Age | Commit message (Collapse) | Author |
|
This will save ~15ms boot time.
The first 10ms sleep was introduced in commit d2595d86e5 for (buggy)
Cxt codecs, so better to limit the sleep to the problem hardware.
For the second 10ms sleep, the HDA spec says:
Power State[1:0]:
00: Node Power state (D0) is fully on.
01: Node Power state (D1) allows for (does not require) the lowest possible power consuming state from which it
can return to the "fully on" state (D0) within 10 ms, excepting analog pass through circuits (e.g., CD analog
playback) which must remain fully on.
10: Node Power state (D2) allows for (does not require) the lowest possible power consuming state from which it
can return to the "fully on" state (D0) within 10 ms. For modems, this is the "wake on ring" power state.
11: Node Power state (D3) allows for (does not require) lowest possible power consuming state under software
control. Note that any low power state set by software must retain sufficient operational capability to properly
respond to subsequent software Power State command.
So 10ms is actually the max wait time. It should be safe to
remove/reduce it and rely on the loop of 1ms-sleeps.
CC: Marc Boucher <marc@linuxant.com>
CC: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add support for Macbook Air 2,1 (late 2008) internal speaker and
headphones. Create a "mba21" model for snd-hda-intel.
Signed-off-by: Reimundo Heluani <rheluani@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch enables snoop, eliminating static during playback.
This patch supersedes the previous Cougar Point audio patch.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The channel mode definitions for macmini3 model are identical with mb5.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
Add a headphones-only quirk for the Fujitsu Siemens D1289.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-and-tested-by: Marc Haber <mh+alsa201002@zugschlus.de>
Cc: <stable@kernel.org>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
With PulseAudio and an application accessing an input device like `gnome-volume-manager` both have high CPU load as reported in [1].
Loading `snd-hda-intel` with `position_fix=1` fixes this issue. Therefore add a quirk for ASUS M2V-MX SE.
The only downside is, when now exiting for example MPlayer when it is playing an audio file a high pitched sound is outputted by the speaker.
$ lspci -vvnn | grep -A10 Audio
20:01.0 Audio device [0403]: VIA Technologies, Inc. VT1708/A [Azalia HDAC] (VIA High Definition Audio Controller) [1106:3288] (rev 10)
Subsystem: ASUSTeK Computer Inc. Device [1043:8290]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fbffc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
[1] http://sourceforge.net/mailarchive/forum.php?thread_name=1265550675.4642.24.camel%40mattotaupa&forum_name=alsa-user
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Use the standard unsol_event callback with each setup callback for
IntelMac models with Realtek ALC885 codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
BugLink: https://bugs.edge.launchpad.net/ubuntu/+source/linux/+bug/343989
Add a model quirk for the NVIDIA based Macmini hardware, aka Macmini 3,1. The
pinout is almost identical to the mb5 quirk, except for no microphone and
the line-in mixer controls being on a different index. Everything works in
2ch mode, but as I am not sure what needs to be changed for 6ch mode, or
whether the Mac Mini's chip supports 6ch mode, I have simply duplicated
the code from the mb5 quirk for the mac mini chmode management. The new
model parameter for this quirk is "macmini3".
Signed-off-by: Luke Yelavich <luke.yelavich@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
BugLink: https://bugs.launchpad.net/bugs/524948
The OR has verified that the existing model=laptop-eapd quirk does not
function correctly but instead needs model=3stack. Make this change
so that manual corrections to module-init-tools file(s) are not
required.
Reported-by: Lasse Havelund <lasse@havelund.org>
CC: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
snd_cs46xx_codec_reset() bypassing the register cache, so as to not
clobber the cached register value during resume.
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Conflicts:
sound/pci/hda/patch_realtek.c
|
|
This patch fixes a division by zero error in the irq handler.
There is a small window between the hw_params() callback and when
runtime->frame_bits is set by ALSA middle layer. When another substream is
already running, if an interrupt is delivered during that window the irq
handler calls pcm_pointer() which does a division by zero. The patch below
makes the irq handler skip substreams that are initialized but not started
yet. Cc to Clemens Ladisch because he proposed an alternate fix.
For more information, please read the original thread in the linux-kernel
mailing list: http://lkml.org/lkml/2010/2/2/187
Signed-off-by: Giuliano Pochini <pochini@shiny.it>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6 into devel
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Correct ASUA blacklist for MSI brokenness
|
|
The MSI blacklist entry for ASUS mobo added in the commit
8ce28d6abff34886d3797b25324c940471b99164 was based on the alsa-info
output wrongly posted. Fix the id to the right one now.
Reported-by: Sid Boyce <sboyce@blueyonder.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch adds rearranges parts of the initialization code and adds
suspend and resume callbacks.
This patch adds suspend and resume callbacks.
It also rearranges parts of the initialization code so it can be
used in both the first initialization (when the module is loaded we
also have to load default settings) and the resume callback (where
we have to restore the previous settings).
Signed-off-by: Giuliano Pochini <pochini@shiny.it>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Move the controls init code outside the init_hw() function because is must
not be called during resume.
This patch moves the code that initializes the card's controls with
default valued from the init_hw() function into a separated
set_mixer_defaults() function (one for each of the 16 supported
cards). This change is necessary because during resume we must
resurrect the hardware without losing the previous
settings. set_mixer_defaults() must be called only once when the
module is loaded.
Signed-off-by: Giuliano Pochini <pochini@shiny.it>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch implements a simple cache for the firmware files when CONFIG_PM is defined.
This patch changes get_firmware(), free_firmware() and adds
free_firmware_cache(). The first two functions implement a very
simple cache and the latter is used to actually release all the stored
firmwares when the module is unloaded.
When CONFIG_PM is not enabled those functions act as before, that is
free_firmware() releases the firmware immediately and
free_firmware_cache() does nothing.
Signed-off-by: Giuliano Pochini <pochini@shiny.it>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Changes the way the firmware is passed through functions.
When CONFIG_PM is enabled the firmware cannot be released because the
driver will need it again to resume the card.
With this patch the firmware is passed as an index of the struct
firmware card_fw[] in place of a pointer. That same index is then used
to locate the firmware in the firmware cache.
Signed-off-by: Giuliano Pochini <pochini@shiny.it>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add patch for the Conexant 5066 HDA codec to support the Lenovo IdeaPad U150
Signed-off-by: Greg Alexander <greigs@galexander.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - use WARN_ON_ONCE() for zero-division detection
|
|
Replace the zero-division warning message with WARN_ON_ONCE() per the
advice by Linus. This shouldn't happen, but if it happens, it's
possible that the bug happens often due to buggy IRQs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda-intel: Avoid divide by zero crash
|
|
|
|
On my AMD780V chipset, hda_intel.c can crash the kernel with a divide by
zero
for as-yet unknown reasons. A simple check for zero prevents it, though
the problem that causes it remains. Since the workaround is harmless and
won't affect anyone except victims of this bug, it should be safe;
moreover,
because this crash can be triggered by a user-mode application, there are
denial of service implications on the systems affected by the bug without
the patch.
Signed-off-by: Jody Bruchon <jody@nctritech.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Use DEFINE_PCI_DEVICE_TABLE() to make PCI device ids go to
.devinit.rodata section, so they can be discarded in some cases,
and make them const.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The previous commit caused a regression on HP laptops with 92HD83x/88x
codecs. The default polarity of mute-LED GPIO is inverted on these
devices.
Reference: Novell bnc#578190
https://bugzilla.novell.com/show_bug.cgi?id=578190
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
We have now a better mute-LED GPIO detection, and no need to assign the
values statically per model option.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Merge the mute-LED status callback function for both IDT 92HD7x and 8x
codecs to one function. Also it's changed to check all DACs, and called
in the initialization to sync with the current status.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The GPIO pin number for the mute LED control on HP laptops can be
determined more easily by checking the number of available GPIO pins
of the codec chip. On a small package with up to 3 GPIOs, GPIO 0 is
used while GPIO 3 is used for others.
This fixes the missing mute GPIO for some HP laptops with new codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
The volume register is from 0..0x7f and 0..0x1a range is mute.
Also, fix mute combining in wm_vol_put(). The wrong behaviour was
noticed by Peter Christensen.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
|
|
This renames the interrupt name in /proc/interrupt.
HDA Intel -> hda_intel
This also eliminates space from the name, probably helping some
parsers.
Don't think anybody depends on this name in userspace
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
My sound codec seems sometimes (very rarely) to omit interrupts (ALC268)
However, interrupt mode still works.
Thus if we get timeout, poll the codec once.
If we get 3 such polls in a row, then switch to polling mode.
This patch is maybe an bandaid, but this might be a workaround for hardware bug.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
I found that the sampling rate locking setting of the ice1712 sound driver
was only half-respected : when the driver was locked to, let's say, 44100Hz,
and a usermode app was requesting 48000Hz playback, the request was succesful
although the soundcard would continue to run at 44100Hz.
Here's a patch that will make those requests to fail.
Signed-off-by: Sebastien Alaiwan <sebastien.alaiwan@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
After hours of debugging, I finally found the reason why some source
and runtime combination does not work. The PTP (page table pages)
address must be aligned. I am not sure how much, but alignment to
PAGE_SIZE is sufficient. Also, use ALSA's page allocation routines
to ensure proper virtual -> physical address translation.
Cc: <stable@kernel.org>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
- Add support for ALC665
- Add more ASUS model
- Modify common patch for ALC272 ALC273 ALC661 ALC662 ALC663 ALC665
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
- Add new models ALC269VB_AMIC ALC269VB_DMIC
- Add alc269vb_laptop_dmic_setup
The record source index Dmic is 0x6 for ALC269VB.
- Change eeepc words for ALC269
- Modify init_verb tables of patch_alc269 patch_alc662 patch_alc882
- Modify common patch for ALC270 ALC269VB ALC275
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The default values are no need to be set in init_verbs.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch fixes docking output support for IDT 92HD81/83/88 family codecs.
Typically one of ports 0xE or 0xF is used for docking output, while only
port 0xF is common on all the three codec families. We don't want the
pin to select the analog mixer here.
Signed-off-by: Charles Chin <Charles.Chin@idt.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Vitaliy Kulikov <Vitaliy.Kulikov@idt.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Charles Chin <Charles.Chin@idt.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch adds HP mute LED support for IDT 92HD81/3 family of the codecs.
Signed-off-by: Vitaliy Kulikov <Vitaliy.Kulikov@idt.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The amp used for the mic input on HP Compaq F700 with Cxt5051 codec
has no multiple inputs, thus its index should be 0 instead of 1.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|