| Age | Commit message (Collapse) | Author |
|---|
|
I have a Soundblaster 16PCI. For many years, alsa has had a bug where
not all of the card's controls are detected (many alsa versions,
many kernel versions). In particular, Master Playback Volume is
usually not detected, and so I get no sound or extremely faint sound.
The problem has always been inconsistent: sometimes all of the controls
are detected correctly, and sometimes a partial set is detected. It works
correctly about 10% of the time.
Finally, I got around to tracking down the problem. When the driver
fails, it prints the kernel message "AC'97 0 analog subsections not
ready". This message is generated from the function snd_ac97_mixer()
in ac97_codec.c. The message indicates that the card failed to come
back after reset within the time limit. The time limit is
120 milliseconds.
I tried increasing the time limit to 1 second, and found that this
made the driver work about 70% of the time. I tried increasing it
to 5 seconds, and it now seems to work 100% of the time.
I expect that this change would be completely harmless for
existing cards that work, and would only introduce additional
delay for cards that do not work.
ALSA bug#4032.
Signed-off-by: Steve Soule <sts11dbxr@gmail.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Overwrite pin config on intel DG45ID board.
intelhdmi - dont power off HDA link
ALSA: hrtimer - Fix lock-up
ALSA: intelhdmi - add channel mapping for typical configurations
ALSA: intelhdmi - channel mapping applies to Pin
ALSA: intelhdmi - accept DisplayPort pin
ALSA: hda - show HBR(High Bit Rate) pin cap in procfs
ALSA: hda - Fix LED GPIO setup for HP laptops with IDT codecs
ASoC: Fix build of OMAP sound drivers
ALSA: opti93x: fix irq releasing if the irq cannot be allocated
|
|
|
|
|
|
The pin config provided by BIOS have some problems:
0x0221401f: [Jack] HP Out at Ext Front <-- other association and sequence
0x02a19020: [Jack] Mic at Ext Front <-- other association
0x01113014: [Jack] Speaker at Ext Rear <-- line out (not speaker)
0x01114010: [Jack] Speaker at Ext Rear <-- line out
0x01a19030: [Jack] Mic at Ext Rear <-- other association
0x01111012: [Jack] Speaker at Ext Rear <-- line out
0x01116011: [Jack] Speaker at Ext Rear <-- line out
0x40f000f0: [N/A] Other at Ext N/A
0x40f000f0: [N/A] Other at Ext N/A
0x40f000f0: [N/A] Other at Ext N/A
0x40f000f0: [N/A] Other at Ext N/A
0x40f000f0: [N/A] Other at Ext N/A
0x01451140: [Jack] SPDIF Out at Ext Rear
0x40f000f0: [N/A] Other at Ext N/A
just overwrite it.
Signed-off-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
For codecs without EPSS support (G45/IbexPeak), the hotplug event will
be lost if the HDA is powered off during the time. After that the pin
presence detection verb returns inaccurate info.
So always power-on HDA link for !EPSS codecs.
KarL offers the fact and Takashi recommends to flag hda_bus. Thanks!
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The timer stop callback can be called from snd_timer_interrupt(), which
is called from the hrtimer callback. Since hrtimer_cancel() waits for
the callback completion, this eventually results in a lock-up.
This patch fixes the problem by just toggling a flag at stop callback
and call hrtimer_cancel() later.
Reported-and-tested-by: Wojtek Zabolotny <W.Zabolotny@elka.pw.edu.pl>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
IbexPeak is the first Intel HDMI audio codec to support channel mapping.
Currently the outstanding problem is, the HDMI channel order do not
agree with that of ALSA. This patch presents workaround for some
typical use cases. It gives priority to the typical ALSA surround
configurations, and defines channel mapping for them.
We may need better kernel+userspace interactive channel mapping scheme.
For example, in current scheme if user plays with the surround50 device,
the kernel is unaware of this and will still select the surround41
channel allocation and channel mapping..
Thanks to Marcin for offering good tips!
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
HDA036-A specifies that the Audio Sample Packet (ASP) Channel Mapping
verbs apply to Digital Display Pin Complex instead of Converter.
With this fix, channel mapping is working as expected for IbexPeak.
Thanks to Marcin for pointing this out!
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
HDA036 spec states:
DP (Display Port) indicates whether the Pin Complex Widget supports
connection to a Display Port sink. Supported if set to 1. Note that
it is possible for the pin widget to support more than one digital
display connection type, e.g. HDMI and DP bit are both set to 1.
Also export the DP pin cap in procfs.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Note that the HBR capability only applies to HDMI pin.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch fixes an error in processing of the HP BIOS configuration to enable
GPIO based mute LED indicator control. That error causes driver to enable
such control on all HP systems with the 92HD75 IDT codecs and results in
unnecessary toggling of the GPIO on mute control manipulation.
It also adds support of the future HP BIOS configuration extension for the
named control. New configuration string has a format HP_Mute_LED_P_G
where P can be 0 or 1 and defines mute LED GPIO control state (low/high)
that corresponds to the NOT muted state of the master volume
and G is the index of the GPIO to use (0..9)
Lastly, it adds more systems to the support of the audio implementation
as found on HP B-series systems
Signed-off-by: Vitaliy Kulikov <Vitaliy.Kulikov@idt.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
There are build errors when building for some of the omap2/3 boards without
enabling sound:
sound/built-in.o:(.data+0x43bc): undefined reference to `soc_codec_dev_tlv320aic23'
sound/built-in.o:(.data+0x43cc): undefined reference to `tlv320aic23_dai'
Confused me quite a bit since the drivers that had references to the
codec weren't enabled. Turns out the Makefile was using the wrong
config option to enable them. Patch below.
Reported-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
While Linux provided an O_SYNC flag basically since day 1, it took until
Linux 2.4.0-test12pre2 to actually get it implemented for filesystems,
since that day we had generic_osync_around with only minor changes and the
great "For now, when the user asks for O_SYNC, we'll actually give
O_DSYNC" comment. This patch intends to actually give us real O_SYNC
semantics in addition to the O_DSYNC semantics. After Jan's O_SYNC
patches which are required before this patch it's actually surprisingly
simple, we just need to figure out when to set the datasync flag to
vfs_fsync_range and when not.
This patch renames the existing O_SYNC flag to O_DSYNC while keeping it's
numerical value to keep binary compatibility, and adds a new real O_SYNC
flag. To guarantee backwards compatiblity it is defined as expanding to
both the O_DSYNC and the new additional binary flag (__O_SYNC) to make
sure we are backwards-compatible when compiled against the new headers.
This also means that all places that don't care about the differences can
just check O_DSYNC and get the right behaviour for O_SYNC, too - only
places that actuall care need to check __O_SYNC in addition. Drivers and
network filesystems have been updated in a fail safe way to always do the
full sync magic if O_DSYNC is set. The few places setting O_SYNC for
lower layers are kept that way for now to stay failsafe.
We enforce that O_DSYNC is set when __O_SYNC is set early in the open path
to make sure we always get these sane options.
Note that parisc really screwed up their headers as they already define a
O_DSYNC that has always been a no-op. We try to repair it by using it for
the new O_DSYNC and redefinining O_SYNC to send both the traditional
O_SYNC numerical value _and_ the O_DSYNC one.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andreas Dilger <adilger@sun.com>
Acked-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Use the chip->irq to check if the irq should be released so the irq is not released
if it has not been allocated.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: ice1724 - aureon - modify WM8770 Master & DAC volume
ALSA: hda/realtek: quirk for D945GCLF2 mainboard
ALSA: hda - Terradici HDA controllers does not support 64-bit mode
ALSA: document: Add direct git link to grub hda-analyzer
ALSA: radio/sound/miro: fix build, cleanup depends/selects
ALSA: hda - Generalize EAPD inversion check in patch_analog.c
ASoC: Wrong variable returned on error
ALSA: snd-usb-us122l: add product IDs of US-122MKII and US-144MKII
ALSA: hda - Exclude unusable ADCs for ALC88x
ALSA: hda - Add missing Line-Out and PCM switches as slave
ALSA: hda - iMac 9,1 sound patch.
ALSA: opti93x: set MC indirect registers base from PnP data
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (42 commits)
tree-wide: fix misspelling of "definition" in comments
reiserfs: fix misspelling of "journaled"
doc: Fix a typo in slub.txt.
inotify: remove superfluous return code check
hdlc: spelling fix in find_pvc() comment
doc: fix regulator docs cut-and-pasteism
mtd: Fix comment in Kconfig
doc: Fix IRQ chip docs
tree-wide: fix assorted typos all over the place
drivers/ata/libata-sff.c: comment spelling fixes
fix typos/grammos in Documentation/edac.txt
sysctl: add missing comments
fs/debugfs/inode.c: fix comment typos
sgivwfb: Make use of ARRAY_SIZE.
sky2: fix sky2_link_down copy/paste comment error
tree-wide: fix typos "couter" -> "counter"
tree-wide: fix typos "offest" -> "offset"
fix kerneldoc for set_irq_msi()
spidev: fix double "of of" in comment
comment typo fix: sybsystem -> subsystem
...
|
|
|
|
|
|
The volume levels in original implementation are incorrect and does
not match the dB scale. The real range is linear (in the sense of
the dB scale) from 0dB to -100dB. Remove logaritmic table and make
all volumes from range 0dB..100dB.
The tests are in RedHat's bugzilla #540817.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Quirk for the ALC662 found on the Intel D945GCLF2 (and possibly other)
mainboards.
Signed-off-by: David Santinoli <david@santinoli.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Confirmed from vendor and tests in RedHat bugzilla #536782 .
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add a flag to spec field so that the EAPD inversion can be checked
outside the relevant control callbacks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (149 commits)
arm: omap: Add omap3_defconfig
AM35xx: Defconfig for AM3517 EVM board
AM35xx: Add support for AM3517 EVM board
omap: 3630sdp: defconfig creation
omap: 3630sdp: introduce 3630 sdp board support
omap3: Add defconfig for IGEP v2 board
omap3: Add minimal IGEP v2 support
omap3: Add CompuLab CM-T35 defconfig
omap3: Add CompuLab CM-T35 board support
omap3: rx51: Add wl1251 wlan driver support
omap3: rx51: Add SDRAM init
omap1: Add default kernel configuration for Herald
omap1: Add board support and LCD for HTC Herald
omap: zoom2: update defconfig for LL_DEBUG_NONE
omap: zoom3: defconfig creation
omap3: zoom: Introduce zoom3 board support
omap3: zoom: Drop i2c-1 speed to 2400
omap3: zoom: rename zoom2 name to generic zoom
omap3: zoom: split board file for software reuse
omap3evm: MIgrate to smsc911x ethernet driver
...
Fix trivial conflict (two unrelated config options added next to each
other) in arch/arm/mach-omap2/Makefile
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (294 commits)
S3C64XX: Staticise platform data for PCM devices
ASoC: Rename controls with a / in wm_hubs
snd-fm801: autodetect SF64-PCR (tuner-only) card
ALSA: tea575x-tuner: fix mute
ASoC: au1x: dbdma2: plug memleak in pcm device creation error path
ASoC: au1x: dbdma2: fix oops on soc device removal.
ALSA: hda - Fix memory leaks in the previous patch
ALSA: hda - Add ALC661/259, ALC892/888VD support
ALSA: opti9xx: remove snd_opti9xx fields
ALSA: aaci - Clean up duplicate code
ALSA: usb - Fix mixer map for Hercules Gamesurround Muse Pocket LT
ALSA: hda - Add position_fix quirk for HP dv3
ALSA: hda - Add a pin-fix for FSC Amilo Pi1505
ALSA: hda - Fix Cxt5047 test mode
ASoC: pxa/raumfeld: adopt new snd_soc_dai_set_pll() API
ASoC: sh: fsi: Add runtime PM support
sh: ms7724se: Add runtime PM support for FSI
ALSA: hda - Add a position_fix quirk for MSI Wind U115
ALSA: opti-miro: add PnP detection
ALSA: opti-miro: separate comon probing code
...
|
|
The wrong variable was returned in the case of an error
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
I added the product IDs of the new revisions of the devices, so owners
can test whether this suffices to make them work. Patched against ALSA
snapshot 20091207.
Signed-off-by: Tobias Hansen <Tobias.Hansen at physik.uni-hamburg.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
On Realtek codecs, a digital mic pin is connected often only to a single
ADC. But the parser tries to set up all ADCs no matter whether the
digital mic is available, and results in non-selectable input source.
This patch adds a check of input-source availability of each ADC, and
excludes ones that don't support all input sources.
Reference: Novell bnc#561235
http://bugzilla.novell.com/show_bug.cgi?id=561235
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Realtek codecs may have "PCM" and "Line-Out" playback switches, and
they can be slaves for vmaster.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This is an updated patch for the Apple iMac 9,1 model to add sound.
Original patch posted here:
http://article.gmane.org/gmane.linux.alsa.devel/61361/match=
I have been using this patch for a while now
and have to say it works vary well, except for a few minor
things:
With the iMac 24-inch 3.06GHz Intel Core 2 Duo
everything seems to be working as it should,
although I have not looked into the microphone
(never really use one, nor have any apps to test,
my guess is it doesn't work, or I never figured out how
to get it to work).
With the iMac 24-inch 2.66GHz Intel Core 2 Duo
everything is the same as with the above machine
except I'm hearing a light scratchy/distortion noise
come out of the speakers when using headphones(above machine
does not do this).
Other than that the sound level is great(especially with good Dj headphones).
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Tested-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The PnP data on the OPTI931 and OPTI933 contains io port
range for the MC indirect registers. Use the PnP range
instead of hardwired value 0xE0E.
Also, request region of MC indirect registers so it is
marked as used to other drivers (this was missing previously).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Conflicts:
kernel/irq/chip.c
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6: (50 commits)
pcmcia: rework the irq_req_t typedef
pcmcia: remove deprecated handle_to_dev() macro
pcmcia: pcmcia_request_window() doesn't need a pointer to a pointer
pcmcia: remove unused "window_t" typedef
pcmcia: move some window-related code to pcmcia_ioctl.c
pcmcia: Change window_handle_t logic to unsigned long
pcmcia: Pass struct pcmcia_socket to pcmcia_get_mem_page()
pcmcia: Pass struct pcmcia_device to pcmcia_map_mem_page()
pcmcia: Pass struct pcmcia_device to pcmcia_release_window()
drivers/pcmcia: remove unnecessary kzalloc
pcmcia: correct handling for Zoomed Video registers in topic.h
pcmcia: fix printk formats
pcmcia: autoload module pcmcia
pcmcia/staging: update comedi drivers
PCMCIA: stop duplicating pci_irq in soc_pcmcia_socket
PCMCIA: ss: allow PCI IRQs > 255
PCMCIA: soc_common: remove 'dev' member from soc_pcmcia_socket
PCMCIA: soc_common: constify soc_pcmcia_socket ops member
PCMCIA: sa1111: remove duplicated initializers
PCMCIA: sa1111: wrap soc_pcmcia_socket to contain sa1111 specific data
...
|
|
|
|
|
|
|
|
|
|
That is "success", "unknown", "through", "performance", "[re|un]mapping"
, "access", "default", "reasonable", "[con]currently", "temperature"
, "channel", "[un]used", "application", "example","hierarchy", "therefore"
, "[over|under]flow", "contiguous", "threshold", "enough" and others.
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch was generated by
git grep -E -i -l 'couter' | xargs -r perl -p -i -e 's/couter/counter/'
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This renames from a character / to : of controls. A / occurs below error
messages.
ASoC: Failed to create IN2RP/VXRP debugfs file
ASoC: Failed to create IN2LP/VXRN debugfs file
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
When primary AC97 is not found, don't fail with tons of AC97 errors.
Assume that the card is SF64-PCR (tuner-only).
This makes the SF64-PCR radio card work "out of the box".
Also fixes a bug that can cause an oops here:
if (tea575x_tuner > 0 && (tea575x_tuner & 0x000f) < 4) {
when tea575x_tuner == 16, it passes this check and causes problems
a couple lines below:
chip->tea.ops = &snd_fm801_tea_ops[(tea575x_tuner & 0x000f) - 1];
Tested with SF64-PCR, but I don't have any of those sound or sound+radio cards
to test if I didn't break anything.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fix mute state reporting in tea575x-tuner.
This fixes mute function in kradio on SF64-PCR radio card.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
free the allocated pcm platform device in the error path.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
platform_device_unregister() frees resources for us, no need to
do it explicitly. Fixes an oops when machine code removes the
soc-audio device.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The previous hack for replacing the codec name give memory leaks at
error paths. This patch fixes them.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fixed List:
1. Add alc_read_coef_idx function
2. Add ALC661 ALC259
3. Add ALC892 ALC888VD
Signed-off-by: Kailang Yang <kailang@realtek.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Remove snd_opti9xx fields which are indirect arguments to
the snd_opti9xx_configure(). Pass these values as function
arguments.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Now snd_ac97_pcm_open() is called with the exactly same arguments
for both playback and capture directions. Remove the unneeded check.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Muse Pocket use brocken mixer names, so alsamixer and PA can't use it correctly
This patch add quirk to overwirte default mixers.
Signed-off-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
