition
mmc: mxcmmc: Fix MODULE_ALIAS
mmc: omap_hsmmc: fix NULL pointer dereference for dt boot
mmc: omap_hsmmc: fix host reference after mmc_free_host
mmc: dw_mmc: fix multiple drv_data NULL dereferences
mmc: dw_mmc: enable controller interrupt before calling mmc_start_host
mmc: sdhci-of-esdhc: disable CMD23 for some Freescale SoCs
mmc: dw_mmc: remove _dev_info compile warning
mmc: dw_mmc: convert the variable type of irq
|
|
Revert commit 03a7beb55b9f ("epoll: support for disabling items, and a
self-test app") pending resolution of the issues identified by Michael
Kerrisk, copied below.
We'll revisit this for 3.8.
: I've taken a look at this patch as it currently stands in 3.7-rc1, and
: done a bit of testing. (By the way, the test program
: tools/testing/selftests/epoll/test_epoll.c does not compile...)
:
: There are one or two places where the behavior seems a little strange,
: so I have a question or two at the end of this mail. But other than
: that, I want to check my understanding so that the interface can be
: correctly documented.
:
: Just to go though my understanding, the problem is the following
: scenario in a multithreaded application:
:
: 1. Multiple threads are performing epoll_wait() operations,
: and maintaining a user-space cache that contains information
: corresponding to each file descriptor being monitored by
: epoll_wait().
:
: 2. At some point, a thread wants to delete (EPOLL_CTL_DEL)
: a file descriptor from the epoll interest list, and
: delete the corresponding record from the user-space cache.
:
: 3. The problem with (2) is that some other thread may have
: previously done an epoll_wait() that retrieved information
: about the fd in question, and may be in the middle of using
: information in the cache that relates to that fd. Thus,
: there is a potential race.
:
: 4. The race can't solved purely in user space, because doing
: so would require applying a mutex across the epoll_wait()
: call, which would of course blow thread concurrency.
:
: Right?
:
: Your solution is the EPOLL_CTL_DISABLE operation. I want to
: confirm my understanding about how to use this flag, since
: the description that has accompanied the patches so far
: has been a bit sparse
:
: 0. In the scenario you're concerned about, deleting a file
: descriptor means (safely) doing the following:
: (a) Deleting the file descriptor from the epoll interest list
: using EPOLL_CTL_DEL
: (b) Deleting the corresponding record in the user-space cache
:
: 1. It's only meaningful to use this EPOLL_CTL_DISABLE in
: conjunction with EPOLLONESHOT.
:
: 2. Using EPOLL_CTL_DISABLE without using EPOLLONESHOT in
: conjunction is a logical error.
:
: 3. The correct way to code multithreaded applications using
: EPOLL_CTL_DISABLE and EPOLLONESHOT is as follows:
:
: a. All EPOLL_CTL_ADD and EPOLL_CTL_MOD operations should
: should EPOLLONESHOT.
:
: b. When a thread wants to delete a file descriptor, it
: should do the following:
:
: [1] Call epoll_ctl(EPOLL_CTL_DISABLE)
: [2] If the return status from epoll_ctl(EPOLL_CTL_DISABLE)
: was zero, then the file descriptor can be safely
: deleted by the thread that made this call.
: [3] If the epoll_ctl(EPOLL_CTL_DISABLE) fails with EBUSY,
: then the descriptor is in use. In this case, the calling
: thread should set a flag in the user-space cache to
: indicate that the thread that is using the descriptor
: should perform the deletion operation.
:
: Is all of the above correct?
:
: The implementation depends on checking on whether
: (events & ~EP_PRIVATE_BITS) == 0
: This replies on the fact that EPOLL_CTL_AD and EPOLL_CTL_MOD always
: set EPOLLHUP and EPOLLERR in the 'events' mask, and EPOLLONESHOT
: causes those flags (as well as all others in ~EP_PRIVATE_BITS) to be
: cleared.
:
: A corollary to the previous paragraph is that using EPOLL_CTL_DISABLE
: is only useful in conjunction with EPOLLONESHOT. However, as things
: stand, one can use EPOLL_CTL_DISABLE on a file descriptor that does
: not have EPOLLONESHOT set in 'events' This results in the following
: (slightly surprising) behavior:
:
: (a) The first call to epoll_ctl(EPOLL_CTL_DISABLE) returns 0
: (the indicator that the file descriptor can be safely deleted).
: (b) The next call to epoll_ctl(EPOLL_CTL_DISABLE) fails with EBUSY.
:
: This doesn't seem particularly useful, and in fact is probably an
: indication that the user made a logic error: they should only be using
: epoll_ctl(EPOLL_CTL_DISABLE) on a file descriptor for which
: EPOLLONESHOT was set in 'events'. If that is correct, then would it
: not make sense to return an error to user space for this case?
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: "Paton J. Lewis" <palewis@adobe.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The of_device_id match data is now marked as const and
must not be modified. This changes the dw_mmc to mark
all pointers passing the dw_mci_drv_data or dw_mci_dma_ops
structures as const, and also marks the static definitions
as const.
drivers/mmc/host/dw_mmc-exynos.c: In function 'dw_mci_exynos_probe':
drivers/mmc/host/dw_mmc-exynos.c:234:11: warning: assignment discards 'const' qualifier from pointer target type [enabled by default]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
CMD23 causes lots of errors in kernel on some freescale SoCs
(P1020, P1021, P1022, P1024, P1025 and P4080) when MMC card used,
which is because these controllers does not support CMD23,
even on the SoCs which declares CMD23 is supported.
Therefore, we'll not use CMD23.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Even though platform_get_irq returns error, 'host->irq'
always has an unsigned value. Less-than-zero comparison
of an unsigned value is never true. Type of 'unsigned int'
will be changed for 'int'.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
ocp2scp was not having pdata support which makes *musb* fail for non-dt
boot in OMAP platform. The pdata will have information about the devices
that is connected to ocp2scp. ocp2scp driver will now make use of this
information to create the devices that is attached to ocp2scp.
This is needed to fix MUSB regression caused by commit c9e4412a
(arm: omap: phy: remove unused functions from omap-phy-internal.c)
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
[tony@atomide.com: updated comments for regression info]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Makes it easier to troubleshoot in the field.
Acked-by: Ian Campbell <ian.campbell@citrix.com>
[v1: Use macro per Ian's suggestion]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
The driver does not expose any custom API to userspace and none of the standard
static code checker tools report any issues, so move it out of staging.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patch updates the adjfreq callback description to include a note that the
delta in ppb is always relative to the base frequency, and not to the current
frequency of the hardware clock.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
CC: stable@vger.kernel.org [v3.5+]
CC: Richard Cochran <richard.cochran@gmail.com>
CC: John Stultz <john.stultz@linaro.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
"First post-Sandy pull request"
1) Fix antenna gain handling and initialization of chan->max_reg_power
in wireless, from Felix Fietkau.
2) Fix nexthop handling in H.232 conntrack helper, from Julian
Anastasov.
3) Only process 80211 mesh config header in certain kinds of frames,
from Javier Cardona.
4) 80211 management frame header length needs to be validated, from
Johannes Berg.
5) Don't access free'd SKBs in ath9k driver, from Felix Fietkay.
6) Test for permanent state correctly in VXLAN driver, from Stephen
Hemminger.
7) BNX2X bug fixes from Yaniv Rosner and Dmitry Kravkov.
8) Fix off by one errors in bonding, from Nikolay ALeksandrov.
9) Fix divide by zero in TCP-Illinois congestion control. From Jesper
Dangaard Brouer.
10) TCP metrics code says "Yo dawg, I heard you like sizeof, so I did a
sizeof of a sizeof, so you can size your size" Fix from Julian
Anastasov.
11) Several drivers do mdiobus_free without first doing an
mdiobus_unregister leading to stray pointer references. Fix from
Peter Senna Tschudin.
12) Fix OOPS in l2tp_eth_create() error path, it's another danling
pointer kinda situation. Fix from Tom Parkin.
13) Hardware driven by the vmxnet driver can't handle larger than 16K
fragments, so split them up when necessary. From Eric Dumazet.
14) Handle zero length data length in tcp_send_rcvq() properly. Fix
from Pavel Emelyanov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
tcp-repair: Handle zero-length data put in rcv queue
vmxnet3: must split too big fragments
l2tp: fix oops in l2tp_eth_create() error path
cxgb4: Fix unable to get UP event from the LLD
drivers/net/phy/mdio-bitbang.c: Call mdiobus_unregister before mdiobus_free
drivers/net/ethernet/nxp/lpc_eth.c: Call mdiobus_unregister before mdiobus_free
bnx2x: fix HW initialization using fw 7.8.x
tcp: Fix double sizeof in new tcp_metrics code
net: fix divide by zero in tcp algorithm illinois
net: sctp: Fix typo in net/sctp
bonding: fix second off-by-one error
bonding: fix off-by-one error
bnx2x: Disable FCoE for 57840 since not yet supported by FW
bnx2x: Fix no link on 577xx 10G-baseT
bnx2x: Fix unrecognized SFP+ module after driver is loaded
bnx2x: Fix potential incorrect link speed provision
bnx2x: Restore global registers back to default.
bnx2x: Fix link down in 57712 following LFA
bnx2x: Fix 57810 1G-KR link against certain switches.
ixgbe: PTP get_ts_info missing software support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen bugfixes from Konrad Rzeszutek Wilk:
- Use appropriate macros instead of hand-rolling our own (ARM).
- Fixes if FB/KBD closed unexpectedly.
- Fix memory leak in /dev/gntdev ioctl calls.
- Fix overflow check in xenbus_file_write.
- Document cleanup.
- Performance optimization when migrating guests.
* tag 'stable/for-linus-3.7-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/mmu: Use Xen specific TLB flush instead of the generic one.
xen/arm: use the __HVC macro
xen/xenbus: fix overflow check in xenbus_file_write()
xen-kbdfront: handle backend CLOSED without CLOSING
xen-fbfront: handle backend CLOSED without CLOSING
xen/gntdev: don't leak memory from IOCTL_GNTDEV_MAP_GRANT_REF
x86: remove obsolete comment from asm/xen/hypervisor.h
|
|
This hashtable implementation is using hlist buckets to provide a simple
hashtable to prevent it from getting reimplemented all over the kernel.
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
[ Merging this now, so that subsystems can start applying Sasha's
patches that use this - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull KVM fix from Marcelo Tosatti.
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: fix vcpu->mmio_fragments overflow
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This contains unexpectedly many changes in a wide range due to the
fixes for races at disconnection of USB audio devices. In the end, we
end up covering fairly core parts of sound subsystem.
Other than that, just a few usual small fixes."
* tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: ice1724: Fix rate setup after resume
ALSA: Avoid endless sleep after disconnect
ALSA: Add a reference counter to card instance
ALSA: usb-audio: Fix races at disconnection in mixer_quirks.c
ALSA: usb-audio: Use rwsem for disconnect protection
ALSA: usb-audio: Fix races at disconnection
ALSA: PCM: Fix some races at disconnection
ASoC: omap-dmic: Correct functional clock name
ASoC: zoom2: Fix compile error by including correct header files
ALSA: hda - Fix mute-LED setup for HP dv5 laptop
|
|
After commit b3356bf0dbb349 (KVM: emulator: optimize "rep ins" handling),
the pieces of io data can be collected and write them to the guest memory
or MMIO together
Unfortunately, kvm splits the mmio access into 8 bytes and store them to
vcpu->mmio_fragments. If the guest uses "rep ins" to move large data, it
will cause vcpu->mmio_fragments overflow
The bug can be exposed by isapc (-M isapc):
[23154.818733] general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC
[ ......]
[23154.858083] Call Trace:
[23154.859874] [<ffffffffa04f0e17>] kvm_get_cr8+0x1d/0x28 [kvm]
[23154.861677] [<ffffffffa04fa6d4>] kvm_arch_vcpu_ioctl_run+0xcda/0xe45 [kvm]
[23154.863604] [<ffffffffa04f5a1a>] ? kvm_arch_vcpu_load+0x17b/0x180 [kvm]
Actually, we can use one mmio_fragment to store a large mmio access then
split it when we pass the mmio-exit-info to userspace. After that, we only
need two entries to store mmio info for the cross-mmio pages access
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
As Mukesh explained it, the MMUEXT_TLB_FLUSH_ALL allows the
hypervisor to do a TLB flush on all active vCPUs. If instead
we were using the generic one (which ends up being xen_flush_tlb)
we end up making the MMUEXT_TLB_FLUSH_LOCAL hypercall. But
before we make that hypercall the kernel will IPI all of the
vCPUs (even those that were asleep from the hypervisor
perspective). The end result is that we needlessly wake them
up and do a TLB flush when we can just let the hypervisor
do it correctly.
This patch gives around 50% speed improvement when migrating
idle guest's from one host to another.
Oracle-bug: 14630170
CC: stable@vger.kernel.org
Tested-by: Jingjie Jiang <jingjie.jiang@oracle.com>
Suggested-by: Mukesh Rathor <mukesh.rathor@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Pull md fixes from NeilBrown:
"Some fixes for md in 3.7
- one recently introduced crash for dm-raid10 with discard
- one bug in new functionality that has been around for a few
releases.
- minor bug in md's 'faulty' personality
and UAPI disintegration for md."
* tag 'md-3.7-fixes' of git://neil.brown.name/md:
MD RAID10: Fix oops when creating RAID10 arrays via dm-raid.c
md/raid1: Fix assembling of arrays containing Replacements.
md faulty: use disk_stack_limits()
UAPI: (Scripted) Disintegrate include/linux/raid
|
|
Remove usage of plat/cpu.h and get information from platform data
instead. This enables omapdrm to be built with ARCH_MULTIPLATFORM.
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
