| Age | Commit message (Collapse) | Author |
|---|
|
ingress being not used very much, and net_device->ingress_queue being
quite a big object (128 or 256 bytes), use a dynamic allocation if
needed (tc qdisc add dev eth0 ingress ...)
dev_ingress_queue(dev) helper should be used only with RTNL taken.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
net/ipv4/Kconfig
net/ipv4/tcp_timer.c
|
|
While doing stress tests with IP route cache disabled, and multi queue
devices, I noticed a very high contention on one rwlock used in
neighbour code.
When many cpus are trying to send frames (possibly using a high
performance multiqueue device) to the same neighbour, they fight for the
neigh->lock rwlock in order to call neigh_hh_init(), and fight on
hh->hh_refcnt (a pair of atomic_inc/atomic_dec_and_test())
But we dont need to call neigh_hh_init() for dst that are used only
once. It costs four atomic operations at least, on two contended cache
lines, plus the high contention on neigh->lock rwlock.
Introduce a new dst flag, DST_NOCACHE, that is set when dst was not
inserted in route cache.
With the stress test bench, sending 160000000 frames on one neighbour,
results are :
Before patch:
real 2m28.406s
user 0m11.781s
sys 36m17.964s
After patch:
real 1m26.532s
user 0m12.185s
sys 20m3.903s
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the condition (3rd arg) passed to sk_wait_event() in
sk_stream_wait_memory(). The incorrect check in sk_stream_wait_memory()
causes the following soft lockup in tcp_sendmsg() when the global tcp
memory pool has exhausted.
>>> snip <<<
localhost kernel: BUG: soft lockup - CPU#3 stuck for 11s! [sshd:6429]
localhost kernel: CPU 3:
localhost kernel: RIP: 0010:[sk_stream_wait_memory+0xcd/0x200] [sk_stream_wait_memory+0xcd/0x200] sk_stream_wait_memory+0xcd/0x200
localhost kernel:
localhost kernel: Call Trace:
localhost kernel: [sk_stream_wait_memory+0x1b1/0x200] sk_stream_wait_memory+0x1b1/0x200
localhost kernel: [<ffffffff802557c0>] autoremove_wake_function+0x0/0x40
localhost kernel: [ipv6:tcp_sendmsg+0x6e6/0xe90] tcp_sendmsg+0x6e6/0xce0
localhost kernel: [sock_aio_write+0x126/0x140] sock_aio_write+0x126/0x140
localhost kernel: [xfs:do_sync_write+0xf1/0x130] do_sync_write+0xf1/0x130
localhost kernel: [<ffffffff802557c0>] autoremove_wake_function+0x0/0x40
localhost kernel: [hrtimer_start+0xe3/0x170] hrtimer_start+0xe3/0x170
localhost kernel: [vfs_write+0x185/0x190] vfs_write+0x185/0x190
localhost kernel: [sys_write+0x50/0x90] sys_write+0x50/0x90
localhost kernel: [system_call+0x7e/0x83] system_call+0x7e/0x83
>>> snip <<<
What is happening is, that the sk_wait_event() condition passed from
sk_stream_wait_memory() evaluates to true for the case of tcp global memory
exhaustion. This is because both sk_stream_memory_free() and vm_wait are true
which causes sk_wait_event() to *not* call schedule_timeout().
Hence sk_stream_wait_memory() returns immediately to the caller w/o sleeping.
This causes the caller to again try allocation, which again fails and again
calls sk_stream_wait_memory(), and so on.
[ Bug introduced by commit c1cbe4b7ad0bc4b1d98ea708a3fecb7362aa4088
("[NET]: Avoid atomic xchg() for non-error case") -DaveM ]
Signed-off-by: Nagendra Singh Tomar <tomer_iisc@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is some confusion with rx_queue name after RPS, and net drivers
private rx_queue fields.
I suggest to rename "struct net_device"->rx_queue to ingress_queue.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As tunnel devices are going to be lockless, we need to make sure a
misconfigured machine wont enter an infinite loop.
Add a percpu variable, and limit to three the number of stacked xmits.
Reported-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch allows a host to be configured to respond to any address in
a specified range as if it were local, without actually needing to
configure the address on an interface. This is done through routing
table configuration. For instance, to configure a host to respond
to any address in 10.1/16 received on eth0 as a local address we can do:
ip rule add from all iif eth0 lookup 200
ip route add local 10.1/16 dev lo proto kernel scope host src 127.0.0.1 table 200
This host is now reachable by any 10.1/16 address (route lookup on
input for packets received on eth0 can find the route). On output, the
rule will not be matched so that this host can still send packets to
10.1/16 (not sent on loopback). Presumably, external routing can be
configured to make sense out of this.
To make this work, we needed to modify the logic in finding the
interface which is assigned a given source address for output
(dev_ip_find). We perform a normal fib_lookup instead of just a
lookup on the local table, and in the lookup we ignore the input
interface for matching.
This patch is useful to implement IP-anycast for subnets of virtual
addresses.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For RPS, we create a kobject for each RX queue based on the number of
queues passed to alloc_netdev_mq(). However, drivers generally do not
determine the numbers of hardware queues to use until much later, so
this usually represents the maximum number the driver may use and not
the actual number in use.
For TX queues, drivers can update the actual number using
netif_set_real_num_tx_queues(). Add a corresponding function for RX
queues, netif_set_real_num_rx_queues().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sk_attach_filter() and sk_detach_filter() are run with socket locked.
Use the appropriate rcu_dereference_protected() instead of blocking BH,
and rcu_dereference_bh().
There is no point adding BH prevention and memory barrier.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It seems we dont use appropriate refcount increment in an
rcu_read_lock() protected section.
fib_rule_get() might increment a null refcount and bad things could
happen.
While fib_nl_delrule() respects an rcu grace period before calling
fib_rule_put(), fib_rules_cleanup_ops() calls fib_rule_put() without a
grace period.
Note : after this patch, we might avoid the synchronize_rcu() call done
in fib_nl_delrule()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes kernel bugzilla #16603
tcp_sendmsg() truncates iov_len to an 'int' which a 4GB write to write
zero bytes, for example.
There is also the problem higher up of how verify_iovec() works. It
wants to prevent the total length from looking like an error return
value.
However it does this using 'int', but syscalls return 'long' (and
thus signed 64-bit on 64-bit machines). So it could trigger
false-positives on 64-bit as written. So fix it to use 'long'.
Reported-by: Olaf Bonorden <bono@onlinehome.de>
Reported-by: Daniel Büse <dbuese@gmx.de>
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/qlcnic/qlcnic_init.c
net/ipv4/ip_output.c
|
|
Instead of having two places were we allocate dev->_rx, introduce
netif_alloc_rx_queues() helper and call it only from
register_netdevice(), not from alloc_netdev_mq()
Goal is to let drivers change dev->num_rx_queues after allocating netdev
and before registering it.
This also removes a lot of ifdefs in net/core/dev.c
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Automatically allows vlans to get NETIF_F_HIGHDMA if underlying device
supports it.
On 32bit arches (and more precisely if CONFIG_HIGHMEM is enabled), it
can help to reduce cost of illegal_highdma() and __skb_linearize()
calls.
Tested on tg3 , bnx2, bonding, this worked very well.
This is a generalization of a patch provided by Yi Zou & Jeff Kirsher.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have for each socket :
One spinlock (sk_slock.slock)
One rwlock (sk_callback_lock)
Possible scenarios are :
(A) (this is used in net/sunrpc/xprtsock.c)
read_lock(&sk->sk_callback_lock) (without blocking BH)
<BH>
spin_lock(&sk->sk_slock.slock);
...
read_lock(&sk->sk_callback_lock);
...
(B)
write_lock_bh(&sk->sk_callback_lock)
stuff
write_unlock_bh(&sk->sk_callback_lock)
(C)
spin_lock_bh(&sk->sk_slock)
...
write_lock_bh(&sk->sk_callback_lock)
stuff
write_unlock_bh(&sk->sk_callback_lock)
spin_unlock_bh(&sk->sk_slock)
This (C) case conflicts with (A) :
CPU1 [A] CPU2 [C]
read_lock(callback_lock)
<BH> spin_lock_bh(slock)
<wait to spin_lock(slock)>
<wait to write_lock_bh(callback_lock)>
We have one problematic (C) use case in inet_csk_listen_stop() :
local_bh_disable();
bh_lock_sock(child); // spin_lock_bh(&sk->sk_slock)
WARN_ON(sock_owned_by_user(child));
...
sock_orphan(child); // write_lock_bh(&sk->sk_callback_lock)
lockdep is not happy with this, as reported by Tetsuo Handa
It seems only way to deal with this is to use read_lock_bh(callbacklock)
everywhere.
Thanks to Jarek for pointing a bug in my first attempt and suggesting
this solution.
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jarek Poplawski <jarkao2@gmail.com>
Tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change "return (EXPR);" to "return EXPR;"
return is not a function, parentheses are not required.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net/core/ethtool.c: In function 'ethtool_get_regs':
net/core/ethtool.c:818:2: error: implicit declaration of function 'vmalloc'
net/core/ethtool.c:818:9: warning: assignment makes pointer from integer without a cast
net/core/ethtool.c:833:2: error: implicit declaration of function 'vfree'
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some NICs have huge register files which exceed the maximum heap
allocation size.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge reason: Pick up the latest fixes in -rc5.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
The ethtool utility does not set masks for flow parameters that are
not specified, so if both value and mask are 0 then this must be
treated as equivalent to a mask with all bits set. Currently that is
done in the only driver that implements RX n-tuple filtering, ixgbe.
Move it to the ethtool core.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
previously, if a vlan master device was moved from one network namespace
to another, all 802.1q and macvlan slaves were deleted.
we can use dev->reg_state to figure out whether dev_change_net_namespace
is happening, since that won't set dev->reg_state NETREG_UNREGISTERING.
so, this changes 8021q and macvlan to ignore NETDEV_UNREGISTER when
reg_state is not NETREG_UNREGISTERING.
Signed-off-by: David Lamparter <equinox@diac24.net>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Daniel Lezcano <daniel.lezcano@free.fr>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To be able to switch on GRO on a device, ethtool_set_gro() checks this
device provides a get_rx_csum() method.
Some devices dont provide this method, while they do support RX
checksumming.
This patch allows bonding to support GRO :
ethtool -K bond0 gro on
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rcu_dereference_raw() now needs to know the type of its argument.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently vlan devices don't have GRO by default as none of the Ethernet
drivers add NETIF_F_GRO to their vlan_features.
As GRO is a software feature add GRO to dev->vlan_features in
register_netdevice() and let vlan_dev_init() take care that it gets
enabled only when dev->features has NETIF_F_GRO too.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev->ip_ptr is protected by rtnl and rcu.
Yet some places dont use appropriate primitives and/or locking rules.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
struct ethtool_rawip4_spec and struct ethtool_ether_spec are neither
commented nor used by any driver, so remove them. Adjust padding in
the user-visible unions that included these structures.
Fix references to struct ethtool_rawip4_spec in
ethtool_get_rx_ntuple(), which should use struct ethtool_usrip4_spec.
struct ethtool_usrip4_spec cannot hold IPv6 host addresses and there
is no separate structure that can, so remove ETH_RX_NFC_IP6 and the
reference to it in niu.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-2.6-trace into perf/core
|
|
netdev_wait_allrefs() waits that all references to a device vanishes.
It currently uses a _very_ pessimistic 250 ms delay between each probe.
Some users reported that no more than 4 devices can be dismantled per
second, this is a pretty serious problem for some setups.
Most of the time, a refcount is about to be released by an RCU callback,
that is still in flight because rollback_registered_many() uses a
synchronize_rcu() call instead of rcu_barrier(). Problem is visible if
number of online cpus is one, because synchronize_rcu() is then a no op.
time to remove 50 ipip tunnels on a UP machine :
before patch : real 11.910s
after patch : real 1.250s
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reported-by: Octavian Purdila <opurdila@ixiacom.com>
Reported-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allocate hash tables for every online cpus, not every possible ones.
NUMA aware allocations.
Dont use a full page on arches where PAGE_SIZE > 1024*sizeof(void *)
misc:
__percpu , __read_mostly, __cpuinit annotations
flow_compare_t is just an "unsigned long"
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that est_tree_lock is acquired with BH protection, the other
call is unnecessary.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
net/mac80211/main.c
|
|
__lock_sock() and __release_sock() releases and regrabs lock but
were missing proper annotations. Add it. This removes following
warning from sparse. (Currently __lock_sock() does not emit any
warning about it but I think it is better to add also.)
net/core/sock.c:1580:17: warning: context imbalance in '__release_sock' - unexpected unlock
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
move_addr_to_kernel() and copy_from_user() requires their argument
as __user pointer but were missing proper markups. Add it.
This removes following warnings from sparse.
net/core/iovec.c:44:52: warning: incorrect type in argument 1 (different address spaces)
net/core/iovec.c:44:52: expected void [noderef] <asn:1>*uaddr
net/core/iovec.c:44:52: got void *msg_name
net/core/iovec.c:55:34: warning: incorrect type in argument 2 (different address spaces)
net/core/iovec.c:55:34: expected void const [noderef] <asn:1>*from
net/core/iovec.c:55:34: got struct iovec *msg_iov
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When there is only one rps_cpus, skb_get_rxhash() can be eliminated.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch: "gro: fix different skb headrooms" in its part:
"2) allocate a minimal skb for head of frag_list" is buggy. The copied
skb has p->data set at the ip header at the moment, and skb_gro_offset
is the length of ip + tcp headers. So, after the change the length of
mac header is skipped. Later skb_set_mac_header() sets it into the
NET_SKB_PAD area (if it's long enough) and ip header is misaligned at
NET_SKB_PAD + NET_IP_ALIGN offset. There is no reason to assume the
original skb was wrongly allocated, so let's copy it as it was.
bugzilla : https://bugzilla.kernel.org/show_bug.cgi?id=16626
fixes commit: 3d3be4333fdf6faa080947b331a6a19bce1a4f57
Reported-by: Plamen Petrov <pvp-lsts@fs.uni-ruse.bg>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Plamen Petrov <pvp-lsts@fs.uni-ruse.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a net device is implementing the select_queue callback and is part of
a bridge, frames coming from the bridge already have a tx queue associated
to the socket (introduced in commit a4ee3ce3293dc931fab19beb472a8bde1295aebe,
"net: Use sk_tx_queue_mapping for connected sockets"). The call to
sk_tx_queue_get will then return the tx queue used by the bridge instead
of calling the select_queue callback.
In case of mac80211 this broke QoS which is implemented by using the
select_queue callback. Furthermore it introduced problems with rt2x00
because frames with the same TID and RA sometimes appeared on different
tx queues which the hw cannot handle correctly.
Fix this by always calling select_queue first if it is available and only
afterwards use the socket tx queue mapping.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds tracepoint to consume_skb and add trace_kfree_skb
before __kfree_skb in skb_free_datagram_locked and net_tx_action.
Combinating with tracepoint on dev_hard_start_xmit, we can check
how long it takes to free transmitted packets. And using it, we can
calculate how many packets driver had at that time. It is useful when
a drop of transmitted packet is a problem.
sshd-6828 [000] 112689.258154: consume_skb: skbaddr=f2d99bb8
Signed-off-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Kaneshige Kenji <kaneshige.kenji@jp.fujitsu.com>
Cc: Izumo Taku <izumi.taku@jp.fujitsu.com>
Cc: Kosaki Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Scott Mcmillan <scott.a.mcmillan@intel.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
LKML-Reference: <4C724364.50903@jp.fujitsu.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
|
This patch adds tracepoint to dev_queue_xmit, dev_hard_start_xmit,
netif_rx and netif_receive_skb. These tracepoints help you to monitor
network driver's input/output.
<idle>-0 [001] 112447.902030: netif_rx: dev=eth1 skbaddr=f3ef0900 len=84
<idle>-0 [001] 112447.902039: netif_receive_skb: dev=eth1 skbaddr=f3ef0900 len=84
sshd-6828 [000] 112447.903257: net_dev_queue: dev=eth4 skbaddr=f3fca538 len=226
sshd-6828 [000] 112447.903260: net_dev_xmit: dev=eth4 skbaddr=f3fca538 len=226 rc=0
Signed-off-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Kaneshige Kenji <kaneshige.kenji@jp.fujitsu.com>
Cc: Izumo Taku <izumi.taku@jp.fujitsu.com>
Cc: Kosaki Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Scott Mcmillan <scott.a.mcmillan@intel.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
LKML-Reference: <4C72431E.3000901@jp.fujitsu.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
|
|
No need to test twice sk->sk_shutdown & RCV_SHUTDOWN
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
pskb_expand_head() blindly takes references on fragments before calling
skb_release_data(), potentially releasing these references.
We can add a fast path, avoiding these atomic operations, if we own the
last reference on skb->head.
Based on a previous patch from David
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__alloc_skb() uses a memset() to clear all the beginning of skb,
including bitfields contained in 'flags1' & 'flags2'.
We dont need any more to use kmemcheck_annotate_bitfield() on these
fields. However, we still need it for the clone part, which is not
cleared.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a lockdep warning:
[ 516.287584] =========================================================
[ 516.288386] [ INFO: possible irq lock inversion dependency detected ]
[ 516.288386] 2.6.35b #7
[ 516.288386] ---------------------------------------------------------
[ 516.288386] swapper/0 just changed the state of lock:
[ 516.288386] (&qdisc_tx_lock){+.-...}, at: [<c12eacda>] est_timer+0x62/0x1b4
[ 516.288386] but this lock took another, SOFTIRQ-unsafe lock in the past:
[ 516.288386] (est_tree_lock){+.+...}
[ 516.288386]
[ 516.288386] and interrupts could create inverse lock ordering between them.
...
So, est_tree_lock needs BH protection because it's taken by
qdisc_tx_lock, which is used both in BH and process contexts.
(Full warning with this patch at netdev, 02 Sep 2010.)
Fixes commit: ae638c47dc040b8def16d05dc6acdd527628f231
("pkt_sched: gen_estimator: add a new lock")
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a small helper ptype_head() to get the head to manipulate
dev_add_pack() & __dev_remove_pack() can use a spinlock without
blocking BH, since softirq use RCU, and these functions are run from
process context only.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Packets entering GRO might have different headrooms, even for a given
flow (because of implementation details in drivers, like copybreak).
We cant force drivers to deliver packets with a fixed headroom.
1) fix skb_segment()
skb_segment() makes the false assumption headrooms of fragments are same
than the head. When CHECKSUM_PARTIAL is used, this can give csum_start
errors, and crash later in skb_copy_and_csum_dev()
2) allocate a minimal skb for head of frag_list
skb_gro_receive() uses netdev_alloc_skb(headroom + skb_gro_offset(p)) to
allocate a fresh skb. This adds NET_SKB_PAD to a padding already
provided by netdevice, depending on various things, like copybreak.
Use alloc_skb() to allocate an exact padding, to reduce cache line
needs:
NET_SKB_PAD + NET_IP_ALIGN
bugzilla : https://bugzilla.kernel.org/show_bug.cgi?id=16626
Many thanks to Plamen Petrov, testing many debugging patches !
With help of Jarek Poplawski.
Reported-by: Plamen Petrov <pvp-lsts@fs.uni-ruse.bg>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
(skb->data - skb->head) can be changed by skb_headroom(skb)
Remove some uses of NET_SKBUFF_DATA_USES_OFFSET, using
(skb_end_pointer(skb) - skb->head) or
(skb_tail_pointer(skb) - skb->head) : compiler does the right thing,
and this is more readable for us ;)
(struct skb_shared_info *) casts in pskb_expand_head() to help memcpy()
to use aligned moves.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- napi_gro_flush() is exported from net/core/dev.c, to avoid
an irq_save/irq_restore in the packet receive path.
- use napi_gro_receive() instead of netif_receive_skb()
- use napi_gro_flush() before calling __napi_complete()
- turn on NETIF_F_GRO by default
- Tested on a Marvell 88E8001 Gigabit NIC
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
remove non used variable "queue" in pg_cleanup
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
compare_ether_header() can have a special implementation on 64 bit
arches if CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is defined.
__napi_gro_receive() and vlan_gro_common() can avoid a conditional
branch to perform device match.
On x86_64, __napi_gro_receive() has now 38 instructions instead of 53
As gcc-4.4.3 still choose to not inline it, add inline keyword to this
performance critical function.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
