| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next
John W. Linville says:
====================
This is a batch of updates intended for 3.12. It is mostly driver
stuff, although Johannes Berg and Simon Wunderlich make a good
showing with mac80211 bits (particularly some work on 5/10 MHz
channel support).
The usual suspects are mostly represented. There are lots of updates
to iwlwifi, ath9k, ath10k, mwifiex, rt2x00, wil6210, as usual.
The bcma bus gets some love this time, as do cw1200, iwl4965, and a
few other bits here and there. I don't think there is much unusual
here, FWIW.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pptp driver has lots of byte order warnings from sparse.
This was because the on-the-wire header is in network byte order (obviously)
but the definition did not reflect that.
Also, the address structure to user space actually put the call id
in host order. Rather than break ABI compatibility, just acknowledge
the existing design.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
Conflicts:
drivers/net/ethernet/broadcom/Kconfig
|
|
Adding paged frags skbs to af_unix sockets introduced a performance
regression on large sends because of additional page allocations, even
if each skb could carry at least 100% more payload than before.
We can instruct sock_alloc_send_pskb() to attempt high order
allocations.
Most of the time, it does a single page allocation instead of 8.
I added an additional parameter to sock_alloc_send_pskb() to
let other users to opt-in for this new feature on followup patches.
Tested:
Before patch :
$ netperf -t STREAM_STREAM
STREAM STREAM TEST
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
2304 212992 212992 10.00 46861.15
After patch :
$ netperf -t STREAM_STREAM
STREAM STREAM TEST
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
2304 212992 212992 10.00 57981.11
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
unix_stream_sendmsg() currently uses order-2 allocations,
and we had numerous reports this can fail.
The __GFP_REPEAT flag present in sock_alloc_send_pskb() is
not helping.
This patch extends the work done in commit eb6a24816b247c
("af_unix: reduce high order page allocations) for
datagram sockets.
This opens the possibility of zero copy IO (splice() and
friends)
The trick is to not use skb_pull() anymore in recvmsg() path,
and instead add a @consumed field in UNIXCB() to track amount
of already read payload in the skb.
There is a performance regression for large sends
because of extra page allocations that will be addressed
in a follow-up patch, allowing sock_alloc_send_pskb()
to attempt high order page allocations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Encrypt the cookie with both server and client IPv4 addresses,
such that multi-homed server will grant different cookies
based on both the source and destination IPs. No client change
is needed since cookie is opaque to the client.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit cda5f98e36576596b9230483ec52bff3cc97eb21.
As per Vlad's request.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
|
|
With the restructuring of the lksctp.org site, we only allow bug
reports through the SCTP mailing list linux-sctp@vger.kernel.org,
not via SF, as SF is only used for web hosting and nothing more.
While at it, also remove the obvious statement that bugs will be
fixed and incooperated into the kernel.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Get rid of the last module parameter for SCTP and make this
configurable via sysctl for SCTP like all the rest of SCTP's
configuration knobs.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds the new procfs knobs:
/proc/sys/net/ipv4/conf/*/igmpv2_unsolicited_report_interval
/proc/sys/net/ipv4/conf/*/igmpv3_unsolicited_report_interval
Which will allow userspace configuration of the IGMP unsolicited report
interval (see below) in milliseconds. The defaults are 10000ms for IGMPv2
and 1000ms for IGMPv3 in accordance with RFC2236 and RFC3376.
Background:
If an IGMP join packet is lost you will not receive data sent to the
multicast group so if no data arrives from that multicast group in a
period of time after the IGMP join a second IGMP join will be sent. The
delay between joins is the "IGMP Unsolicited Report Interval".
Prior to this patch this value was hard coded in the kernel to 10s for
IGMPv2 and 1s for IGMPv3. 10s is unsuitable for some use-cases, such as
IPTV as it can cause channel change to be slow in the presence of packet
loss.
This patch allows the value to be overridden from userspace for both
IGMPv2 and IGMPv3 such that it can be tuned accoding to the network.
Tested with Wireshark and a simple program to join a (non-existent)
multicast group. The distribution of timings for the second join differ
based upon setting the procfs knobs.
igmpvX_unsolicited_report_interval is intended to follow the pattern
established by force_igmp_version, and while a procfs entry has been added
a corresponding sysctl knob has not as it is my understanding that sysctl
is deprecated[1].
[1]: http://lwn.net/Articles/247243/
Signed-off-by: William Manley <william.manley@youview.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The procfs knob /proc/sys/net/ipv4/conf/*/force_igmp_version allows the
IGMP protocol version to use to be explicitly set. As a side effect this
caused the routing cache to be flushed as it was declared as a
DEVINET_SYSCTL_FLUSHING_ENTRY. Flushing is unnecessary and this patch
makes it so flushing does not occur.
Requested by Hannes Frederic Sowa as he was reviewing other patches
adding procfs entries.
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: William Manley <william.manley@youview.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With GRO/LRO processing, there is a problem because Ip[6]InReceives SNMP
counters do not count the number of frames, but number of aggregated
segments.
Its probably too late to change this now.
This patch adds four new counters, tracking number of frames, regardless
of LRO/GRO, and on a per ECN status basis, for IPv4 and IPv6.
Ip[6]NoECTPkts : Number of packets received with NOECT
Ip[6]ECT1Pkts : Number of packets received with ECT(1)
Ip[6]ECT0Pkts : Number of packets received with ECT(0)
Ip[6]CEPkts : Number of packets received with Congestion Experienced
lph37:~# nstat | egrep "Pkts|InReceive"
IpInReceives 1634137 0.0
Ip6InReceives 3714107 0.0
Ip6InNoECTPkts 19205 0.0
Ip6InECT0Pkts 52651828 0.0
IpExtInNoECTPkts 33630 0.0
IpExtInECT0Pkts 15581379 0.0
IpExtInCEPkts 6 0.0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To let it be reused and reduce code duplication. Also document this function.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To let it be reused and reduce code duplication.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IP tunnel hash heads can be embedded in the per-net structure
since it is a fixed size. Reduce the size so that the total structure
fits in a page size. The original size was overly large, even NETDEV_HASHBITS
is only 8 bits!
Also, add some white space for readability.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Pravin B Shelar <pshelar@nicira.com>.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As dst_cookie is used in fast path sctp_transport_dst_check.
Before:
struct sctp_transport {
struct list_head transports; /* 0 16 */
atomic_t refcnt; /* 16 4 */
__u32 dead:1; /* 20:31 4 */
__u32 rto_pending:1; /* 20:30 4 */
__u32 hb_sent:1; /* 20:29 4 */
__u32 pmtu_pending:1; /* 20:28 4 */
/* XXX 28 bits hole, try to pack */
__u32 sack_generation; /* 24 4 */
/* XXX 4 bytes hole, try to pack */
struct flowi fl; /* 32 64 */
/* --- cacheline 1 boundary (64 bytes) was 32 bytes ago --- */
union sctp_addr ipaddr; /* 96 28 */
After:
struct sctp_transport {
struct list_head transports; /* 0 16 */
atomic_t refcnt; /* 16 4 */
__u32 dead:1; /* 20:31 4 */
__u32 rto_pending:1; /* 20:30 4 */
__u32 hb_sent:1; /* 20:29 4 */
__u32 pmtu_pending:1; /* 20:28 4 */
/* XXX 28 bits hole, try to pack */
__u32 sack_generation; /* 24 4 */
u32 dst_cookie; /* 28 4 */
struct flowi fl; /* 32 64 */
/* --- cacheline 1 boundary (64 bytes) was 32 bytes ago --- */
union sctp_addr ipaddr; /* 96 28 */
Signed-off-by: Fan Du <fan.du@windriver.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge net into net-next to setup some infrastructure Eric
Dumazet needs for usbnet changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Don't ignore user initiated wireless regulatory settings on cards
with custom regulatory domains, from Arik Nemtsov.
2) Fix length check of bluetooth information responses, from Jaganath
Kanakkassery.
3) Fix misuse of PTR_ERR in btusb, from Adam Lee.
4) Handle rfkill properly while iwlwifi devices are offline, from
Emmanuel Grumbach.
5) Fix r815x devices DMA'ing to stack buffers, from Hayes Wang.
6) Kernel info leak in ATM packet scheduler, from Dan Carpenter.
7) 8139cp doesn't check for DMA mapping errors, from Neil Horman.
8) Fix bridge multicast code to not snoop when no querier exists,
otherwise mutlicast traffic is lost. From Linus Lüssing.
9) Avoid soft lockups in fib6_run_gc(), from Michal Kubecek.
10) Fix races in automatic address asignment on ipv6, which can result
in incorrect lifetime assignments. From Jiri Benc.
11) Cure build bustage when CONFIG_NET_LL_RX_POLL is not set and rename
it CONFIG_NET_RX_BUSY_POLL to eliminate the last reference to the
original naming of this feature. From Cong Wang.
12) Fix crash in TIPC when server socket creation fails, from Ying Xue.
13) macvlan_changelink() silently succeeds when it shouldn't, from
Michael S Tsirkin.
14) HTB packet scheduler can crash due to sign extension, fix from
Stephen Hemminger.
15) With the cable unplugged, r8169 prints out a message every 10
seconds, make it netif_dbg() instead of netif_warn(). From Peter
Wu.
16) Fix memory leak in rtm_to_ifaddr(), from Daniel Borkmann.
17) sis900 gets spurious TX queue timeouts due to mismanagement of link
carrier state, from Denis Kirjanov.
18) Validate somaxconn sysctl to make sure it fits inside of a u16.
From Roman Gushchin.
19) Fix MAC address filtering on qlcnic, from Shahed Shaikh.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (68 commits)
qlcnic: Fix for flash update failure on 83xx adapter
qlcnic: Fix link speed and duplex display for 83xx adapter
qlcnic: Fix link speed display for 82xx adapter
qlcnic: Fix external loopback test.
qlcnic: Removed adapter series name from warning messages.
qlcnic: Free up memory in error path.
qlcnic: Fix ingress MAC learning
qlcnic: Fix MAC address filter issue on 82xx adapter
net: ethernet: davinci_emac: drop IRQF_DISABLED
netlabel: use domain based selectors when address based selectors are not available
net: check net.core.somaxconn sysctl values
sis900: Fix the tx queue timeout issue
net: rtm_to_ifaddr: free ifa if ifa_cacheinfo processing fails
r8169: remove "PHY reset until link up" log spam
net: ethernet: cpsw: drop IRQF_DISABLED
htb: fix sign extension bug
macvlan: handle set_promiscuity failures
macvlan: better mode validation
tipc: fix oops when creating server socket fails
net: rename CONFIG_NET_LL_RX_POLL to CONFIG_NET_RX_BUSY_POLL
...
|
|
Move refcnt, pref, suppress_ifgroup, suppress_prefixlen out of first
cache line, as they are not used in fast path.
Make sure ctarget & fr_net are in first cache line.
(Assuming 64 bit arches and 64 bytes cache lines)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change brings the suppressor attribute names into line; it also changes
the data types to provide a more consistent interface.
While -1 indicates that the suppressor is not enabled, values >= 0 for
suppress_prefixlen or suppress_ifgroup reject routing decisions violating the
constraint.
This changes the previously presented behaviour of suppress_prefixlen, where a
prefix length _less_ than the attribute value was rejected. After this change,
a prefix length less than *or* equal to the value is considered a violation of
the rule constraint.
It also changes the default values for default and newly added rules (disabling
any suppression for those).
Signed-off-by: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change adds the ability to suppress a routing decision based upon the
interface group the selected interface belongs to. This allows it to
exclude specific devices from a routing decision.
Signed-off-by: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma fixes from Roland Dreier:
- Fixes for the newly merged mlx5 hardware driver
- Stack info leak fixes from Dan Carpenter
- Fixes for pkey table handling with SR-IOV
- A few other small things
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Fix pkey change flow for virtualization environments
IPoIB: Make sure child devices use valid/proper pkeys
IB/core: Create QP1 using the pkey index which contains the default pkey
mlx5_core: Variable may be used uninitialized
mlx5_core: Implement new initialization sequence
mlx5_core: Fix use after free in mlx5_cmd_comp_handler()
IB/mlx5: Fix stack info leak in mlx5_ib_alloc_ucontext()
IB/mlx5: Fix error return code in init_one()
IB/mlx4: Use default pkey when creating tunnel QPs
RDMA/cma: Only call cma_save_ib_info() for CM REQs
RDMA/cma: Fix accessing invalid private data for UD
RDMA/cma: Fix gcc warning
Revert "RDMA/nes: Fix compilation error when nes_debug is enabled"
IB/qib: Add err_decode() call for ring dump
RDMA/cxgb3: Fix stack info leak in iwch_create_cq()
RDMA/nes: Fix info leaks in nes_create_qp() and nes_create_cq()
RDMA/ocrdma: Fix several stack info leaks
RDMA/cxgb4: Fix stack info leak in c4iw_create_qp()
RDMA/ocrdma: Remove unused include
|
|
When sctp sits on IPv6, sctp_transport_dst_check pass cookie as ZERO,
as a result ip6_dst_check always fail out. This behaviour makes
transport->dst useless, because every sctp_packet_transmit must look
for valid dst.
Add a dst_cookie into sctp_transport, and set the cookie whenever we
get new dst for sctp_transport. So dst validness could be checked
against it.
Since I have split genid for IPv4 and IPv6, also delete/add IPv6 address
will also bump IPv6 genid. So issues we discussed in:
http://marc.info/?l=linux-netdev&m=137404469219410&w=4
have all been sloved for this patch.
Signed-off-by: Fan Du <fan.du@windriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's convenient to have ethernet mac addresses use
ETH_ALEN to be able to grep for them a bit easier and
also to ensure that the addresses are __aligned(2).
Add #include <linux/if_ether.h> as necessary.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the #define where appropriate.
Add #include <linux/if_ether.h>
where appropriate too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- Revert two cpuidle commits added during the 3.8 development cycle
that turn out to have introduced a significant performance regression
as requested by Jeremy Eder.
- The recent patches that made the freezer less heavy-weight introduced
a regression causing user-space-driven hibernation using the ioctl()
interface to block indefinitely when the hibernate process executes
try_to_freeze(). Fix from Colin Cross addresses this by adding a
process flag to mark the hibernate/suspend process to inform the
freezer that that process should be ignored.
- One of the recent cpufreq reverts uncovered a problem in the core
causing the cpufreq driver module refcount to become negative after a
system suspend-resume cycle. Fix from Rafael J Wysocki.
- The evaluation of the ACPI battery _BIX method has never worked
correctly, because the commit that added support for it forgot to
take the "Revision" field in the return package into account. As a
result, the reading of battery info doesn't work at all on some
systems, which is addressed by a fix from Lan Tianyu.
* tag 'pm+acpi-3.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
freezer: set PF_SUSPEND_TASK flag on tasks that call freeze_processes
ACPI / battery: Fix parsing _BIX return value
cpufreq: Fix cpufreq driver module refcount balance after suspend/resume
Revert "cpuidle: Quickly notice prediction failure for repeat mode"
Revert "cpuidle: Quickly notice prediction failure in general case"
|
|
Eliezer renames several *ll_poll to *busy_poll, but forgets
CONFIG_NET_LL_RX_POLL, so in case of confusion, rename it too.
Cc: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When CONFIG_NET_LL_RX_POLL is not set, I got:
net/socket.c: In function ‘sock_poll’:
net/socket.c:1165:4: error: implicit declaration of function ‘sk_busy_loop’ [-Werror=implicit-function-declaration]
Fix this by adding a nop when !CONFIG_NET_LL_RX_POLL.
Cc: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On a high-traffic router with many processors and many IPv6 dst
entries, soft lockup in fib6_run_gc() can occur when number of
entries reaches gc_thresh.
This happens because fib6_run_gc() uses fib6_gc_lock to allow
only one thread to run the garbage collector but ip6_dst_gc()
doesn't update net->ipv6.ip6_rt_last_gc until fib6_run_gc()
returns. On a system with many entries, this can take some time
so that in the meantime, other threads pass the tests in
ip6_dst_gc() (ip6_rt_last_gc is still not updated) and wait for
the lock. They then have to run the garbage collector one after
another which blocks them for quite long.
Resolve this by replacing special value ~0UL of expire parameter
to fib6_run_gc() by explicit "force" parameter to choose between
spin_lock_bh() and spin_trylock_bh() and call fib6_run_gc() with
force=false if gc_thresh is reached but not max_size.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
David suggested to add a BUG_ON() to catch if some layer
sets skb->sk pointer without a corresponding destructor.
As skb can sit in a queue, it's mandatory to make sure the
socket cannot disappear, and it's usually done by taking a
reference on the socket, then releasing it from the skb
destructor.
This patch is a follow-up to commit c34a761231b5
("net: skb_orphan() changes") and will be reverted after
catching all possible offenders if any.
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
The count field in CSA must be decremented with each beacon
transmitted. This patch implements the functionality for drivers
using ieee80211_beacon_get(). Other drivers must call back manually
after reaching count == 0.
This patch also contains the handling and finish worker for the channel
switch command, and mac80211/chanctx code to allow to change a channel
definition of an active channel context.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[small cleanups, catch identical chandef]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
To allow channel switch announcements within beacons, add
the channel switch command to nl80211/cfg80211. This is
implementation is intended for AP and (later) IBSS mode.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add element IDs for Extended BSS Load, VHT TX
Power Envelope, AID, and Quiet Channel.
Signed-off-by: Fred Zhou <fred.zy@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
IEEE802.11u interworking support is advertised via extended
capabilities IE bit 31. This is 7th bit of 4th byte of extended
capabilities.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Pull drm fixes from Dave Airlie:
"Radeon, nouveau, exynos, intel, mgag200..
Not all strictly regressions but there was probably only one patch I'd
have really left out and it didn't seem worth respinning exynos to
avoid it, the line change count is quite low.
radeon: regressions + more dynamic powermanagement fixes, since DPM
is a new feature, and off by default I'd prefer to keep merging
fixes since it has a large userbase already and I'd like to keep
them on mainline
nouveau: is mostly regression fixes
i915: is a regression fix since Daniel is on holidays I've merged it.
mgag200: I've picked a bunch of targetted fixes from a big bunch of
distro patches,
exynos: build fixes mostly, one regression fix
I expect things will slow right down now, I may send on the intel
early quirk from Jesse separatly, since I think the x86 maintainers
acked it"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (37 commits)
drm/i915: fix missed hunk after GT access breakage
drm/radeon/dpm: re-enable cac control on SI
drm/radeon/dpm: fix calculations in si_calculate_leakage_for_v_and_t_formula
drm: fix 64 bit drm fixed point helpers
drm/radeon/atom: initialize more atom interpretor elements to 0
drm/nouveau: fix semaphore dmabuf obj
drm/nouveau/vm: make vm refcount into a kref
drm/nv31/mpeg: don't recognize nv3x cards as having nv44 graph class
drm/nv40/mpeg: write magic value to channel object to make it work
drm/nouveau: fix size check for cards without vm
drm/nv50-/disp: remove dcb_outp_match call, and related variables
drm/nva3-/disp: fix hda eld writing, needs to be padded
drm/nv31/mpeg: fix mpeg engine initialization
drm/nv50/mc: include vp in the fb error reporting mask
drm/nouveau: fix null pointer dereference in poll_changed
drm/nv50/gpio: post-nv92 cards have 32 interrupt lines
drm/nvc0/fb: take lock in nvc0_ram_put()
drm/nouveau/core: xtensa firmware size needs to be 0x40000 no matter what
drm/mgag200: Fix LUT programming for 16bpp
drm/mgag200: Fix framebuffer pitch calculation
...
|
|
Merge more patches from Andrew Morton:
"A bunch of fixes.
Plus Joe's printk move and rework. It's not a -rc3 thing but now
would be a nice time to offload it, while things are quiet. I've been
sitting on it all for a couple of weeks, no issues"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
vmpressure: make sure there are no events queued after memcg is offlined
vmpressure: do not check for pending work to prevent from new work
vmpressure: change vmpressure::sr_lock to spinlock
printk: rename struct log to struct printk_log
printk: use pointer for console_cmdline indexing
printk: move braille console support into separate braille.[ch] files
printk: add console_cmdline.h
printk: move to separate directory for easier modification
drivers/rtc/rtc-twl.c: fix: rtcX/wakealarm attribute isn't created
mm: zbud: fix condition check on allocation size
thp, mm: avoid PageUnevictable on active/inactive lru lists
mm/swap.c: clear PageActive before adding pages onto unevictable list
arch/x86/platform/ce4100/ce4100.c: include reboot.h
mm: sched: numa: fix NUMA balancing when !SCHED_DEBUG
rapidio: fix use after free in rio_unregister_scan()
.gitignore: ignore *.lz4 files
MAINTAINERS: dynamic debug: Jason's not there...
dmi_scan: add comments on dmi_present() and the loop in dmi_scan_machine()
ocfs2/refcounttree: add the missing NULL check of the return value of find_or_create_page()
mm: mempolicy: fix mbind_range() && vma_adjust() interaction
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Reflow modified prototypes to 80 columns.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Reflow modified prototypes to 80 columns.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Reflow modified prototypes to 80 columns.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Reflow modified prototypes to 80 columns.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Reflow modified prototypes to 80 columns.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Reflow modified prototypes to 80 columns.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change adds a new operation to the fib_rules_ops struct; it allows the
suppression of routing decisions if certain criteria are not met by its
results.
The first implemented constraint is a minimum prefix length added to the
structures of routing rules. If a rule is added with a minimum prefix length
>0, only routes meeting this threshold will be considered. Any other (more
general) routing table entries will be ignored.
When configuring a system with multiple network uplinks and default routes, it
is often convinient to reference the main routing table multiple times - but
omitting the default route. Using this patch and a modified "ip" utility, this
can be achieved by using the following command sequence:
$ ip route add table secuplink default via 10.42.23.1
$ ip rule add pref 100 table main prefixlength 1
$ ip rule add pref 150 fwmark 0xA table secuplink
With this setup, packets marked 0xA will be processed by the additional routing
table "secuplink", but only if no suitable route in the main routing table can
be found. By using a minimal prefixlength of 1, the default route (/0) of the
table "main" is hidden to packets processed by rule 100; packets traveling to
destinations with more specific routing entries are processed as usual.
Signed-off-by: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Reflow modified prototypes to 80 columns.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
