| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull PTR_RET() removal patches from Rusty Russell:
"PTR_RET() is a weird name, and led to some confusing usage. We ended
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle"
[ There are still some PTR_RET users scattered about, with some of them
possibly being new, but most of them existing in Rusty's tree too. We
have that
#define PTR_RET(p) PTR_ERR_OR_ZERO(p)
thing in <linux/err.h>, so they continue to work for now - Linus ]
* tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
GFS2: Replace PTR_RET with PTR_ERR_OR_ZERO
Btrfs: volume: Replace PTR_RET with PTR_ERR_OR_ZERO
drm/cma: Replace PTR_RET with PTR_ERR_OR_ZERO
sh_veu: Replace PTR_RET with PTR_ERR_OR_ZERO
dma-buf: Replace PTR_RET with PTR_ERR_OR_ZERO
drivers/rtc: Replace PTR_RET with PTR_ERR_OR_ZERO
mm/oom_kill: remove weird use of ERR_PTR()/PTR_ERR().
staging/zcache: don't use PTR_RET().
remoteproc: don't use PTR_RET().
pinctrl: don't use PTR_RET().
acpi: Replace weird use of PTR_RET.
s390: Replace weird use of PTR_RET.
PTR_RET is now PTR_ERR_OR_ZERO(): Replace most.
PTR_RET is now PTR_ERR_OR_ZERO
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"Changes are seen in a wide range of codes, mainly due to ASoC DAPM
requirements; HD-audio shows a high peak in diffstat, it's just a
removal of bunch of old static quirks.
Some highlights:
- HDPM: Updates for AIO/RayDAT support, TCO/sync support
- RME96: Add PCM sync support
- HD-audio:
* A few HDMI/DP audio updates (CA assignment fix, stream switching
fix, Intel DP device list support)
* Device specific fixes (ASUS/CXT HP mic support, Thinkpad mic
improvements, Chromebook fixes, STAC9228 Dell fixes)
* Replace the all static quirks for AD codecs with the generic
parser
* WAKEEN support for handling irqs in the power saving mode
- USB-audio: Clean up implicit fb handling and related codes
- DAPM is now mandatory for ASoC CODEC drivers; all existing drivers
have had some level of DAPM support added. In addition, a lot of
cleanups and improvements in DAPM.
- Support for ASoC cross-platform compile test
- New drivers and support for Analog Devices ADAU1702 and
ADAU1401(a), Asahi Kasei Microdevices AK4554, Atmel AT91ASM9x5 and
WM8904 based machines, Freescale S/PDIF and SSI AC'97, Renesas
R-Car SoCs, Samsung Exynos5420 SoCs, Texas Instruments PCM1681 and
PCM1792A and Wolfson Microelectronics WM8997
- DT bindings for kirkwood and i.MX S/PDIF
- Clean up and bug fixes: ssm2602, rt5640 and sgtl5000.
- Core helpers for bitbanged AC'97 reset"
* tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (375 commits)
ALSA: hda - Re-setup HDMI pin and audio infoframe on stream switches
ALSA: hda - hdmi: Fallback to ALSA allocation when selecting CA
ASoC: mxs-sgtl5000: Configure the dai_links as unidirectional
ASoC: soc-pcm: Allow to specify unidirectional dai_link
ASoC: fsl_spdif: Staticse non-exported symbols
ASoC: ssm2602: Fix cache sync
ASoC: Remove unused sysfs_registered field from snd_soc_codec struct
ASoC: Remove unused debugfs_dapm field from snd_soc_{platform,codec} struct
ASoC: Remove unused control_type field from snd_soc_codec struct
ASoC: fsl: Add one blank space after ':=' in Makefile
ASoC: fsl: Add wrapping for dev_dbg() in fsl_spdif.c
ASoC: rt5640: change widget sequence for depop
ASoC: dapm: Fix auto-disable for inverted controls
ASoC: fsl: Drop SND_SOC_FSL_UTILS from SND_SOC_IMX_SPDIF
ASoC: Samsung: Do not queue cyclic buffers multiple times
ASoC: ep93xx-i2s: Remove unnecessary dev_set_drvdata()
ASoC: designware_i2s: Remove unnecessary dev_set_drvdata()
ASoC: fsl_spdif: remove redundant dev_err call in fsl_spdif_probe()
ASoC: fsl: Add S/PDIF machine driver
ASoc: kirkwood: Use the Kirkwood audio driver in Dove boards
...
|
|
As once the error interrupt is triggered, it can not be cleared.
So, disable it.
No side effect found while testing on sama5d3xek and at91sam9x5ek
boards.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
kernel
Booting a mx51babbage board with a non-dt kernel leads to the following crash:
Unable to handle kernel NULL pointer dereference at virtual address 0000001c
pgd = 80004000
[0000001c] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.11.0-next-20130903 #287
task: 9f860000 ti: 9f862000 task.ti: 9f862000
PC is at of_get_next_available_child+0x5c/0x68
LR is at of_get_next_available_child+0x1c/0x68
pc : [<8043ea58>] lr : [<8043ea18>] psr: 60000193
sp : 9f863d58 ip : 00000000 fp : 9f863d74
r10: 9f89a010 r9 : 9f862000 r8 : 807bb26c
r7 : 80615d5c r6 : 00000000 r5 : 60000113 r4 : 00000000
r3 : 00000000 r2 : 808770a4 r1 : 00000011 r0 : 60000113
Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c5387d Table: 90004019 DAC: 00000017
Process swapper/0 (pid: 1, stack limit = 0x9f862240)
Stack: (0x9f863d58 to 0x9f864000)
This is caused by commit 8548a464b9 (ASoC: imx-audmux: Read default
configuration from devicetree).
In order to fix this, add a check for 'of_id' so that
imx_audmux_parse_dt_defaults() only gets called when a dt kernel is running.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
When the transcoder:port mapping on Haswell HDMI/DP audio is changed
during the stream playback, the sound gets lost. Typically this
problem is seen when the user switches the graphics mode from eDP+DP
to DP-only configuration, where CRTC 1 is used for DP in the former
while CRTC 0 is used for the latter.
The graphics controller notifies the change via the normal ELD update
procedure, so we get the intrinsic event. For enabling the sound
again, the HDMI audio driver needs to reset the pin and set up the
audio infoframe again.
This patch achieves it by:
- keep the current status of channels and info frame setup in per_pin
struct,
- check the reconnection in the intrinsic event handler,
- reset the pin and the re-invoke hdmi_setup_audio_infoframe()
accordingly.
The hdmi_setup_audio_infoframe() function has been changed, too, so
that it can be invoked without passing the substream instance.
The patch is mostly based on the work by Mengdong Lin.
Cc: Mengdong Lin <mengdong.lin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Final updates for v3.12
A few final updates for v3.12 - some cleanups, a bug fix for ssm2602,
pop removal for rt5640 and fixes for the reporting of unidirectional
links in the MXS SGTL5000 driver.
|
|
hdmi_channel_allocation() tries to find a HDMI channel allocation that
matches the number channels in the playback stream and contains only
speakers that the HDMI sink has reported as available via EDID. If no
such allocation is found, 0 (stereo audio) is used.
Using CA 0 causes the audio causes the sink to discard everything except
the first two channels (front left and front right).
However, the sink may be capable of receiving more channels than it has
speakers (and then perform downmix or discard the extra channels), in
which case it is preferable to use a CA that contains extra channels
than to use CA 0 which discards all the non-stereo channels.
Additionally, it seems that HBR (HD) passthrough output does not work on
Intel HDMI codecs when CA is set to 0 (possibly the codec zeroes
channels not present in CA). This happens with all receivers that report
a 5.1 speaker mask since a HBR stream is carried on 8 channels to the
codec.
Add a fallback in the CA selection so that the CA channel count at least
matches the stream channel count, even if the stream contains channels
not present in the sink speaker descriptor.
Thanks to GrimGriefer at OpenELEC forums for discovering that changing
the sink speaker mask allowed HBR output.
Reported-by: GrimGriefer
Reported-by: Ashecrow
Reported-by: Frank Zafka <kafkaesque1978@gmail.com>
Reported-by: Peter Frühberger <fritsch@xbmc.org>
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
into drm-next
Alex writes:
This is the radeon drm-next request. Big changes include:
- support for dpm on CIK parts
- support for ASPM on CIK parts
- support for berlin GPUs
- major ring handling cleanup
- remove the old 3D blit code for bo moves in favor of CP DMA or sDMA
- lots of bug fixes
[airlied: fix up a bunch of conflicts from drm_order removal]
* 'drm-next-3.12' of git://people.freedesktop.org/~agd5f/linux: (898 commits)
drm/radeon/dpm: make sure dc performance level limits are valid (CI)
drm/radeon/dpm: make sure dc performance level limits are valid (BTC-SI) (v2)
drm/radeon: gcc fixes for extended dpm tables
drm/radeon: gcc fixes for kb/kv dpm
drm/radeon: gcc fixes for ci dpm
drm/radeon: gcc fixes for si dpm
drm/radeon: gcc fixes for ni dpm
drm/radeon: gcc fixes for trinity dpm
drm/radeon: gcc fixes for sumo dpm
drm/radeonn: gcc fixes for rv7xx/eg/btc dpm
drm/radeon: gcc fixes for rv6xx dpm
drm/radeon: gcc fixes for radeon_atombios.c
drm/radeon: enable UVD interrupts on CIK
drm/radeon: fix init ordering for r600+
drm/radeon/dpm: only need to reprogram uvd if uvd pg is enabled
drm/radeon: check the return value of uvd_v1_0_start in uvd_v1_0_init
drm/radeon: split out radeon_uvd_resume from uvd_v4_2_resume
radeon kms: fix uninitialised hotplug work usage in r100_irq_process()
drm/radeon/audio: set up the sads on DCE3.2 asics
drm/radeon: fix handling of variable sized arrays for router objects
...
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_gem_dmabuf.c
drivers/gpu/drm/i915/intel_pm.c
drivers/gpu/drm/radeon/cik.c
drivers/gpu/drm/radeon/ni.c
drivers/gpu/drm/radeon/r600.c
|
|
|
|
|
|
|
|
On a mx28 board, running "aplay -l" and "arecord -l" results in the following:
$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: mxssgtl5000 [mxs_sgtl5000], device 0: Playback sgtl5000-0 []
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: mxssgtl5000 [mxs_sgtl5000], device 1: Capture sgtl5000-1 []
Subdevices: 1/1
Subdevice #0: subdevice #0
$ arecord -l
**** List of CAPTURE Hardware Devices ****
card 0: mxssgtl5000 [mxs_sgtl5000], device 0: Playback sgtl5000-0 []
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: mxssgtl5000 [mxs_sgtl5000], device 1: Capture sgtl5000-1 []
Subdevices: 1/1
Subdevice #0: subdevice #0
,which is not correct because we got a capture device listed in aplay and a
playback device listed in arecord.
On mx28 there are two serial audio interface ports (SAIF0 and SAIF1) and each
one of them are unidirectional.
Allow to specify a dai link as 'playback_only' or 'capture_only', which suits
well for this case.
After this change we can correctly report the capabilities as follows:
$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: mxssgtl5000 [mxs_sgtl5000], device 0: HiFi Playback sgtl5000-0 []
Subdevices: 1/1
Subdevice #0: subdevice #0
$ arecord -l
**** List of CAPTURE Hardware Devices ****
card 0: mxssgtl5000 [mxs_sgtl5000], device 1: HiFi Capture sgtl5000-1 []
Subdevices: 1/1
Subdevice #0: subdevice #0
Also tested playback and capture on the mx28evk board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Add 'playback_only' and 'capture_only' fields that can be used for specifying
that a dai_link has a unidirectional capability.
The motivation for this is for the cases of systems, such as Freescale MX28,
that has two unidirectional DAIs.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Nicolin Chen <B42378@freescale.com>
|
|
The ssm2602 uses regmap for caching not soc-cache, so we need to use
regcache_sync() instead of snd_soc_cache_sync().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
There is a blank space missing between ':=' and 'imx-spdif.o', thus add it.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Add wrapping '\n' for dev_dbg() in fsl_spdif.c
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Signed-off-by: Bard Liao <bardliao@realtek.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
|
|
We need to make sure that the control's cached value is initialized to the same
value as the control's widget->on_val. Otherwise updates might be lost.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SND_SOC_FSL_UTILS is only used by PowerPC machines, so let's drop it in the
i.mx case.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The legacy S3C-DMA API required every period of a cyclic buffer to be
queued separately. After conversion of Samsung ASoC to Samsung DMA
wrappers somebody made an assumption that the same is needed for DMA
engine API, which is not true.
In effect, Samsung ASoC DMA code was queuing the whole cyclic buffer
multiple times with a shift of one period per iteration, leading to:
a) severe memory waste - up to 13x times more DMA transfer descriptors
are allocated than needed,
b) possible memory corruption, because further cyclic buffers were out
of the original buffers, due to the offset.
This patch fixes this problem by making the legacy S3C-DMA API use the
same semantics as DMA engine (the whole cyclic buffer is enqueued at
once) and modifying users of Samsung DMA wrappers in cyclic mode to
behave appropriately.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Driver core clears the driver data to NULL after device_release or on probe
failure, so just remove it from here.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Driver core clears the driver data to NULL after device_release or on probe
failure, so just remove it from here.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch implements a device-tree-only machine driver for Freescale
i.MX series Soc. It works with spdif_transmitter/spdif_receiver and
fsl_spdif.c drivers.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Add support for HDMI audio device on VGA cards that powerdown
to D3cold using non-standard ACPI/PCI infrastructure (optimus).
This does a couple of things to make it work:
a) add a set of power ops for the hdmi domain, and enables them
via vga_switcheroo when we are a switcheroo controlled card. This
just replaces the runtime resume operation so that when the card
is in D3cold the userspace pci config space access via sysfs,
the vga switcheroon runtime resume gets called first and it calls
the GPU resume callback before calling the sound card runtime
resume.
b) standard ACPI/PCI stacks won't put a device into D3cold without
an ACPI handle, but since the hdmi audio devices on gpus don't have
an ACPI handle, we need to manually force the device into D3cold
after suspend from the switcheroo path only.
c) don't try and do runtime s/r when the GPU is off.
d) call runtime suspend/resume during switcheroo suspend/resume
this is to make sure the runtime stack knows to try and resume
the hdmi audio device for pci config space access.
v2: fix incorrect runtime call suspend->resume.
v3: rework irq handler to avoid false irq when we are resuming
but haven't runtime resumed yet, don't bother trying D3cold,
it won't work, just set it manually ourselves, move runtime s/r
calls outside the main s/r hook. enable dnyamic pm properly by
dropping reference.
v4: put back irq handler check just wrap it with cap check
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The recent commit to delay the release of kobject triggered NULL
dereferences of opti9xx drivers. The cause is that all
snd-opti92x-ad1848, snd-opti92x-cs4231 and snd-opti93x drivers
register the PnP card driver with the very same name, and also
snd-opti92x-ad1848 and -cs4231 drivers register the ISA driver with
the same name, too. When these drivers are built in, quick
"register-release-and-re-register" actions occur, and this results in
Oops because of the same name is assigned to the kobject.
The fix is simply to assign individual names. As a bonus, by using
KBUILD_MODNAME, the patch reduces more lines than it adds.
The fix is based on the suggestion by Russell King.
Reported-and-tested-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch permits the generation of the Kirkwood audio driver which
may be used in the Dove boards.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
snd_soc_dapm_new_widgets() works on the ASoC card as a whole not on a specific
DAPM context. The DAPM context that is passed as the parameter is only used to
look up the pointer to the card. This patch updates the signature of
snd_soc_dapm_new_widgets() to take the card directly.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
|
|
|
|
|
|
snd_soc_dapm_auto_nc_codec_pins()
Call snd_soc_dapm_new_widgets() before the auto non-connected pins have been
marked as not connected will power the system under the assumption that those
pins are connected. Once the pins have been marked as disconnected the system
there will be an additional power run. This can cause unnecessary power
transitions. Calling snd_soc_dapm_new_widgets() only after the pins have been
marked as non-connected avoids this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Each time snd_soc_dapm_new_widgets() is called it will instantiate all the
widgets and routes that have been added so far and then power them. Doing this
multiple times before the card is fully initialized and all widgets have been
added can cause unnecessary and even invalid power state transitions which can
result in extra register writes and and also might cause clicks and pops.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
snd_soc_jack_add_pins() does not create any new DAPM widgets, so there is no
need to call snd_soc_dapm_new_widgets().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The core will call snd_soc_dapm_new_widgets() once all components of the card
have been initialized, so there is no need to do this manually in the driver.
Calling it earlier also might result in a partially instantiated system being
powered up which cause undesired side effects.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Let the core take care of instantiating the controls and DAPM widgets and
routes, this makes the code a bit shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The current calls to dapm_mark_dirty() in snd_soc_dapm_add_path() are on a path
that is only reached if the sink widget is either a mixer or a mux. Move the
calls further up so they are called for all widget types.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Let the core take care of instantiating the DAPM widgets and routes, this makes
the code a bit shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
CONFIG_SND_HDA_I915 doesn't have to be user-selectable as this is almost
mandatory when i915 driver is available. Let's enable it always when
CONFIG_DRM_I915 is set, so that user won't be bothered by useless
questions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch adds two fields to unsolicited response, according to spec HDA040-A:
- Device Entry (bit 20:15)
- Inactive (bit 2)
and show the info in debug message.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
