| Age | Commit message (Collapse) | Author |
|---|
|
Fix the ordering problem in DAPM domain, when the user
changes between digital and analog sources during active
capture (or loopback) scenario.
Before this patch, when the user changed from analog source
to digital there were a short time, when the codec enabled
analog mic bias (2.2 volts) instead of the correct digital
mic bias (1.8 volts) to the digital microphones.
This behaviour caused by the former implementation of
selecting the correct type of bias. This was done at the
POST_REG event of the DAPM_MUX_E("TXx Capture Route")
widget.
By moving the bias type selection as DAPM_SUPPLY and
connecting it to the corresponding digimic widget the
problematic situation can be avoided.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
An Intel board needs a white-list entry to enable PC-beep.
Otherwise the driver misdetects (due to bogus BIOS info) and ignores
the PC-beep on 2.6.35.
Reported-and-tested-by: Leandro Lucarella <luca@llucax.com.ar>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Since the pending periods are often bogus and take long time until
actually processed, it often results in a high CPU usage of the hd-audio
workq. Overall it's better to have low CPU consumption by avoiding a
too tight loop rather than the wake-up timing accuracy.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Define constants for the HD-audio stream format bits, and replace the
magic numbers in codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fix HDA beep frequency on IDT 92HD73xx and 92HD71Bxx codecs.
These codecs use the standard beep frequency calculation although the
datasheet says it's linear frequency.
Other IDT/STAC codecs might have the same problem. They should be
fixed individually later.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Passing IEC 61937 encapsulated compressed audio at bitrates over 6.144
Mbps (i.e. more than a single 2-channel 16-bit 192kHz IEC 60958 link)
over HDMI requires the use of HBR Audio Stream Packets instead of Audio
Sample Packets.
Enable HBR mode when the stream has 8 channels and the Non-PCM bit is
set.
If the audio converter is not connected to any HBR-capable pins, return
-EINVAL in prepare().
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Set bit 15 (Stream Type) of HDA Stream Format to 1 (Non-PCM) when IEC958
channel status bit 1 (AES0 & 0x02) is set to 1 (non-audio).
This is a prequisite for HDMI HBR passthrough.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Instead of io_req_t, drivers are now requested to fill out
struct pcmcia_device *p_dev->resource[0,1] for up to two ioport
ranges. After a call to pcmcia_request_io(), the ports found there
are reserved, after calling pcmcia_request_configuration(), they may
be used.
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-ide@vger.kernel.org
CC: linux-usb@vger.kernel.org
CC: laforge@gnumonks.org
CC: linux-mtd@lists.infradead.org
CC: alsa-devel@alsa-project.org
CC: linux-serial@vger.kernel.org
CC: Michael Buesch <mb@bu3sch.de>
Acked-by: Marcel Holtmann <marcel@holtmann.org> (for drivers/bluetooth/)
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
After pcmcia_request_io(), do not make use of the values stored in
io_req_t, but instead use those found in struct pcmcia_device->resource[].
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-ide@vger.kernel.org
CC: linux-usb@vger.kernel.org
CC: laforge@gnumonks.org
CC: linux-mtd@lists.infradead.org
CC: alsa-devel@alsa-project.org
CC: linux-serial@vger.kernel.org
Acked-by: Marcel Holtmann <marcel@holtmann.org> (for drivers/bluetooth/)
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
Just as with the X301. The X300 does not have a way to do SPDIF either.
It does not have a dock connector, nor does it have the SPDIF through
the headphone jack.
This patch fixes it so X300 does not show SPDIF, since it cannot do it.
To add all Lenovo Thinkpads had different codec subsytem IDs:
X300:
http://launchpadlibrarian.net/34862838/Card0.Codecs.codec.0.txt
Signed-off-by: Jerone Young <jerone.young@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
the ability to use SPDIF
The Lenovo X301 does not have the ability to connect to a docking
station to use the SPDIF port. It also does not have the ability to do
SPDIF though the headphone jack or Display Port jacks.
This patch fixes it so this is not exposed for the X301 and users do
think it has the ability to do SPDIF.
I tested both headphone & display port jacks and it is not there. I have
tested this patch and it works great.
Also to add the other Thinkpads have different subsystem codec IDs.
Here are examples:
X301:
http://launchpadlibrarian.net/31561902/Card0.Codecs.codec.0.txt
X200:
http://launchpadlibrarian.net/49055036/Card0.Codecs.codec.0.txt
W500:
http://launchpadlibrarian.net/36276057/Card0.Codecs.codec.0.txt
Signed-off-by: Jerone Young <jerone.young@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch fixes the error path in wm9081_register to properly free resources.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
There is a memory leak found if wm8978_register() fail.
This patch moves the buffer allocate and release
at the same level to prevent the memory leak.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
wm8974 is allocated in wm8974_i2c_probe() but is not freed if wm8974_register()
return -EINVAL (if another WM8974 is registered).
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
This patch fixes the error path in wm8961_register to properly free resources.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
This patch fixes the error path in wm8955_register to properly free resources.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
This patch adds checking for wm8940_register return value,
and does kfree(wm8940) if wm8940_register() fail.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
This patch includes below fixes:
1. wm8904 need to be kfreed in wm8904_register() error path before return.
2. fix the error path for snd_soc_register_codec() fail and
snd_soc_register_dai() fail to properly free resources.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
wm8711 is allocated in either wm8711_spi_probe() or wm8711_i2c_probe() but is
not freed if wm8711_register() return -EINVAL(if another ad1836 is registered).
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
This patch includes below fixes:
1. If another WM8523 is registered, need to kfree wm8523 before return -EINVAL.
2. If snd_soc_register_codec failed, goto error path to properly free resources.
3. Instead of using mixed in-line and goto style cleanup, use goto style error
handling if snd_soc_register_dai failed.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
da7210 should be kfreed if da7210_init() return error.
This patch also fixes the error handing in the case of snd_soc_register_dai()
fail by adding snd_soc_unregister_codec() in error path.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
ak4642 should be kfreed if ak4642_init() return error.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Reviewed-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
ad1836 is allocated in ad1836_spi_probe() but is not freed if ad1836_register()
return -EINVAL (if another ad1836 is registered).
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The WM8741 is a very high performance stereo DAC designed for audio
applications such as professional recording systems, A/V receivers and
high specification CD, DVD and home theatre systems. The device supports
PCM data input word lengths from 16 to 32-bits and sampling rates up to
192kHz. The WM8741 also supports DSD bit-stream data format, in both
direct DSD and PCM-converted DSD modes.
TODO: Expand wm8741_set_dai_sysclk and rate_constraint members to
allow for all supported sample rate / Master Clock frequency combinations.
Fully enable control of supplies.
Signed-off-by: Ian Lartey <ian@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lrg/asoc-2.6 into topic/asoc
|
|
The use of sDMA packet mode in THRESHOLD mode removes the restriction on the
period size.
With the extended THRESHOLD mode user space can ask for any
period size it wishes, and the driver will configure the
sDMA and McBSP FIFO accordingly.
Replace the hw_rule for the period size with static constraint,
which will make sure that the period size will be always
even (to avoid prime period size, which could be possible in
mono stream)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
Utilize the sDMA controller's packet syncronization mode, when
the McBSP FIFO is in use (by extending the THRESHOLD mode).
When the sDMA is configured for packet mode, the sDMA frame size
does not need to match with the McBSP threshold configuration.
Uppon DMA request the sDMA will transfer packet size number of
words, and still trigger interrupt on frame boundary.
The patch extends the original THRESHOLD mode by doing the
following:
if (period_words <= max_threshold)
Current THRESHOLD mode configuration
Otherwise (period_words > max_threshold)
McBSP threshold = sDMA packet size
sDMA frame size = period size
With the extended THRESHOLD mode we can remove the constraint
for the maximum period size, since if the period size is
bigger than the maximum allowed threshold, than the driver
will switch to packet mode, and picks the best (biggest)
threshold value, which can divide evenly the period size.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
To make the code a bit more readable, change the indexed
references to the omap_mcbsp_dai_dma_params elements with
pointer.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
In preparation for the extended threshold mode (sDMA packet mode
support), the code need to be restructured.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
urb data align
Match usb ids in usb/quirks-table.h for some Hauppage HVR-950Q models
and for the HVR850 model to those ids at the end of au0828-cards.c
Thanks to nhJm449 for pointing out the problem.
Signed-off-by: John S Gruber <JohnSGruber@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Remove cs_types.h which is no longer needed: Most definitions aren't
used at all, a few can be made away with, and two remaining definitions
(typedefs, unfortunatley) may be moved to more specific places.
CC: linux-ide@vger.kernel.org
CC: linux-usb@vger.kernel.org
CC: laforge@gnumonks.org
CC: linux-mtd@lists.infradead.org
CC: alsa-devel@alsa-project.org
CC: linux-serial@vger.kernel.org
Acked-by: Marcel Holtmann <marcel@holtmann.org> (for drivers/bluetooth/)
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
The current ALC259/268/269 parser ignores some pins as unhandled,
but user won't notice what goes wrong. So, added a warning message
for the ignored pins as a hint.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The pin NID 0x1a should be handled as well as NID 0x1b.
Also added comments.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Call snd_hda_shutup_pins() for power-saving and reboot-notifier in
patch_conexant.c as well as other codecs. This will reduce the pop
noise in power-save mode.
Reference: bnc#624896
https://bugzilla.novell.com/show_bug.cgi?id=624896
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
If BIOS sets up the input pin as VREF 50, use the value as is instead of
overriding forcibly to VREF 80. This fixes the quality of inputs on
some devices like Packard-Bell M5210.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Since ALC259/269 use the same parser of ALC268, the pin 0x1b was ignored
as an invalid widget. Just add this NID to handle properly.
This will add the missing mixer controls for some devices.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Make a helper function to parse the digital I/Os of all Realtek codecs
to simplify the code and to ensure the setups.
Also, initialize digital I/O pins properly in init callbacks. Some BIOS
seem to leave pins uninitialized.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Some ALC662-compatible codecs like ALC892 may have more than 4
connections for the input source. Use HDA_MAX_CONNECTIONS instead of
the fixed magic number 4.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add a prefix and more information for error messages regarding the
connection-list in hda_codec.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Add a PC-beep workaround for ASUS P5-V
ALSA: hda - Assume PC-beep as default for Realtek
ALSA: hda - Don't register beep input device when no beep is available
ALSA: hda - Fix pin-detection of Nvidia HDMI
|
|
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Current FSI driver id is not only 0
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The non-standard name "iMic" makes PulseAudio ignore the microphone.
BugLink: https://launchpad.net/bugs/605101
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
ASUS P5-V provides a SSID that unexpectedly matches with the value
compilant with Realtek's specification. Thus the driver interprets
it badly, resulting in non-working PC beep.
This patch adds a white-list for such a case; a white-list of known
devices with working PC beep.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
request_region() may fail, if so return -EBUSY.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
request_region() may fail, if so return -EBUSY.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
get_user() may fail, if so return -EFAULT.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
