Merge git://git.denx.de/u-boot-fsl-qoriq

Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	arch/arm/Kconfig

21 files changed, 629 insertions, 28 deletions

diff --git a/board/freescale/ls1021aiot/Kconfig b/board/freescale/ls1021aiot/Kconfig
new file mode 100644
index 0000000..4a12c16
--- /dev/null
+++ b/board/freescale/ls1021aiot/Kconfig
@@ -0,0 +1,15 @@
+if TARGET_LS1021AIOT
+
+config SYS_BOARD
+	default "ls1021aiot"
+
+config SYS_VENDOR
+	default "freescale"
+
+config SYS_SOC
+	default "ls102xa"
+
+config SYS_CONFIG_NAME
+	default "ls1021aiot"
+
+endif
diff --git a/board/freescale/ls1021aiot/MAINTAINERS b/board/freescale/ls1021aiot/MAINTAINERS
new file mode 100644
index 0000000..2dab798
--- /dev/null
+++ b/board/freescale/ls1021aiot/MAINTAINERS
@@ -0,0 +1,7 @@
+LS1021AIOT BOARD
+M:	Feng Li <feng.li_2@nxp.com>
+S:	Maintained
+F:	board/freescale/ls1021aiot/
+F:	include/configs/ls1021aiot.h
+F:	configs/ls1021aiot_sdcard_defconfig
+F:	configs/ls1021aiot_qspi_defconfig
diff --git a/board/freescale/ls1021aiot/Makefile b/board/freescale/ls1021aiot/Makefile
new file mode 100644
index 0000000..05709e6
--- /dev/null
+++ b/board/freescale/ls1021aiot/Makefile
@@ -0,0 +1,9 @@
+#
+# Copyright 2016 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y += ls1021aiot.o
+obj-$(CONFIG_FSL_DCU_FB) += dcu.o
+obj-$(CONFIG_ARMV7_PSCI) += psci.o
diff --git a/board/freescale/ls1021aiot/README b/board/freescale/ls1021aiot/README
new file mode 100644
index 0000000..08b0268
--- /dev/null
+++ b/board/freescale/ls1021aiot/README
@@ -0,0 +1,58 @@
+Overview
+--------
+The LS1021A-IOT is a Freescale reference board that hosts
+the LS1021A SoC.
+
+LS1021AIOT board Overview
+-------------------------
+ - DDR Controller
+	- Supports 1GB un-buffered DDR3L SDRAM discrete
+	devices(32-bit bus) with 4 bit ECC
+	- DDR power supplies 1.35V to all devices with
+	automatic tracking of VTT
+	- Soldered DDR chip
+	- Supprot one fixed speed
+ - Ethernet
+	- Two on-board SGMII 10/100/1G ethernet ports
+	- One Gbit Etherent RGMII interface to 4-ports switch
+	with 4x 10/100/1000 RJ145 ports
+ - CPLD
+	- 8-bit registers in CPLD for system configuration
+	- connected to IFC_AD[0:7]
+ - Power Supplies
+	- 12V@5A DC
+ - SDHC
+	- SDHC port connects directly to a full 8-bit SD/MMC slot
+	- Support for SDIO devices
+ - USB
+	- Two on-board USB 3.0
+	- One on-board USB k22
+ - PCIe
+	- Two MiniPCIe Solts
+ - SATA
+	- Support SATA Connector
+ - AUDIO
+	- AUDIO in and out
+ - I/O Expansion
+	- Arduino Shield Connector
+	- Port0 - CAN/GPIO/Flextimer
+	- Port1 - GPIO/CPLD Expansion
+	- Port2 - SPI/I2C/UART
+
+Memory map
+-----------
+The addresses in brackets are physical addresses.
+
+Start Address	End Address		Description			Size
+0x00_0100_0000	0x00_0FFF_FFFF	CCSRBAR				240MB
+0x00_4000_0000	0x00_43FF_FFFF	QSPI(Chip select 0)	64MB
+0x00_4400_0000	0x00_47FF_FFFF	QSPI(Chip select 1)	64MB
+0x00_6000_0000	0x00_6000_FFFF	CPLD				64K
+0x00_8000_0000	0x00_BFFF_FFFF	DDR					1GB
+
+Boot description
+-----------------
+LS1021A-IOT support two ways of boot:
+Qspi boot and SD boot
+The board doesn't support boot from another
+source without changing any switch/jumper.
diff --git a/board/freescale/ls1021aiot/dcu.c b/board/freescale/ls1021aiot/dcu.c
new file mode 100644
index 0000000..e27647f
--- /dev/null
+++ b/board/freescale/ls1021aiot/dcu.c
@@ -0,0 +1,47 @@
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * FSL DCU Framebuffer driver
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <fsl_dcu_fb.h>
+#include "div64.h"
+#include "../common/dcu_sii9022a.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+unsigned int dcu_set_pixel_clock(unsigned int pixclock)
+{
+	unsigned long long div;
+
+	div = (unsigned long long)(gd->bus_clk / 1000);
+	div *= (unsigned long long)pixclock;
+	do_div(div, 1000000000);
+
+	return div;
+}
+
+int platform_dcu_init(unsigned int xres, unsigned int yres,
+		const char *port,
+		struct fb_videomode *dcu_fb_videomode)
+{
+	const char *name;
+	unsigned int pixel_format;
+
+	if (strncmp(port, "twr_lcd", 4) == 0) {
+		name = "TWR_LCD_RGB card";
+	} else {
+		name = "HDMI";
+		dcu_set_dvi_encoder(dcu_fb_videomode);
+	}
+
+	printf("DCU: Switching to %s monitor @ %ux%u\n", name, xres, yres);
+
+	pixel_format = 32;
+	fsl_dcu_init(xres, yres, pixel_format);
+
+	return 0;
+}
diff --git a/board/freescale/ls1021aiot/ls1021aiot.c b/board/freescale/ls1021aiot/ls1021aiot.c
new file mode 100644
index 0000000..3340e4d
--- /dev/null
+++ b/board/freescale/ls1021aiot/ls1021aiot.c
@@ -0,0 +1,259 @@
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/immap_ls102xa.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/fsl_serdes.h>
+#include <asm/arch/ls102xa_stream_id.h>
+
+#include <asm/arch/ls102xa_devdis.h>
+#include <asm/arch/ls102xa_soc.h>
+#include <asm/arch/ls102xa_sata.h>
+#include <fsl_csu.h>
+#include <fsl_esdhc.h>
+#include <fsl_immap.h>
+#include <netdev.h>
+#include <fsl_mdio.h>
+#include <tsec.h>
+#include <spl.h>
+
+#include <fsl_validate.h>
+#include "../common/sleep.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define DDR_SIZE		0x40000000
+
+
+int checkboard(void)
+{
+	puts("Board: LS1021AIOT\n");
+
+#ifndef CONFIG_QSPI_BOOT
+	struct ccsr_gur *dcfg = (struct ccsr_gur *)CONFIG_SYS_FSL_GUTS_ADDR;
+	u32 cpldrev;
+
+	cpldrev = in_be32(&dcfg->gpporcr1);
+
+	printf("CPLD:  V%d.%d\n", ((cpldrev >> 28) & 0xf), ((cpldrev >> 24) &
+		0xf));
+#endif
+	return 0;
+}
+
+void ddrmc_init(void)
+{
+	struct ccsr_ddr *ddr = (struct ccsr_ddr *)CONFIG_SYS_FSL_DDR_ADDR;
+	u32 temp_sdram_cfg, tmp;
+
+	out_be32(&ddr->sdram_cfg, DDR_SDRAM_CFG);
+
+	out_be32(&ddr->cs0_bnds, DDR_CS0_BNDS);
+	out_be32(&ddr->cs0_config, DDR_CS0_CONFIG);
+
+	out_be32(&ddr->timing_cfg_0, DDR_TIMING_CFG_0);
+	out_be32(&ddr->timing_cfg_1, DDR_TIMING_CFG_1);
+	out_be32(&ddr->timing_cfg_2, DDR_TIMING_CFG_2);
+	out_be32(&ddr->timing_cfg_3, DDR_TIMING_CFG_3);
+	out_be32(&ddr->timing_cfg_4, DDR_TIMING_CFG_4);
+	out_be32(&ddr->timing_cfg_5, DDR_TIMING_CFG_5);
+
+	out_be32(&ddr->sdram_cfg_2, DDR_SDRAM_CFG_2);
+	out_be32(&ddr->ddr_cdr2, DDR_DDR_CDR2);
+
+	out_be32(&ddr->sdram_mode, DDR_SDRAM_MODE);
+	out_be32(&ddr->sdram_mode_2, DDR_SDRAM_MODE_2);
+
+	out_be32(&ddr->sdram_interval, DDR_SDRAM_INTERVAL);
+
+	out_be32(&ddr->ddr_wrlvl_cntl, DDR_DDR_WRLVL_CNTL);
+
+	out_be32(&ddr->ddr_wrlvl_cntl_2, DDR_DDR_WRLVL_CNTL_2);
+	out_be32(&ddr->ddr_wrlvl_cntl_3, DDR_DDR_WRLVL_CNTL_3);
+
+	out_be32(&ddr->ddr_cdr1, DDR_DDR_CDR1);
+
+	out_be32(&ddr->sdram_clk_cntl, DDR_SDRAM_CLK_CNTL);
+	out_be32(&ddr->ddr_zq_cntl, DDR_DDR_ZQ_CNTL);
+
+	out_be32(&ddr->cs0_config_2, DDR_CS0_CONFIG_2);
+
+	/* DDR erratum A-009942 */
+	tmp = in_be32(&ddr->debug[28]);
+	out_be32(&ddr->debug[28], tmp | 0x0070006f);
+
+	udelay(500);
+
+	temp_sdram_cfg = (DDR_SDRAM_CFG_MEM_EN & ~SDRAM_CFG_BI);
+
+	out_be32(&ddr->sdram_cfg, DDR_SDRAM_CFG | temp_sdram_cfg);
+}
+
+int dram_init(void)
+{
+#if (!defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD))
+	ddrmc_init();
+#endif
+
+	gd->ram_size = DDR_SIZE;
+	return 0;
+}
+
+#ifdef CONFIG_FSL_ESDHC
+struct fsl_esdhc_cfg esdhc_cfg[1] = {
+	{CONFIG_SYS_FSL_ESDHC_ADDR},
+};
+
+int board_mmc_init(bd_t *bis)
+{
+	esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+
+	return fsl_esdhc_initialize(bis, &esdhc_cfg[0]);
+}
+
+#endif
+
+#ifdef CONFIG_TSEC_ENET
+int board_eth_init(bd_t *bis)
+{
+	struct fsl_pq_mdio_info mdio_info;
+	struct tsec_info_struct tsec_info[4];
+	int num = 0;
+
+#ifdef CONFIG_TSEC1
+	SET_STD_TSEC_INFO(tsec_info[num], 1);
+	if (is_serdes_configured(SGMII_TSEC1)) {
+		puts("eTSEC1 is in sgmii mode.\n");
+		tsec_info[num].flags |= TSEC_SGMII;
+	}
+	num++;
+#endif
+#ifdef CONFIG_TSEC2
+	SET_STD_TSEC_INFO(tsec_info[num], 2);
+	if (is_serdes_configured(SGMII_TSEC2)) {
+		puts("eTSEC2 is in sgmii mode.\n");
+		tsec_info[num].flags |= TSEC_SGMII;
+	}
+	num++;
+#endif
+	if (!num) {
+		printf("No TSECs initialized\n");
+		return 0;
+	}
+
+	mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
+	mdio_info.name = DEFAULT_MII_NAME;
+	fsl_pq_mdio_init(bis, &mdio_info);
+
+	tsec_eth_init(bis, tsec_info, num);
+
+	return pci_eth_init(bis);
+}
+#endif
+
+int board_early_init_f(void)
+{
+	struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR;
+
+#ifdef CONFIG_TSEC_ENET
+	/* clear BD & FR bits for BE BD's and frame data */
+	clrbits_be32(&scfg->etsecdmamcr, SCFG_ETSECDMAMCR_LE_BD_FR);
+	out_be32(&scfg->etsecmcr, SCFG_ETSECCMCR_GE2_CLK125);
+
+#endif
+
+	arch_soc_init();
+
+	return 0;
+}
+
+#ifdef CONFIG_SPL_BUILD
+void board_init_f(ulong dummy)
+{
+	/* Clear the BSS */
+	memset(__bss_start, 0, __bss_end - __bss_start);
+
+	get_clocks();
+
+	preloader_console_init();
+
+	dram_init();
+
+	/* Allow OCRAM access permission as R/W */
+
+#ifdef CONFIG_LAYERSCAPE_NS_ACCESS
+	enable_layerscape_ns_access();
+#endif
+
+	board_init_r(NULL, 0);
+}
+#endif
+
+int board_init(void)
+{
+#ifndef CONFIG_SYS_FSL_NO_SERDES
+	fsl_serdes_init();
+#endif
+
+	ls102xa_smmu_stream_id_init();
+
+#ifdef CONFIG_LAYERSCAPE_NS_ACCESS
+	enable_layerscape_ns_access();
+#endif
+
+	return 0;
+}
+
+#ifdef CONFIG_BOARD_LATE_INIT
+int board_late_init(void)
+{
+#ifdef CONFIG_SCSI_AHCI_PLAT
+	ls1021a_sata_init();
+#endif
+
+	return 0;
+}
+#endif
+
+#if defined(CONFIG_MISC_INIT_R)
+int misc_init_r(void)
+{
+#ifdef CONFIG_FSL_DEVICE_DISABLE
+	device_disable(devdis_tbl, ARRAY_SIZE(devdis_tbl));
+
+#endif
+
+#ifdef CONFIG_FSL_CAAM
+	return sec_init();
+#endif
+}
+#endif
+
+int ft_board_setup(void *blob, bd_t *bd)
+{
+	ft_cpu_setup(blob, bd);
+
+#ifdef CONFIG_PCI
+	ft_pci_setup(blob, bd);
+#endif
+
+	return 0;
+}
+
+void flash_write16(u16 val, void *addr)
+{
+	u16 shftval = (((val >> 8) & 0xff) | ((val << 8) & 0xff00));
+
+	__raw_writew(shftval, addr);
+}
+
+u16 flash_read16(void *addr)
+{
+	u16 val = __raw_readw(addr);
+
+	return (((val) >> 8) & 0x00ff) | (((val) << 8) & 0xff00);
+}
diff --git a/board/freescale/ls1021aiot/ls102xa_pbi.cfg b/board/freescale/ls1021aiot/ls102xa_pbi.cfg
new file mode 100644
index 0000000..b5ac5e2
--- /dev/null
+++ b/board/freescale/ls1021aiot/ls102xa_pbi.cfg
@@ -0,0 +1,14 @@
+#PBI commands
+
+09570200 ffffffff
+09570158 00000300
+8940007c 21f47300
+
+#Configure Scratch register
+09ee0200 10000000
+#Configure alternate space
+09570158 00001000
+#Flush PBL data
+096100c0 000FFFFF
+
+09ea085c 00502880
diff --git a/board/freescale/ls1021aiot/ls102xa_rcw_sd.cfg b/board/freescale/ls1021aiot/ls102xa_rcw_sd.cfg
new file mode 100644
index 0000000..a1984c7
--- /dev/null
+++ b/board/freescale/ls1021aiot/ls102xa_rcw_sd.cfg
@@ -0,0 +1,27 @@
+#PBL preamble and RCW header
+aa55aa55 01ee0100
+# serdes protocol
+
+#Default with 2 x SGMII (no SATA)
+0608000a 00000000 00000000 00000000
+20000000 08407900 60025a00 21046000
+00000000 00000000 00000000 20038000
+20024800 881b1340 00000000 00000000
+
+#SATA set-up
+#0608000a 00000000 00000000 00000000
+#70000000 08007900 60025a00 21046000
+#00000000 00000000 00000000 20038000
+#20024800 881b1340 00000000 00000000
+
+#HDMI set-up
+#0608000a 00000000 00000000 00000000
+#20000000 08407900 60025a00 21046000
+#00000000 00000000 00000000 20038000
+#00000000 881b1340 00000000 00000000
+
+#QE testing
+#0608000a 00000000 00000000 00000000
+#20000000 08407900 60025a00 21046000
+#00000000 00000000 00000000 00038000
+#20094800 881b1340 00000000 00000000
diff --git a/board/freescale/ls1021aiot/psci.S b/board/freescale/ls1021aiot/psci.S
new file mode 100644
index 0000000..564145c
--- /dev/null
+++ b/board/freescale/ls1021aiot/psci.S
@@ -0,0 +1,28 @@
+/*
+ * Copyright 2016 NXP Semiconductor.
+ * Author: Feng Li <feng.li_2@nxp.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <config.h>
+#include <linux/linkage.h>
+
+#include <asm/armv7.h>
+#include <asm/psci.h>
+
+	.pushsection ._secure.text, "ax"
+
+	.arch_extension sec
+
+	.align	5
+
+.globl	psci_system_off
+psci_system_off:
+1:	wfi
+	b	1b
+
+.globl	psci_text_end
+psci_text_end:
+	nop
+	.popsection
diff --git a/board/freescale/ls1021aqds/ls102xa_rcw_nand.cfg b/board/freescale/ls1021aqds/ls102xa_rcw_nand.cfg
index 222c71d..d76e913 100644
--- a/board/freescale/ls1021aqds/ls102xa_rcw_nand.cfg
+++ b/board/freescale/ls1021aqds/ls102xa_rcw_nand.cfg
@@ -1,7 +1,7 @@
 #PBL preamble and RCW header
 aa55aa55 01ee0100
 # serdes protocol
-0608000a 00000000 00000000 00000000
+0608000c 00000000 00000000 00000000
 60000000 00407900 e0106a00 21046000
 00000000 00000000 00000000 00038000
 00000000 001b7200 00000000 00000000
diff --git a/board/freescale/ls1021aqds/ls102xa_rcw_sd_ifc.cfg b/board/freescale/ls1021aqds/ls102xa_rcw_sd_ifc.cfg
index 9d99bd8..f0cf9c2 100644
--- a/board/freescale/ls1021aqds/ls102xa_rcw_sd_ifc.cfg
+++ b/board/freescale/ls1021aqds/ls102xa_rcw_sd_ifc.cfg
@@ -2,13 +2,13 @@
 aa55aa55 01ee0100
 
 #enable IFC, disable QSPI and DSPI
-0608000a 00000000 00000000 00000000
+0608000c 00000000 00000000 00000000
 60000000 00407900 60040a00 21046000
 00000000 00000000 00000000 00038000
 00000000 001b7200 00000000 00000000
 
 #disable IFC, enable QSPI and DSPI
-#0608000a 00000000 00000000 00000000
+#0608000c 00000000 00000000 00000000
 #60000000 00407900 60040a00 21046000
 #00000000 00000000 00000000 00038000
 #20024800 001b7200 00000000 00000000
diff --git a/board/freescale/ls1021aqds/ls102xa_rcw_sd_qspi.cfg b/board/freescale/ls1021aqds/ls102xa_rcw_sd_qspi.cfg
index 2bd398c..10cc4a9 100644
--- a/board/freescale/ls1021aqds/ls102xa_rcw_sd_qspi.cfg
+++ b/board/freescale/ls1021aqds/ls102xa_rcw_sd_qspi.cfg
@@ -2,13 +2,13 @@
 aa55aa55 01ee0100
 
 #enable IFC, disable QSPI and DSPI
-#0608000a 00000000 00000000 00000000
+#0608000c 00000000 00000000 00000000
 #60000000 00407900 60040a00 21046000
 #00000000 00000000 00000000 00038000
 #00000000 001b7200 00000000 00000000
 
 #disable IFC, enable QSPI and DSPI
-0608000a 00000000 00000000 00000000
+0608000c 00000000 00000000 00000000
 60000000 00407900 60040a00 21046000
 00000000 00000000 00000000 00038000
 20024800 001b7200 00000000 00000000
diff --git a/board/freescale/ls1021atwr/ls102xa_rcw_sd_ifc.cfg b/board/freescale/ls1021atwr/ls102xa_rcw_sd_ifc.cfg
index 205606f..f94997d 100644
--- a/board/freescale/ls1021atwr/ls102xa_rcw_sd_ifc.cfg
+++ b/board/freescale/ls1021atwr/ls102xa_rcw_sd_ifc.cfg
@@ -2,7 +2,7 @@
 aa55aa55 01ee0100
 
 #enable IFC, disable QSPI and DSPI
-0608000a 00000000 00000000 00000000
+0608000c 00000000 00000000 00000000
 30000000 00007900 60040a00 21046000
 00000000 00000000 00000000 20000000
 00080000 881b7340 00000000 00000000
diff --git a/board/freescale/ls1021atwr/ls102xa_rcw_sd_qspi.cfg b/board/freescale/ls1021atwr/ls102xa_rcw_sd_qspi.cfg
index 6767e09..541b604 100644
--- a/board/freescale/ls1021atwr/ls102xa_rcw_sd_qspi.cfg
+++ b/board/freescale/ls1021atwr/ls102xa_rcw_sd_qspi.cfg
@@ -2,7 +2,7 @@
 aa55aa55 01ee0100
 
 #disable IFC, enable QSPI and DSPI
-0608000a 00000000 00000000 00000000
+0608000c 00000000 00000000 00000000
 30000000 00007900 60040a00 21046000
 00000000 00000000 00000000 20000000
 20024800 881b7340 00000000 00000000
diff --git a/board/freescale/ls1046aqds/ls1046aqds.c b/board/freescale/ls1046aqds/ls1046aqds.c
index 8c18538..552365b 100644
--- a/board/freescale/ls1046aqds/ls1046aqds.c
+++ b/board/freescale/ls1046aqds/ls1046aqds.c
@@ -120,6 +120,13 @@ unsigned long get_board_ddr_clk(void)
 	return 66666666;
 }
 
+#ifdef CONFIG_LPUART
+u32 get_lpuart_clk(void)
+{
+	return gd->bus_clk;
+}
+#endif
+
 int select_i2c_ch_pca9547(u8 ch)
 {
 	int ret;
@@ -157,6 +164,9 @@ int board_early_init_f(void)
 	struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR;
 	u32 usb_pwrfault;
 #endif
+#ifdef CONFIG_LPUART
+	u8 uart;
+#endif
 
 #ifdef CONFIG_SYS_I2C_EARLY_INIT
 	i2c_early_init_f();
@@ -175,6 +185,14 @@ int board_early_init_f(void)
 	out_be32(&scfg->usbpwrfault_selcr, usb_pwrfault);
 #endif
 
+#ifdef CONFIG_LPUART
+	/* We use lpuart0 as system console */
+	uart = QIXIS_READ(brdcfg[14]);
+	uart &= ~CFG_UART_MUX_MASK;
+	uart |= CFG_LPUART_EN << CFG_UART_MUX_SHIFT;
+	QIXIS_WRITE(brdcfg[14], uart);
+#endif
+
 	return 0;
 }
 
diff --git a/board/freescale/ls2080a/MAINTAINERS b/board/freescale/ls2080a/MAINTAINERS
index c8dac99..de137ef 100644
--- a/board/freescale/ls2080a/MAINTAINERS
+++ b/board/freescale/ls2080a/MAINTAINERS
@@ -1,5 +1,5 @@
 LS2080A BOARD
-M:	York Sun <york.sun@nxp.com>
+M:	York Sun <york.sun@nxp.com>, Priyanka Jain <priyanka.jain@nxp.com>
 S:	Maintained
 F:	board/freescale/ls2080a/
 F:	include/configs/ls2080a_emu.h
diff --git a/board/freescale/ls2080aqds/MAINTAINERS b/board/freescale/ls2080aqds/MAINTAINERS
index 8f78b67..79877d7 100644
--- a/board/freescale/ls2080aqds/MAINTAINERS
+++ b/board/freescale/ls2080aqds/MAINTAINERS
@@ -1,5 +1,5 @@
 LS2080A BOARD
-M:	Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
+M:	Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>, Priyanka Jain <priyanka.jain@nxp.com>
 S:	Maintained
 F:	board/freescale/ls2080aqds/
 F:	board/freescale/ls2080a/ls2080aqds.c
diff --git a/board/freescale/ls2080aqds/README b/board/freescale/ls2080aqds/README
index f288750..2808bd5 100644
--- a/board/freescale/ls2080aqds/README
+++ b/board/freescale/ls2080aqds/README
@@ -2,14 +2,14 @@ Overview
 --------
 The LS2080A Development System (QDS) is a high-performance computing,
 evaluation, and development platform that supports the QorIQ LS2080A
-Layerscape Architecture processor. The LS2080AQDS provides validation and
-SW development platform for the Freescale LS2080A processor series, with
-a complete debugging environment.
+and LS2088A Layerscape Architecture processor. The LS2080AQDS provides
+validation and SW development platform for the Freescale LS2080A, LS2088A
+processor series, with a complete debugging environment.
 
-LS2080A SoC Overview
+LS2080A, LS2088A SoC Overview
 --------------------
-Please refer arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc for LS2080A
-SoC overview.
+Please refer arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc for LS2080A,
+LS2088A SoC overview.
 
  LS2080AQDS board Overview
  -----------------------
diff --git a/board/freescale/ls2080aqds/eth.c b/board/freescale/ls2080aqds/eth.c
index 95ff68b..59361e9 100644
--- a/board/freescale/ls2080aqds/eth.c
+++ b/board/freescale/ls2080aqds/eth.c
@@ -64,7 +64,7 @@ static int sgmii_riser_phy_addr[] = {
 };
 
 /* Slot2 does not have EMI connections */
-#define EMI_NONE	0xFFFFFFFF
+#define EMI_NONE	0xFF
 #define EMI1_SLOT1	0
 #define EMI1_SLOT2	1
 #define EMI1_SLOT3	2
@@ -144,8 +144,10 @@ static void sgmii_configure_repeater(int serdes_port)
 
 		mdelay(10);
 
-		if ((value & 0xfff) == 0x40f) {
+		if ((value & 0xfff) == 0x401) {
 			printf("DPMAC %d:PHY is ..... Configured\n", dpmac_id);
+			miiphy_write(dev[mii_bus], riser_phy_addr[dpmac],
+				     0x1f, 0);
 			continue;
 		}
 
@@ -181,28 +183,29 @@ static void sgmii_configure_repeater(int serdes_port)
 				if (ret > 0)
 					goto error;
 
-				mdelay(1);
+				mdelay(100);
 				ret = miiphy_read(dev[mii_bus],
 						  riser_phy_addr[dpmac],
 						  0x11, &value);
 				if (ret > 0)
 					goto error;
-				mdelay(10);
 
-				if ((value & 0xfff) == 0x40f) {
+				if ((value & 0xfff) == 0x401) {
 					printf("DPMAC %d :PHY is configured ",
 					       dpmac_id);
 					printf("after setting repeater 0x%x\n",
 					       value);
 					i = 5;
 					j = 5;
-				} else
+				} else {
 					printf("DPMAC %d :PHY is failed to ",
 					       dpmac_id);
 					printf("configure the repeater 0x%x\n",
 					       value);
 				}
+			}
 		}
+		miiphy_write(dev[mii_bus], riser_phy_addr[dpmac], 0x1f, 0);
 	}
 error:
 	if (ret)
@@ -470,7 +473,49 @@ static void initialize_dpmac_to_slot(void)
 		}
 		break;
 
+	case 0x39:
+		printf("qds: WRIOP: Supported SerDes1 Protocol 0x%02x\n",
+		       serdes1_prtcl);
+		if (hwconfig_f("xqsgmii", env_hwconfig)) {
+			lane_to_slot_fsm1[0] = EMI1_SLOT3;
+			lane_to_slot_fsm1[1] = EMI1_SLOT3;
+			lane_to_slot_fsm1[2] = EMI1_SLOT3;
+			lane_to_slot_fsm1[3] = EMI_NONE;
+		} else {
+			lane_to_slot_fsm1[0] = EMI_NONE;
+			lane_to_slot_fsm1[1] = EMI_NONE;
+			lane_to_slot_fsm1[2] = EMI_NONE;
+			lane_to_slot_fsm1[3] = EMI_NONE;
+		}
+		lane_to_slot_fsm1[4] = EMI1_SLOT3;
+		lane_to_slot_fsm1[5] = EMI1_SLOT3;
+		lane_to_slot_fsm1[6] = EMI1_SLOT3;
+		lane_to_slot_fsm1[7] = EMI_NONE;
+		break;
+
+	case 0x4D:
+		printf("qds: WRIOP: Supported SerDes1 Protocol 0x%02x\n",
+		       serdes1_prtcl);
+		if (hwconfig_f("xqsgmii", env_hwconfig)) {
+			lane_to_slot_fsm1[0] = EMI1_SLOT3;
+			lane_to_slot_fsm1[1] = EMI1_SLOT3;
+			lane_to_slot_fsm1[2] = EMI_NONE;
+			lane_to_slot_fsm1[3] = EMI_NONE;
+		} else {
+			lane_to_slot_fsm1[0] = EMI_NONE;
+			lane_to_slot_fsm1[1] = EMI_NONE;
+			lane_to_slot_fsm1[2] = EMI_NONE;
+			lane_to_slot_fsm1[3] = EMI_NONE;
+		}
+		lane_to_slot_fsm1[4] = EMI1_SLOT3;
+		lane_to_slot_fsm1[5] = EMI1_SLOT3;
+		lane_to_slot_fsm1[6] = EMI_NONE;
+		lane_to_slot_fsm1[7] = EMI_NONE;
+		break;
+
 	case 0x2A:
+	case 0x4B:
+	case 0x4C:
 		printf("qds: WRIOP: Supported SerDes1 Protocol 0x%02x\n",
 		       serdes1_prtcl);
 		break;
@@ -505,6 +550,38 @@ static void initialize_dpmac_to_slot(void)
 			lane_to_slot_fsm2[7] = EMI1_SLOT6;
 		}
 		break;
+
+	case 0x47:
+		printf("qds: WRIOP: Supported SerDes2 Protocol 0x%02x\n",
+		       serdes2_prtcl);
+		lane_to_slot_fsm2[0] = EMI_NONE;
+		lane_to_slot_fsm2[1] = EMI1_SLOT5;
+		lane_to_slot_fsm2[2] = EMI1_SLOT5;
+		lane_to_slot_fsm2[3] = EMI1_SLOT5;
+
+		if (hwconfig_f("xqsgmii", env_hwconfig)) {
+			lane_to_slot_fsm2[4] = EMI_NONE;
+			lane_to_slot_fsm2[5] = EMI1_SLOT5;
+			lane_to_slot_fsm2[6] = EMI1_SLOT5;
+			lane_to_slot_fsm2[7] = EMI1_SLOT5;
+		}
+		break;
+
+	case 0x57:
+		printf("qds: WRIOP: Supported SerDes2 Protocol 0x%02x\n",
+		       serdes2_prtcl);
+		if (hwconfig_f("xqsgmii", env_hwconfig)) {
+			lane_to_slot_fsm2[0] = EMI_NONE;
+			lane_to_slot_fsm2[1] = EMI_NONE;
+			lane_to_slot_fsm2[2] = EMI_NONE;
+			lane_to_slot_fsm2[3] = EMI_NONE;
+		}
+		lane_to_slot_fsm2[4] = EMI_NONE;
+		lane_to_slot_fsm2[5] = EMI_NONE;
+		lane_to_slot_fsm2[6] = EMI1_SLOT5;
+		lane_to_slot_fsm2[7] = EMI1_SLOT5;
+		break;
+
 	default:
 		printf(" %s qds: WRIOP: Unsupported SerDes2 Protocol 0x%02x\n",
 		       __func__ , serdes2_prtcl);
@@ -537,8 +614,10 @@ void ls2080a_handle_phy_interface_sgmii(int dpmac_id)
 
 	switch (serdes1_prtcl) {
 	case 0x07:
+	case 0x39:
+	case 0x4D:
+		lane = serdes_get_first_lane(FSL_SRDS_1, SGMII1 + dpmac_id - 1);
 
-		lane = serdes_get_first_lane(FSL_SRDS_1, SGMII1 + dpmac_id);
 		slot = lane_to_slot_fsm1[lane];
 
 		switch (++slot) {
@@ -559,6 +638,26 @@ void ls2080a_handle_phy_interface_sgmii(int dpmac_id)
 			wriop_set_mdio(dpmac_id, bus);
 			break;
 		case 3:
+			if (slot == EMI_NONE)
+				return;
+			if (serdes1_prtcl == 0x39) {
+				wriop_set_phy_address(dpmac_id,
+					riser_phy_addr[dpmac_id - 2]);
+				if (dpmac_id >= 6 && hwconfig_f("xqsgmii",
+								env_hwconfig))
+					wriop_set_phy_address(dpmac_id,
+						riser_phy_addr[dpmac_id - 3]);
+			} else {
+				wriop_set_phy_address(dpmac_id,
+					riser_phy_addr[dpmac_id - 2]);
+				if (dpmac_id >= 7 && hwconfig_f("xqsgmii",
+								env_hwconfig))
+					wriop_set_phy_address(dpmac_id,
+						riser_phy_addr[dpmac_id - 3]);
+			}
+			dpmac_info[dpmac_id].board_mux = EMI1_SLOT3;
+			bus = mii_dev_for_muxval(EMI1_SLOT3);
+			wriop_set_mdio(dpmac_id, bus);
 			break;
 		case 4:
 			break;
@@ -579,6 +678,8 @@ serdes2:
 	case 0x07:
 	case 0x08:
 	case 0x49:
+	case 0x47:
+	case 0x57:
 		lane = serdes_get_first_lane(FSL_SRDS_2, SGMII9 +
 							(dpmac_id - 9));
 		slot = lane_to_slot_fsm2[lane];
@@ -597,7 +698,23 @@ serdes2:
 			wriop_set_mdio(dpmac_id, bus);
 		break;
 		case 5:
-		break;
+			if (slot == EMI_NONE)
+				return;
+			if (serdes2_prtcl == 0x47) {
+				wriop_set_phy_address(dpmac_id,
+					      riser_phy_addr[dpmac_id - 10]);
+				if (dpmac_id >= 14 && hwconfig_f("xqsgmii",
+								 env_hwconfig))
+					wriop_set_phy_address(dpmac_id,
+						riser_phy_addr[dpmac_id - 11]);
+			} else {
+				wriop_set_phy_address(dpmac_id,
+					riser_phy_addr[dpmac_id - 11]);
+			}
+			dpmac_info[dpmac_id].board_mux = EMI1_SLOT5;
+			bus = mii_dev_for_muxval(EMI1_SLOT5);
+			wriop_set_mdio(dpmac_id, bus);
+			break;
 		case 6:
 			/* Slot housing a SGMII riser card? */
 			wriop_set_phy_address(dpmac_id,
@@ -691,6 +808,8 @@ void ls2080a_handle_phy_interface_xsgmii(int i)
 
 	switch (serdes1_prtcl) {
 	case 0x2A:
+	case 0x4B:
+	case 0x4C:
 		/*
 		 * XFI does not need a PHY to work, but to avoid U-Boot use
 		 * default PHY address which is zero to a MAC when it found
diff --git a/board/freescale/ls2080ardb/MAINTAINERS b/board/freescale/ls2080ardb/MAINTAINERS
index a20c003..759a146 100644
--- a/board/freescale/ls2080ardb/MAINTAINERS
+++ b/board/freescale/ls2080ardb/MAINTAINERS
@@ -1,5 +1,5 @@
 LS2080A BOARD
-M:	Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
+M:	Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>, Priyanka Jain <priyanka.jain@nxp.com>
 S:	Maintained
 F:	board/freescale/ls2080ardb/
 F:	board/freescale/ls2080a/ls2080ardb.c
diff --git a/board/freescale/ls2080ardb/README b/board/freescale/ls2080ardb/README
index b1613ba..0c9c574 100644
--- a/board/freescale/ls2080ardb/README
+++ b/board/freescale/ls2080ardb/README
@@ -1,13 +1,13 @@
 Overview
 --------
 The LS2080A Reference Design (RDB) is a high-performance computing,
-evaluation, and development platform that supports the QorIQ LS2080A
+evaluation, and development platform that supports the QorIQ LS2080A, LS2088A
 Layerscape Architecture processor.
 
-LS2080A SoC Overview
+LS2080A, LS2088A SoC Overview
 --------------------
-Please refer arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc for LS2080A
-SoC overview.
+Please refer arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc for LS2080A,
+LS2088A SoC overview.
 
  LS2080ARDB board Overview
  -----------------------