Age | Commit message (Collapse) | Author |
|
The advantage of kcalloc is, that will prevent integer overflows which could
result from the multiplication of number of elements and size and it is also
a bit nicer to read.
The semantic patch that makes this change is available
in https://lkml.org/lkml/2011/11/25/107
Link: http://lkml.kernel.org/r/1322600880.1534.347.camel@localhost.localdomain
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Currently the ftrace_set_filter and ftrace_set_notrace functions
do not return any return code. So there's no way for ftrace_ops
user to tell wether the filter was correctly applied.
The set_ftrace_filter interface returns error in case the filter
did not match:
# echo krava > set_ftrace_filter
bash: echo: write error: Invalid argument
Changing both ftrace_set_filter and ftrace_set_notrace functions
to return zero if the filter was applied correctly or -E* values
in case of error.
Link: http://lkml.kernel.org/r/1325495060-6402-2-git-send-email-jolsa@redhat.com
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Change set_ftrace_early_filter() to ftrace_set_early_filter()
and make it a global function. This will allow other subsystems
in the kernel to be able to enable function tracing at start
up and reuse the ftrace function parsing code.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
The set_ftrace_filter shows "hashed" functions, which are functions
that are added with operations to them (like traceon and traceoff).
As other subsystems may be able to show what functions they are
using for function tracing, the hash items should no longer
be shown just because the FILTER flag is set. As they have nothing
to do with other subsystems filters.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
The function tracer is set up to allow any other subsystem (like perf)
to use it. Ftrace already has a way to list what functions are enabled
by the global_ops. It would be very helpful to let other users of
the function tracer to be able to use the same code.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
There are two types of hashes in the ftrace_ops; one type
is the filter_hash and the other is the notrace_hash. Either
one may be null, meaning it has no elements. But when elements
are added, the hash is allocated.
Throughout the code, a check needs to be made to see if a hash
exists or the hash has elements, but the check if the hash exists
is usually missing causing the possible "NULL pointer dereference bug".
Add a helper routine called "ftrace_hash_empty()" that returns
true if the hash doesn't exist or its count is zero. As they mean
the same thing.
Last-bug-reported-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
When disabling the "notrace" records, that means we want to trace them.
If the notrace_hash is zero, it means that we want to trace all
records. But to disable a zero notrace_hash means nothing.
The check for the notrace_hash count was incorrect with:
if (hash && !hash->count)
return
With the correct comment above it that states that we do nothing
if the notrace_hash has zero count. But !hash also means that
the notrace hash has zero count. I think this was done to
protect against dereferencing NULL. But if !hash is true, then
we go through the following loop without doing a single thing.
Fix it to:
if (!hash || !hash->count)
return;
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Now that each set of pages in the function list are sorted by
ip, we can use bsearch to find a record within each set of pages.
This speeds up the ftrace_location() function by magnitudes.
For archs (like x86) that need to add a breakpoint at every function
that will be converted from a nop to a callback and vice versa,
the breakpoint callback needs to know if the breakpoint was for
ftrace or not. It requires finding the breakpoint ip within the
records. Doing a linear search is extremely inefficient. It is
a must to be able to do a fast binary search to find these locations.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Sort records by ip locations of the ftrace mcount calls on each of the
set of pages in the function list. This helps in localizing cache
usuage when updating the function locations, as well as gives us
the ability to quickly find an ip location in the list.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
As new functions come in to be initalized from mcount to nop,
they are done by groups of pages. Whether it is the core kernel
or a module. There's no need to keep track of these on a per record
basis.
At startup, and as any module is loaded, the functions to be
traced are stored in a group of pages and added to the function
list at the end. We just need to keep a pointer to the first
page of the list that was added, and use that to know where to
start on the list for initializing functions.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Allocate the mcount record pages as a group of pages as big
as can be allocated and waste no more than a single page.
Grouping the mcount pages as much as possible helps with cache
locality, as we do not need to redirect with descriptors as we
cross from page to page. It also allows us to do more with the
records later on (sort them with bigger benefits).
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Records that are added to the function trace table are
permanently there, except for modules. By separating out the
modules to their own pages that can be freed in one shot
we can remove the "freed" flag and simplify some of the record
management.
Another benefit of doing this is that we can also move the
records around; sort them.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
The stop machine method to modify all functions in the kernel
(some 20,000 of them) is the safest way to do so across all archs.
But some archs may not need this big hammer approach to modify code
on SMP machines, and can simply just update the code it needs.
Adding a weak function arch_ftrace_update_code() that now does the
stop machine, will also let any arch override this method.
If the arch needs to check the system and then decide if it can
avoid stop machine, it can still call ftrace_run_stop_machine() to
use the old method.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Multiple users of the function tracer can register their functions
with the ftrace_ops structure. The accounting within ftrace will
update the counter on each function record that is being traced.
When the ftrace_ops filtering adds or removes functions, the
function records will be updated accordingly if the ftrace_ops is
still registered.
When a ftrace_ops is removed, the counter of the function records,
that the ftrace_ops traces, are decremented. When they reach zero
the functions that they represent are modified to stop calling the
mcount code.
When changes are made, the code is updated via stop_machine() with
a command passed to the function to tell it what to do. There is an
ENABLE and DISABLE command that tells the called function to enable
or disable the functions. But the ENABLE is really a misnomer as it
should just update the records, as records that have been enabled
and now have a count of zero should be disabled.
The DISABLE command is used to disable all functions regardless of
their counter values. This is the big off switch and is not the
complement of the ENABLE command.
To make matters worse, when a ftrace_ops is unregistered and there
is another ftrace_ops registered, neither the DISABLE nor the
ENABLE command are set when calling into the stop_machine() function
and the records will not be updated to match their counter. A command
is passed to that function that will update the mcount code to call
the registered callback directly if it is the only one left. This
means that the ftrace_ops that is still registered will have its callback
called by all functions that have been set for it as well as the ftrace_ops
that was just unregistered.
Here's a way to trigger this bug. Compile the kernel with
CONFIG_FUNCTION_PROFILER set and with CONFIG_FUNCTION_GRAPH not set:
CONFIG_FUNCTION_PROFILER=y
# CONFIG_FUNCTION_GRAPH is not set
This will force the function profiler to use the function tracer instead
of the function graph tracer.
# cd /sys/kernel/debug/tracing
# echo schedule > set_ftrace_filter
# echo function > current_tracer
# cat set_ftrace_filter
schedule
# cat trace
# tracer: nop
#
# entries-in-buffer/entries-written: 692/68108025 #P:4
#
# _-----=> irqs-off
# / _----=> need-resched
# | / _---=> hardirq/softirq
# || / _--=> preempt-depth
# ||| / delay
# TASK-PID CPU# |||| TIMESTAMP FUNCTION
# | | | |||| | |
kworker/0:2-909 [000] .... 531.235574: schedule <-worker_thread
<idle>-0 [001] .N.. 531.235575: schedule <-cpu_idle
kworker/0:2-909 [000] .... 531.235597: schedule <-worker_thread
sshd-2563 [001] .... 531.235647: schedule <-schedule_hrtimeout_range_clock
# echo 1 > function_profile_enabled
# echo 0 > function_porfile_enabled
# cat set_ftrace_filter
schedule
# cat trace
# tracer: function
#
# entries-in-buffer/entries-written: 159701/118821262 #P:4
#
# _-----=> irqs-off
# / _----=> need-resched
# | / _---=> hardirq/softirq
# || / _--=> preempt-depth
# ||| / delay
# TASK-PID CPU# |||| TIMESTAMP FUNCTION
# | | | |||| | |
<idle>-0 [002] ...1 604.870655: local_touch_nmi <-cpu_idle
<idle>-0 [002] d..1 604.870655: enter_idle <-cpu_idle
<idle>-0 [002] d..1 604.870656: atomic_notifier_call_chain <-enter_idle
<idle>-0 [002] d..1 604.870656: __atomic_notifier_call_chain <-atomic_notifier_call_chain
The same problem could have happened with the trace_probe_ops,
but they are modified with the set_frace_filter file which does the
update at closure of the file.
The simple solution is to change ENABLE to UPDATE and call it every
time an ftrace_ops is unregistered.
Link: http://lkml.kernel.org/r/1323105776-26961-3-git-send-email-jolsa@redhat.com
Cc: stable@vger.kernel.org # 3.0+
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace into perf/core
|
|
If the set_ftrace_filter is cleared by writing just whitespace to
it, then the filter hash refcounts will be decremented but not
updated. This causes two bugs:
1) No functions will be enabled for tracing when they all should be
2) If the users clears the set_ftrace_filter twice, it will crash ftrace:
------------[ cut here ]------------
WARNING: at /home/rostedt/work/git/linux-trace.git/kernel/trace/ftrace.c:1384 __ftrace_hash_rec_update.part.27+0x157/0x1a7()
Modules linked in:
Pid: 2330, comm: bash Not tainted 3.1.0-test+ #32
Call Trace:
[<ffffffff81051828>] warn_slowpath_common+0x83/0x9b
[<ffffffff8105185a>] warn_slowpath_null+0x1a/0x1c
[<ffffffff810ba362>] __ftrace_hash_rec_update.part.27+0x157/0x1a7
[<ffffffff810ba6e8>] ? ftrace_regex_release+0xa7/0x10f
[<ffffffff8111bdfe>] ? kfree+0xe5/0x115
[<ffffffff810ba51e>] ftrace_hash_move+0x2e/0x151
[<ffffffff810ba6fb>] ftrace_regex_release+0xba/0x10f
[<ffffffff8112e49a>] fput+0xfd/0x1c2
[<ffffffff8112b54c>] filp_close+0x6d/0x78
[<ffffffff8113a92d>] sys_dup3+0x197/0x1c1
[<ffffffff8113a9a6>] sys_dup2+0x4f/0x54
[<ffffffff8150cac2>] system_call_fastpath+0x16/0x1b
---[ end trace 77a3a7ee73794a02 ]---
Link: http://lkml.kernel.org/r/20111101141420.GA4918@debian
Reported-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
A forced undef of a config value was used for testing and was
accidently left in during the final commit. This causes x86 to
run slower than needed while running function tracing as well
as causes the function graph selftest to fail when DYNMAIC_FTRACE
is not set. This is because the code in MCOUNT expects the ftrace
code to be processed with the config value set that happened to
be forced not set.
The forced config option was left in by:
commit 6331c28c962561aee59e5a493b7556a4bb585957
ftrace: Fix dynamic selftest failure on some archs
Link: http://lkml.kernel.org/r/20111102150255.GA6973@debian
Cc: stable@vger.kernel.org
Reported-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
These files are doing things like module_put and try_module_get
so they need to call out the module.h for explicit inclusion,
rather than getting it via <linux/device.h> which we ideally want
to remove the module.h inclusion from.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
As the function tracer is very intrusive, lots of self checks are
performed on the tracer and if something is found to be strange
it will shut itself down keeping it from corrupting the rest of the
kernel. This shutdown may still allow functions to be traced, as the
tracing only stops new modifications from happening. Trying to stop
the function tracer itself can cause more harm as it requires code
modification.
Although a WARN_ON() is executed, a user may not notice it. To help
the user see that something isn't right with the tracing of the system
a big warning is added to the output of the tracer that lets the user
know that their data may be incomplete.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-2.6-trace into perf/core
|
|
Merge reason: pick up the latest fixes - they won't make v3.0.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Enabling function tracer to trace all functions, then load a module and
then disable function tracing will cause ftrace to fail.
This can also happen by enabling function tracing on the command line:
ftrace=function
and during boot up, modules are loaded, then you disable function tracing
with 'echo nop > current_tracer' you will trigger a bug in ftrace that
will shut itself down.
The reason is, the new ftrace code keeps ref counts of all ftrace_ops that
are registered for tracing. When one or more ftrace_ops are registered,
all the records that represent the functions that the ftrace_ops will
trace have a ref count incremented. If this ref count is not zero,
when the code modification runs, that function will be enabled for tracing.
If the ref count is zero, that function will be disabled from tracing.
To make sure the accounting was working, FTRACE_WARN_ON()s were added
to updating of the ref counts.
If the ref count hits its max (> 2^30 ftrace_ops added), or if
the ref count goes below zero, a FTRACE_WARN_ON() is triggered which
disables all modification of code.
Since it is common for ftrace_ops to trace all functions in the kernel,
instead of creating > 20,000 hash items for the ftrace_ops, the hash
count is just set to zero, and it represents that the ftrace_ops is
to trace all functions. This is where the issues arrise.
If you enable function tracing to trace all functions, and then add
a module, the modules function records do not get the ref count updated.
When the function tracer is disabled, all function records ref counts
are subtracted. Since the modules never had their ref counts incremented,
they go below zero and the FTRACE_WARN_ON() is triggered.
The solution to this is rather simple. When modules are loaded, and
their functions are added to the the ftrace pool, look to see if any
ftrace_ops are registered that trace all functions. And for those,
update the ref count for the module function records.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Archs that do not implement CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST, will
fail the dynamic ftrace selftest.
The function tracer has a quick 'off' variable that will prevent
the call back functions from being called. This variable is called
function_trace_stop. In x86, this is implemented directly in the mcount
assembly, but for other archs, an intermediate function is used called
ftrace_test_stop_func().
In dynamic ftrace, the function pointer variable ftrace_trace_function is
used to update the caller code in the mcount caller. But for archs that
do not have CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST set, it only calls
ftrace_test_stop_func() instead, which in turn calls __ftrace_trace_function.
When more than one ftrace_ops is registered, the function it calls is
ftrace_ops_list_func(), which will iterate over all registered ftrace_ops
and call the callbacks that have their hash matching.
The issue happens when two ftrace_ops are registered for different functions
and one is then unregistered. The __ftrace_trace_function is then pointed
to the remaining ftrace_ops callback function directly. This mean it will
be called for all functions that were registered to trace by both ftrace_ops
that were registered.
This is not an issue for archs with CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST,
because the update of ftrace_trace_function doesn't happen until after all
functions have been updated, and then the mcount caller is updated. But
for those archs that do use the ftrace_test_stop_func(), the update is
immediate.
The dynamic selftest fails because it hits this situation, and the
ftrace_ops that it registers fails to only trace what it was suppose to
and instead traces all other functions.
The solution is to delay the setting of __ftrace_trace_function until
after all the functions have been updated according to the registered
ftrace_ops. Also, function_trace_stop is set during the update to prevent
function tracing from calling code that is caused by the function tracer
itself.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Currently, if set_ftrace_filter() is called when the ftrace_ops is
active, the function filters will not be updated. They will only be updated
when tracing is disabled and re-enabled.
Update the functions immediately during set_ftrace_filter().
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Whenever the hash of the ftrace_ops is updated, the record counts
must be balance. This requires disabling the records that are set
in the original hash, and then enabling the records that are set
in the updated hash.
Moving the update into ftrace_hash_move() removes the bug where the
hash was updated but the records were not, which results in ftrace
triggering a warning and disabling itself because the ftrace_ops filter
is updated while the ftrace_ops was registered, and then the failure
happens when the ftrace_ops is unregistered.
The current code will not trigger this bug, but new code will.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
When I mounted an NFS directory, it caused several modules to be loaded. At the
time I was running the preemptirqsoff tracer, and it showed the following
output:
# tracer: preemptirqsoff
#
# preemptirqsoff latency trace v1.1.5 on 2.6.33.9-rt30-mrg-test
# --------------------------------------------------------------------
# latency: 1177 us, #4/4, CPU#3 | (M:preempt VP:0, KP:0, SP:0 HP:0 #P:4)
# -----------------
# | task: modprobe-19370 (uid:0 nice:0 policy:0 rt_prio:0)
# -----------------
# => started at: ftrace_module_notify
# => ended at: ftrace_module_notify
#
#
# _------=> CPU#
# / _-----=> irqs-off
# | / _----=> need-resched
# || / _---=> hardirq/softirq
# ||| / _--=> preempt-depth
# |||| /_--=> lock-depth
# |||||/ delay
# cmd pid |||||| time | caller
# \ / |||||| \ | /
modprobe-19370 3d.... 0us!: ftrace_process_locs <-ftrace_module_notify
modprobe-19370 3d.... 1176us : ftrace_process_locs <-ftrace_module_notify
modprobe-19370 3d.... 1178us : trace_hardirqs_on <-ftrace_module_notify
modprobe-19370 3d.... 1178us : <stack trace>
=> ftrace_process_locs
=> ftrace_module_notify
=> notifier_call_chain
=> __blocking_notifier_call_chain
=> blocking_notifier_call_chain
=> sys_init_module
=> system_call_fastpath
That's over 1ms that interrupts are disabled on a Real-Time kernel!
Looking at the cause (being the ftrace author helped), I found that the
interrupts are disabled before the code modification of mcounts into nops. The
interrupts only need to be disabled on start up around this code, not when
modules are being loaded.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
The new code that allows different utilities to pick and choose
what functions they trace broke the :mod: hook that allows users
to trace only functions of a particular module.
The reason is that the :mod: hook bypasses the hash that is setup
to allow individual users to trace their own functions and uses
the global hash directly. But if the global hash has not been
set up, it will cause a bug:
echo '*:mod:radeon' > /sys/kernel/debug/set_ftrace_filter
produces:
[drm:drm_mode_getfb] *ERROR* invalid framebuffer id
[drm:radeon_crtc_page_flip] *ERROR* failed to reserve new rbo buffer before flip
BUG: unable to handle kernel paging request at ffffffff8160ec90
IP: [<ffffffff810d9136>] add_hash_entry+0x66/0xd0
PGD 1a05067 PUD 1a09063 PMD 80000000016001e1
Oops: 0003 [#1] SMP Jul 7 04:02:28 phyllis kernel: [55303.858604] CPU 1
Modules linked in: cryptd aes_x86_64 aes_generic binfmt_misc rfcomm bnep ip6table_filter hid radeon r8169 ahci libahci mii ttm drm_kms_helper drm video i2c_algo_bit intel_agp intel_gtt
Pid: 10344, comm: bash Tainted: G WC 3.0.0-rc5 #1 Dell Inc. Inspiron N5010/0YXXJJ
RIP: 0010:[<ffffffff810d9136>] [<ffffffff810d9136>] add_hash_entry+0x66/0xd0
RSP: 0018:ffff88003a96bda8 EFLAGS: 00010246
RAX: ffff8801301735c0 RBX: ffffffff8160ec80 RCX: 0000000000306ee0
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff880137c92940
RBP: ffff88003a96bdb8 R08: ffff880137c95680 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000000 R12: ffffffff81c9df78
R13: ffff8801153d1000 R14: 0000000000000000 R15: 0000000000000000
FS: 00007f329c18a700(0000) GS:ffff880137c80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffffff8160ec90 CR3: 000000003002b000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process bash (pid: 10344, threadinfo ffff88003a96a000, task ffff88012fcfc470)
Stack:
0000000000000fd0 00000000000000fc ffff88003a96be38 ffffffff810d92f5
ffff88011c4c4e00 ffff880000000000 000000000b69f4d0 ffffffff8160ec80
ffff8800300e6f06 0000000081130295 0000000000000282 ffff8800300e6f00
Call Trace:
[<ffffffff810d92f5>] match_records+0x155/0x1b0
[<ffffffff810d940c>] ftrace_mod_callback+0xbc/0x100
[<ffffffff810dafdf>] ftrace_regex_write+0x16f/0x210
[<ffffffff810db09f>] ftrace_filter_write+0xf/0x20
[<ffffffff81166e48>] vfs_write+0xc8/0x190
[<ffffffff81167001>] sys_write+0x51/0x90
[<ffffffff815c7e02>] system_call_fastpath+0x16/0x1b
Code: 48 8b 33 31 d2 48 85 f6 75 33 49 89 d4 4c 03 63 08 49 8b 14 24 48 85 d2 48 89 10 74 04 48 89 42 08 49 89 04 24 4c 89 60 08 31 d2
RIP [<ffffffff810d9136>] add_hash_entry+0x66/0xd0
RSP <ffff88003a96bda8>
CR2: ffffffff8160ec90
---[ end trace a5d031828efdd88e ]---
Reported-by: Brian Marete <marete@toshnix.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-2.6-trace into perf/core
|
|
This patch replaces the code for getting an unsigned long from a
userspace buffer by a simple call to kstroul_from_user.
This makes it easier to read and less error prone.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Link: http://lkml.kernel.org/r/1307476707-14762-1-git-send-email-peterhuewe@gmx.de
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Removed <asm/ftrace.h> because <linux/ftrace.h> was already declared.
Braces of struct's coding style fixed.
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Paul McQuade <tungstentide@gmail.com>
Link: http://lkml.kernel.org/r/4DE59711.3090900@gmail.com
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Revert the commit that removed the disabling of interrupts around
the initial modifying of mcount callers to nops, and update the comment.
The original comment was outdated and stated that the interrupts were
being disabled to prevent kstop machine, which was required with the
old ftrace daemon, but was no longer the case.
What the comment failed to mention was that interrupts needed to be
disabled to keep interrupts from preempting the modifying of the code
and then executing the code that was partially modified.
Revert the commit and update the comment.
Reported-by: Richard W.M. Jones <rjones@redhat.com>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
kernel/trace/ftrace.c: In function 'ftrace_regex_write.clone.15':
kernel/trace/ftrace.c:2743:6: warning: 'ret' may be used uninitialized in this
function
Signed-off-by: GuoWen Li <guowen.li.linux@gmail.com>
Link: http://lkml.kernel.org/r/201106011918.47939.guowen.li.linux@gmail.com
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Witold reported a reboot caused by the selftests of the dynamic function
tracer. He sent me a config and I used ktest to do a config_bisect on it
(as my config did not cause the crash). It pointed out that the problem
config was CONFIG_PROVE_RCU.
What happened was that if multiple callbacks are attached to the
function tracer, we iterate a list of callbacks. Because the list is
managed by synchronize_sched() and preempt_disable, the access to the
pointers uses rcu_dereference_raw().
When PROVE_RCU is enabled, the rcu_dereference_raw() calls some
debugging functions, which happen to be traced. The tracing of the debug
function would then call rcu_dereference_raw() which would then call the
debug function and then... well you get the idea.
I first wrote two different patches to solve this bug.
1) add a __rcu_dereference_raw() that would not do any checks.
2) add notrace to the offending debug functions.
Both of these patches worked.
Talking with Paul McKenney on IRC, he suggested to add recursion
detection instead. This seemed to be a better solution, so I decided to
implement it. As the task_struct already has a trace_recursion to detect
recursion in the ring buffer, and that has a very small number it
allows, I decided to use that same variable to add flags that can detect
the recursion inside the infrastructure of the function tracer.
I plan to change it so that the task struct bit can be checked in
mcount, but as that requires changes to all archs, I will hold that off
to the next merge window.
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/1306348063.1465.116.camel@gandalf.stny.rr.com
Reported-by: Witold Baryluk <baryluk@smp.if.uj.edu.pl>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
When dynamic ftrace is not configured, the ops->flags still needs
to have its FTRACE_OPS_FL_ENABLED bit set in ftrace_startup().
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
The register_ftrace_function() returns an error code on failure
except if the call to ftrace_startup() fails. Add a error return to
ftrace_startup() if it fails to start, allowing register_ftrace_funtion()
to return a proper error value.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Since users of the function tracer can now pick and choose which
functions they want to trace agnostically from other users of the
function tracer, we need to pass the ops struct to the ftrace_set_filter()
functions.
The functions ftrace_set_global_filter() and ftrace_set_global_notrace()
is added to keep the old filter functions which are used to modify
the generic function tracers.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Now that functions may be selected individually, it only makes sense
that we should allow dynamically allocated trace structures to
be traced. This will allow perf to allocate a ftrace_ops structure
at runtime and use it to pick and choose which functions that
structure will trace.
Note, a dynamically allocated ftrace_ops will always be called
indirectly instead of being called directly from the mcount in
entry.S. This is because there's no safe way to prevent mcount
from being preempted before calling the function, unless we
modify every entry.S to do so (not likely). Thus, dynamically allocated
functions will now be called by the ftrace_ops_list_func() that
loops through the ops that are allocated if there are more than
one op allocated at a time. This loop is protected with a
preempt_disable.
To determine if an ftrace_ops structure is allocated or not, a new
util function was added to the kernel/extable.c called
core_kernel_data(), which returns 1 if the address is between
_sdata and _edata.
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
ftrace_ops that are registered to trace functions can now be
agnostic to each other in respect to what functions they trace.
Each ops has their own hash of the functions they want to trace
and a hash to what they do not want to trace. A empty hash for
the functions they want to trace denotes all functions should
be traced that are not in the notrace hash.
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
When a hash is modified and might be in use, we need to perform
a schedule RCU operation on it, as the hashes will soon be used
directly in the function tracer callback.
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
This is a step towards each ops structure defining its own set
of functions to trace. As the current code with pid's and such
are specific to the global_ops, it is restructured to be used
with the global ops.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
In order to allow different ops to enable different functions,
the ftrace_startup() and ftrace_shutdown() functions need the
ops parameter passed to them.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Add the enabled_functions file that is used to show all the
functions that have been enabled for tracing as well as their
ref counts. This helps seeing if any function has been registered
and what functions are being traced.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Every function has its own record that stores the instruction
pointer and flags for the function to be traced. There are only
two flags: enabled and free. The enabled flag states that tracing
for the function has been enabled (actively traced), and the free
flag states that the record no longer points to a function and can
be used by new functions (loaded modules).
These flags are now moved to the MSB of the flags (actually just
the top 32bits). The rest of the bits (30 bits) are now used as
a ref counter. Everytime a tracer register functions to trace,
those functions will have its counter incremented.
When tracing is enabled, to determine if a function should be traced,
the counter is examined, and if it is non-zero it is set to trace.
When a ftrace_ops is registered to trace functions, its hashes
are examined. If the ftrace_ops filter_hash count is zero, then
all functions are set to be traced, otherwise only the functions
in the hash are to be traced. The exception to this is if a function
is also in the ftrace_ops notrace_hash. Then that function's counter
is not incremented for this ftrace_ops.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
When filtering, allocate a hash to insert the function records.
After the filtering is complete, assign it to the ftrace_ops structure.
This allows the ftrace_ops structure to have a much smaller array of
hash buckets instead of wasting a lot of memory.
A read only empty_hash is created to be the minimum size that any ftrace_ops
can point to.
When a new hash is created, it has the following steps:
o Allocate a default hash.
o Walk the function records assigning the filtered records to the hash
o Allocate a new hash with the appropriate size buckets
o Move the entries from the default hash to the new hash.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Combine the filter and notrace hashes to be accessed by a single entity,
the global_ops. The global_ops is a ftrace_ops structure that is passed
to different functions that can read or modify the filtering of the
function tracer.
The ftrace_ops structure was modified to hold a filter and notrace
hashes so that later patches may allow each ftrace_ops to have its own
set of rules to what functions may be filtered.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
When multiple users are allowed to have their own set of functions
to trace, having the FTRACE_FL_FILTER flag will not be enough to
handle the accounting of those users. Each user will need their own
set of functions.
Replace the FTRACE_FL_FILTER with a filter_hash instead. This is
temporary until the rest of the function filtering accounting
gets in.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
To prepare for the accounting system that will allow multiple users of
the function tracer, having the FTRACE_FL_NOTRACE as a flag in the
dyn_trace record does not make sense.
All ftrace_ops will soon have a hash of functions they should trace
and not trace. By making a global hash of functions not to trace makes
this easier for the transition.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-2.6-trace into perf/core
|
|
The code used for matching functions is almost identical between normal
selecting of functions and using the :mod: feature of set_ftrace_notrace.
Consolidate the two users into one function.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
There are three locations that perform almost identical functions in order
to update the ftrace_trace_function (the ftrace function variable that gets
called by mcount).
Consolidate these into a single function called update_ftrace_function().
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|