| Age | Commit message (Collapse) | Author |
|---|
|
adds a socket option for low latency polling.
This allows overriding the global sysctl value with a per-socket one.
Unexport sysctl_net_ll_poll since for now it's not needed in modules.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove NET_LL_RX_POLL from the config menu.
Change default to y.
Busy polling still needs to be enabled at run time.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use sched_clock() instead of get_cycles().
We can use sched_clock() because we don't care much about accuracy.
Remove the dependency on X86_TSC
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no reason for sysctl_net_ll_poll to be an unsigned long.
Change it into an unsigned int.
Fix the proc handler.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case we need to bail out for whatever reason during assoc
init, we call sctp_endpoint_put() and then sock_put(), however,
we've hold both refs in reverse, non-symmetric order, so first
sctp_endpoint_hold() and then sock_hold().
Reverse this, so that in an error case we have sock_put() and then
sctp_endpoint_put(). Actually shouldn't matter too much, since both
cleanup paths do the right thing, but that way, it is more consistent
with the rest of the code.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's only used at this one time, so we could remove it as well.
This is valid and also makes it more explicit/obvious that in case
of error the sp->ep is NULL here, i.e. for the sctp_destroy_sock()
check that was recently added.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While this currently cannot trigger any NULL pointer dereference in
sctp_seq_dump_local_addrs(), better change the order of commands to
prevent a future bug to happen. Although we first add SCTP_CMD_NEW_ASOC
and then set the SCTP_CMD_INIT_CHOOSE_TRANSPORT, it is okay for now,
since this primitive is only called by sctp_connect() or sctp_sendmsg()
with sctp_assoc_add_peer() set first. However, lets do this precaution
and first set the transport and then add it to the association hashlist
to prevent in future something to possibly triggering this.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This clearly states a BUG somewhere in the SCTP code as e.g. fixed once
in f28156335 ("sctp: Use correct sideffect command in duplicate cookie
handling"). If this ever happens, throw a trace in the sideeffect engine
where assocs clearly must have a primary_path assigned.
When in sctp_seq_dump_local_addrs() also throw a WARN and bail out since
we do not need to panic for printing this one asterisk. Also, it will
avoid the not so obvious case when primary != NULL test passes and at a
later point in time triggering a NULL ptr dereference caused by primary.
While at it, also fix up the white space.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jesse/openvswitch
Jesse Gross says:
====================
A few miscellaneous improvements and cleanups before the GRE tunnel
integration series. Intended for net-next/3.11.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is not functional change, this is just code cleanup.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
|
|
Following patch keeps skb->csum correct across ovs.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
|
|
Flagged with: https://github.com/lyda/misspell-check
Run with: git ls-files | misspellings -f -
Signed-off-by: Andy Hill <hillad@gmail.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
|
|
Signed-off-by: Lorand Jakab <lojakab@cisco.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
|
|
Following patch changes vport->send return type so that vport
layer can do error accounting.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
|
|
The get_config vport op is left over from old compatibility code,
it is neither used nor implemented any more.
Signed-off-by: Jesse Gross <jesse@nicira.com>
|
|
It is an error to try to change the type of a vport using the set
command. However, while we check that this is an error, we still
proceed to allocate memory which then gets freed immediately.
This stops processing after noticing the error, which does not
actually fix a bug but is more correct.
Signed-off-by: Jesse Gross <jesse@nicira.com>
|
|
Add netlink directives and ndo entry to allow for controling
VF link, which can be in one of three states:
Auto - VF link state reflects the PF link state (default)
Up - VF link state is up, traffic from VF to VF works even if
the actual PF link is down
Down - VF link state is down, no traffic from/to this VF, can be of
use while configuring the VF
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
htb_class structures are big, and source of false sharing on SMP.
By carefully splitting them in two parts, we can improve performance.
I got 9 % performance increase on a 24 threads machine, with 200
concurrent netperf in TCP_RR mode, using a HTB hierarchy of 4 classes.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Caught by sparse:
- __rcu: missing annotation to sd->flow_limit
- __user: direct access in cpumask_scnprintf
Also
- add endline character when printing bitmap if room in buffer
- avoid bucket overflow by reducing FLOW_LIMIT_HISTORY
The last item warrants some explanation. The hashtable buckets are
subject to overflow if FLOW_LIMIT_HISTORY is larger than or equal
to bucket size, since all packets may end up in a single bucket. The
current (rather arbitrary) history value of 256 happens to match the
buffer size (u8).
As a result, with a single flow, the first 128 packets are accepted
(correct), the second 128 packets dropped (correct) and then the
history[] array has filled, so that each subsequent new packet
causes an increment in the bucket for new_flow plus a decrement
for old_flow: a steady state.
This is fine if packets are dropped, as the steady state goes away
as soon as a mix of traffic reappears. But, because the 256th packet
overflowed the bucket to 0: no packets are dropped.
Instead of explicitly adding an overflow check, this patch changes
FLOW_LIMIT_HISTORY to never be able to overflow a single bucket.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
(first item)
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Linux sends new unset data during disorder and recovery state if all
(suspected) lost packets have been retransmitted ( RFC5681, section
3.2 step 1 & 2, RFC3517 section 4, NexSeg() Rule 2). One requirement
is to keep the receive window about twice the estimated sender's
congestion window (tcp_rcv_space_adjust()), assuming the fast
retransmits repair the losses in the next round trip.
But currently it's not the case on the first round trip in either
normal or Fast Open connection, beucase the initial receive window
is identical to (expected) sender's initial congestion window. The
fix is to double it.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reduce the uses of this unnecessary typedef.
Done via perl script:
$ git grep --name-only -w ctl_table net | \
xargs perl -p -i -e '\
sub trim { my ($local) = @_; $local =~ s/(^\s+|\s+$)//g; return $local; } \
s/\b(?<!struct\s)ctl_table\b(\s*\*\s*|\s+\w+)/"struct ctl_table " . trim($1)/ge'
Reflow the modified lines that now exceed 80 columns.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since team functionality relies heavily on userspace daemon, we need to
deliver event to userspace via Netlink as quick as possible. So make all
team port device link events urgent.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net/ipv4/ping.c:286:5: sparse: symbol 'ping_check_bind_addr' was not declared. Should it be static?
net/ipv4/ping.c:355:6: sparse: symbol 'ping_set_saddr' was not declared. Should it be static?
net/ipv4/ping.c:370:6: sparse: symbol 'ping_clear_saddr' was not declared. Should it be static?
net/ipv6/ping.c:60:5: sparse: symbol 'dummy_ipv6_recv_error' was not declared. Should it be static?
net/ipv6/ping.c:64:5: sparse: symbol 'dummy_ip6_datagram_recv_ctl' was not declared. Should it be static?
net/ipv6/ping.c:69:5: sparse: symbol 'dummy_icmpv6_err_convert' was not declared. Should it be static?
net/ipv6/ping.c:73:6: sparse: symbol 'dummy_ipv6_icmp_error' was not declared. Should it be static?
net/ipv6/ping.c:75:5: sparse: symbol 'dummy_ipv6_chk_addr' was not declared. Should it be static?
net/ipv6/ping.c:201:5: sparse: symbol 'ping_v6_seq_show' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Corrects an byte order conflict introduced by
158874cac61245b84e939c92c53db7000122b7b0
("sctp: Correct access to skb->{network, transport}_header").
The values in question are host byte order.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit da12c90e099789a63073fc82a19542ce54d4efb9
"netlink: Add compare function for netlink_table"
only set compare at the time we create kernel netlink,
and reset compare to NULL at the time we finially
release netlink socket, but netlink_lookup wants
the compare exist always.
So we should set compare after we allocate nl_table,
and never reset it. make comapre exist all the time.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit ba418fa357a7b3c ("soreuseport: UDP/IPv4 implementation")
added following sparse errors :
net/ipv4/udp.c:433:60: warning: cast from restricted __be16
net/ipv4/udp.c:433:60: warning: incorrect type in argument 1 (different base types)
net/ipv4/udp.c:433:60: expected unsigned short [unsigned] [usertype] val
net/ipv4/udp.c:433:60: got restricted __be16 [usertype] sport
net/ipv4/udp.c:433:60: warning: cast from restricted __be16
net/ipv4/udp.c:433:60: warning: cast from restricted __be16
net/ipv4/udp.c:514:60: warning: cast from restricted __be16
net/ipv4/udp.c:514:60: warning: incorrect type in argument 1 (different base types)
net/ipv4/udp.c:514:60: expected unsigned short [unsigned] [usertype] val
net/ipv4/udp.c:514:60: got restricted __be16 [usertype] sport
net/ipv4/udp.c:514:60: warning: cast from restricted __be16
net/ipv4/udp.c:514:60: warning: cast from restricted __be16
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix following sparse error :
net/ipv4/af_inet.c:1410:59: warning: restricted __be16 degrades to
integer
added in commit db8caf3dbc77599
("gro: should aggregate frames without DF")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
From: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next
John W. Linville says:
====================
This pull request is intended for the 3.11 stream...
One big highlight is the cw1200 driver the ST-E CW1100 & CW1200
WLAN chipsets. This one has been lingering for a while, lacking
some review comments. Once started getting pulled into linux-next,
it got a bit more attention and a number of improvements were made
over the initial cut. No doubt there will be more changes ahead,
but I think it is looking alright at this point.
Along with that, there is the usual flurry of updates to the mac80211
core and the iwlwifi, mwifiex, ath9k, rt2x00, wil6210, and other
drivers. A few of the highlights are some rt2x00 refactoring/cleanup
by Gabor Juhos, some rt2800 hardware support enhancements by Stanislaw
Gruszka, some iwlwifi power management updates from Alexander Bondar,
some enhanced bcma SPROM support from Rafał Miłecki, and a variety
of other things here and there.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix following sparse errors :
net/ipv4/igmp.c:1222:25: warning: cast from restricted __be32
net/ipv4/igmp.c:1234:31: warning: incorrect type in assignment (different address spaces)
net/ipv4/igmp.c:1234:31: expected struct ip_mc_list [noderef] <asn:4>*next_hash
net/ipv4/igmp.c:1234:31: got struct ip_mc_list *<noident>
net/ipv4/igmp.c:1250:31: warning: incorrect type in assignment (different address spaces)
net/ipv4/igmp.c:1250:31: expected struct ip_mc_list [noderef] <asn:4>*next_hash
net/ipv4/igmp.c:1250:31: got struct ip_mc_list *<noident>
net/ipv4/igmp.c:2380:37: warning: cast from restricted __be32
These were added by commit e9897071350bd9
("igmp: hash a hash table to speedup ip_check_mc_rcu()")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We currently allow for numa-node aware skb allocation only within the
fill_packet_ipv4() path, but not in fill_packet_ipv6(). Consolidate that
code to a common allocation helper to enable numa-node aware skb
allocation for ipv6, and use it in both paths. This also makes both
functions a bit more readable.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similarly to TCP offloading and UDPv6 offloading, move all related
UDPv4 functions to udp_offload.c to make things more explicit. Also,
by this, we can make those functions static.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ip_mc_init_dev() is passed a freshly kzalloc'd in_device so it is
unnecessary to explicitly zero out the members.
Signed-off-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After IP route cache removal, multicast applications using
a lot of multicast addresses hit a O(N) behavior in ip_check_mc_rcu()
Add a per in_device hash table to get faster lookup.
This hash table is created only if the number of items in mc_list is
above 4.
Reported-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With a thousand htb classes, est_timer() spends ~5 million cpu cycles
and throws out cpu cache, because each htb class has a default
rate estimator (est 4sec 16sec).
Most users do not use default rate estimators, so switch htb
to not setup ones.
Add a module parameter (htb_rate_est) so that users relying
on this default rate estimator can revert the behavior.
echo 1 >/sys/module/sch_htb/parameters/htb_rate_est
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before allowing 64bits bytes rates, refactor
psched_ratecfg_precompute() to get better comments
and increased accuracy.
rate_bps field is renamed to rate_bytes_ps, as we only
have to worry about bytes per second.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
Conflicts:
drivers/net/wireless/ath/ath9k/debug.c
net/mac80211/iface.c
|
|
struct gnet_stats_rate_est contains u32 fields, so the bytes per second
field can wrap at 34360Mbit.
Add a new gnet_stats_rate_est64 structure to get 64bit bps/pps fields,
and switch the kernel to use this structure natively.
This structure is dumped to user space as a new attribute :
TCA_STATS_RATE_EST64
Old tc command will now display the capped bps (to 34360Mbit), instead
of wrapped values, and updated tc command will display correct
information.
Old tc command output, after patch :
eric:~# tc -s -d qd sh dev lo
qdisc pfifo 8001: root refcnt 2 limit 1000p
Sent 80868245400 bytes 1978837 pkt (dropped 0, overlimits 0 requeues 0)
rate 34360Mbit 189696pps backlog 0b 0p requeues 0
This patch carefully reorganizes "struct Qdisc" layout to get optimal
performance on SMP.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 1a37e412a022(net: Use 16bits for *_headers fields of struct
skbuff), skb->*_header are relative to skb->head,
so copy_skb_header() should not call skb_headers_offset_update() now,
and we should pass correct parameter to skb_headers_offset_update() in
pskb_expand_head() and skb_copy_expand().
Signed-off-by: Weiping Pan <panweiping3@gmail.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As we know, netlink sockets are private resource of
net namespace, they can communicate with each other
only when they in the same net namespace. this works
well until we try to add namespace support for other
subsystems which use netlink.
Don't like ipv4 and route table.., it is not suited to
make these subsytems belong to net namespace, Such as
audit and crypto subsystems,they are more suitable to
user namespace.
So we must have the ability to make the netlink sockets
in same user namespace can communicate with each other.
This patch adds a new function pointer "compare" for
netlink_table, we can decide if the netlink sockets can
communicate with each other through this netlink_table
self-defined compare function.
The behavior isn't changed if we don't provide the compare
function for netlink_table.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Acked-by: Serge E. Hallyn <serge.hallyn@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a flag to control flood of unicast traffic. By default, flood is
on and the bridge will flood unicast traffic if it doesn't know
the destination. When the flag is turned off, unicast traffic
without an FDB will not be forwarded to the specified port.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow user to control whether mac learning is enabled on the port.
By default, mac learning is enabled. Disabling mac learning will
cause new dynamic FDB entries to not be created for a particular port.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to the following commits:
commit 00f97da17a0c8d656d0c9 (netpoll: fix position of network header)
commit 525cebedb32a87fa48584 (pktgen: Fix position of ip and udp header)
using skb_tail_offset() seems not correct since the offset
is based on head pointer.
With the last caller removed, skb_tail_offset() can be killed
finally.
Cc: Thomas Graf <tgraf@suug.ch>
Cc: Daniel Borkmann <dborkmann@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds low latency socket poll support for TCP.
In tcp_v[46]_rcv() add a call to sk_mark_ll() to copy the napi_id
from the skb to the sk.
In tcp_recvmsg(), when there is no data in the socket we busy-poll.
This is a good example of how to add busy-poll support to more protocols.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Tested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add upport for busy-polling on UDP sockets.
In __udp[46]_lib_rcv add a call to sk_mark_ll() to copy the napi_id
from the skb into the sk.
This is done at the earliest possible moment, right after we identify
which socket this skb is for.
In __skb_recv_datagram When there is no data and the user
tries to read we busy poll.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Tested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds an ndo_ll_poll method and the code that supports it.
This method can be used by low latency applications to busy-poll
Ethernet device queues directly from the socket code.
sysctl_net_ll_poll controls how many microseconds to poll.
Default is zero (disabled).
Individual protocol support will be added by subsequent patches.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Tested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds a napi_id and a hashing mechanism to lookup a napi by id.
This will be used by subsequent patches to implement low latency
Ethernet device polling.
Based on a code sample by Eric Dumazet.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I can hit ENOBUFS in the sendmsg() path with a large batch that is
composed of many netlink messages. Here that limit is 8 MBytes of
skbuff data area as kmalloc does not manage to get more than that.
While discussing atomic rule-set for nftables with Patrick McHardy,
we decided to put all rule-set updates that need to be applied
atomically in one single batch to simplify the existing approach.
However, as explained above, the existing netlink code limits us
to a maximum of ~20000 rules that fit in one single batch without
hitting ENOBUFS. iptables does not have such limitation as it is
using vmalloc.
This patch adds netlink_alloc_large_skb() which is only used in
the netlink_sendmsg() path. It uses alloc_skb if the memory
requested is <= one memory page, that should be the common case
for most subsystems, else vmalloc for higher memory allocations.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Would be good to make things explicit and move those functions to
a new file called tcp_offload.c, thus make this similar to tcpv6_offload.c.
While moving all related functions into tcp_offload.c, we can also
make some of them static, since they are only used there. Also, add
an explicit registration function.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have the minimal inline helper tcp_skb_mss to access
skb_shinfo(skb)->gso_size, so also use it here to get mss.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge 'net' into 'net-next' to get the MSG_CMSG_COMPAT
regression fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
