diff options
author | Mingkai Hu <Mingkai.hu@freescale.com> | 2011-07-07 04:29:15 (GMT) |
---|---|---|
committer | Kumar Gala <galak@kernel.crashing.org> | 2011-07-17 16:03:36 (GMT) |
commit | 4f1d1b7d1e647b4e0ffd9b9feedd02110d078bdb (patch) | |
tree | cf8a0add8b61e08bcf0d5d5c2d039ed2d9ffb486 /doc | |
parent | c518fc028189699c1b169f524be60b990b88cb28 (diff) | |
download | u-boot-fsl-qoriq-4f1d1b7d1e647b4e0ffd9b9feedd02110d078bdb.tar.xz |
powerpc/p2041rdb: Add p2041rdb board support
P2041RDB Specification:
-----------------------
Memory subsystem:
* 4Gbyte unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
* 128 Mbyte NOR flash single-chip memory
* 256 Kbit M24256 I2C EEPROM
* 16 Mbyte SPI memory
* SD connector to interface with the SD memory card
Ethernet:
* dTSEC1: connected to the Vitesse SGMII PHY (VSC8221)
* dTSEC2: connected to the Vitesse SGMII PHY (VSC8221)
* dTSEC3: connected to the Vitesse SGMII PHY (VSC8221)
* dTSEC4: connected to the Vitesse RGMII PHY (VSC8641)
* dTSEC5: connected to the Vitesse RGMII PHY (VSC8641)
PCIe:
* Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT1
* Lanes C and Land D of Bank2 are connected to one x4 PCIe SLOT2
SATA: Lanes C and Land D of Bank2 are connected to two SATA connectors
USB 2.0: connected via a internal UTMI PHY to two TYPE-A interfaces
I2C:
* I2C1: Real time clock, Temperature sensor, Memory module
* I2C2: Vcore Regulator, 256Kbit I2C Bus EEPROM, PCIe slot1/2
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Diffstat (limited to 'doc')
-rw-r--r-- | doc/README.p2041rdb | 123 |
1 files changed, 123 insertions, 0 deletions
diff --git a/doc/README.p2041rdb b/doc/README.p2041rdb new file mode 100644 index 0000000..292d0d3 --- /dev/null +++ b/doc/README.p2041rdb @@ -0,0 +1,123 @@ +Overview +========= +The P2041 Processor combines four Power Architecture processor cores +with high-performance datapath acceleration architecture(DPAA), CoreNet +fabric infrastructure, as well as network and peripheral bus interfaces +required for networking, telecom/datacom, wireless infrastructure, and +military/aerospace applications. + +P2041RDB board is a quad core platform supporting the P2041 processor +of QorIQ DPAA series. + +Boot from NOR flash +=================== +1. Build image + make P2041RDB_config + make all + +2. Program image + => tftp 1000000 u-boot.bin + => protect off all + => erase eff80000 efffffff + => cp.b 1000000 eff80000 80000 + +3. Program RCW + => tftp 1000000 rcw.bin + => protect off all + => erase e8000000 e801ffff + => cp.b 1000000 e8000000 50 + +4. Program FMAN Firmware ucode + => tftp 1000000 ucode.bin + => protect off all + => erase ef000000 ef0fffff + => cp.b 1000000 ef000000 2000 + +5. Change DIP-switch + SW1[1-5] = 10110 + Note: 1 stands for 'on', 0 stands for 'off' + +Boot from SDCard +=================== +1. Build image + make P2041RDB_SDCARD_config + make all + +2. Generate PBL imge + Use PE tool to produce a image used to be programed to + SDCard which contains RCW and U-Boot image. + +3. Program the PBL image to SDCard + => tftp 1000000 pbl_sd.bin + => mmcinfo + => mmc write 1000000 8 441 + +4. Program FMAN Firmware ucode + => tftp 1000000 ucode.bin + => mmc write 1000000 46a 10 + +5. Change DIP-switch + SW1[1-5] = 01100 + Note: 1 stands for 'on', 0 stands for 'off' + +Boot from SPI flash +=================== +1. Build image + make P2041RDB_SPIFLASH_config + make all + +2. Generate PBL imge + Use PE tool to produce a image used to be programed to + SPI flash which contains RCW and U-Boot image. + +3. Program the PBL image to SPI flash + => tftp 1000000 pbl_spi.bin + => spi probe 0 + => sf erase 0 100000 + => sf write 1000000 0 $filesize + +4. Program FMAN Firmware ucode + => tftp 1000000 ucode.bin + => sf erase 110000 10000 + => sf write 1000000 110000 $filesize + +5. Change DIP-switch + SW1[1-5] = 10100 + Note: 1 stands for 'on', 0 stands for 'off' + +CPLD command +============ +The CPLD is used to control the power sequence and some serdes lane +mux function. + +cpld reset - hard reset to default bank +cpld reset altbank - reset to alternate bank +cpld lane_mux <lane> <mux_value> - set multiplexed lane pin + lane 6: 0 -> slot1 (Default) + 1 -> SGMII + lane a: 0 -> slot2 (Default) + 1 -> AURORA + lane c: 0 -> slot2 (Default) + 1 -> SATA0 + lane d: 0 -> slot2 (Default) + 1 -> SATA1 + +Using the Device Tree Source File +================================= +To create the DTB (Device Tree Binary) image file, use a command +similar to this: + dtc -O dtb -b 0 -p 1024 p2041rdb.dts > p2041rdb.dtb + +Or use the following command: + {linux-2.6}/make p2041rdb.dtb ARCH=powerpc + +then the dtb file will be generated under the following directory: + {linux-2.6}/arch/powerpc/boot/p2041rdb.dtb + +Booting Linux +============= +Place a linux uImage in the TFTP disk area. + tftp 1000000 uImage + tftp 2000000 rootfs.ext2.gz.uboot + tftp 3000000 p2041rdb.dtb + bootm 1000000 2000000 3000000 |