diff options
author | Poonam Aggrwal <poonam.aggrwal@freescale.com> | 2011-02-09 19:17:53 (GMT) |
---|---|---|
committer | Kumar Gala <galak@kernel.crashing.org> | 2011-09-30 00:01:04 (GMT) |
commit | 49249e137daeec4d51c99aa69a8459d2f11cd94d (patch) | |
tree | 345c1a3def5e1d683e389fde489836b0f654e27e | |
parent | 14aa71e6603def3bf258d9d05f11fe8454a59e50 (diff) | |
download | u-boot-fsl-qoriq-49249e137daeec4d51c99aa69a8459d2f11cd94d.tar.xz |
powerpc/85xx: Add basic support for P1010RDB
Boot methods supported: NOR Flash, SPI Flash and SDCARD
This patch adds the following basic interfaces:
DDR3, eTSEC, DUART, I2C, SD/MMC, USB, SATA, PCIe, NOR Flash, SPI Flash.
P1010RDB Overview
-----------------
1Gbyte DDR3 (on board DDR)
Local Bus (IFC):
32Mbyte 16bit NOR flash
32Mbyte SLC NAND Flash
64KB CPLD device(GPCM interface)
SPI Flash:
128 Mbit SPI Flash memory
SD/MMC:
connector to interface with the SD memory card
SATA:
1 internal SATA connect to 2.5. 160G SATA2 HDD
1 eSATA connector to rear panel
USB 2.0:
x1 USB 2.0 port: connected via a UTMI PHY to Mini-AB interface.
x1 USB 2.0 port: directly connected to Mini-AB interface Ethernet
eTSEC:
eTSEC1: Connected to RGMII PHY VSC8641XKO
eTSEC2: Connected to SGMII PHY VSC8221
eTSEC3: Connected to SGMII PHY VSC8221
eCAN:
Two DB-9 female connectors for Field bus interface
UART:
supports two UARTs up to 115200 bps for console
TDM:
2 FXS ports connected via an external SLIC to the TDM interface.
SLIC:
SPI SLIC
I2C:
Serial EEprom
Real time clock
256 Kbit M24256 I2C EEPROM
PCIe:
PCIe and mPCIe connectors.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
-rw-r--r-- | board/freescale/p1010rdb/Makefile | 52 | ||||
-rw-r--r-- | board/freescale/p1010rdb/ddr.c | 250 | ||||
-rw-r--r-- | board/freescale/p1010rdb/law.c | 35 | ||||
-rw-r--r-- | board/freescale/p1010rdb/p1010rdb.c | 330 | ||||
-rw-r--r-- | board/freescale/p1010rdb/tlb.c | 98 | ||||
-rw-r--r-- | boards.cfg | 6 | ||||
-rw-r--r-- | include/configs/P1010RDB.h | 706 |
7 files changed, 1477 insertions, 0 deletions
diff --git a/board/freescale/p1010rdb/Makefile b/board/freescale/p1010rdb/Makefile new file mode 100644 index 0000000..1dcd490 --- /dev/null +++ b/board/freescale/p1010rdb/Makefile @@ -0,0 +1,52 @@ +# +# Copyright 2010-2011 Freescale Semiconductor, Inc. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS-y += $(BOARD).o +COBJS-y += ddr.o +COBJS-y += law.o +COBJS-y += tlb.o + +SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(call cmd_link_o_target, $(OBJS)) + +clean: + rm -f $(OBJS) $(SOBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/freescale/p1010rdb/ddr.c b/board/freescale/p1010rdb/ddr.c new file mode 100644 index 0000000..e5d8423 --- /dev/null +++ b/board/freescale/p1010rdb/ddr.c @@ -0,0 +1,250 @@ +/* + * Copyright 2010-2011 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/mmu.h> +#include <asm/immap_85xx.h> +#include <asm/processor.h> +#include <asm/fsl_ddr_sdram.h> +#include <asm/fsl_ddr_dimm_params.h> +#include <asm/io.h> +#include <asm/fsl_law.h> + +DECLARE_GLOBAL_DATA_PTR; + +#ifndef CONFIG_DDR_RAW_TIMING +#define CONFIG_SYS_DRAM_SIZE 1024 + +fsl_ddr_cfg_regs_t ddr_cfg_regs_800 = { + .cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS, + .cs[0].config = CONFIG_SYS_DDR_CS0_CONFIG, + .cs[0].config_2 = CONFIG_SYS_DDR_CS0_CONFIG_2, + .timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3_800, + .timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0_800, + .timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1_800, + .timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2_800, + .ddr_sdram_cfg = CONFIG_SYS_DDR_CONTROL, + .ddr_sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL_2, + .ddr_sdram_mode = CONFIG_SYS_DDR_MODE_1_800, + .ddr_sdram_mode_2 = CONFIG_SYS_DDR_MODE_2_800, + .ddr_sdram_md_cntl = CONFIG_SYS_DDR_MODE_CONTROL, + .ddr_sdram_interval = CONFIG_SYS_DDR_INTERVAL_800, + .ddr_data_init = CONFIG_MEM_INIT_VALUE, + .ddr_sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL_800, + .ddr_init_addr = CONFIG_SYS_DDR_INIT_ADDR, + .ddr_init_ext_addr = CONFIG_SYS_DDR_INIT_EXT_ADDR, + .timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4, + .timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5, + .ddr_zq_cntl = CONFIG_SYS_DDR_ZQ_CONTROL, + .ddr_wrlvl_cntl = CONFIG_SYS_DDR_WRLVL_CONTROL_800, + .ddr_sr_cntr = CONFIG_SYS_DDR_SR_CNTR, + .ddr_sdram_rcw_1 = CONFIG_SYS_DDR_RCW_1, + .ddr_sdram_rcw_2 = CONFIG_SYS_DDR_RCW_2 +}; + +fsl_ddr_cfg_regs_t ddr_cfg_regs_667 = { + .cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS, + .cs[0].config = CONFIG_SYS_DDR_CS0_CONFIG, + .cs[0].config_2 = CONFIG_SYS_DDR_CS0_CONFIG_2, + .timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3_667, + .timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0_667, + .timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1_667, + .timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2_667, + .ddr_sdram_cfg = CONFIG_SYS_DDR_CONTROL, + .ddr_sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL_2, + .ddr_sdram_mode = CONFIG_SYS_DDR_MODE_1_667, + .ddr_sdram_mode_2 = CONFIG_SYS_DDR_MODE_2_667, + .ddr_sdram_md_cntl = CONFIG_SYS_DDR_MODE_CONTROL, + .ddr_sdram_interval = CONFIG_SYS_DDR_INTERVAL_667, + .ddr_data_init = CONFIG_MEM_INIT_VALUE, + .ddr_sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL_667, + .ddr_init_addr = CONFIG_SYS_DDR_INIT_ADDR, + .ddr_init_ext_addr = CONFIG_SYS_DDR_INIT_EXT_ADDR, + .timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4, + .timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5, + .ddr_zq_cntl = CONFIG_SYS_DDR_ZQ_CONTROL, + .ddr_wrlvl_cntl = CONFIG_SYS_DDR_WRLVL_CONTROL_667, + .ddr_sr_cntr = CONFIG_SYS_DDR_SR_CNTR, + .ddr_sdram_rcw_1 = CONFIG_SYS_DDR_RCW_1, + .ddr_sdram_rcw_2 = CONFIG_SYS_DDR_RCW_2 +}; + +fixed_ddr_parm_t fixed_ddr_parm_0[] = { + {750, 850, &ddr_cfg_regs_800}, + {607, 749, &ddr_cfg_regs_667}, + {0, 0, NULL} +}; + +unsigned long get_sdram_size(void) +{ + struct cpu_type *cpu; + phys_size_t ddr_size; + + cpu = gd->cpu; + /* P1014 and it's derivatives support max 16it DDR width */ + if (cpu->soc_ver == SVR_P1014 || cpu->soc_ver == SVR_P1014_E) + ddr_size = (CONFIG_SYS_DRAM_SIZE / 2); + else + ddr_size = CONFIG_SYS_DRAM_SIZE; + + return ddr_size; +} + +/* + * Fixed sdram init -- doesn't use serial presence detect. + */ +phys_size_t fixed_sdram(void) +{ + int i; + char buf[32]; + fsl_ddr_cfg_regs_t ddr_cfg_regs; + phys_size_t ddr_size; + ulong ddr_freq, ddr_freq_mhz; + struct cpu_type *cpu; + +#if defined(CONFIG_SYS_RAMBOOT) + return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024; +#endif + + ddr_freq = get_ddr_freq(0); + ddr_freq_mhz = ddr_freq / 1000000; + + printf("Configuring DDR for %s MT/s data rate\n", + strmhz(buf, ddr_freq)); + + for (i = 0; fixed_ddr_parm_0[i].max_freq > 0; i++) { + if ((ddr_freq_mhz > fixed_ddr_parm_0[i].min_freq) && + (ddr_freq_mhz <= fixed_ddr_parm_0[i].max_freq)) { + memcpy(&ddr_cfg_regs, fixed_ddr_parm_0[i].ddr_settings, + sizeof(ddr_cfg_regs)); + break; + } + } + + if (fixed_ddr_parm_0[i].max_freq == 0) + panic("Unsupported DDR data rate %s MT/s data rate\n", + strmhz(buf, ddr_freq)); + + cpu = gd->cpu; + /* P1014 and it's derivatives support max 16bit DDR width */ + if (cpu->soc_ver == SVR_P1014 || cpu->soc_ver == SVR_P1014_E) { + ddr_cfg_regs.ddr_sdram_cfg |= SDRAM_CFG_16_BE; + ddr_cfg_regs.cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS >> 1; + ddr_cfg_regs.ddr_sdram_cfg &= ~0x00180000; + ddr_cfg_regs.ddr_sdram_cfg |= 0x001080000; + } + + ddr_size = (phys_size_t) CONFIG_SYS_SDRAM_SIZE * 1024 * 1024; + fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0); + + if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE, ddr_size, + LAW_TRGT_IF_DDR_1) < 0) { + printf("ERROR setting Local Access Windows for DDR\n"); + return 0; + } + + return ddr_size; +} + +#else /* CONFIG_DDR_RAW_TIMING */ +/* + * Samsung K4B2G0846C-HCF8 + * The following timing are for "downshift" + * i.e. to use CL9 part as CL7 + * otherwise, tAA, tRCD, tRP will be 13500ps + * and tRC will be 49500ps + */ +dimm_params_t ddr_raw_timing = { + .n_ranks = 1, + .rank_density = 1073741824u, + .capacity = 1073741824u, + .primary_sdram_width = 32, + .ec_sdram_width = 0, + .registered_dimm = 0, + .mirrored_dimm = 0, + .n_row_addr = 15, + .n_col_addr = 10, + .n_banks_per_sdram_device = 8, + .edc_config = 0, + .burst_lengths_bitmask = 0x0c, + + .tCKmin_X_ps = 1875, + .caslat_X = 0x1e << 4, /* 5,6,7,8 */ + .tAA_ps = 13125, + .tWR_ps = 15000, + .tRCD_ps = 13125, + .tRRD_ps = 7500, + .tRP_ps = 13125, + .tRAS_ps = 37500, + .tRC_ps = 50625, + .tRFC_ps = 160000, + .tWTR_ps = 7500, + .tRTP_ps = 7500, + .refresh_rate_ps = 7800000, + .tFAW_ps = 37500, +}; + +int fsl_ddr_get_dimm_params(dimm_params_t *pdimm, + unsigned int controller_number, + unsigned int dimm_number) +{ + const char dimm_model[] = "Fixed DDR on board"; + + if ((controller_number == 0) && (dimm_number == 0)) { + memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t)); + memset(pdimm->mpart, 0, sizeof(pdimm->mpart)); + memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1); + } + + return 0; +} + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + struct cpu_type *cpu; + int i; + popts->clk_adjust = 6; + popts->cpo_override = 0x1f; + popts->write_data_delay = 2; + popts->half_strength_driver_enable = 1; + /* Write leveling override */ + popts->wrlvl_en = 1; + popts->wrlvl_override = 1; + popts->wrlvl_sample = 0xf; + popts->wrlvl_start = 0x8; + popts->trwt_override = 1; + popts->trwt = 0; + + cpu = gd->cpu; + /* P1014 and it's derivatives support max 16it DDR width */ + if (cpu->soc_ver == SVR_P1014 || cpu->soc_ver == SVR_P1014_E) + popts->data_bus_width = DDR_DATA_BUS_WIDTH_16; + + for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { + popts->cs_local_opts[i].odt_rd_cfg = FSL_DDR_ODT_NEVER; + popts->cs_local_opts[i].odt_wr_cfg = FSL_DDR_ODT_CS; + } +} + +#endif /* CONFIG_DDR_RAW_TIMING */ diff --git a/board/freescale/p1010rdb/law.c b/board/freescale/p1010rdb/law.c new file mode 100644 index 0000000..3ed77fc --- /dev/null +++ b/board/freescale/p1010rdb/law.c @@ -0,0 +1,35 @@ +/* + * Copyright 2010-2011 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/fsl_law.h> +#include <asm/mmu.h> + +struct law_entry law_table[] = { +#ifndef CONFIG_SDCARD + SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_IFC), + SET_LAW(CONFIG_SYS_CPLD_BASE_PHYS, LAW_SIZE_128K, LAW_TRGT_IF_IFC), + SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_IFC), +#endif +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/p1010rdb/p1010rdb.c b/board/freescale/p1010rdb/p1010rdb.c new file mode 100644 index 0000000..03e9da1 --- /dev/null +++ b/board/freescale/p1010rdb/p1010rdb.c @@ -0,0 +1,330 @@ +/* + * Copyright 2010-2011 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/processor.h> +#include <asm/mmu.h> +#include <asm/cache.h> +#include <asm/immap_85xx.h> +#include <asm/io.h> +#include <miiphy.h> +#include <libfdt.h> +#include <fdt_support.h> +#include <fsl_mdio.h> +#include <tsec.h> +#include <mmc.h> +#include <netdev.h> +#include <pci.h> +#include <asm/fsl_serdes.h> +#include <asm/fsl_ifc.h> +#include <asm/fsl_pci.h> + +#ifndef CONFIG_SDCARD +#include <hwconfig.h> +#endif + +DECLARE_GLOBAL_DATA_PTR; + +#define GPIO4_PCIE_RESET_SET 0x08000000 +#define MUX_CPLD_CAN_UART 0x00 +#define MUX_CPLD_TDM 0x01 +#define MUX_CPLD_SPICS0_FLASH 0x00 +#define MUX_CPLD_SPICS0_SLIC 0x02 + +#ifndef CONFIG_SDCARD +struct cpld_data { + u8 cpld_ver; /* cpld revision */ + u8 pcba_ver; /* pcb revision number */ + u8 twindie_ddr3; + u8 res1[6]; + u8 bank_sel; /* NOR Flash bank */ + u8 res2[5]; + u8 usb2_sel; + u8 res3[1]; + u8 porsw_sel; + u8 tdm_can_sel; + u8 spi_cs0_sel; /* SPI CS0 SLIC/SPI Flash */ + u8 por0; /* POR Options */ + u8 por1; /* POR Options */ + u8 por2; /* POR Options */ + u8 por3; /* POR Options */ +}; + +void cpld_show(void) +{ + struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); + + printf("CPLD: V%x.%x PCBA: V%x.0\n", + in_8(&cpld_data->cpld_ver) & 0xF0, + in_8(&cpld_data->cpld_ver) & 0x0F, + in_8(&cpld_data->pcba_ver) & 0x0F); + +#ifdef CONFIG_DEBUG + printf("twindie_ddr =%x\n", + in_8(&cpld_data->twindie_ddr3)); + printf("bank_sel =%x\n", + in_8(&cpld_data->bank_sel)); + printf("usb2_sel =%x\n", + in_8(&cpld_data->usb2_sel)); + printf("porsw_sel =%x\n", + in_8(&cpld_data->porsw_sel)); + printf("tdm_can_sel =%x\n", + in_8(&cpld_data->tdm_can_sel)); + printf("tdm_can_sel =%x\n", + in_8(&cpld_data->tdm_can_sel)); + printf("spi_cs0_sel =%x\n", + in_8(&cpld_data->spi_cs0_sel)); + printf("bcsr0 =%x\n", + in_8(&cpld_data->bcsr0)); + printf("bcsr1 =%x\n", + in_8(&cpld_data->bcsr1)); + printf("bcsr2 =%x\n", + in_8(&cpld_data->bcsr2)); + printf("bcsr3 =%x\n", + in_8(&cpld_data->bcsr3)); +#endif +} +#endif + +int board_early_init_f(void) +{ + ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR); +#ifndef CONFIG_SDCARD + struct fsl_ifc *ifc = (void *)CONFIG_SYS_IFC_ADDR; + + /* Clock configuration to access CPLD using IFC(GPCM) */ + setbits_be32(&ifc->ifc_gcr, 1 << IFC_GCR_TBCTL_TRN_TIME_SHIFT); +#endif + /* + * Reset PCIe slots via GPIO4 + */ + setbits_be32(&pgpio->gpdir, GPIO4_PCIE_RESET_SET); + setbits_be32(&pgpio->gpdat, GPIO4_PCIE_RESET_SET); + + return 0; +} + +int board_early_init_r(void) +{ +#ifndef CONFIG_SDCARD + const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; + const u8 flash_esel = find_tlb_idx((void *)flashbase, 1); + + /* + * Remap Boot flash region to caching-inhibited + * so that flash can be erased properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + /* invalidate existing TLB entry for flash */ + disable_tlb(flash_esel); + + set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, flash_esel, BOOKE_PAGESZ_16M, 1); + + set_tlb(1, flashbase + 0x1000000, + CONFIG_SYS_FLASH_BASE_PHYS + 0x1000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, flash_esel+1, BOOKE_PAGESZ_16M, 1); +#endif + return 0; +} + +#ifdef CONFIG_PCI +void pci_init_board(void) +{ + fsl_pcie_init_board(0); +} +#endif /* ifdef CONFIG_PCI */ + +int checkboard(void) +{ + struct cpu_type *cpu; + + cpu = gd->cpu; + printf("Board: %sRDB ", cpu->name); +#ifdef CONFIG_PHYS_64BIT + puts("(36-bit addrmap)"); +#endif + puts("\n"); + + return 0; +} + +#ifdef CONFIG_TSEC_ENET +int board_eth_init(bd_t *bis) +{ + struct fsl_pq_mdio_info mdio_info; + struct tsec_info_struct tsec_info[4]; + struct cpu_type *cpu; + int num = 0; + + cpu = gd->cpu; + +#ifdef CONFIG_TSEC1 + SET_STD_TSEC_INFO(tsec_info[num], 1); + num++; +#endif +#ifdef CONFIG_TSEC2 + SET_STD_TSEC_INFO(tsec_info[num], 2); + num++; +#endif +#ifdef CONFIG_TSEC3 + /* P1014 and it's derivatives do not support eTSEC3 */ + if (cpu->soc_ver != SVR_P1014 && cpu->soc_ver != SVR_P1014_E) { + SET_STD_TSEC_INFO(tsec_info[num], 3); + num++; + } +#endif + if (!num) { + printf("No TSECs initialized\n"); + return 0; + } + + mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR; + mdio_info.name = DEFAULT_MII_NAME; + + fsl_pq_mdio_init(bis, &mdio_info); + + tsec_eth_init(bis, tsec_info, num); + + return pci_eth_init(bis); +} +#endif + +#if defined(CONFIG_OF_BOARD_SETUP) +void fdt_del_flexcan(void *blob) +{ + int nodeoff = 0; + + while ((nodeoff = fdt_node_offset_by_compatible(blob, 0, + "fsl,flexcan-v1.0")) >= 0) { + fdt_del_node(blob, nodeoff); + } +} + +void fdt_del_spi_flash(void *blob) +{ + int nodeoff = 0; + + while ((nodeoff = fdt_node_offset_by_compatible(blob, 0, + "spansion,s25sl12801")) >= 0) { + fdt_del_node(blob, nodeoff); + } +} + +void fdt_del_spi_slic(void *blob) +{ + int nodeoff = 0; + + while ((nodeoff = fdt_node_offset_by_compatible(blob, 0, + "zarlink,le88266")) >= 0) { + fdt_del_node(blob, nodeoff); + } +} + +void fdt_del_tdm(void *blob) +{ + int nodeoff = 0; + + while ((nodeoff = fdt_node_offset_by_compatible(blob, 0, + "fsl,starlite-tdm")) >= 0) { + fdt_del_node(blob, nodeoff); + } +} + +void ft_board_setup(void *blob, bd_t *bd) +{ + phys_addr_t base; + phys_size_t size; + struct cpu_type *cpu; + + cpu = gd->cpu; + + ft_cpu_setup(blob, bd); + + base = getenv_bootm_low(); + size = getenv_bootm_size(); + +#if defined(CONFIG_PCI) + FT_FSL_PCI_SETUP; +#endif + + fdt_fixup_memory(blob, (u64)base, (u64)size); + + fdt_fixup_dr_usb(blob, bd); + + /* P1014 and it's derivatives don't support CAN and eTSEC3 */ + if (cpu->soc_ver == SVR_P1014 || cpu->soc_ver == SVR_P1014_E) { + fdt_del_flexcan(blob); + fdt_del_node_and_alias(blob, "ethernet2"); + } +#ifndef CONFIG_SDCARD + if (hwconfig_subarg_cmp("fsl_p1010mux", "tdm_can", "can")) { + printf("fdt CAN"); + fdt_del_tdm(blob); + fdt_del_spi_slic(blob); + } +#ifndef CONFIG_SPIFLASH + else if (hwconfig_subarg_cmp("fsl_p1010mux", "tdm_can", "tdm")) { + printf("fdt TDM"); + fdt_del_flexcan(blob); + fdt_del_spi_flash(blob); + } +#endif +#endif +} +#endif + +#ifndef CONFIG_SDCARD +int misc_init_r(void) +{ + struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + + if (hwconfig_subarg_cmp("fsl_p1010mux", "tdm_can", "can")) { + clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_CAN1_TDM | + MPC85xx_PMUXCR_CAN1_UART | + MPC85xx_PMUXCR_CAN2_TDM | + MPC85xx_PMUXCR_CAN2_UART); + out_8(&cpld_data->tdm_can_sel, MUX_CPLD_CAN_UART); + } +#ifndef CONFIG_SPIFLASH + if (hwconfig_subarg_cmp("fsl_p1010mux", "tdm_can", "tdm")) { + printf("TDM"); + clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_CAN2_UART | + MPC85xx_PMUXCR_CAN1_UART); + setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_CAN2_TDM | + MPC85xx_PMUXCR_CAN1_TDM); + clrbits_be32(&gur->pmuxcr2, MPC85xx_PMUXCR2_UART_GPIO); + setbits_be32(&gur->pmuxcr2, MPC85xx_PMUXCR2_UART_TDM); + out_8(&cpld_data->tdm_can_sel, MUX_CPLD_TDM); + out_8(&cpld_data->spi_cs0_sel, MUX_CPLD_SPICS0_SLIC); + } +#endif + return 0; +} +#endif diff --git a/board/freescale/p1010rdb/tlb.c b/board/freescale/p1010rdb/tlb.c new file mode 100644 index 0000000..4256bf4 --- /dev/null +++ b/board/freescale/p1010rdb/tlb.c @@ -0,0 +1,98 @@ +/* + * Copyright 2010-2011 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/mmu.h> + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024 , + CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024 , + CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024 , + CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* TLB 1 */ + /* *I*** - Covers boot page */ + SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_4K, 1), + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_1M, 1), + +#ifndef CONFIG_NAND_SPL +#ifndef CONFIG_SDCARD + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, + 0, 2, BOOKE_PAGESZ_16M, 1), + + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE + 0x1000000, + CONFIG_SYS_FLASH_BASE_PHYS + 0x1000000, + MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, + 0, 3, BOOKE_PAGESZ_16M, 1), +#endif + +#ifdef CONFIG_PCI + /* *I*G* - PCI */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_1G, 1), + + /* *I*G* - PCI I/O */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 5, BOOKE_PAGESZ_256K, 1), +#endif +#endif + +#ifndef CONFIG_SDCARD + /* *I*G - Board CPLD */ + SET_TLB_ENTRY(1, CONFIG_SYS_CPLD_BASE, CONFIG_SYS_CPLD_BASE_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 6, BOOKE_PAGESZ_256K, 1), + + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 7, BOOKE_PAGESZ_1M, 1), +#endif + +#if defined(CONFIG_SYS_RAMBOOT) + SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 8, BOOKE_PAGESZ_1G, 1) +#endif +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); @@ -567,6 +567,12 @@ MPC8569MDS_NAND powerpc mpc85xx mpc8569mds freesca MPC8572DS powerpc mpc85xx mpc8572ds freescale - MPC8572DS MPC8572DS_36BIT powerpc mpc85xx mpc8572ds freescale - MPC8572DS:36BIT MPC8572DS_NAND powerpc mpc85xx mpc8572ds freescale - MPC8572DS:NAND +P1010RDB_NOR powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB +P1010RDB_36BIT_NOR powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB,36BIT +P1010RDB_SDCARD powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB,SDCARD +P1010RDB_SPIFLASH powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB,SPIFLASH +P1010RDB_36BIT_SDCARD powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB,36BIT,SDCARD +P1010RDB_36BIT_SPIFLASH powerpc mpc85xx p1010rdb freescale - P1010RDB:P1010RDB,36BIT,SPIFLASH P1011RDB powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P1011RDB P1011RDB_36BIT powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P1011RDB,36BIT P1011RDB_36BIT_SDCARD powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P1011RDB,36BIT,SDCARD diff --git a/include/configs/P1010RDB.h b/include/configs/P1010RDB.h new file mode 100644 index 0000000..3304ea3 --- /dev/null +++ b/include/configs/P1010RDB.h @@ -0,0 +1,706 @@ +/* + * Copyright 2010-2011 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * P010 RDB board configuration file + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#ifdef CONFIG_36BIT +#define CONFIG_PHYS_64BIT +#endif + +#ifdef CONFIG_P1010RDB +#define CONFIG_P1010 +#endif + +#ifdef CONFIG_SDCARD +#define CONFIG_RAMBOOT_SDCARD +#define CONFIG_SYS_TEXT_BASE 0x11000000 +#define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc +#endif + +#ifdef CONFIG_SPIFLASH +#define CONFIG_RAMBOOT_SPIFLASH +#define CONFIG_SYS_TEXT_BASE 0x11000000 +#define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc +#endif + +#ifndef CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_TEXT_BASE 0xeff80000 +#endif + +#ifndef CONFIG_RESET_VECTOR_ADDRESS +#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc +#endif + +#ifndef CONFIG_SYS_MONITOR_BASE +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ +#endif + +/* High Level Configuration Options */ +#define CONFIG_BOOKE /* BOOKE */ +#define CONFIG_E500 /* BOOKE e500 family */ +#define CONFIG_MPC85xx +#define CONFIG_FSL_IFC /* Enable IFC Support */ +#define CONFIG_SYS_HAS_SERDES /* common SERDES init code */ + +#define CONFIG_PCI /* Enable PCI/PCIE */ +#if defined(CONFIG_PCI) +#define CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */ +#define CONFIG_PCIE2 /* PCIE controler 2 (slot 2) */ +#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ +#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */ +#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ + +#define CONFIG_CMD_NET +#define CONFIG_CMD_PCI + +#define CONFIG_E1000 /* E1000 pci Ethernet card*/ + +/* + * PCI Windows + * Memory space is mapped 1-1, but I/O space must start from 0. + */ +/* controller 1, Slot 1, tgtid 1, Base address a000 */ +#define CONFIG_SYS_PCIE1_NAME "mini PCIe Slot" +#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull +#else +#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 +#endif +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc00000ull +#else +#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc00000 +#endif + +/* controller 2, Slot 2, tgtid 2, Base address 9000 */ +#define CONFIG_SYS_PCIE2_NAME "PCIe Slot" +#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull +#else +#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 +#endif +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 +#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_PCIE2_IO_PHYS 0xfffc10000ull +#else +#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000 +#endif + +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_DOS_PARTITION +#endif + +#define CONFIG_FSL_LAW /* Use common FSL init code */ +#define CONFIG_TSEC_ENET +#define CONFIG_ENV_OVERWRITE + +#define CONFIG_DDR_CLK_FREQ 66666666 /* DDRCLK on P1010 RDB */ +#define CONFIG_SYS_CLK_FREQ 66666666 /* SYSCLK for P1010 RDB */ + +#ifndef CONFIG_SDCARD +#define CONFIG_MISC_INIT_R +#endif + +#define CONFIG_HWCONFIG +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#define CONFIG_BTB /* toggle branch predition */ + +#define CONFIG_ADDR_STREAMING /* toggle addr streaming */ + +#define CONFIG_ENABLE_36BIT_PHYS + +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_ADDR_MAP 1 +#define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */ +#endif + +#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x1fffffff +#define CONFIG_PANIC_HANG /* do not reset board on panic */ + +/* DDR Setup */ +#define CONFIG_FSL_DDR3 +#define CONFIG_DDR_RAW_TIMING +#define CONFIG_DDR_SPD +#define CONFIG_SYS_SPD_BUS_NUM 1 +#define SPD_EEPROM_ADDRESS 0x52 + +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef + +#ifndef __ASSEMBLY__ +extern unsigned long get_sdram_size(void); +#endif +#define CONFIG_SYS_SDRAM_SIZE get_sdram_size() /* DDR size */ +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL 1 + +/* DDR3 Controller Settings */ +#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f +#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302 +#define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000 +#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef +#define CONFIG_SYS_DDR_INIT_ADDR 0x00000000 +#define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000 +#define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000 + +#define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600 +#define CONFIG_SYS_DDR_SR_CNTR 0x00000000 +#define CONFIG_SYS_DDR_RCW_1 0x00000000 +#define CONFIG_SYS_DDR_RCW_2 0x00000000 +#define CONFIG_SYS_DDR_CONTROL 0x470C0000 /* Type = DDR3 */ +#define CONFIG_SYS_DDR_CONTROL_2 0x04401010 +#define CONFIG_SYS_DDR_TIMING_4 0x00000001 +#define CONFIG_SYS_DDR_TIMING_5 0x03402400 + +#define CONFIG_SYS_DDR_TIMING_3_800 0x00020000 +#define CONFIG_SYS_DDR_TIMING_0_800 0x00330004 +#define CONFIG_SYS_DDR_TIMING_1_800 0x6f6B4644 +#define CONFIG_SYS_DDR_TIMING_2_800 0x0FA888CF +#define CONFIG_SYS_DDR_CLK_CTRL_800 0x03000000 +#define CONFIG_SYS_DDR_MODE_1_800 0x40461520 +#define CONFIG_SYS_DDR_MODE_2_800 0x8000c000 +#define CONFIG_SYS_DDR_INTERVAL_800 0x0C300100 +#define CONFIG_SYS_DDR_WRLVL_CONTROL_800 0x8655A608 + +/* settings for DDR3 at 667MT/s */ +#define CONFIG_SYS_DDR_TIMING_3_667 0x00010000 +#define CONFIG_SYS_DDR_TIMING_0_667 0x00110004 +#define CONFIG_SYS_DDR_TIMING_1_667 0x5d59e544 +#define CONFIG_SYS_DDR_TIMING_2_667 0x0FA890CD +#define CONFIG_SYS_DDR_CLK_CTRL_667 0x03000000 +#define CONFIG_SYS_DDR_MODE_1_667 0x00441210 +#define CONFIG_SYS_DDR_MODE_2_667 0x00000000 +#define CONFIG_SYS_DDR_INTERVAL_667 0x0a280000 +#define CONFIG_SYS_DDR_WRLVL_CONTROL_667 0x8675F608 + +#define CONFIG_SYS_CCSRBAR 0xffe00000 +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR + +/* + * Memory map + * + * 0x0000_0000 0x3fff_ffff DDR 1G cacheable + * 0x8000_0000 0xbfff_ffff PCI Express Mem 1.5G non-cacheable + * 0xffc0_0000 0xffc3_ffff PCI IO range 256k non-cacheable + * + * Localbus non-cacheable + * 0xff80_0000 0xff8f_ffff NAND Flash 1M non-cacheable + * 0xffb0_0000 0xffbf_ffff Board CPLD 1M non-cacheable + * 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0 + * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable + */ + +/* In case of SD card boot, IFC interface is not available because of muxing */ +#ifdef CONFIG_SDCARD +#define CONFIG_SYS_NO_FLASH +#else +/* + * IFC Definitions + */ +/* NOR Flash on IFC */ +#define CONFIG_SYS_FLASH_BASE 0xee000000 +#define CONFIG_SYS_MAX_FLASH_SECT 256 /* 32M */ + +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) +#else +#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE +#endif + +#define CONFIG_SYS_NOR_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ + CSPR_PORT_SIZE_16 | \ + CSPR_MSEL_NOR | \ + CSPR_V) +#define CONFIG_SYS_NOR_AMASK IFC_AMASK(32*1024*1024) +#define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(7) +/* NOR Flash Timing Params */ +#define CONFIG_SYS_NOR_FTIM0 FTIM0_NOR_TACSE(0x4) | \ + FTIM0_NOR_TEADC(0x5) | \ + FTIM0_NOR_TEAHC(0x5) +#define CONFIG_SYS_NOR_FTIM1 FTIM1_NOR_TACO(0x1e) | \ + FTIM1_NOR_TRAD_NOR(0x0f) +#define CONFIG_SYS_NOR_FTIM2 FTIM2_NOR_TCS(0x4) | \ + FTIM2_NOR_TCH(0x4) | \ + FTIM2_NOR_TWP(0x1c) +#define CONFIG_SYS_NOR_FTIM3 0x0 + +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} +#define CONFIG_SYS_FLASH_QUIET_TEST +#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ + +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +/* CFI for NOR Flash */ +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE + +/* NAND Flash on IFC */ +#define CONFIG_SYS_NAND_BASE 0xff800000 +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_NAND_BASE_PHYS 0xfff800000ull +#else +#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE +#endif + +#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ + | CSPR_PORT_SIZE_8 \ + | CSPR_MSEL_NAND \ + | CSPR_V) +#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) +#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ + | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ + | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ + | CSOR_NAND_RAL_2 /* RAL = 2 Bytes */ \ + | CSOR_NAND_PGS_512 /* Page Size = 512b */ \ + | CSOR_NAND_SPRZ_16 /* Spare size = 16 */ \ + | CSOR_NAND_PB(32)) /* 32 Pages Per Block */ + +/* NAND Flash Timing Params */ +#define CONFIG_SYS_NAND_FTIM0 FTIM0_NAND_TCCST(0x01) | \ + FTIM0_NAND_TWP(0x0C) | \ + FTIM0_NAND_TWCHT(0x04) | \ + FTIM0_NAND_TWH(0x05) +#define CONFIG_SYS_NAND_FTIM1 FTIM1_NAND_TADLE(0x1d) | \ + FTIM1_NAND_TWBE(0x1d) | \ + FTIM1_NAND_TRR(0x07) | \ + FTIM1_NAND_TRP(0x0c) +#define CONFIG_SYS_NAND_FTIM2 FTIM2_NAND_TRAD(0x0c) | \ + FTIM2_NAND_TREH(0x05) | \ + FTIM2_NAND_TWHRE(0x0f) +#define CONFIG_SYS_NAND_FTIM3 FTIM3_NAND_TWW(0x04) + +#define CONFIG_SYS_NAND_DDR_LAW 11 + +/* Set up IFC registers for boot location NOR/NAND */ +#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR_CSPR +#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 +#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR +#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK +#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR +#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0 +#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1 +#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2 +#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3 + +/* CPLD on IFC */ +#define CONFIG_SYS_CPLD_BASE 0xffb00000 + +#ifdef CONFIG_PHYS_64BIT +#define CONFIG_SYS_CPLD_BASE_PHYS 0xfffb00000ull +#else +#define CONFIG_SYS_CPLD_BASE_PHYS CONFIG_SYS_CPLD_BASE +#endif + +#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE_PHYS) \ + | CSPR_PORT_SIZE_8 \ + | CSPR_MSEL_GPCM \ + | CSPR_V) +#define CONFIG_SYS_AMASK3 IFC_AMASK(64*1024) +#define CONFIG_SYS_CSOR3 0x0 +/* CPLD Timing parameters for IFC CS3 */ +#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ + FTIM0_GPCM_TEADC(0x0e) | \ + FTIM0_GPCM_TEAHC(0x0e)) +#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \ + FTIM1_GPCM_TRAD(0x1f)) +#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ + FTIM2_GPCM_TCH(0x0) | \ + FTIM2_GPCM_TWP(0x1f)) +#define CONFIG_SYS_CS3_FTIM3 0x0 +#endif /* CONFIG_SDCARD */ + +#if defined(CONFIG_RAMBOOT_SDCARD) || defined(CONFIG_RAMBOOT_SPIFLASH) || \ + defined(CONFIG_RAMBOOT_NAND) +#define CONFIG_SYS_RAMBOOT +#define CONFIG_SYS_EXTRA_ENV_RELOC +#else +#undef CONFIG_SYS_RAMBOOT +#endif + +#define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */ +#define CONFIG_BOARD_EARLY_INIT_R + +#define CONFIG_SYS_INIT_RAM_LOCK +#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */ +#define CONFIG_SYS_INIT_RAM_END 0x00004000 /* End of used area in RAM */ + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END \ + - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon*/ +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc*/ + +/* Serial Port */ +#define CONFIG_CONS_INDEX 1 +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) + +#define CONFIG_SERIAL_MULTI /* Enable both serial ports */ +#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */ + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#endif + +/* + * Pass open firmware flat tree + */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP +#define CONFIG_OF_STDOUT_VIA_ALIAS + +/* new uImage format support */ +#define CONFIG_FIT +#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ + +#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_I2C_CMD_TREE +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address*/ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C2_OFFSET 0x3100 + +/* I2C EEPROM */ +#undef CONFIG_ID_EEPROM +/* enable read and write access to EEPROM */ +#define CONFIG_CMD_EEPROM +#define CONFIG_SYS_I2C_MULTI_EEPROMS +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 + +/* RTC */ +#define CONFIG_RTC_PT7C4338 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 + +#define CONFIG_CMD_I2C + +/* + * SPI interface will not be available in case of NAND boot SPI CS0 will be + * used for SLIC + */ +/* eSPI - Enhanced SPI */ +#define CONFIG_FSL_ESPI +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_SPANSION +#define CONFIG_CMD_SF +#define CONFIG_SF_DEFAULT_SPEED 10000000 +#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 + +#if defined(CONFIG_TSEC_ENET) +#ifndef CONFIG_NET_MULTI +#define CONFIG_NET_MULTI +#endif + +#define CONFIG_MII /* MII PHY management */ +#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ +#define CONFIG_TSEC1 1 +#define CONFIG_TSEC1_NAME "eTSEC1" +#define CONFIG_TSEC2 1 +#define CONFIG_TSEC2_NAME "eTSEC2" +#define CONFIG_TSEC3 1 +#define CONFIG_TSEC3_NAME "eTSEC3" + +#define TSEC1_PHY_ADDR 1 +#define TSEC2_PHY_ADDR 0 +#define TSEC3_PHY_ADDR 2 + +#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) + +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 +#define TSEC3_PHYIDX 0 + +#define CONFIG_ETHPRIME "eTSEC1" + +#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ + +/* TBI PHY configuration for SGMII mode */ +#define CONFIG_TSEC_TBICR_SETTINGS ( \ + TBICR_PHY_RESET \ + | TBICR_ANEG_ENABLE \ + | TBICR_FULL_DUPLEX \ + | TBICR_SPEED1_SET \ + ) + +#endif /* CONFIG_TSEC_ENET */ + + +/* SATA */ +#define CONFIG_FSL_SATA +#define CONFIG_LIBATA + +#ifdef CONFIG_FSL_SATA +#define CONFIG_SYS_SATA_MAX_DEVICE 2 +#define CONFIG_SATA1 +#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR +#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA +#define CONFIG_SATA2 +#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR +#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA + +#define CONFIG_CMD_SATA +#define CONFIG_LBA48 +#endif /* #ifdef CONFIG_FSL_SATA */ + +/* SD interface will only be available in case of SD boot */ +#ifdef CONFIG_SDCARD +#define CONFIG_MMC +#define CONFIG_DEF_HWCONFIG esdhc +#endif + +#ifdef CONFIG_MMC +#define CONFIG_CMD_MMC +#define CONFIG_DOS_PARTITION +#define CONFIG_FSL_ESDHC +#define CONFIG_GENERIC_MMC +#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR +#endif + +#define CONFIG_HAS_FSL_DR_USB + +#if defined(CONFIG_HAS_FSL_DR_USB) +#define CONFIG_USB_EHCI + +#ifdef CONFIG_USB_EHCI +#define CONFIG_CMD_USB +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_USB_EHCI_FSL +#define CONFIG_USB_STORAGE +#endif +#endif + +/* + * Environment + */ +#if defined(CONFIG_SYS_RAMBOOT) +#if defined(CONFIG_RAMBOOT_SDCARD) +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_ENV_SIZE 0x2000 +#elif defined(CONFIG_RAMBOOT_SPIFLASH) +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 0 +#define CONFIG_ENV_SPI_MAX_HZ 10000000 +#define CONFIG_ENV_SPI_MODE 0 +#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ +#define CONFIG_ENV_SECT_SIZE 0x10000 +#define CONFIG_ENV_SIZE 0x2000 +#else +#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */ +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) +#define CONFIG_ENV_SIZE 0x2000 +#endif +#else +#define CONFIG_ENV_IS_IN_FLASH +#if CONFIG_SYS_MONITOR_BASE > 0xfff80000 +#define CONFIG_ENV_ADDR 0xfff80000 +#else +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) +#endif +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ +#endif + +#define CONFIG_LOADS_ECHO /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_DATE +#define CONFIG_CMD_ERRATA +#define CONFIG_CMD_ELF +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_SETEXPR +#define CONFIG_CMD_REGINFO + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) \ + || defined(CONFIG_FSL_SATA) +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) + /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* dec freq: 1ms ticks */ + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 64 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ + +#if defined(CONFIG_TSEC_ENET) +#define CONFIG_HAS_ETH0 +#define CONFIG_HAS_ETH1 +#define CONFIG_HAS_ETH2 +#endif + +#define CONFIG_HOSTNAME P1010RDB +#define CONFIG_ROOTPATH /opt/nfsroot +#define CONFIG_BOOTFILE uImage +#define CONFIG_UBOOTPATH u-boot.bin/* U-Boot image on TFTP server */ + +/* default location for tftp and bootm */ +#define CONFIG_LOADADDR 1000000 + +#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ +#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "hwconfig=" MK_STR(CONFIG_DEF_HWCONFIG) "\0" \ + "netdev=eth0\0" \ + "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \ + "loadaddr=1000000\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=2000000\0" \ + "ramdiskfile=rootfs.ext2.gz.uboot\0" \ + "fdtaddr=c00000\0" \ + "fdtfile=p1010rdb.dtb\0" \ + "bdev=sda1\0" \ + "hwconfig=usb1:dr_mode=host,phy_type=utmi\0" \ + "othbootargs=ramdisk_size=600000\0" \ + "usbfatboot=setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs; " \ + "usb start;" \ + "fatload usb 0:2 $loadaddr $bootfile;" \ + "fatload usb 0:2 $fdtaddr $fdtfile;" \ + "fatload usb 0:2 $ramdiskaddr $ramdiskfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \ + "usbext2boot=setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs; " \ + "usb start;" \ + "ext2load usb 0:4 $loadaddr $bootfile;" \ + "ext2load usb 0:4 $fdtaddr $fdtfile;" \ + "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \ + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs; " \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND + +#endif /* __CONFIG_H */ |