| Age | Commit message (Collapse) | Author |
|---|
|
commit 2c45aada341121438affc4cb8d5b4cfaa2813d3d upstream.
In allmodconfig builds for sparc and any other arch which does
not set CONFIG_SPARSE_IRQ, the following will be seen at modpost:
CC [M] lib/cpu-notifier-error-inject.o
CC [M] lib/pm-notifier-error-inject.o
ERROR: "irq_to_desc" [drivers/gpio/gpio-mcp23s08.ko] undefined!
make[2]: *** [__modpost] Error 1
This happens because commit 3911ff30f5 ("genirq: export
handle_edge_irq() and irq_to_desc()") added one export for it, but
there were actually two instances of it, in an if/else clause for
CONFIG_SPARSE_IRQ. Add the second one.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Link: http://lkml.kernel.org/r/1392057610-11514-1-git-send-email-paul.gortmaker@windriver.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 923fa4ea382f592dee2ba3b205befb90cbddf3af upstream.
The generic_chip.c uses interfaces from irq_domain.c which is
controlled by the IRQ_DOMAIN config option, but there is no Kconfig
dependency so the build can fail:
linux/kernel/irq/generic-chip.c:400:11: error:
'irq_domain_xlate_onetwocell' undeclared here (not in a function)
Select IRQ_DOMAIN when GENERIC_IRQ_CHIP is selected.
Signed-off-by: Nitin A Kamble <nitin.a.kamble@intel.com>
Link: http://lkml.kernel.org/r/1391129410-54548-2-git-send-email-nitin.a.kamble@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ac01810c9d2814238f08a227062e66a35a0e1ea2 upstream.
When the system enters suspend, it disables all interrupts in
suspend_device_irqs(), including the interrupts marked EARLY_RESUME.
On the resume side things are different. The EARLY_RESUME interrupts
are reenabled in sys_core_ops->resume and the non EARLY_RESUME
interrupts are reenabled in the normal system resume path.
When suspend_noirq() failed or suspend is aborted for any other
reason, we might omit the resume side call to sys_core_ops->resume()
and therefor the interrupts marked EARLY_RESUME are not reenabled and
stay disabled forever.
To solve this, enable all irqs unconditionally in irq_resume()
regardless whether interrupts marked EARLY_RESUMEhave been already
enabled or not.
This might try to reenable already enabled interrupts in the non
failure case, but the only affected platform is XEN and it has been
confirmed that it does not cause any side effects.
[ tglx: Massaged changelog. ]
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by-and-tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Cc: <ian.campbell@citrix.com>
Cc: <rjw@rjwysocki.net>
Cc: <len.brown@intel.com>
Cc: <gregkh@linuxfoundation.org>
Link: http://lkml.kernel.org/r/1385388587-16442-1-git-send-email-ldewangan@nvidia.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bbfe65c219c638e19f1da5adab1005b2d68ca810 upstream.
In commit ee23871389 ("genirq: Set irq thread to RT priority on
creation") we moved the assigment of the thread's priority from the
thread's function into __setup_irq(). That function may run in user
context for instance if the user opens an UART node and then driver
calls requests in the ->open() callback. That user may not have
CAP_SYS_NICE and so the irq thread won't run with the SCHED_OTHER
policy.
This patch uses sched_setscheduler_nocheck() so we omit the CAP_SYS_NICE
check which is otherwise required for the SCHED_OTHER policy.
[bigeasy: Rewrite the changelog]
Signed-off-by: Thomas Pfaff <tpfaff@pcs.com>
Cc: Ivo Sieben <meltedpianoman@gmail.com>
Link: http://lkml.kernel.org/r/1381489240-29626-1-git-send-email-bigeasy@linutronix.de
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
- core fix for missing round up in the generic irq chip implementation
- new irq chip for MOXA SoCs
- a few fixes and cleanups in the irqchip drivers
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: Add support for MOXA ART SoCs
genirq: generic chip: Use DIV_ROUND_UP to calculate numchips
irqchip: nvic: Fix wrong num_ct argument for irq_alloc_domain_generic_chips()
irqchip: sun4i: Staticize sun4i_irq_ack()
irqchip: vt8500: Staticize local symbols
|
|
Pull MIPS updates from Ralf Baechle:
"MIPS updates:
- All the things that didn't make 3.10.
- Removes the Windriver PPMC platform. Nobody will miss it.
- Remove a workaround from kernel/irq/irqdomain.c which was there
exclusivly for MIPS. Patch by Grant Likely.
- More small improvments for the SEAD 3 platform
- Improvments on the BMIPS / SMP support for the BCM63xx series.
- Various cleanups of dead leftovers.
- Platform support for the Cavium Octeon-based EdgeRouter Lite.
Two large KVM patchsets didn't make it for this pull request because
their respective authors are vacationing"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
MIPS: SEAD3: Disable L2 cache on SEAD-3.
MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
MIPS: BCM63xx: Add SMP support to prom.c
MIPS: define write{b,w,l,q}_relaxed
MIPS: Expose missing pci_io{map,unmap} declarations
MIPS: Malta: Update GCMP detection.
Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
MIPS: APSP: Remove <asm/kspd.h>
SSB: Kconfig: Amend SSB_EMBEDDED dependencies
MIPS: microMIPS: Fix improper definition of ISA exception bit.
MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
MIPS: Declare emulate_load_store_microMIPS as a static function.
MIPS: Fix typos and cleanup comment
MIPS: Cleanup indentation and whitespace
MIPS: BMIPS: support booting from physical CPU other than 0
MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
MIPS: GIC: Fix gic_set_affinity infinite loop
MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
...
|
|
Pull irqdomain refactoring from Grant Likely:
"This is the long awaited simplification of irqdomain. It gets rid of
the different types of irq domains and instead both linear and tree
mappings can be supported in a single domain. Doing this removes a
lot of special case code and makes irq domains simpler to understand
overall"
* tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux:
irq: fix checkpatch error
irqdomain: Include hwirq number in /proc/interrupts
irqdomain: make irq_linear_revmap() a fast path again
irqdomain: remove irq_domain_generate_simple()
irqdomain: Refactor irq_domain_associate_many()
irqdomain: Beef up debugfs output
irqdomain: Clean up aftermath of irq_domain refactoring
irqdomain: Eliminate revmap type
irqdomain: merge linear and tree reverse mappings.
irqdomain: Add a name field
irqdomain: Replace LEGACY mapping with LINEAR
irqdomain: Relax failure path on setting up mappings
|
|
The number of interrupts in a domain may be not divisible by the
number of interrupts each chip handles. Integer division may truncate
the result, thus use DIV_ROUND_UP to count numchips.
Seems all users of irq_alloc_domain_generic_chips() in current code do
not have this issue. I just found the issue while reading the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: http://lkml.kernel.org/r/1373015592.18252.2.camel@phoenix
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree updates from Jiri Kosina:
"The usual stuff from trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
treewide: relase -> release
Documentation/cgroups/memory.txt: fix stat file documentation
sysctl/net.txt: delete reference to obsolete 2.4.x kernel
spinlock_api_smp.h: fix preprocessor comments
treewide: Fix typo in printk
doc: device tree: clarify stuff in usage-model.txt.
open firmware: "/aliasas" -> "/aliases"
md: bcache: Fixed a typo with the word 'arithmetic'
irq/generic-chip: fix a few kernel-doc entries
frv: Convert use of typedef ctl_table to struct ctl_table
sgi: xpc: Convert use of typedef ctl_table to struct ctl_table
doc: clk: Fix incorrect wording
Documentation/arm/IXP4xx fix a typo
Documentation/networking/ieee802154 fix a typo
Documentation/DocBook/media/v4l fix a typo
Documentation/video4linux/si476x.txt fix a typo
Documentation/virtual/kvm/api.txt fix a typo
Documentation/early-userspace/README fix a typo
Documentation/video4linux/soc-camera.txt fix a typo
lguest: fix CONFIG_PAE -> CONFIG_x86_PAE in comment
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core irq changes from Ingo Molnar:
"The main changes:
- generic-irqchip driver additions, cleanups and fixes
- 3 new irqchip drivers: ARMv7-M NVIC, TB10x and Marvell Orion SoCs
- irq_get_trigger_type() simplification and cross-arch cleanup
- various cleanups, simplifications
- documentation updates"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
softirq: Use _RET_IP_
genirq: Add the generic chip to the genirq docbook
genirq: generic-chip: Export some irq_gc_ functions
genirq: Fix can_request_irq() for IRQs without an action
irqchip: exynos-combiner: Staticize combiner_init
irqchip: Add support for ARMv7-M NVIC
irqchip: Add TB10x interrupt controller driver
irqdomain: Use irq_get_trigger_type() to get IRQ flags
MIPS: octeon: Use irq_get_trigger_type() to get IRQ flags
arm: orion: Use irq_get_trigger_type() to get IRQ flags
mfd: stmpe: use irq_get_trigger_type() to get IRQ flags
mfd: twl4030-irq: Use irq_get_trigger_type() to get IRQ flags
gpio: mvebu: Use irq_get_trigger_type() to get IRQ flags
genirq: Add irq_get_trigger_type() to get IRQ flags
genirq: Irqchip: document gcflags arg of irq_alloc_domain_generic_chips
genirq: Set irq thread to RT priority on creation
irqchip: Add support for Marvell Orion SoCs
genirq: Add kerneldoc for irq_disable.
genirq: irqchip: Add mask to block out invalid irqs
genirq: Generic chip: Add linear irq domain support
...
|
|
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Randy Dunlap <rdunlap@infradead.org>
|
|
When building imx_v6_v7_defconfig with imx-drm drivers selected as
modules, we get the following build errors:
ERROR: "irq_gc_mask_clr_bit" [drivers/staging/imx-drm/ipu-v3/imx-ipu-v3.ko] undefined!
ERROR: "irq_gc_mask_set_bit" [drivers/staging/imx-drm/ipu-v3/imx-ipu-v3.ko] undefined!
ERROR: "irq_gc_ack_set_bit" [drivers/staging/imx-drm/ipu-v3/imx-ipu-v3.ko] undefined!
Export the required functions to avoid this problem.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: shawn.guo@linaro.org
Cc: kernel@pengutronix.de
Link: http://lkml.kernel.org/r/1372389789-7048-1-git-send-email-festevam@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Commit 02725e7471b8 ('genirq: Use irq_get/put functions'),
inadvertently changed can_request_irq() to return 0 for IRQs that have
no action. This causes pcibios_lookup_irq() to select only IRQs that
already have an action with IRQF_SHARED set, or to fail if there are
none. Change can_request_irq() to return 1 for IRQs that have no
action (if the first two conditions are met).
Reported-by: Bjarni Ingi Gislason <bjarniig@rhi.hi.is>
Tested-by: Bjarni Ingi Gislason <bjarniig@rhi.hi.is> (against 3.2)
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: 709647@bugs.debian.org
Cc: stable@vger.kernel.org # 2.6.39+
Link: http://bugs.debian.org/709647
Link: http://lkml.kernel.org/r/1372383630.23847.40.camel@deadeye.wl.decadent.org.uk
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Use irq_get_trigger_type() to get the IRQ trigger type flags
instead calling irqd_get_trigger_type(irq_desc_get_irq_data(virq))
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mips@linux-mips.org
Link: http://lkml.kernel.org/r/1371228049-27080-8-git-send-email-javier.martinez@collabora.co.uk
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Commit 088f40b7b027dad6519712ff224a5798dd62a204 ("genirq: Generic chip:
Add linear irq domain support") missed kerneldoc for the gcflags
argument of irq_alloc_domain_generic_chips(). Add it now.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Link: http://lkml.kernel.org/r/1371564513-4327-1-git-send-email-james.hogan@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
ERROR: space required before the open parenthesis '('
WARNING: Prefer pr_warn(... to pr_warning(...
Just fix above 2 issue.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
|
Add the hardware interrupt number to the output of /proc/interrupts.
It is often important to have access to the hardware interrupt number because
it identifies exactly how an interrupt signal is wired up to the interrupt
controller. This is especially important when using irq_domains since irq
numbers get dynamically allocated in that case, and have no relation to the
actual hardware number.
Note: This output is currently conditional on whether or not the irq_domain
pointer is set; however hwirq could still be used without irq_domain. It
may be worthwhile to always output the hwirq number regardless of the
domain pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Olof Johansson <olof@lixom.net>
Cc: Ben Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
|
|
Over the years, irq_linear_revmap() gained tests and checks to make sure
callers were using it safely, which while important, also make it less
of a fast path. After the irqdomain refactoring done recently, it is now
possible to make irq_linear_revmap() a fast path again. This patch moves
irq_linear_revmap() to the header file and makes it a static inline so
that interrupt controller drivers using a linear mapping can decode the
virq from a hwirq in just a couple of instructions.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
|
Nobody calls it; remove the function
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
|
Originally, irq_domain_associate_many() was designed to unwind the
mapped irqs on a failure of any individual association. However, that
proved to be a problem with certain IRQ controllers. Some of them only
support a subset of irqs, and will fail when attempting to map a
reserved IRQ. In those cases we want to map as many IRQs as possible, so
instead it is better for irq_domain_associate_many() to make a
best-effort attempt to map irqs, but not fail if any or all of them
don't succeed. If a caller really cares about how many irqs got
associated, then it should instead go back and check that all of the
irqs is cares about were mapped.
The original design open-coded the individual association code into the
body of irq_domain_associate_many(), but with no longer needing to
unwind associations, the code becomes simpler to split out
irq_domain_associate() to contain the bulk of the logic, and
irq_domain_associate_many() to be a simple loop wrapper.
This patch also adds a new error check to the associate path to make
sure it isn't called for an irq larger than the controller can handle,
and adds locking so that the irq_domain_mutex is held while setting up a
new association.
v3: Fixup missing change to irq_domain_add_tree()
v2: Fixup x86 warning. irq_domain_associate_many() no longer returns an
error code, but reports errors to the printk log directly. In the
majority of cases we don't actually want to fail if there is a
problem, but rather log it and still try to boot the system.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
irqdomain: Fix flubbed irq_domain_associate_many refactoring
commit d39046ec72, "irqdomain: Refactor irq_domain_associate_many()" was
missing the following hunk which causes a boot failure on anything using
irq_domain_add_tree() to allocate an irq domain.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>,
Cc: Thomas Gleixner <tglx@linutronix.de>,
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
|
|
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The MIPS interrupt controllers are all registering their own irq_domains
now. Drop the MIPS specific code because it is no longer needed.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5458/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
When a threaded irq handler is installed the irq thread is initially
created on normal scheduling priority. Only after the irq thread is
woken up it sets its priority to RT_FIFO MAX_USER_RT_PRIO/2 itself.
This means that interrupts that occur directly after the irq handler
is installed will be handled on a normal scheduling priority instead
of the realtime priority that one would expect.
Fix this by setting the RT priority on creation of the irq_thread.
Signed-off-by: Ivo Sieben <meltedpianoman@gmail.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/1370254322-17240-1-git-send-email-meltedpianoman@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This patch increases the amount of output produced by the
irq_domain_mapping debugfs file by first listing all of the registered
irq domains at the beginning of the output, and then by including all
mapped IRQs in the output, not just the active ones. It is very useful
when debugging irqdomain issues to be able to see the entire list of
mapped irqs, not just the ones that happen to be connected to devices.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
|
After refactoring the irqdomain code, there are a number of API
functions that are merely empty wrappers around core code. Drop those
wrappers out of the C file and replace them with static inlines in the
header.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
|
The NOMAP irq_domain type is only used by a handful of interrupt
controllers and it unnecessarily complicates the code by adding special
cases on how to look up mappings and different revmap functions are used
for each type which need to validate the correct type is passed to it
before performing the reverse map. Eliminating the revmap_type and
making a single reverse mapping function simplifies the code. It also
shouldn't be any slower than having separate revmap functions because
the type of the revmap needed to be checked anyway.
The linear and tree revmap types were already merged in a previous
patch. This patch rolls the NOMAP or direct mapping behaviour into the
same domain code making is possible for an irq domain to do any mapping
type; linear, tree or direct; and that the mapping will be transparent
to the interrupt controller driver.
With this change, direct mappings will get stored in the linear or tree
mapping for consistency. Reverse mapping from the hwirq to virq will go
through the normal lookup process. However, any controller using a
direct mapping can take advantage of knowing that hwirq==virq for any
mapped interrupts skip doing a revmap lookup when handling IRQs.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
|
Keeping them separate makes irq_domain more complex and adds a lot of
code (as proven by the diffstat). Merging them simplifies the whole
scheme. This change makes it so both the tree and linear methods can be
used by the same irq_domain instance. If the hwirq is less than the
->linear_size, then the linear map is used to reverse map the hwirq.
Otherwise the radix tree is used. The test for which map to use is no
more expensive that the existing code, so the performance of fast path
is preserved.
It also means that complex interrupt controllers can use both the
linear map and a tree in the same domain. This may be useful for an
interrupt controller with a base set of core irqs and a large number
of GPIOs which might be used as irqs. The linear map could cover the
core irqs, and the tree used for thas irqs. The linear map could
cover the core irqs, and the tree used for the gpios.
v2: Drop reorganization of revmap data
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
|
|
This patch adds a name field to the irq_domain structure to help mere
mortals understand the mappings between irq domains and virqs. It also
converts a number of places that have open-coded some kind of fudging
an irqdomain name to use the new field. This means a more consistent
display of names in irq domain log messages and debugfs output.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
|
The LEGACY mapping unnecessarily complicates the irqdomain code and
can easily be implemented with a linear mapping. By ripping it out
and replacing it with the LINEAR mapping the object size of
irqdomain.c shrinks by about 330 bytes (ARMv7) which offsets the
additional allocation required by the linear map. It also makes it
possible for current LEGACY map users to pre-allocate irq_descs for a
subset of the hwirqs and dynamically allocate the rest as needed.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
|
|
Commit 98aa468e, "irqdomain: Support for static IRQ mapping and
association" introduced an API for directly associating blocks of hwirqs
to linux irqs. However, if any irq in that block failed to map (say if
the mapping functions returns an error because the irq is already
mapped) then the whole thing will fail and roll back. This is probably
too aggressive since there are valid reasons why a mapping may fail.
ie. Firmware may have a particular IRQ marked as unusable.
This patch drops the error path out of irq_domain_associate(). If a
mapping fails, then it is simply skipped. There is no reason to fail the
entire allocation.
v2: Still output an information message on failed mappings and make sure
attempted mapping gets cleared out of the irq_data structure.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
|
|
|
|
The first_irq needs to be zero to get a linear domain and that
comes with special semantics. We want to simplify this going
forward but some documentation never hurts.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
|
Since irq_data may be NULL, if so, we WARN_ON(), and continue, 'hwirq'
which related with 'irq_data' has to initialize later, or it will cause
issue.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
|
All other irq_domain_add_* functions are exported already, and apparently
this one got left out by mistake, which causes build errors for ARM
allmodconfig kernels:
ERROR: "irq_domain_add_simple" [drivers/gpio/gpio-rcar.ko] undefined!
ERROR: "irq_domain_add_simple" [drivers/gpio/gpio-em.ko] undefined!
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
|
Document the lazy disable functionality. comment based on changelog of
d209a699a0b975ad
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Cc: balbi@ti.com
Link: http://lkml.kernel.org/r/1368181290-1583-1-git-send-email-andreas.fenkart@streamunlimited.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Some controllers have irqs that aren't wired up and must never be used.
For the generic chip attached to an irq_domain this provides a mask that
can be used to block out particular irqs so that they never get mapped.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Link: http://lkml.kernel.org/r/1369793454-19197-2-git-send-email-grant.likely@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Provide infrastructure for irq chip implementations which work on
linear irq domains.
- Interface to allocate multiple generic chips which are associated to
the irq domain.
- Interface to get the generic chip pointer for a particular hardware
interrupt in the domain.
- irq domain mapping function to install the chip for a particular
interrupt.
Note: This lacks a removal function for now.
[ Sebastian Hesselbarth: Mask cache and pointer math fixups ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jean-Francois Moine <moinejf@free.fr>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Rob Landley <rob@landley.net>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20130506142539.450634298@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Preparatory patch for linear interrupt domains.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jean-Francois Moine <moinejf@free.fr>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Rob Landley <rob@landley.net>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20130506142539.377017672@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Some chips have weird bit mask access patterns instead of the linear
you expect. Allow them to calculate the cached mask themself.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jean-Francois Moine <moinejf@free.fr>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Rob Landley <rob@landley.net>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20130506142539.302898834@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Cache the per irq bit mask instead of recalculating it over and over.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jean-Francois Moine <moinejf@free.fr>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Rob Landley <rob@landley.net>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20130506142539.227119865@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
There are cases where all irq_chip_type instances have separate mask
registers, making a shared mask register cache unsuitable for the
purpose.
Introduce a new flag IRQ_GC_MASK_CACHE_PER_TYPE. If set, point the per
chip mask pointer to the per chip private mask cache instead.
[ tglx: Simplified code, renamed flag and massaged changelog ]
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Joey Oravec <joravec@drewtech.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Holger Brunck <Holger.Brunck@keymile.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Simon Guinot <simon@sequanux.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jean-Francois Moine <moinejf@free.fr>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Rob Landley <rob@landley.net>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: http://lkml.kernel.org/r/20130506142539.152569748@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Today the same interrupt mask cache (stored within struct irq_chip_generic)
is shared between all the irq_chip_type instances. As there are instances
where each irq_chip_type uses a distinct mask register (as it is the case
for Orion SoCs), sharing a single mask cache may be incorrect.
So add a distinct pointer for each irq_chip_type, which for now
points to the original mask register within irq_chip_generic.
So no functional changes here.
[ tglx: Minor cosmetic tweaks ]
Reported-by: Joey Oravec <joravec@drewtech.com>
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Holger Brunck <Holger.Brunck@keymile.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Simon Guinot <simon@sequanux.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jean-Francois Moine <moinejf@free.fr>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Rob Landley <rob@landley.net>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: http://lkml.kernel.org/r/20130506142539.082226607@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Since we already have an irq_data_get_chip_type() function which returns
a pointer to irq_chip_type, use that instead of cur_regs().
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Joey Oravec <joravec@drewtech.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Holger Brunck <Holger.Brunck@keymile.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Simon Guinot <simon@sequanux.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jean-Francois Moine <moinejf@free.fr>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Rob Landley <rob@landley.net>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: http://lkml.kernel.org/r/20130506142539.010164766@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Some interrupt controllers refuse to map interrupts marked as
"protected" by firwmare. Since we try to map everyting in the
device-tree on some platforms, we end up with a lot of nasty
WARN's in the boot log for what is a normal situation on those
machines.
This defines a specific return code (-EPERM) from the host map()
callback which cause irqdomain to fail silently.
MPIC is updated to return this when hitting a protected source
printing only a single line message for diagnostic purposes.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Supply a function (proc_remove()) to remove a proc entry (and any subtree
rooted there) by proc_dir_entry pointer rather than by name and (optionally)
root dir entry pointer. This allows us to eliminate all remaining pde->name
accesses outside of procfs.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Grant Likely <grant.likely@linaro.or>
cc: linux-acpi@vger.kernel.org
cc: openipmi-developer@lists.sourceforge.net
cc: devicetree-discuss@lists.ozlabs.org
cc: linux-pci@vger.kernel.org
cc: netdev@vger.kernel.org
cc: netfilter-devel@vger.kernel.org
cc: alsa-devel@alsa-project.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
The only part of proc_dir_entry the code outside of fs/proc
really cares about is PDE(inode)->data. Provide a helper
for that; static inline for now, eventually will be moved
to fs/proc, along with the knowledge of struct proc_dir_entry
layout.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86/apic changes from Ingo Molnar:
"Main changes:
- Multiple MSI support added to the APIC, PCI and AHCI code - acked
by all relevant maintainers, by Alexander Gordeev.
The advantage is that multiple AHCI ports can have multiple MSI
irqs assigned, and can thus spread to multiple CPUs.
[ Drivers can make use of this new facility via the
pci_enable_msi_block_auto() method ]
- x86 IOAPIC code from interrupt remapping cleanups from Joerg
Roedel:
These patches move all interrupt remapping specific checks out of
the x86 core code and replaces the respective call-sites with
function pointers. As a result the interrupt remapping code is
better abstraced from x86 core interrupt handling code.
- Various smaller improvements, fixes and cleanups."
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
x86/intel/irq_remapping: Clean up x2apic opt-out security warning mess
x86, kvm: Fix intialization warnings in kvm.c
x86, irq: Move irq_remapped out of x86 core code
x86, io_apic: Introduce eoi_ioapic_pin call-back
x86, msi: Introduce x86_msi.compose_msi_msg call-back
x86, irq: Introduce setup_remapped_irq()
x86, irq: Move irq_remapped() check into free_remapped_irq
x86, io-apic: Remove !irq_remapped() check from __target_IO_APIC_irq()
x86, io-apic: Move CONFIG_IRQ_REMAP code out of x86 core
x86, irq: Add data structure to keep AMD specific irq remapping information
x86, irq: Move irq_remapping_enabled declaration to iommu code
x86, io_apic: Remove irq_remapping_enabled check in setup_timer_IRQ0_pin
x86, io_apic: Move irq_remapping_enabled checks out of check_timer()
x86, io_apic: Convert setup_ioapic_entry to function pointer
x86, io_apic: Introduce set_affinity function pointer
x86, msi: Use IRQ remapping specific setup_msi_irqs routine
x86, hpet: Introduce x86_msi_ops.setup_hpet_msi
x86, io_apic: Introduce x86_io_apic_ops.print_entries for debugging
x86, io_apic: Introduce x86_io_apic_ops.disable()
x86, apic: Mask IO-APIC and PIC unconditionally on LAPIC resume
...
|
