| Age | Commit message (Collapse) | Author |
|---|
|
When the buffer size is set to zero in the block ack parameter set
field, we should use the maximum supported number of subframes. The
existing code was bogus and was doing some unnecessary calculations
that lead to wrong values.
Thanks Johannes for helping me figure this one out.
Cc: stable@kernel.org
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Since the introduction of the fixes for the
reorder timer, mac80211 will cause lockdep
warnings because lockdep confuses
local->skb_queue and local->rx_skb_queue
and treats their lock as the same.
However, their locks are different, and are
valid in different contexts (the former is
used in IRQ context, the latter in BH only)
and the only thing to be done is mark the
former as a different lock class so that
lockdep can tell the difference.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Sujith <m.sujith@gmail.com>
Reported-by: Miles Lane <miles.lane@gmail.com>
Tested-by: Sujith <m.sujith@gmail.com>
Tested-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In order to compute the features for other offloads (primarily
scatter/gather), we need to first check the ability of the NIC to
offload the checksum for the packet. Since we have already computed
this, we can directly use the result instead of figuring it out
again.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This switches skb_need_linearize() to use the features that have
been centrally computed. In doing so, this fixes a problem where
scatter/gather should not be used because the card does not support
checksum offloading on that type of packet. On device registration
we only check that some form of checksum offloading is available if
scatter/gatther is enabled but we must also check at transmission
time. Examples of this include IPv6 or vlan packets on a NIC that
only supports IPv4 offloading.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This switches dev_gso_segment() to use the device features computed
by the centralized routine. In doing so, it fixes a problem where
it would always use dev->features, instead of those appropriate
to the number of vlan tags if any are present.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that there is a single function that can compute the device
features relevant to a packet, we don't want to run it for each
offload. This converts netif_needs_gso() to take the features
of the device, rather than computing them itself.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netif_get_vlan_features() is currently only used by netif_needs_gso(),
so it only concerns itself with GSO features. However, several other
places also should take into account the contents of the packet when
deciding whether to offload to hardware. This generalizes the function
to return features about all of the various forms of offloading. Since
offloads tend to be linked together, this avoids duplicating the logic
in each location (i.e. the scatter/gather code also needs the checksum
logic).
Suggested-by: Michał Mirosław <mirqus@gmail.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We currently only have software fallback for one type of checksum: the
TCP/UDP one's complement. This means that a protocol that uses hardware
offloading for a different type of checksum (FCoE, SCTP) must directly
check the device's features and do the right thing ahead of time. By
the time we get to dev_can_checksum(), we're only deciding whether to
apply the one algorithm in software or hardware. NETIF_F_HW_CSUM has the
same capabilities as the software version, so we should always use it if
present. The primary advantage of this is multiply tagged vlans can use
hardware checksumming.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix new kernel-doc notation warning in net/core/filter.c:
Warning(net/core/filter.c:172): No description found for parameter 'fentry'
Warning(net/core/filter.c:172): Excess function parameter 'filter' description in 'sk_run_filter'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to NLM_F_DUMP is composed of two bits, NLM_F_ROOT | NLM_F_MATCH,
when doing "if (x & NLM_F_DUMP)", it tests for _either_ of the bits
being set. Because NLM_F_MATCH's value overlaps with NLM_F_EXCL,
non-dump requests with NLM_F_EXCL set are mistaken as dump requests.
Substitute the condition to test for _all_ bits being set.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
usb: don't use flush_scheduled_work()
speedtch: don't abuse struct delayed_work
media/video: don't use flush_scheduled_work()
media/video: explicitly flush request_module work
ioc4: use static work_struct for ioc4_load_modules()
init: don't call flush_scheduled_work() from do_initcalls()
s390: don't use flush_scheduled_work()
rtc: don't use flush_scheduled_work()
mmc: update workqueue usages
mfd: update workqueue usages
dvb: don't use flush_scheduled_work()
leds-wm8350: don't use flush_scheduled_work()
mISDN: don't use flush_scheduled_work()
macintosh/ams: don't use flush_scheduled_work()
vmwgfx: don't use flush_scheduled_work()
tpm: don't use flush_scheduled_work()
sonypi: don't use flush_scheduled_work()
hvsi: don't use flush_scheduled_work()
xen: don't use flush_scheduled_work()
gdrom: don't use flush_scheduled_work()
...
Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.
|
|
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: (65 commits)
[S390] prevent unneccesary loops_per_jiffy recalculation
[S390] cpuinfo: use get_online_cpus() instead of preempt_disable()
[S390] smp: remove cpu hotplug messages
[S390] mutex: enable spinning mutex on s390
[S390] mutex: Introduce arch_mutex_cpu_relax()
[S390] cio: fix ccwgroup unregistration race condition
[S390] perf: add DWARF register lookup for s390
[S390] cleanup ftrace backend functions
[S390] ptrace cleanup
[S390] smp/idle: call init_idle() before starting a new cpu
[S390] smp: delay idle task creation
[S390] dasd: Correct retry counter for terminated I/O.
[S390] dasd: Add support for raw ECKD access.
[S390] dasd: Prevent deadlock during suspend/resume.
[S390] dasd: Improve handling of stolen DASD reservation
[S390] dasd: do path verification for paths added at runtime
[S390] dasd: add High Performance FICON multitrack support
[S390] cio: reduce memory consumption of itcw structures
[S390] nmi: enable machine checks early
[S390] qeth: buffer count imbalance
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/npiggin/linux-npiggin
* 'vfs-scale-working' of git://git.kernel.org/pub/scm/linux/kernel/git/npiggin/linux-npiggin: (57 commits)
fs: scale mntget/mntput
fs: rename vfsmount counter helpers
fs: implement faster dentry memcmp
fs: prefetch inode data in dcache lookup
fs: improve scalability of pseudo filesystems
fs: dcache per-inode inode alias locking
fs: dcache per-bucket dcache hash locking
bit_spinlock: add required includes
kernel: add bl_list
xfs: provide simple rcu-walk ACL implementation
btrfs: provide simple rcu-walk ACL implementation
ext2,3,4: provide simple rcu-walk ACL implementation
fs: provide simple rcu-walk generic_check_acl implementation
fs: provide rcu-walk aware permission i_ops
fs: rcu-walk aware d_revalidate method
fs: cache optimise dentry and inode for rcu-walk
fs: dcache reduce branches in lookup path
fs: dcache remove d_mounted
fs: fs_struct use seqlock
fs: rcu-walk for path lookup
...
|
|
The 'seq_window' sysctl sets the initial value for the DCCP Sequence Window,
which may range from 32..2^46-1 (RFC 4340, 7.5.2). The patch sets the upper
bound consistently to 2^32-1 on both 32 and 64 bit systems, which should be
sufficient - with a RTT of 1sec and 1-byte packets, a seq_window of 2^32-1
corresponds to a link speed of 34 Gbps.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
|
|
Currently dccp_check_seqno allows any valid packet to update the Greatest
Sequence Number Received, even if that packet's sequence number is less than
the current GSR. This patch adds a check to make sure that the new packet's
sequence number is greater than GSR.
Signed-off-by: Samuel Jero <sj323707@ohio.edu>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
|
|
Currently dccp_check_seqno returns 0 (indicating a valid packet) if the
acknowledgment number is out of bounds and the sync that RFC 4340 mandates at
this point is currently being rate-limited. This function should return -1,
indicating an invalid packet.
Signed-off-by: Samuel Jero <sj323707@ohio.edu>
Acked-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
|
|
The problem that this patch aims to fix is vfsmount refcounting scalability.
We need to take a reference on the vfsmount for every successful path lookup,
which often go to the same mount point.
The fundamental difficulty is that a "simple" reference count can never be made
scalable, because any time a reference is dropped, we must check whether that
was the last reference. To do that requires communication with all other CPUs
that may have taken a reference count.
We can make refcounts more scalable in a couple of ways, involving keeping
distributed counters, and checking for the global-zero condition less
frequently.
- check the global sum once every interval (this will delay zero detection
for some interval, so it's probably a showstopper for vfsmounts).
- keep a local count and only taking the global sum when local reaches 0 (this
is difficult for vfsmounts, because we can't hold preempt off for the life of
a reference, so a counter would need to be per-thread or tied strongly to a
particular CPU which requires more locking).
- keep a local difference of increments and decrements, which allows us to sum
the total difference and hence find the refcount when summing all CPUs. Then,
keep a single integer "long" refcount for slow and long lasting references,
and only take the global sum of local counters when the long refcount is 0.
This last scheme is what I implemented here. Attached mounts and process root
and working directory references are "long" references, and everything else is
a short reference.
This allows scalable vfsmount references during path walking over mounted
subtrees and unattached (lazy umounted) mounts with processes still running
in them.
This results in one fewer atomic op in the fastpath: mntget is now just a
per-CPU inc, rather than an atomic inc; and mntput just requires a spinlock
and non-atomic decrement in the common case. However code is otherwise bigger
and heavier, so single threaded performance is basically a wash.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
|
|
Regardless of how much we possibly try to scale dcache, there is likely
always going to be some fundamental contention when adding or removing children
under the same parent. Pseudo filesystems do not seem need to have connected
dentries because by definition they are disconnected.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
|
|
Reduce some branches and memory accesses in dcache lookup by adding dentry
flags to indicate common d_ops are set, rather than having to check them.
This saves a pointer memory access (dentry->d_op) in common path lookup
situations, and saves another pointer load and branch in cases where we
have d_op but not the particular operation.
Patched with:
git grep -E '[.>]([[:space:]])*d_op([[:space:]])*=' | xargs sed -e 's/\([^\t ]*\)->d_op = \(.*\);/d_set_d_op(\1, \2);/' -e 's/\([^\t ]*\)\.d_op = \(.*\);/d_set_d_op(\&\1, \2);/' -i
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
|
|
Pseudo filesystems that don't put inode on RCU list or reachable by
rcu-walk dentries do not need to RCU free their inodes.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
|
|
RCU free the struct inode. This will allow:
- Subsequent store-free path walking patch. The inode must be consulted for
permissions when walking, so an RCU inode reference is a must.
- sb_inode_list_lock to be moved inside i_lock because sb list walkers who want
to take i_lock no longer need to take sb_inode_list_lock to walk the list in
the first place. This will simplify and optimize locking.
- Could remove some nested trylock loops in dcache code
- Could potentially simplify things a bit in VM land. Do not need to take the
page lock to follow page->mapping.
The downsides of this is the performance cost of using RCU. In a simple
creat/unlink microbenchmark, performance drops by about 10% due to inability to
reuse cache-hot slab objects. As iterations increase and RCU freeing starts
kicking over, this increases to about 20%.
In cases where inode lifetimes are longer (ie. many inodes may be allocated
during the average life span of a single inode), a lot of this cache reuse is
not applicable, so the regression caused by this patch is smaller.
The cache-hot regression could largely be avoided by using SLAB_DESTROY_BY_RCU,
however this adds some complexity to list walking and store-free path walking,
so I prefer to implement this at a later date, if it is shown to be a win in
real situations. I haven't found a regression in any non-micro benchmark so I
doubt it will be a problem.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
|
|
Change d_delete from a dentry deletion notification to a dentry caching
advise, more like ->drop_inode. Require it to be constant and idempotent,
and not take d_lock. This is how all existing filesystems use the callback
anyway.
This makes fine grained dentry locking of dput and dentry lru scanning
much simpler.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
|
|
Since nf_bridge_maybe_copy_header() may change the length of skb,
we should check the length of skb after it to handle the ppoe skbs.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In 1ae4de0cdf855305765592647025bde55e85e451, the secctx was exported
via the /proc/net/netfilter/nf_conntrack and ctnetlink interfaces
instead of the secmark.
That patch introduced the use of security_secid_to_secctx() which may
return a non-zero value on error.
In one of my setups, I have NF_CONNTRACK_SECMARK enabled but no
security modules. Thus, security_secid_to_secctx() returns a negative
value that results in the breakage of the /proc and `conntrack -L'
outputs. To fix this, we skip the inclusion of secctx if the
aforementioned function fails.
This patch also fixes the dynamic netlink message size calculation
if security_secid_to_secctx() returns an error, since its logic is
also wrong.
This problem exists in Linux kernel >= 2.6.37.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since nf_ct_expect_dst_hash() may be called without nf_conntrack_lock
locked, nf_ct_expect_hash_rnd should be initialized in the atomic way.
In this patch, we use nf_conntrack_hash_rnd instead of
nf_ct_expect_hash_rnd.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RFC3168 (The Addition of Explicit Congestion Notification to IP)
states :
5.3. Fragmentation
ECN-capable packets MAY have the DF (Don't Fragment) bit set.
Reassembly of a fragmented packet MUST NOT lose indications of
congestion. In other words, if any fragment of an IP packet to be
reassembled has the CE codepoint set, then one of two actions MUST be
taken:
* Set the CE codepoint on the reassembled packet. However, this
MUST NOT occur if any of the other fragments contributing to
this reassembly carries the Not-ECT codepoint.
* The packet is dropped, instead of being reassembled, for any
other reason.
This patch implements this requirement for IPv4, choosing the first
action :
If one fragment had NO-ECT codepoint
reassembled frame has NO-ECT
ElIf one fragment had CE codepoint
reassembled frame has CE
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The original code has a use after free bug because it's not using the
_safe() version of the list_for_each_entry() macro.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a "goto nla_put_failure" hidden inside the NLA_PUT() macro, but
we're holding the dcb_lock so we need to unlock first.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
|
|
Leonardo Chiquitto found poll() could block forever on tcp sockets and
Urgent data was received, if the event flag only contains POLLPRI.
He did a bisection and found commit 4938d7e0233 (poll: avoid extra
wakeups in select/poll) was the source of the problem.
Problem is TCP sockets use standard sock_def_readable() function for
their sk_data_ready() handler, and sock_def_readable() doesnt signal
POLLPRI.
Only TCP is affected by the problem. Adding POLLPRI to the list of flags
might trigger unnecessary schedules, but URGENT handling is such a
seldom used feature this seems a good compromise.
Thanks a lot to Leonardo for providing the bisection result and a test
program as well.
Reference : http://www.spinics.net/lists/netdev/msg151793.html
Reported-and-bisected-by: Leonardo Chiquitto <leonardo.lists@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
unix_release() can asynchornously set socket->sk to NULL, and
it does so without holding the unix_state_lock() on "other"
during stream connects.
However, the reverse mapping, sk->sk_socket, is only transitioned
to NULL under the unix_state_lock().
Therefore make the security hooks follow the reverse mapping instead
of the forward mapping.
Reported-by: Jeremy Fitzhardinge <jeremy@goop.org>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 57dbb2d83d100ea (sched: add head drop fifo queue)
introduced pfifo_head_drop, and broke the invariant that
sch->bstats.bytes and sch->bstats.packets are COUNTER (increasing
counters only)
This can break estimators because est_timer() handles unsigned deltas
only. A decreasing counter can then give a huge unsigned delta.
My mid term suggestion would be to change things so that
sch->bstats.bytes and sch->bstats.packets are incremented in dequeue()
only, not at enqueue() time. We also could add drop_bytes/drop_packets
and provide estimations of drop rates.
It would be more sensible anyway for very low speeds, and big bursts.
Right now, if we drop packets, they still are accounted in byte/packets
abolute counters and rate estimators.
Before this mid term change, this patch makes pfifo_head_drop behavior
similar to other qdiscs in case of drops :
Dont decrement sch->bstats.bytes and sch->bstats.packets
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Somehow this snuck into my earlier patch, and
only now did I see a compiler warning:
net/mac80211/led.c:218:13: warning: function '__ieee80211_create_tpt_led_trigger' with external linkage has definition
Remove the stray extern.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When the driver has remain-on-channel offload,
implement off-channel transmission using that
primitive.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This allows drivers to support remain-on-channel
offload if they implement smarter timing or need
to use a device implementation like iwlwifi.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem
Conflicts:
net/bluetooth/Makefile
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
Up to now /proc/interrupts only has statistics for external and i/o
interrupts but doesn't split up them any further.
This patch adds a line for every single interrupt source so that it
is possible to easier tell what the machine is/was doing.
Part of the output now looks like this;
CPU0 CPU2 CPU4
EXT: 3898 4232 2305
I/O: 782 315 245
CLK: 1029 1964 727 [EXT] Clock Comparator
IPI: 2868 2267 1577 [EXT] Signal Processor
TMR: 0 0 0 [EXT] CPU Timer
TAL: 0 0 0 [EXT] Timing Alert
PFL: 0 0 0 [EXT] Pseudo Page Fault
[...]
NMI: 0 1 1 [NMI] Machine Checks
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
|
|
The key documentation is slightly out of date, fix
that. Also, the list entry in the key struct is no
longer used that way, so list_del_init() isn't
necessary any more there.
Finally, ieee80211_key_link() is no longer invoked
under RCU read lock, but rather with an appropriate
station lock held.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This reverts enables the reorder release timer once again.
The issues laid out in:
<http://www.spinics.net/lists/linux-wireless/msg57214.html>
Have been addressed by:
mac80211: serialize rx path workers
mac80211: ignore PSM bit of reordered frames
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch addresses the issue of serialization between
the main rx path and various reorder release timers.
<http://www.spinics.net/lists/linux-wireless/msg57214.html>
It converts the previously local "frames" queue into
a global rx queue [rx_skb_queue]. This way, everyone
(be it the main rx-path or some reorder release timeout)
can add frames to it.
Only one active rx handler worker [ieee80211_rx_handlers]
is needed. All other threads which have lost the race of
"runnning_rx_handler" can now simply "return", knowing that
the thread who had the "edge" will also take care of their
workload.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fixes the misplaced article in the following:
"cfg80211: Updating information on frequency 5785 MHz for
20 a MHz width channel with regulatory rule:"
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fixed a bug where if a mesh interface has a different MAC address from its bridge
interface, then it would not be able to send data traffic to any other mesh node.
This also adds support for communication between mesh nodes and external bridged
nodes by using a 6 address format if the source is a node within the mesh and the
destination is an external node proxied by a mesh portal.
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch tackles one of the problems of my
reorder release timer patch from August.
<http://www.spinics.net/lists/linux-wireless/msg57214.html>
=>
What if the reorder release triggers and ap_sta_ps_end
(called by ieee80211_rx_h_sta_process) accidentally clears
the WLAN_STA_PS_STA flag, because 100ms ago - when the STA
was still active - frames were put into the reorder buffer.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The preferred source address is currently ignored for local routes,
which results in all local connections having a src address that is the
same as the local dst address. Fix this by respecting the preferred source
address when it is provided for local routes.
This bug can be demonstrated as follows:
# ifconfig dummy0 192.168.0.1
# ip route show table local | grep local.*dummy0
local 192.168.0.1 dev dummy0 proto kernel scope host src 192.168.0.1
# ip route change table local local 192.168.0.1 dev dummy0 \
proto kernel scope host src 127.0.0.1
# ip route show table local | grep local.*dummy0
local 192.168.0.1 dev dummy0 proto kernel scope host src 127.0.0.1
We now establish a local connection and verify the source IP
address selection:
# nc -l 192.168.0.1 3128 &
# nc 192.168.0.1 3128 &
# netstat -ant | grep 192.168.0.1:3128.*EST
tcp 0 0 192.168.0.1:3128 192.168.0.1:33228 ESTABLISHED
tcp 0 0 192.168.0.1:33228 192.168.0.1:3128 ESTABLISHED
Signed-off-by: Joel Sing <jsing@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/padovan/bluetooth-next-2.6
|
|
commit ad0e2b5a00dbec303e4682b403bb6703d11dcdb2
Author: Johannes Berg <johannes.berg@intel.com>
Date: Tue Jun 1 10:19:19 2010 +0200
mac80211: simplify key locking
removed the synchronization against RCU and thus
opened a race window where we can use a key for
TX while it is already freed. Put a synchronisation
into the right place to close that window.
Reported-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: stable@kernel.org [2.6.36+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Commit b51aff057c9d0ef6c529dc25fd9f775faf7b6c63 said:
Under memory pressure, the mac80211 mesh code
may helpfully print a message that it failed
to clone a mesh frame and then will proceed
to crash trying to use it anyway. Fix that.
Avoid the reference whenever the frame copy is unsuccessful
regardless of the debug message being suppressed or printed.
Cc: stable@kernel.org [2.6.27+]
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
