arm: mvebu: Add basic Armada XP / 38x dtsi/dts files

These will be needed by the upcoming DM (driver model) support for
the Armada XP / 38x SoC's. This will provide DT based probing.

The dts files are copied 1:1 from the Linux kernel release v4.2.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>

1 files changed, 245 insertions, 0 deletions

diff --git a/arch/arm/dts/armada-xp-gp.dts b/arch/arm/dts/armada-xp-gp.dts
new file mode 100644
index 0000000..bf724ca
--- /dev/null
+++ b/arch/arm/dts/armada-xp-gp.dts
@@ -0,0 +1,245 @@
+/*
+ * Device Tree file for Marvell Armada XP development board
+ * (DB-MV784MP-GP)
+ *
+ * Copyright (C) 2013-2014 Marvell
+ *
+ * Lior Amsalem <alior@marvell.com>
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Note: this Device Tree assumes that the bootloader has remapped the
+ * internal registers to 0xf1000000 (instead of the default
+ * 0xd0000000). The 0xf1000000 is the default used by the recent,
+ * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
+ * boards were delivered with an older version of the bootloader that
+ * left internal registers mapped at 0xd0000000. If you are in this
+ * situation, you should either update your bootloader (preferred
+ * solution) or the below Device Tree should be adjusted.
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-xp-mv78460.dtsi"
+
+/ {
+	model = "Marvell Armada XP Development Board DB-MV784MP-GP";
+	compatible = "marvell,axp-gp", "marvell,armadaxp-mv78460", "marvell,armadaxp", "marvell,armada-370-xp";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		device_type = "memory";
+		/*
+                 * 8 GB of plug-in RAM modules by default.The amount
+                 * of memory available can be changed by the
+                 * bootloader according the size of the module
+                 * actually plugged. However, memory between
+                 * 0xF0000000 to 0xFFFFFFFF cannot be used, as it is
+                 * the address range used for I/O (internal registers,
+                 * MBus windows).
+		 */
+		reg = <0x00000000 0x00000000 0x00000000 0xf0000000>,
+		      <0x00000001 0x00000000 0x00000001 0x00000000>;
+	};
+
+	cpus {
+		pm_pic {
+			ctrl-gpios = <&gpio0 16 GPIO_ACTIVE_LOW>,
+				     <&gpio0 17 GPIO_ACTIVE_LOW>,
+				     <&gpio0 18 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
+			  MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000>;
+
+		devbus-bootcs {
+			status = "okay";
+
+			/* Device Bus parameters are required */
+
+			/* Read parameters */
+			devbus,bus-width    = <16>;
+			devbus,turn-off-ps  = <60000>;
+			devbus,badr-skew-ps = <0>;
+			devbus,acc-first-ps = <124000>;
+			devbus,acc-next-ps  = <248000>;
+			devbus,rd-setup-ps  = <0>;
+			devbus,rd-hold-ps   = <0>;
+
+			/* Write parameters */
+			devbus,sync-enable = <0>;
+			devbus,wr-high-ps  = <60000>;
+			devbus,wr-low-ps   = <60000>;
+			devbus,ale-wr-ps   = <60000>;
+
+			/* NOR 16 MiB */
+			nor@0 {
+				compatible = "cfi-flash";
+				reg = <0 0x1000000>;
+				bank-width = <2>;
+			};
+		};
+
+		pcie-controller {
+			status = "okay";
+
+			/*
+			 * The 3 slots are physically present as
+			 * standard PCIe slots on the board.
+			 */
+			pcie@1,0 {
+				/* Port 0, Lane 0 */
+				status = "okay";
+			};
+			pcie@9,0 {
+				/* Port 2, Lane 0 */
+				status = "okay";
+			};
+			pcie@10,0 {
+				/* Port 3, Lane 0 */
+				status = "okay";
+			};
+		};
+
+		internal-regs {
+			serial@12000 {
+				status = "okay";
+			};
+			serial@12100 {
+				status = "okay";
+			};
+			serial@12200 {
+				status = "okay";
+			};
+			serial@12300 {
+				status = "okay";
+			};
+			pinctrl {
+				pinctrl-0 = <&pic_pins>;
+				pinctrl-names = "default";
+				pic_pins: pic-pins-0 {
+					marvell,pins = "mpp16", "mpp17",
+						       "mpp18";
+					marvell,function = "gpio";
+				};
+			};
+			sata@a0000 {
+				nr-ports = <2>;
+				status = "okay";
+			};
+
+			mdio {
+				phy0: ethernet-phy@0 {
+					reg = <16>;
+				};
+
+				phy1: ethernet-phy@1 {
+					reg = <17>;
+				};
+
+				phy2: ethernet-phy@2 {
+					reg = <18>;
+				};
+
+				phy3: ethernet-phy@3 {
+					reg = <19>;
+				};
+			};
+
+			ethernet@70000 {
+				status = "okay";
+				phy = <&phy0>;
+				phy-mode = "qsgmii";
+			};
+			ethernet@74000 {
+				status = "okay";
+				phy = <&phy1>;
+				phy-mode = "qsgmii";
+			};
+			ethernet@30000 {
+				status = "okay";
+				phy = <&phy2>;
+				phy-mode = "qsgmii";
+			};
+			ethernet@34000 {
+				status = "okay";
+				phy = <&phy3>;
+				phy-mode = "qsgmii";
+			};
+
+			/* Front-side USB slot */
+			usb@50000 {
+				status = "okay";
+			};
+
+			/* Back-side USB slot */
+			usb@51000 {
+				status = "okay";
+			};
+
+			spi0: spi@10600 {
+				status = "okay";
+
+				spi-flash@0 {
+					#address-cells = <1>;
+					#size-cells = <1>;
+					compatible = "n25q128a13", "jedec,spi-nor";
+					reg = <0>; /* Chip select 0 */
+					spi-max-frequency = <108000000>;
+				};
+			};
+
+			nand@d0000 {
+				status = "okay";
+				num-cs = <1>;
+				marvell,nand-keep-config;
+				marvell,nand-enable-arbiter;
+				nand-on-flash-bbt;
+			};
+		};
+	};
+};