| Age | Commit message (Collapse) | Author |
|---|
|
Modules: NM256 driver
The current snd-nm256 driver can cause Dell Latitude CSx laptops to
lock-up during module (un)load. I have isolated this to the writes to
the control port register at offset 0x6cc which were not already
protected by the existing reset_workaround.
I tried grouping these writes with the existing reset_workaround
clause, but that caused the driver to have (un)load problems on the
Dell Latitude LS laptops. So, I have implemented a reset_workaround_2
clause (please feel free to suggest a better name!) to cover this
situation and added a quirk entry for the CSx laptops.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: YMFPCI driver
We better pretend that the ymfpci timer runs at 48 kHz because the
interrupt frequency cannot be higher, and clients that would try to
use 96 kHz would run at half their desired speed.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Modules: ALSA sequencer
When no default timer frequency has been set, initialize_timer() just
uses the maximum frequency supported by the timer, which is ridiculously
high on 96 kHz timers.
This patch introduces a default frequency of 1000 Hz for this case, and
makes sure that a frequency set by the user isn't too high.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Modules: Maestro3 driver
This patch fixes the maestro3 driver to call the snd_m3_assp_init
function to write the DSP firmware into the ASSP chip before sending the
RUN_ASSP command, thereby solving the hang after a cold boot.
Signed-off-by: Charles R. Anderson <cra@alum.wpi.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: Intel8x0 driver
- Set buggy_irq parameter before registration of irq handler.
- Clean up module parameter handling.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: VIA82xx driver
The change only affects the via823x kind of chips.
Here the via8233_pcm_pointer_hw() function
(named snd_via8233_pcm_pointer() before)
needed to loop until a non zero position is red from the chip.
Measurements have shown that more than 200 loops are typically needed on
an Athlon64.
As io-reads cost many cycles, those loops sum up huge.
via8233_pcm_pointer_hw() runs either in interrupt or with interrupts
disabled. So it introduces significant interrupt latency.
The patch introduces a calculated position value hwptr_done,
that is updated by the interrupt routine when a period is completed.
It is only used, if the 823x chip returns a zero position, which can't
be interpreted reliably.
Further optimisation is applied on the 8233 chip's interrupt routine:
Only the SGD_SHADOW is read, as it contains all infos needed.
We ommit ~5 more register reads that way.
Signed-off-by: Karsten Wiese <annabellesgarden@yahoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: USB generic driver
Remove the usb_reset_configuration() call from the probe callback
because it isn't needed and it may interfere with other drivers
already loaded for the device.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Modules: VIA82xx driver
The patch enable separate DXS controls of sound function of VIA VT82xx
controller in case DXS volume is not needed for PCM Playback volume
control emulation.
Signed-off-by: Honza Maly <hkmaly@matfyz.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: Documentation,MIPS AU1x00 driver,PPC Beep,SPARC DBRI driver
Removed the use of chip_t, which was obsoleted.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: Timer Midlevel
Split or rewrite lines that are longer than 80 characters, and remove
whitespaces at the end of lines.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Modules: Timer Midlevel
The return value of list_entry() already has the type from the second
argument, so we don't need to typecase it again.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Modules: RTC timer driver,Timer Midlevel
Add a module pointer to the timer structure and use it for refcounting
instead of the card's module pointer to prevent the global timer
modules (rtctimer and hpetimer) from being removed while in use.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Modules: Timer Midlevel
Add checks to return -ENOMEM in case snd_timer_instance_new() fails.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Modules: ICE1724 driver
Add support of SPDIF output with sample rates higher than 48kHz.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
Get subsytem ID from AFG/MFG if not obtained from the root node.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: ES1938 driver
- Clean up the last PM fix
- Add TRIGGER_SUSPEND/RESUME to disable/enable DMA properly during PM
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: ES1938 driver
This patch fixes the suspend/resume issue I'm having with ESS-Solo1
soundcard. Without this patch I might get after resume message
that kernel is disabling the IRQ5 (soundcard). If there was something
playing it wont continue after resume without this patch.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: VIA82xx driver
Added the DXS entry for Clevo D470 laptop.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: ALSA Core
Remove kmalloc wrappers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
- Remove vmalloc wrapper
- Add release_and_free_resource() to remove kfree_nocheck() from each driver
and simplify the code
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: ALSA Core,ALSA<-OSS emulation
Remove a global function snd_task_name(), and move it local
to snd-pcm-oss module.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: Documentation,PCM Midlevel,Timer Midlevel,ALSA Core
Use the standard getnstimeofday() function instead of ALSA's own one.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Remove snd_runtime_check() macro.
This macro worsens the readability of codes. They should be either
normal if() or removable asserts.
Also, the assert displays stack-dump, instead of only the last caller
pointer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: Intel8x0-modem driver,VIA82xx-modem driver,HDA Codec driver
Signed-off-by: Sasha Khapyorsky <sashakh@alsa-project.org>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Modules: Intel8x0 driver
On my Acer Aspire 3003LCi laptop, the speaker volume is not controlled
by the master control, but by the headphone control. Enabling the
'hp_only' quirk corrects this. The patch below adds this device to the
list of known quirks.
Signed-off-by: Dick Streefland <dick@streefland.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: ICE1724 driver
Remove the restcition of sample rates on Revolution 7.1 board.
This enables the low 8-44kHz sample rates.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Added dummay obsoleted module options for backward compatibility
(to reduce possible bugzilla entries :)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: Intel8x0 driver
Suppress the codec warnings during probing of codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Remove the code for supporting eight cards from the integrated
controller drivers because There Can Be Only One controller of
each type per mainboard.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Modules: Sound Core,PCI drivers
AC97 Kconfig entries broke the ALSA device drivers menu,
so move them to a location where that won't happen,
enabling all device sub-menus to be presented together.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch cleans last ac97 audio/modem codec interception in
initialization procedures (ac97_mixer_new()) and removes obsolete
SHARED_TYPE 'locking' which prevents from AMC codecs to function
correctly.
Signed-off-by: Sasha Khapyorsky <sashak@smlink.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
dev_class=SNDRV_PCM_CLASS_MODEM for all supported softmodem PCMs
Signed-off-by: Sasha Khapyorsky <sashak@smlink.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: YMFPCI driver
This patch adds a new mixer control called 'IEC958 Loop' which makes
it possible to loop digital signals from S/PDIF-in to S/PDIF-out.
Signed-off-by: Glen Masgai <mimosius@gmx.de>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Modules: ALSA sequencer
Remove the last parameter of snd_seq_timer_set_tick_resolution()
because it is always one.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Modules: RTC timer driver
The check whether rtctimer_freq is a power of two can be done easier
with a simple bit operation.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Modules: RTC timer driver
The rtc_inc variable is never used outside the interrupt handler, and
is always one where it matters, so we can just remove it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Modules: USB generic driver
Move the usb_complete_callback() compatibility wrapper out of the
kernel tree.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Modules: USB generic driver
Move the usb_pipe_needs_resubmit() compatibility wrapper out of the
kernel tree.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Modules: USB generic driver
Add more comments about other device modes and unsupported devices to
the Roland part of the quirks table.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Modules: au88x0 driver
This patch extends au88x0 AC97 codec access procedures to handle multiple
codecs properly.
Signed-off-by: Sasha Khapyorsky <sashak@smlink.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver
Added a new model 'fujitsu' to ALC260 config for Fujitsu S7020.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: USB generic driver
Add a quirk entry for the Hercules DJ Console to ignore timeouts on
some mixer control transfers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Modules: USB generic driver
Simplify the handling of MIDI quirks by treating an interface without
quirks as a QUIRK_MIDI_STANDARD_INTERFACE.
This also fixes the bug where a MIDI_STANDARD quirk would not be
recognized.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Modules: CMIPCI driver
If possible, use ports in the card's PCI port address range instead of
the legacy ports.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Modules: HDA Intel driver
This patch is to make the Intel HDA code work for NVIDIA azalia controller.
Modified by Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vinod G. <vinodg@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: AC97 Codec
Fix a typo in the last patch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: AC97 Codec
- Fixed surround controls of CMI9761 (model 83) in update_jacks callback.
- Clean up ad1888 and ad1985 update_jacks callbacks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: EMU10K1/EMU10K2 driver
Adds left and right front channel outputs using fxbus 8 and 9 and 'Front'
playback and capture volume controls.
Signed-off-by: Mikael Magnusson <mikma@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This adds the magic IO wakeup code for the CardBus version of the
Creative Labs Audigy 2 to the snd-emu10k1 driver.
Without the magic IO enable sequence, reading from the IO region of the
card will fail spectacularly, and the machine will hang.
My next task will be getting the driver to actually play sound without
distortion.
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
[ This is a work-in-progress, but since it avoids a total lockup
if the emu10k module is loaded on a machine with the cardbus
card inserted, we're better off with it than without it, even
if sound quality is bad right now ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Manual #include fixups for clashes - there may be some unnecessary
|
