Age | Commit message (Collapse) | Author |
|
For the CSxxxx and AKxxxx DAC/ADC chips, the MCLK factor in double rate
modes (64-96 kHz) can be reduced to 128x without reducing sound quality.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Replace the get_i2s_mclk callback with tables of MCLK values. This
simplifies the MCLK-handling code in both the framework and the model-
specific drivers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Do not apply the headphone gain offset to any but the front DAC. These
DACs would not be used in headphone mode, so this saves a few register
writes.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Remove the DAC Oversampling mixer control because this setting does not
make much sense.
For cards with the H6 daughterboard, 128x oversampling was disabled
anyway because these high MCLK frequency would not be compatible with
the connector cable.
For cards without the H6 daughterboard, 128x gives a slightly higher
output quality; there is no reason to reduce it to 64x except for saving
power, but then these cards have not been designed to be power efficient
anyway (the D2's blinkenlights cannot be disabled).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Because of the unshielded connector cable, it is important to use as low
a master clock frequency as possible with the H6.
For double rate modes (64-96 kHz), the MCLK rate is unconditionally
lowered from 512x to 256x because the higher rate would not improve
anything.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The clock output of the CS2000, which is used as master clock for the
DACs, was using half the actual master clock frequency for some reason.
Using the theoretically correct frequency seems also to work in practice.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
On the Xonar Essence ST Deluxe, remove all mixer controls that would
require I2C communication with the third DAC, which does not work
because of an addressing conflict with the CS2000 chip.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Change the PCM format used for the PCM1796 from left-justified to I2S to
ensure that the correct format is used even for the Essence ST Deluxe's
center/LFE DAC, where I2C does not work because of an address conflict
with the CS2000 chip.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The PCM1796 needs the master clock for I2C communication to work, so
add delays after clock changes to ensure that the clock is stable when
we try to write the DACs' registers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
To make the I2C communication reliable when using the H6 daughterboard,
reduce the I2C clock frequency.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fix wrong register bits for SPI clock cycle times longer than 160 ns,
and adjust the polling loop timeout for these speeds.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The number of DACs can now be deduced from the dac_channels_mixer field,
so the private_data field is no longer needed.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
For cards like the Xonar HDAV1.3, differentiate between the number of
PCM channels that can be played and the number of channels whose volume
can be adjusted.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
snd_pcm_hw_param_near() will leak the memory allocated to 'save' if the
call to snd_pcm_hw_param_max() returns less than zero.
This patch makes sure we never leak.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
- add some WARN_ONCE
- add multi-I/O helper (and use helper struct)
- fix off-by-1 DMA length bug
- better variable naming
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
- much improved implementation due to clean codec hierarchy
- preparation for potential per-codec spinlock change
NOTE: additionally removes a chip->pcm[codec_type] NULL ptr check
(due to it requiring access to external chip struct),
however I believe this to be ok since this condition should not occur
and most drivers don't check against that either.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
- use a separate variable for the frequency part, don't always "or" it
- use a "clever"(?) macro to shorten the code
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
- correct samples to be POSIX shell compatible
- add logging of jiffies value in _pointer()
- several comments
- cleanup
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
flush_scheduled_work() is deprecated and scheduled to be removed.
* cancel[_delayed]_work() + flush_scheduled_work() ->
cancel[_delayed]_work_sync().
* wm8350, wm8753 and soc-core use custom code to cancel a delayed
work, execute it immediately if it was pending and wait for its
completion. This is equivalent to flush_delayed_work_sync(). Use
it instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
It does not make sense to set clientdata to onyx in onyx_i2c_remove()
as we are going to kfree onyx.
What we really want here is i2c_set_clientdata(client, NULL);
Since the i2c core will take care of it now, so this patch just removes it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Rev. E of the M-Audio Delta 66 is partially supported (commit
ef2cd2ccad66b4aba518eca7514eface267ee0f3), but the layout of the GPIO
pins was still unclear. This patch adds the GPIO definitions so that
communication to the CS8247 & 2x AK4524 works correctly.
ALSA bug#3327 has more details; users cap & jhunt report there that the
GPIO wiring is similar to the Digigram VX442 (chip select: pin 4 =
CS8427, pin 5 = AK4524 #0, pin 6 = AK4524 #1). There has been a lot of
conflicting information in the bug, but given these definitions, my
Delta 66E works; I tested analog in&out at 44.1kHz & 96kHz, analog gain
settings, S/PDIF clock sync, and S/PDIF in&out at 44.1kHz.
Signed-off-by: Brian Bloniarz <brian.bloniarz@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This is a patch to the sound/ac97_bus.c file that fixes up a 80 character
line limit issue found by the checkpatch.pl tool.
Signed-off-by: Jeffrin Jose <ahiliation@yahoo.co.in>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Reformat and update the comments that describe the hardware connections
on the various models.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Instead of the hardcoded "CMI8788", show the actual chip name.
Note: This is neither what the chip is (it's always the same),
nor what the chip is actually called.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
To help with debugging, add the registers of the model-specific
codecs to the controller and AC97 register dump in the proc file.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The "Front Panel" switch on the Xonar D1/DX actually switches only the
output direction, so mark it appropriately.
The front panel microphone is controlled by the FMIC2MIC bit of the
CM9780. It was unconditionally enabled on the D1/DX and never set on
the ST(X); add a control for it. Selecting the front panel microphone
as source does not actually disable the microphone jack, but this is
bug-compatible with the Windows driver, and users rely on it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The GPIO bit that enables analog output on the Xonar HDAV1.3 also
disables the HDMI audio output, so we better add a switch for it.
Hopefully, this is sufficient to make the HDMI output work.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Initialize the configuration of some unknown GPIO output bits (that
might not be used at all) to be the same as in the Windows driver, just
to be sure.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ASoC: omap: N810: Don't select CONFIG_OMAP_MUX but make it as dependency
ALSA: hda: Use "alienware" model quirk for another SSID
ASoC: WM8731: Fix incorrect mask for bypass path disable
s6105-ipcam: fix compilation
s6000-pcm: fix compilation
s6000-i2s: fix compilation
ASoC: Fix missing spin_unlock_irqrestore
ALSA: Fix SNDCTL_DSP_RESET ioctl for OSS emulation
ASoC: Add missing dev_set_drvdata in p1022_ds_probe
ASoC: Add missing dev_set_drvdata in mpc8610_hpcd_probe
ASoC: Remove unneeded !! operations while checking return value of nuc900_checkready
ASoC: Fix compile error for nuc900-pcm.c
ASoC: Fix prototype for nuc900_ac97_probe and nuc900_ac97_remove
ASoC: Fix compile error for nuc900-ac97.c
ALSA: hda: Use BIOS auto-parsing instead of existing model quirk for MEDION MD2
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lrg/asoc-2.6 into fix/asoc
|
|
|
|
Not all omap boards use kernel based pin multiplexing so
CONFIG_SND_OMAP_SOC_N810 should not select it by default as it can make
harm to other boards in multi-board kernels.
Therefore put CONFIG_OMAP_MUX as a dependency to N810 ASoC machine driver.
Thanks to Tony Lindgren <tony@atomide.com> for noticing.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
BugLink: https://launchpad.net/bugs/683695
The original reporter states that headphone jacks do not appear to
work. Upon inspecting his codec dump, and upon further testing, it is
confirmed that the "alienware" model quirk is correct.
Reported-and-tested-by: Cody Thierauf
Cc: <stable@kernel.org> [2.6.32+]
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
According to the datasheet the bypass path enable/disable is
bit 3 therefore we need 0x8 and not 0x4.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Add support for the RME HDSP RPM IO box. Changes have been made in the identification of the IO box and the neccessary controls have been added.
Signed-off-by: Florian Faber <faberman@linuxproaudio.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When the s6105-ipcam ASoC driver had been converted to the
multi-component API, a single reference to a former structure
element remained, blocking successful compilation.
Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
s6000_soc_platform has lost its forward declaration and there no
longer is a name element in it, so use a string constant when
calling request_irq.
Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
A semicolon was missing.
Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
In nuc900_dma_hw_params(), if snd_pcm_lib_malloc_pages failed
it returns without calling spin_unlock_irqrestore().
Since snd_pcm_lib_malloc_pages() does not touch struct nuc900_audio,
we don't need to hold the lock while calling snd_pcm_lib_malloc_pages().
Fix it by moving spin_lock_irqsave() down to after snd_pcm_lib_malloc_pages().
In nuc900_dma_prepare(), spin_unlock_irqrestore() is missing in the error path.
Fix it by removing the return in default case.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
In OSS emulation, SNDCTL_DSP_RESET ioctl needs the reset of the internal
buffer state in addition to drop of the running streams. Otherwise the
succeeding access becomes inconsistent.
Tested-by: Amit Nagal <helloin.amit@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Otherwise, calling dev_get_drvdata in p1022_ds_remove returns NULL.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Otherwise, calling dev_get_drvdata in mpc8610_hpcd_remove returns NULL.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
nuc900_checkready
I think this unneededd !! operations just reduce the readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
This patch fixes below error:
CC sound/soc/nuc900/nuc900-pcm.o
sound/soc/nuc900/nuc900-pcm.c: In function 'nuc900_dma_open':
sound/soc/nuc900/nuc900-pcm.c:267: error: 'nuc900_ac97_data' undeclared (first use in this function)
sound/soc/nuc900/nuc900-pcm.c:267: error: (Each undeclared identifier is reported only once
sound/soc/nuc900/nuc900-pcm.c:267: error: for each function it appears in.)
sound/soc/nuc900/nuc900-pcm.c: At top level:
sound/soc/nuc900/nuc900-pcm.c:337: error: expected ',' or ';' before 'static'
sound/soc/nuc900/nuc900-pcm.c:354: error: 'nuc900_soc_platform_probe' undeclared here (not in a function)
make[3]: *** [sound/soc/nuc900/nuc900-pcm.o] Error 1
make[2]: *** [sound/soc/nuc900] Error 2
make[1]: *** [sound/soc] Error 2
make: *** [sound] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
This patch fixes below compile warning:
CC sound/soc/nuc900/nuc900-ac97.o
sound/soc/nuc900/nuc900-ac97.c:300: warning: initialization from incompatible pointer type
sound/soc/nuc900/nuc900-ac97.c:301: warning: initialization from incompatible pointer type
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|