| Age | Commit message (Collapse) | Author |
|---|
|
While there may be a case for a driver adding its
own bits of radiotap information, none currently
does. Also, drivers would have to copy the code
to generate the radiotap bits that now mac80211
generates. If some driver in the future needs to
add some driver-specific information I'd expect
that to be in a radiotap vendor namespace and we
can add a different way of passing such data up
and having mac80211 include it.
Additionally, rename IEEE80211_CONF_RADIOTAP to
IEEE80211_CONF_MONITOR since it's still used by
b43(legacy) to obtain per-frame timestamps.
The purpose of this patch is to simplify the RX
code in mac80211 to make it easier to add paged
skb support.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Replace netif_tx_{start,stop,wake}_all_queues with the single-queue
equivalents (i.e. netif_{start,stop,wake}_queue). Since we are down to
a single queue, these should peform slightly better.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Instead of having to modify every non-mac80211 for device type assignment,
do this inside the netdev notifier callback of cfg80211. So all drivers
that integrate with cfg80211 will export a proper device type.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Ethernet framing is used for a lot of devices these days. Most
prominent are WiFi and WiMAX based devices. However for userspace
application it is important to classify these devices correctly and
not only see them as Ethernet devices. The daemons like HAL, DeviceKit
or even NetworkManager with udev support tries to do the classification
in userspace with a lot trickery and extra system calls. This is not
good and actually reaches its limitations. Especially since the kernel
does know the type of the Ethernet device it is pretty stupid.
To solve this problem the underlying device type needs to be set and
then the value will be exported as DEVTYPE via uevents and available
within udev.
# cat /sys/class/net/wlan0/uevent
DEVTYPE=wlan
INTERFACE=wlan0
IFINDEX=5
This is similar to subsystems like USB and SCSI that distinguish
between hosts, devices, disks, partitions etc.
The new SET_NETDEV_DEVTYPE() is a convenience helper to set the actual
device type. All device types are free form, but for convenience the
same strings as used with RFKILL are choosen.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When an interface is taken down while a scan is
pending -- i.e. a scan request was accepted but
not yet acted upon due to other work being in
progress -- we currently do not properly cancel
that scan and end up getting stuck. Fix this by
doing better checks when an interface is taken
down.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Due to the way the tasklets work in mac80211 there's
no need to ever disable them.
However, we need to clear the pending packets when
taking down the last interface because otherwise
the tx_pending_tasklet might be queued if the
driver mucks with the queues (which it shouldn't).
I've had a situation occasionally with ar9170 in
which ksoftirq was using 100% CPU time because
a disabled tasklet was scheduled, and I think that
was due to ar9170 receiving a packet while the
tasklet was disabled. That's strange and it really
should not do that for other reasons, but there's
no need to waste that much CPU time over it, it
should just warn instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Since configure_filter can sleep now, any multicast
configuration needed to be postponed to a work struct.
This, however, lead to a problem that we could queue
the work, stop the device and then afterwards invoke
configure_filter which may lead to driver hangs and is
a bug. To fix this, we can just cancel the filter work
since it's unnecessary to do after stopping the hw.
Since there are various places that call drv_stop, and
two of them do very similar things, the code for them
can be put into a shared function at the same time.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Tested-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Over time, a whole bunch of drivers have come up
with their own scheme to delay the configure_filter
operation to a workqueue. To be able to simplify
things, allow configure_filter to sleep, and add
a new prepare_multicast callback that drivers that
need the multicast address list implement. This new
callback must be atomic, but most drivers either
don't care or just calculate a hash which can be
done atomically and then uploaded to the hardware
non-atomically.
A cursory look suggests that at76c50x-usb, ar9170,
mwl8k (which is actually very broken now), rt2x00,
wl1251, wl1271 and zd1211 should make use of this
new capability.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When an interface is configured in the AP mode, the mac80211
implementation doesn't inform the driver to receive PS Poll frames.
It leads to inability to communicate with power-saving stations
reliably.
The FIF_CONTROL flag isn't passed by mac80211 to
ieee80211_ops.configure_filter when an interface is in the AP mode.
And it's ok, because we don't want to receive ACK frames and other
control ones, but only PS Poll ones.
This patch introduces the FIF_PSPOLL filter flag in addition to
FIF_CONTROL, which means for the driver "pass PS Poll frames".
This flag is passed to the driver:
A) When an interface is configured in the AP mode.
B) In all cases, when the FIF_CONTROL flag was passed earlier (in
addition to it).
Signed-off-by: Igor Perminov <igor.perminov@inbox.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The mac80211 workqueue exists to enable mac80211 and drivers
to queue their own work on a single threaded workqueue. mac80211
takes care to flush the workqueue during suspend but we never
really had requirements on drivers for how they should use
the workqueue in consideration for suspend.
We extend mac80211 to document how the mac80211 workqueue should
be used, how it should not be used and finally move raw access to
the workqueue to mac80211 only. Drivers and mac80211 use helpers
to queue work onto the mac80211 workqueue:
* ieee80211_queue_work()
* ieee80211_queue_delayed_work()
These helpers will now warn if mac80211 already completed its
suspend cycle and someone is trying to queue work. mac80211
flushes the mac80211 workqueue prior to suspend a few times,
but we haven't taken the care to ensure drivers won't add more
work after suspend. To help with this we add a warning when
someone tries to add work and mac80211 already completed the
suspend cycle.
Drivers should ensure they cancel any work or delayed work
in the mac80211 stop() callback.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
sparse complains about a shadowed variable, which
we can just rename, and lots of stuff if the API
tracer is enabled, so kick out the tracer code in
a sparse run -- the macros just confuse it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When downing interfaces, it's a good idea to tell the driver to
stop sending beacons; that way the driver doesn't need special
code in ops->remove_interface() when it should already handle the
case in bss_info_changed().
This fixes a potential crash with at least ath5k since the vif
pointer will be nullified while beacon interrupts are still active.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Finally! This is what you've all been waiting for!
This patch makes cfg80211 take care of wext emulation
_completely_ by itself, drivers that don't need things
cfg80211 doesn't do yet don't even need to be aware of
wireless extensions.
This means we can also clean up mac80211's and iwm's
Kconfig and make it possible to build them w/o wext
now!
RIP wext.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Use a bitfield to store the current scan mode instead of two boolean
variables {sw,hw}_scanning. This patch does not introduce functional
changes but allows us to enhance the scan flags later (for example
for background scanning).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This finally opens up the ability to put mac80211 devices
into different network namespaces. As long as you don't
have sysfs, that is.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There are still two places in mac80211 that hardcode
the initial net namespace (init_net). One of them is
mandated by cfg80211 and will be removed by a separate
patch, the other one is used for finding the network
device of a pending packet via its ifindex.
Remove the latter use by keeping track of the device
pointer itself, via the vif pointer, and avoid it
going stale by dropping pending frames for a given
interface when the interface is removed.
To keep track of the vif pointer for the correct
interface, change the info->control.vif pointer's
internal use to always be the correct vif, and only
move it to the vif the driver expects (or NULL for
monitor interfaces and injected packets) right before
giving the packet to the driver.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
With the internal 'pending' queue system in place, we can simply
put packets there instead of pushing them off to the master dev,
getting rid of the master interface completely.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In "mac80211: monitor the connection" I forgot to
add code to cancel the new timers & work when the
interface is brought down, which isn't a problem
if you just bring it down, but _is_ a problem when
you destroy the interface. Correct this lapse.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Sit tight. This shakes up the world as you know
it. Let go of your spaghetti tongs, they will no
longer be required, the horrible statemachine in
net/mac80211/mlme.c is no more...
With the cfg80211 SME mac80211 now has much less
to keep track of, but, on the other hand, for FT
it needs to be able to keep track of at least one
authentication being in progress while associated.
So convert from a single state machine to having
small ones for all the different things we need to
do. For real FT it will still need work wrt. PS,
but this should be a good step.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
With mac80211 now always controlled by an external SME,
a lot of code is dead -- SSID, BSSID, channel selection
is always done externally, etc. Additionally, rename
IEEE80211_STA_TKIP_WEP_USED to IEEE80211_STA_DISABLE_11N
and clean up the code a bit.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
To be easier on drivers and users, have cfg80211 register an
rfkill structure that drivers can access. When soft-killed,
simply take down all interfaces; when hard-killed the driver
needs to notify us and we will take down the interfaces
after the fact. While rfkilled, interfaces cannot be set UP.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When a software scan starts, it first sets sw_scanning, but
leaves the scan_channel "unset" (it currently actually gets
initialised to a default). Now, when something else tries
to (re)configure the hardware in the window between these two
events (after sw_scanning = true, but before scan_channel is
set), the current code switches to the (unset!) scan_channel.
This causes trouble, especially when switching bands and
sending frames on the wrong channel.
To work around this, leave scan_channel initialised to NULL
and use it to determine whether or not a switch to a different
channel should occur (and also use the same condition to check
whether to adjust power for scan or not).
Additionally, avoid reconfiguring the hardware completely when
recalculating idle resulted in no changes, this was the problem
that originally led us to discover the race condition in the
first place, which was helpfully bisected by Pavel. This part
of the patch should not be necessary with the other fixes, but
not calling the ieee80211_hw_config function when we know it to
be unnecessary is certainly a correct thing to do.
Unfortunately, this patch cannot and does not fix the race
condition completely, but due to the way the scan code is
structured it makes the particular problem Pavel discovered
(race while changing channel at the same time as transmitting
frames) go away. To fix it completely, more work especially
with locking configuration is needed.
Bisected-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When we aren't doing anything in mac80211, we can turn off
much of the hardware, depending on the driver/hw. Not doing
anything, aka being idle, means:
* no monitor interfaces
* no AP/mesh/wds interfaces
* any station interfaces are in DISABLED state
* any IBSS interfaces aren't trying to be in a network
* we aren't trying to scan
By creating a new function that verifies these conditions and calling
it at strategic points where the states of those conditions change,
we can easily make mac80211 tell the driver when we are idle to save
power.
Additionally, this fixes a small quirk where a recalculated powersave
state is passed to the driver even if the hardware is about to stopped
completely.
This patch intentionally doesn't touch radio_enabled because that is
currently implemented to be a soft rfkill which is inappropriate here
when we need to be able to wake up with low latency.
One thing I'm not entirely sure about is this:
phy0: device no longer idle - in use
wlan0: direct probe to AP 00:11:24:91:07:4d try 1
wlan0 direct probe responded
wlan0: authenticate with AP 00:11:24:91:07:4d
wlan0: authenticated
> phy0: device now idle
> phy0: device no longer idle - in use
wlan0: associate with AP 00:11:24:91:07:4d
wlan0: RX AssocResp from 00:11:24:91:07:4d (capab=0x401 status=0 aid=1)
wlan0: associated
Is it appropriate to go into idle state for a short time when we have
just authenticated, but not associated yet? This happens only with the
userspace SME, because we cannot really know how long it will wait
before asking us to associate. Would going idle after a short timeout
be more appropriate? We may need to revisit this, depending on what
happens.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In order to later add tracing or verifications to the driver
calls mac80211 makes, this patch adds static inline wrappers
for all operations.
All calls are now written as
drv_<op>(local, ...);
instead of
local->ops-><op>(&local->hw, ...);
Where necessary, the wrappers also do existence checking and
return default values as appropriate.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This converts mac80211 to the new cfg80211 IBSS API, the
wext handling functions are called where appropriate.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When an application asks for a latency lower than the beacon interval
there's nothing we can do -- we need to stay awake and not have the
AP buffer frames for us. Add code to automatically calculate this
constraint in mac80211 so drivers need not concern themselves with it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When you have multiple virtual interfaces the current
implementation requires setting them up properly from
userspace, which is undesirable when we want to default
to power save mode. Keep track of powersave requested
from userspace per managed mode interface, and only
enable powersave globally when exactly one managed mode
interface is active and has powersave turned on.
Second, only start the dynPS timer when PS is turned
on, and properly turn it off when PS is turned off.
Third, fix the scan_sdata abuse in the dynps code.
Finally, also reorder the code and refactor the code
that enables PS or the dynps timer instead of having
it copied in two places.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add IEEE80211_HW_BEACON_FILTERING flag so that driver inform that it supports
beacon filtering. Drivers need to call the new function
ieee80211_beacon_loss() to notify about beacon loss.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Neither can currently be set from userspace, so there's no
regression potential, and neither will be supported from
userspace since the new userspace APIs allow the SME, which
is in userspace, to control all we need.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The functionality that NL80211_CMD_SET_MGMT_EXTRA_IE provided can now
be achieved with cleaner design by adding IE(s) into
NL80211_CMD_TRIGGER_SCAN, NL80211_CMD_AUTHENTICATE,
NL80211_CMD_ASSOCIATE, NL80211_CMD_DEAUTHENTICATE, and
NL80211_CMD_DISASSOCIATE.
Since this is a very recently added command and there are no known (or
known planned) applications using NL80211_CMD_SET_MGMT_EXTRA_IE and
taken into account how much extra complexity it adds to the IE
processing we have now (and need to add in the future to fix IE order
in couple of frames), it looks like the best option is to just remove
the implementation of this command for now. The enum values themselves
are left to avoid changing the nl80211 command or attribute numbers.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This file was forgotten from the quilt patch that added MLME
primitives, so the kfree on interface removal is missing. Fix this
potential memleak by freeing the temporary Authentication frame IEs
from SME when the interface is being removed.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Even after commit "mac80211: deauth when interface is marked down"
(e327b847 on Linus tree), userspace still isn't notified when interface
goes down. There isn't a problem with this commit, but because of other
code changes it doesn't work on kernels >= 2.6.28 (works if same/similar
change applied on 2.6.27 for example).
The issue is as follows: after commit "mac80211: restructure disassoc/deauth
flows" in 2.6.28, the call to ieee80211_sta_deauthenticate added by
commit e327b847 will not work: because we do sta_info_flush(local, sdata)
inside ieee80211_stop (iface.c), all stations in interface are cleared, so
when calling ieee80211_sta_deauthenticate->ieee80211_set_disassoc (mlme.c),
inside ieee80211_set_disassoc we have this in the beginning:
sta = sta_info_get(local, ifsta->bssid);
if (!sta) {
The !sta check triggers, thus the function returns early and
ieee80211_sta_send_apinfo(sdata, ifsta) later isn't called, so
wpa_supplicant/userspace isn't notified with SIOCGIWAP.
This commit moves deauthentication to before flushing STA info
(sta_info_flush), thus the above can't happen and userspace is really
notified when interface goes down.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch splits out the ibss code and data from managed (station) mode.
The reason to do this is to better separate the state machines, and have
the code be contained better so it gets easier to determine what exactly
a given change will affect, that in turn makes it easier to understand.
This is quite some churn, especially because I split sdata->u.sta into
sdata->u.mgd and sdata->u.ibss, but I think it's easier to maintain that
way. I've also shuffled around some code -- null function sending is only
applicable to managed interfaces so put that into that file, some other
functions are needed from various places so put them into util, and also
rearranged the prototypes in ieee80211_i.h accordingly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
mac80211 currently assumes init_net for all interfaces,
so really will not cope well with network namespaces,
at least at this time.
To change this, we would have keep track of the netns
in addition to the ifindex, which is not something I
want to think about right now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds basic scan capability to cfg80211/nl80211 and
changes mac80211 to use it. The BSS list that cfg80211 maintains
is made driver-accessible with a private area in each BSS struct,
but mac80211 doesn't yet use it. That's another large project.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The sta_info pointer can very well be passed to
ieee80211_sta_tear_down_BA_sessions, this will
later allow us to pass it through even further.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Convert to new net_device_ops in 2.6.28 and later.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Using only the RTNL has a number of problems, most notably that
ieee80211_iterate_active_interfaces() and other interface list
traversals cannot be done from the internal workqueue because it
needs to be flushed under the RTNL.
This patch introduces a new mutex that protects the interface list
against modifications. A more detailed explanation is part of the
code change.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
A new nl80211 command, NL80211_CMD_SET_MGMT_EXTRA_IE, can be used to
add arbitrary IE data into the end of management frames. The interface
allows extra IEs to be configured for each management frame subtype, but
only some of them (ProbeReq, ProbeResp, Auth, (Re)AssocReq, Deauth,
Disassoc) are currently accepted in mac80211 implementation.
This makes it easier to implement IEEE 802.11 extensions like WPS and
FT that add IE(s) into some management frames. In addition, this can
be useful for testing and experimentation purposes.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Move to the advertised channel on reception of
a CSA element. This is needed for 802.11h compliance.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Since the station info is flushed before calling set_disassoc
in ieee80211_stop, the power save timer is never cancelled
when the driver is unloaded. Hence the timer cancellation has
to be done in ieee80211_stop itself.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
As TKIP is not updated to new security needs which arise when
TKIP is used to encrypt A-MPDU aggregated data frames, IEEE802.11n
does not allow any cipher other than CCMP (Which has new extensions
defined) as pairwise cipher between HT peers.
When such configuration (TKIP/WEP in HT) is forced, we still
associate in non-HT mode (11a/b/g).
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Changing mode on an interface is not allowed if IBSS is disabled for the
current channel. That restriction should only apply when switching to
the ad-hoc mode, as it was prior to "cfg80211: handle SIOCGIWMODE/SIOCSIWMODE".
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
further reducing wext code in mac80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
It seems like proper etiquette to let other stations know when we are
going down in either STA or IBSS mode. This also notifies userland, so
wpa_supplicant doesn't get confused.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Mesh interfaces are currently opened with the FIF_ALLMULTI rx filter flag set,
however there is no BSSID in mesh so BSSID filtering should be disabled by
setting the FIF_OTHER_BSS flag as well. Also explicitly call
ieee80211_configure_filter for mesh.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozbit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Move bss_conf into the vif struct so that drivers can
access it during ->tx without having to store it in
the private data or similar. No driver updates because
this is only for when they want to start using it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This makes mac80211 notify the driver which configuration
actually changed, e.g. channel etc.
No driver changes, this is just plumbing, driver authors are
expected to act on this if they want to.
Also remove the HW CONFIG debug printk, it's incorrect, often
we configure something else.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In "mac80211: make master iface not wireless" I accidentally
forgot to include these changes ... leading to the expected
BUG_ON errors.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
