SPARC: Remove

The SPARC architecture is currently unmaintained, remove.

Cc: Francois Retief <fgretief@spaceteq.co.za>
Signed-off-by: Tom Rini <trini@konsulko.com>

5 files changed, 0 insertions, 1510 deletions

diff --git a/include/configs/gr_cpci_ax2000.h b/include/configs/gr_cpci_ax2000.h
deleted file mode 100644
index 2c8adab..0000000
--- a/include/configs/gr_cpci_ax2000.h
+++ /dev/null
@@ -1,339 +0,0 @@
-/* Configuration header file for Gaisler GR-CPCI-AX2000
- * AX board. Note that since the AX is removable the configuration
- * for this board must be edited below.
- *
- * (C) Copyright 2003-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2008
- * Daniel Hellstrom, Gaisler Research, daniel@gaisler.com.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __CONFIG_H__
-#define __CONFIG_H__
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_CPCI_AX2000	1	/* ... on GR-CPCI-AX2000 board */
-
-#define CONFIG_LEON_RAM_SRAM 1
-#define CONFIG_LEON_RAM_SDRAM 2
-#define CONFIG_LEON_RAM_SDRAM_NOSRAM 3
-
-/* Select Memory to run from
- *
- * SRAM          - UBoot is run in SRAM, SRAM-0x40000000, SDRAM-0x60000000
- * SDRAM         - UBoot is run in SDRAM, SRAM-0x40000000 and SDRAM-0x60000000
- * SDRAM_NOSRAM  - UBoot is run in SDRAM, SRAM not available, SDRAM at 0x40000000
- *
- * Note, if Linux is to be used, SDRAM or SDRAM_NOSRAM is required since
- * it doesn't fit into the 4Mb SRAM.
- *
- * SRAM is default since it will work for all systems, however will not
- * be able to boot linux.
- */
-#define CONFIG_LEON_RAM_SELECT CONFIG_LEON_RAM_SRAM
-
-/* CPU / AMBA BUS configuration */
-#define CONFIG_SYS_CLK_FREQ	20000000	/* 20MHz */
-
-/*
- * Serial console configuration
- */
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
-
-/* Partitions */
-
-/*
- * Supported commands
- */
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_IRQ
-
-/*
- * Autobooting
- */
-
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define	CONFIG_EXTRA_ENV_SETTINGS_BASE					\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs console=ttyS0,38400 root=/dev/nfs rw "	\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs console=ttyS0,${baudrate} root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"flash_nfs=run nfsargs addip;"					\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip;"					\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"getkernel=tftpboot $(scratch) $(bootfile)\0" \
-	"bootargs=console=ttyS0,38400 root=/dev/nfs rw nfsroot=192.168.0.20:/export/rootfs ip=192.168.0.206:192.168.0.20:192.168.0.1:255.255.255.0:ax2000:eth0\0"
-
-#if CONFIG_LEON_RAM_SELECT == CONFIG_LEON_RAM_SRAM
-#define CONFIG_EXTRA_ENV_SETTINGS_SELECT \
-	"net_nfs=tftp 40000000 ${bootfile};run nfsargs addip;bootm\0"	\
-	"scratch=40200000\0"					\
-	""
-#elif CONFIG_LEON_RAM_SELECT == CONFIG_LEON_RAM_SDRAM
-#define CONFIG_EXTRA_ENV_SETTINGS_SELECT \
-	"net_nfs=tftp 60000000 ${bootfile};run nfsargs addip;bootm\0"	\
-	"scratch=60800000\0"					\
-	""
-#else
-/* More than 4Mb is assumed when running from SDRAM */
-#define CONFIG_EXTRA_ENV_SETTINGS_SELECT \
-	"net_nfs=tftp 40000000 ${bootfile};run nfsargs addip;bootm\0"	\
-	"scratch=40800000\0"					\
-	""
-#endif
-
-#define	CONFIG_EXTRA_ENV_SETTINGS CONFIG_EXTRA_ENV_SETTINGS_BASE CONFIG_EXTRA_ENV_SETTINGS_SELECT
-
-#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_GATEWAYIP 192.168.0.1
-#define CONFIG_SERVERIP 192.168.0.20
-#define CONFIG_IPADDR 192.168.0.206
-#define CONFIG_ROOTPATH "/export/rootfs"
-#define CONFIG_HOSTNAME  ax2000
-#define CONFIG_BOOTFILE "/uImage"
-
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-/* Memory MAP
- *
- *  Flash:
- *  |--------------------------------|
- *  | 0x00000000 Text & Data & BSS   | *
- *  |            for Monitor         | *
- *  | ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~| *
- *  | UNUSED / Growth                | * 256kb
- *  |--------------------------------|
- *  | 0x00050000 Base custom area    | *
- *  |            kernel / FS         | *
- *  |                                | * Rest of Flash
- *  |~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~|
- *  | END-0x00008000 Environment     | * 32kb
- *  |--------------------------------|
- *
- *
- *
- *  Main Memory (4Mb SRAM or XMb SDRAM):
- *  |--------------------------------|
- *  | UNUSED / scratch area          |
- *  |                                |
- *  |                                |
- *  |                                |
- *  |                                |
- *  |--------------------------------|
- *  | Monitor .Text / .DATA / .BSS   | * 256kb
- *  | Relocated!                     | *
- *  |--------------------------------|
- *  | Monitor Malloc                 | * 128kb (contains relocated environment)
- *  |--------------------------------|
- *  | Monitor/kernel STACK           | * 64kb
- *  |--------------------------------|
- *  | Page Table for MMU systems     | * 2k
- *  |--------------------------------|
- *  | PROM Code accessed from Linux  | * 6kb-128b
- *  |--------------------------------|
- *  | Global data (avail from kernel)| * 128b
- *  |--------------------------------|
- *
- */
-
-/*
- * Flash configuration (8,16 or 32 MB)
- * TEXT base always at 0xFFF00000
- * ENV_ADDR always at  0xFFF40000
- * FLASH_BASE at 0xFC000000 for 64 MB
- *               0xFE000000 for 32 MB
- *               0xFF000000 for 16 MB
- *               0xFF800000 for  8 MB
- */
-#define CONFIG_SYS_FLASH_BASE		0x00000000
-#define CONFIG_SYS_FLASH_SIZE		0x00800000
-
-#define PHYS_FLASH_SECT_SIZE	0x00020000	/* 128 KB sectors */
-#define CONFIG_SYS_MAX_FLASH_SECT	64	/* max num of sects on one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of memory banks      */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	240000	/* Flash Erase Timeout (in ms)  */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)  */
-#define CONFIG_SYS_FLASH_LOCK_TOUT	5	/* Timeout for Flash Set Lock Bit (in ms) */
-#define CONFIG_SYS_FLASH_UNLOCK_TOUT	10000	/* Timeout for Flash Clear Lock Bits (in ms) */
-#define CONFIG_SYS_FLASH_PROTECTION	/* "Real" (hardware) sectors protection */
-
-/*** CFI CONFIG ***/
-#define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_8BIT
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-/* Bypass cache when reading regs from flash memory */
-#define CONFIG_SYS_FLASH_CFI_BYPASS_READ
-/* Buffered writes (32byte/go) instead of single accesses */
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-
-/*
- * Environment settings
- */
-/*#define CONFIG_ENV_IS_NOWHERE 1*/
-#define CONFIG_ENV_IS_IN_FLASH	1
-/* CONFIG_ENV_ADDR need to be at sector boundary */
-#define CONFIG_ENV_SIZE		0x8000
-#define CONFIG_ENV_SECT_SIZE	0x20000
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE+CONFIG_SYS_FLASH_SIZE-CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_OVERWRITE	1
-
-/*
- * Memory map
- *
- * Always 4Mb SRAM available
- * SDRAM module may be available on 0x60000000, SDRAM
- * is configured as if a 128Mb SDRAM module is available.
- */
-
-#if CONFIG_LEON_RAM_SELECT == CONFIG_LEON_RAM_SDRAM_NOSRAM
-#define CONFIG_SYS_SDRAM_BASE		0x40000000
-#else
-#define CONFIG_SYS_SDRAM_BASE		0x60000000
-#endif
-
-#define CONFIG_SYS_SDRAM_SIZE		0x08000000
-#define CONFIG_SYS_SDRAM_END		(CONFIG_SYS_SDRAM_BASE+CONFIG_SYS_SDRAM_SIZE)
-
-/* 4Mb SRAM available */
-#if CONFIG_LEON_RAM_SELECT != CONFIG_LEON_RAM_SDRAM_NOSRAM
-#define CONFIG_SYS_SRAM_BASE 0x40000000
-#define CONFIG_SYS_SRAM_SIZE 0x400000
-#define CONFIG_SYS_SRAM_END  (CONFIG_SYS_SRAM_BASE+CONFIG_SYS_SRAM_SIZE)
-#endif
-
-/* Select RAM used to run U-BOOT from... */
-#if CONFIG_LEON_RAM_SELECT == CONFIG_LEON_RAM_SRAM
-#define CONFIG_SYS_RAM_BASE CONFIG_SYS_SRAM_BASE
-#define CONFIG_SYS_RAM_SIZE CONFIG_SYS_SRAM_SIZE
-#define CONFIG_SYS_RAM_END CONFIG_SYS_SRAM_END
-#else
-#define CONFIG_SYS_RAM_BASE CONFIG_SYS_SDRAM_BASE
-#define CONFIG_SYS_RAM_SIZE CONFIG_SYS_SDRAM_SIZE
-#define CONFIG_SYS_RAM_END CONFIG_SYS_SDRAM_END
-#endif
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_RAM_END - GENERATED_GBL_DATA_SIZE)
-
-#define CONFIG_SYS_PROM_SIZE		(8192-GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_PROM_OFFSET		(CONFIG_SYS_GBL_DATA_OFFSET-CONFIG_SYS_PROM_SIZE)
-
-#define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_PROM_OFFSET-32)
-#define CONFIG_SYS_STACK_SIZE		(0x10000-32)
-
-#define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#   define CONFIG_SYS_RAMBOOT		1
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor   */
-#define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()  */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-#define CONFIG_SYS_MALLOC_END		(CONFIG_SYS_INIT_SP_OFFSET-CONFIG_SYS_STACK_SIZE)
-#define CONFIG_SYS_MALLOC_BASE		(CONFIG_SYS_MALLOC_END-CONFIG_SYS_MALLOC_LEN)
-
-/* relocated monitor area */
-#define CONFIG_SYS_RELOC_MONITOR_MAX_END   CONFIG_SYS_MALLOC_BASE
-#define CONFIG_SYS_RELOC_MONITOR_BASE     (CONFIG_SYS_RELOC_MONITOR_MAX_END-CONFIG_SYS_MONITOR_LEN)
-
-/* make un relocated address from relocated address */
-#define UN_RELOC(address) (address-(CONFIG_SYS_RELOC_MONITOR_BASE-CONFIG_SYS_TEXT_BASE))
-
-/*
- * Ethernet configuration uses on board SMC91C111
- */
-#define CONFIG_SMC91111          1
-#define CONFIG_SMC91111_BASE		0x20000300	/* chip select 3         */
-#define CONFIG_SMC_USE_32_BIT		1	/* 32 bit bus  */
-#undef  CONFIG_SMC_91111_EXT_PHY	/* we use internal phy   */
-/*#define CONFIG_SHOW_ACTIVITY*/
-#define CONFIG_NET_RETRY_COUNT		10	/* # of retries          */
-
-#define CONFIG_PHY_ADDR	 0x00
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP		/* undef to save memory     */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size  */
-#else
-#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size  */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS		16	/* max number of command args   */
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size    */
-
-#define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on */
-#define CONFIG_SYS_MEMTEST_END		0x00f00000	/* 1 ... 15 MB in DRAM  */
-
-#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
-
-/*
- * Various low-level settings
- */
-
-/*-----------------------------------------------------------------------
- * USB stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_USB_CLOCK	0x0001BBBB
-#define CONFIG_USB_CONFIG	0x00005000
-
-/***** Gaisler GRLIB IP-Cores Config ********/
-
-#define CONFIG_SYS_GRLIB_SDRAM    0
-
-/* No SDRAM Configuration */
-#undef CONFIG_SYS_GRLIB_GAISLER_SDCTRL1
-
-/* See, GRLIB Docs (grip.pdf) on how to set up
- * These the memory controller registers.
- */
-#define CONFIG_SYS_GRLIB_ESA_MCTRL1
-#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG1   (0x10f800ff | (1<<11))
-#if CONFIG_LEON_RAM_SELECT == CONFIG_LEON_RAM_SDRAM_NOSRAM
-#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG2   0x82206000
-#else
-#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG2   0x82205260
-#endif
-#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG3   0x0809a000
-
-/* GRLIB FT-MCTRL configuration */
-#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1
-#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG1   (0x10f800ff | (1<<11))
-#if CONFIG_LEON_RAM_SELECT == CONFIG_LEON_RAM_SDRAM_NOSRAM
-#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG2   0x82206000
-#else
-#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG2   0x82205260
-#endif
-#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG3   0x0809a000
-
-/* no DDR controller */
-#undef CONFIG_SYS_GRLIB_GAISLER_DDRSPA1
-
-/* no DDR2 Controller */
-#undef CONFIG_SYS_GRLIB_GAISLER_DDR2SPA1
-
-/* default kernel command line */
-#define CONFIG_DEFAULT_KERNEL_COMMAND_LINE "console=ttyS0,38400\0\0"
-
-#endif				/* __CONFIG_H */
diff --git a/include/configs/gr_ep2s60.h b/include/configs/gr_ep2s60.h
deleted file mode 100644
index 2edb1b0..0000000
--- a/include/configs/gr_ep2s60.h
+++ /dev/null
@@ -1,304 +0,0 @@
-/* Configuration header file for Gaisler Research AB's Template
- * design (GPL Open Source SPARC/LEON3 96MHz) for Altera NIOS
- * Development board Stratix II edition, with the FPGA device
- * EP2S60.
- *
- * (C) Copyright 2003-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2008
- * Daniel Hellstrom, Gaisler Research, daniel@gaisler.com.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __CONFIG_H__
-#define __CONFIG_H__
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-/* Altera NIOS Development board, Stratix II board */
-#define CONFIG_GR_EP2S60	1
-
-/* CPU / AMBA BUS configuration */
-#define CONFIG_SYS_CLK_FREQ	96000000	/* 96MHz */
-
-/* Define this is the GR-2S60-MEZZ mezzanine is available and you
- * want to use the USB and GRETH functionality of the board
- */
-#undef GR_2S60_MEZZ
-
-#ifdef GR_2S60_MEZZ
-#define USE_GRETH 1
-#define USE_GRUSB 1
-#endif
-
-/*
- * Serial console configuration
- */
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
-
-/* Partitions */
-
-/*
- * Supported commands
- */
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_IRQ
-
-/* USB support */
-#if USE_GRUSB
-#define CONFIG_USB_UHCI
-/* Enable needed helper functions */
-#endif
-
-/*
- * Autobooting
- */
-
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs console=ttyS0,38400 root=/dev/nfs rw "	\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs console=ttyS0,${baudrate} root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"flash_nfs=run nfsargs addip;"					\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip;"					\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 40000000 ${bootfile};run nfsargs addip;bootm\0"	\
-	"scratch=40800000\0"					\
-	"getkernel=tftpboot $(scratch) $(bootfile)\0" \
-	"bootargs=console=ttyS0,38400 root=/dev/nfs rw nfsroot=192.168.0.20:/export/rootfs ip=192.168.0.207:192.168.0.20:192.168.0.1:255.255.255.0:ml401:eth0\0" \
-	""
-
-#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_GATEWAYIP 192.168.0.1
-#define CONFIG_SERVERIP 192.168.0.20
-#define CONFIG_IPADDR 192.168.0.207
-#define CONFIG_ROOTPATH "/export/rootfs"
-#define CONFIG_HOSTNAME  ml401
-#define CONFIG_BOOTFILE "/uImage"
-
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-/* Memory MAP
- *
- *  Flash:
- *  |--------------------------------|
- *  | 0x00000000 Text & Data & BSS   | *
- *  |            for Monitor         | *
- *  | ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~| *
- *  | UNUSED / Growth                | * 256kb
- *  |--------------------------------|
- *  | 0x00050000 Base custom area    | *
- *  |            kernel / FS         | *
- *  |                                | * Rest of Flash
- *  |~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~|
- *  | END-0x00008000 Environment     | * 32kb
- *  |--------------------------------|
- *
- *
- *
- *  Main Memory:
- *  |--------------------------------|
- *  | UNUSED / scratch area          |
- *  |                                |
- *  |                                |
- *  |                                |
- *  |                                |
- *  |--------------------------------|
- *  | Monitor .Text / .DATA / .BSS   | * 512kb
- *  | Relocated!                     | *
- *  |--------------------------------|
- *  | Monitor Malloc                 | * 128kb (contains relocated environment)
- *  |--------------------------------|
- *  | Monitor/kernel STACK           | * 64kb
- *  |--------------------------------|
- *  | Page Table for MMU systems     | * 2k
- *  |--------------------------------|
- *  | PROM Code accessed from Linux  | * 6kb-128b
- *  |--------------------------------|
- *  | Global data (avail from kernel)| * 128b
- *  |--------------------------------|
- *
- */
-
-/*
- * Flash configuration (8,16 or 32 MB)
- * TEXT base always at 0xFFF00000
- * ENV_ADDR always at  0xFFF40000
- * FLASH_BASE at 0xFC000000 for 64 MB
- *               0xFE000000 for 32 MB
- *               0xFF000000 for 16 MB
- *               0xFF800000 for  8 MB
- */
-#define CONFIG_SYS_FLASH_BASE		0x00000000
-#define CONFIG_SYS_FLASH_SIZE		0x00400000	/* FPGA Bit file is in top of FLASH, we only ues the bottom 4Mb */
-
-#define PHYS_FLASH_SECT_SIZE	0x00010000	/* 64 KB sectors */
-#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max num of sects on one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of memory banks      */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	240000	/* Flash Erase Timeout (in ms)  */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)  */
-#define CONFIG_SYS_FLASH_LOCK_TOUT	5	/* Timeout for Flash Set Lock Bit (in ms) */
-#define CONFIG_SYS_FLASH_UNLOCK_TOUT	10000	/* Timeout for Flash Clear Lock Bits (in ms) */
-#define CONFIG_SYS_FLASH_PROTECTION	/* "Real" (hardware) sectors protection */
-
-/*** CFI CONFIG ***/
-#define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_8BIT
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-/* Bypass cache when reading regs from flash memory */
-#define CONFIG_SYS_FLASH_CFI_BYPASS_READ
-/* Buffered writes (32byte/go) instead of single accesses */
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-
-/*
- * Environment settings
- */
-/*#define CONFIG_ENV_IS_NOWHERE 1*/
-#define CONFIG_ENV_IS_IN_FLASH	1
-/* CONFIG_ENV_ADDR need to be at sector boundary */
-#define CONFIG_ENV_SIZE		0x8000
-#define CONFIG_ENV_SECT_SIZE	0x20000
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE+CONFIG_SYS_FLASH_SIZE-CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_OVERWRITE	1
-
-/*
- * Memory map
- */
-#define CONFIG_SYS_SDRAM_BASE		0x40000000
-#define CONFIG_SYS_SDRAM_SIZE		0x02000000
-#define CONFIG_SYS_SDRAM_END		(CONFIG_SYS_SDRAM_BASE+CONFIG_SYS_SDRAM_SIZE)
-
-/* no SRAM available */
-#undef CONFIG_SYS_SRAM_BASE
-#undef CONFIG_SYS_SRAM_SIZE
-
-#define CONFIG_SYS_RAM_BASE CONFIG_SYS_SDRAM_BASE
-#define CONFIG_SYS_RAM_SIZE CONFIG_SYS_SDRAM_SIZE
-#define CONFIG_SYS_RAM_END CONFIG_SYS_SDRAM_END
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_SDRAM_END - GENERATED_GBL_DATA_SIZE)
-
-#define CONFIG_SYS_PROM_SIZE		(8192-GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_PROM_OFFSET		(CONFIG_SYS_GBL_DATA_OFFSET-CONFIG_SYS_PROM_SIZE)
-
-#define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_PROM_OFFSET-32)
-#define CONFIG_SYS_STACK_SIZE		(0x10000-32)
-
-#define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#   define CONFIG_SYS_RAMBOOT		1
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN		(512 << 10)	/* Reserve 512 kB for Monitor   */
-#define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()  */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-#define CONFIG_SYS_MALLOC_END		(CONFIG_SYS_INIT_SP_OFFSET-CONFIG_SYS_STACK_SIZE)
-#define CONFIG_SYS_MALLOC_BASE		(CONFIG_SYS_MALLOC_END-CONFIG_SYS_MALLOC_LEN)
-
-/* relocated monitor area */
-#define CONFIG_SYS_RELOC_MONITOR_MAX_END   CONFIG_SYS_MALLOC_BASE
-#define CONFIG_SYS_RELOC_MONITOR_BASE     (CONFIG_SYS_RELOC_MONITOR_MAX_END-CONFIG_SYS_MONITOR_LEN)
-
-/* make un relocated address from relocated address */
-#define UN_RELOC(address) (address-(CONFIG_SYS_RELOC_MONITOR_BASE-CONFIG_SYS_TEXT_BASE))
-
-/*
- * Ethernet configuration uses on board SMC91C111, however if a mezzanine
- * with a PHY is attached the GRETH can be used on this board.
- * Define USE_GRETH in order to use the mezzanine provided PHY with the
- * onchip GRETH network MAC, note that this is not supported by the
- * template design.
- */
-#ifndef USE_GRETH
-
-/* USE SMC91C111 MAC */
-#define CONFIG_SMC91111          1
-#define CONFIG_SMC91111_BASE		0x20000300	/* chip select 3         */
-#define CONFIG_SMC_USE_32_BIT		1	/* 32 bit bus  */
-#undef  CONFIG_SMC_91111_EXT_PHY	/* we use internal phy   */
-/*#define CONFIG_SHOW_ACTIVITY*/
-#define CONFIG_NET_RETRY_COUNT		10	/* # of retries          */
-
-#else
-
-/* USE GRETH Ethernet Driver */
-#define CONFIG_GRETH	1
-#endif
-
-#define CONFIG_PHY_ADDR	 0x00
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP		/* undef to save memory     */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size  */
-#else
-#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size  */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS		16	/* max number of command args   */
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size    */
-
-#define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on */
-#define CONFIG_SYS_MEMTEST_END		0x00f00000	/* 1 ... 15 MB in DRAM  */
-
-#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
-
-/*-----------------------------------------------------------------------
- * USB stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_USB_CLOCK	0x0001BBBB
-#define CONFIG_USB_CONFIG	0x00005000
-
-/***** Gaisler GRLIB IP-Cores Config ********/
-
-#define CONFIG_SYS_GRLIB_SDRAM    0
-
-/* No SDRAM Configuration */
-#undef CONFIG_SYS_GRLIB_GAISLER_SDCTRL1
-
-/* See, GRLIB Docs (grip.pdf) on how to set up
- * These the memory controller registers.
- */
-#define CONFIG_SYS_GRLIB_ESA_MCTRL1
-#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG1  (0x10f800ff | (1<<11))
-#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG2  0x00000000
-#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG3  0x00000000
-
-/* GRLIB FT-MCTRL configuration */
-#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1
-#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG1  (0x10f800ff | (1<<11))
-#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG2  0x00000000
-#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG3  0x00000000
-
-/* DDR controller */
-#define CONFIG_SYS_GRLIB_GAISLER_DDRSPA1
-#define CONFIG_SYS_GRLIB_GAISLER_DDRSPA1_CTRL  0xa900830a
-
-/* no DDR2 Controller */
-#undef CONFIG_SYS_GRLIB_GAISLER_DDR2SPA1
-
-/* default kernel command line */
-#define CONFIG_DEFAULT_KERNEL_COMMAND_LINE "console=ttyS0,38400\0\0"
-
-#endif				/* __CONFIG_H */
diff --git a/include/configs/gr_xc3s_1500.h b/include/configs/gr_xc3s_1500.h
deleted file mode 100644
index b8ac7d1..0000000
--- a/include/configs/gr_xc3s_1500.h
+++ /dev/null
@@ -1,271 +0,0 @@
-/* Configuration header file for Gaisler GR-XC3S-1500
- * spartan board.
- *
- * (C) Copyright 2003-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2007
- * Daniel Hellstrom, Gaisler Research, daniel@gaisler.com.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __CONFIG_H__
-#define __CONFIG_H__
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_GRXC3S1500	1	/* ... on GR-XC3S-1500 board */
-
-/* CPU / AMBA BUS configuration */
-#define CONFIG_SYS_CLK_FREQ	40000000	/* 40MHz */
-
-/*
- * Serial console configuration
- */
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
-
-/* Partitions */
-
-/*
- * Supported commands
- */
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_IRQ
-
-/*
- * Autobooting
- */
-
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs console=ttyS0,38400 root=/dev/nfs rw "	\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs console=ttyS0,${baudrate} root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"flash_nfs=run nfsargs addip;"					\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip;"					\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 40000000 ${bootfile};run nfsargs addip;bootm\0"	\
-	"scratch=40200000\0"					\
-	"getkernel=tftpboot $(scratch) $(bootfile)\0" \
-	"bootargs=console=ttyS0,38400 root=/dev/nfs rw nfsroot=192.168.0.20:/export/rootfs ip=192.168.0.206:192.168.0.20:192.168.0.1:255.255.255.0:grxc3s1500_daniel:eth0\0" \
-	""
-
-#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_GATEWAYIP 192.168.0.1
-#define CONFIG_SERVERIP 192.168.0.20
-#define CONFIG_IPADDR 192.168.0.206
-#define CONFIG_ROOTPATH "/export/rootfs"
-#define CONFIG_HOSTNAME  grxc3s1500
-#define CONFIG_BOOTFILE "/uImage"
-
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-/* Memory MAP
- *
- *  Flash:
- *  |--------------------------------|
- *  | 0x00000000 Text & Data & BSS   | *
- *  |            for Monitor         | *
- *  | ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~| *
- *  | UNUSED / Growth                | * 256kb
- *  |--------------------------------|
- *  | 0x00050000 Base custom area    | *
- *  |            kernel / FS         | *
- *  |                                | * Rest of Flash
- *  |~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~|
- *  | END-0x00008000 Environment     | * 32kb
- *  |--------------------------------|
- *
- *
- *
- *  Main Memory:
- *  |--------------------------------|
- *  | UNUSED / scratch area          |
- *  |                                |
- *  |                                |
- *  |                                |
- *  |                                |
- *  |--------------------------------|
- *  | Monitor .Text / .DATA / .BSS   | * 256kb
- *  | Relocated!                     | *
- *  |--------------------------------|
- *  | Monitor Malloc                 | * 128kb (contains relocated environment)
- *  |--------------------------------|
- *  | Monitor/kernel STACK           | * 64kb
- *  |--------------------------------|
- *  | Page Table for MMU systems     | * 2k
- *  |--------------------------------|
- *  | PROM Code accessed from Linux  | * 6kb-128b
- *  |--------------------------------|
- *  | Global data (avail from kernel)| * 128b
- *  |--------------------------------|
- *
- */
-
-/*
- * Flash configuration (8,16 or 32 MB)
- * TEXT base always at 0xFFF00000
- * ENV_ADDR always at  0xFFF40000
- * FLASH_BASE at 0xFC000000 for 64 MB
- *               0xFE000000 for 32 MB
- *               0xFF000000 for 16 MB
- *               0xFF800000 for  8 MB
- */
-#define CONFIG_SYS_FLASH_BASE		0x00000000
-#define CONFIG_SYS_FLASH_SIZE		0x00800000
-
-#define PHYS_FLASH_SECT_SIZE	0x00020000	/* 128 KB sectors */
-#define CONFIG_SYS_MAX_FLASH_SECT	64	/* max num of sects on one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of memory banks      */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	240000	/* Flash Erase Timeout (in ms)  */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)  */
-#define CONFIG_SYS_FLASH_LOCK_TOUT	5	/* Timeout for Flash Set Lock Bit (in ms) */
-#define CONFIG_SYS_FLASH_UNLOCK_TOUT	10000	/* Timeout for Flash Clear Lock Bits (in ms) */
-#define CONFIG_SYS_FLASH_PROTECTION	/* "Real" (hardware) sectors protection */
-
-/*** CFI CONFIG ***/
-#define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_8BIT
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-/* Bypass cache when reading regs from flash memory */
-#define CONFIG_SYS_FLASH_CFI_BYPASS_READ
-/* Buffered writes (32byte/go) instead of single accesses */
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-
-/*
- * Environment settings
- */
-/*#define CONFIG_ENV_IS_NOWHERE 1*/
-#define CONFIG_ENV_IS_IN_FLASH	1
-/* CONFIG_ENV_ADDR need to be at sector boundary */
-#define CONFIG_ENV_SIZE		0x8000
-#define CONFIG_ENV_SECT_SIZE	0x20000
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE+CONFIG_SYS_FLASH_SIZE-CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_OVERWRITE	1
-
-/*
- * Memory map
- */
-#define CONFIG_SYS_SDRAM_BASE		0x40000000
-#define CONFIG_SYS_SDRAM_SIZE		0x4000000
-#define CONFIG_SYS_SDRAM_END		(CONFIG_SYS_SDRAM_BASE+CONFIG_SYS_SDRAM_SIZE)
-
-/* no SRAM available */
-#undef CONFIG_SYS_SRAM_BASE
-#undef CONFIG_SYS_SRAM_SIZE
-
-/* Always Run U-Boot from SDRAM */
-#define CONFIG_SYS_RAM_BASE CONFIG_SYS_SDRAM_BASE
-#define CONFIG_SYS_RAM_SIZE CONFIG_SYS_SDRAM_SIZE
-#define CONFIG_SYS_RAM_END CONFIG_SYS_SDRAM_END
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_RAM_END - GENERATED_GBL_DATA_SIZE)
-
-#define CONFIG_SYS_PROM_SIZE		(8192-GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_PROM_OFFSET		(CONFIG_SYS_GBL_DATA_OFFSET-CONFIG_SYS_PROM_SIZE)
-
-#define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_PROM_OFFSET-32)
-#define CONFIG_SYS_STACK_SIZE		(0x10000-32)
-
-#define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#   define CONFIG_SYS_RAMBOOT		1
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor   */
-#define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()  */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-#define CONFIG_SYS_MALLOC_END		(CONFIG_SYS_INIT_SP_OFFSET-CONFIG_SYS_STACK_SIZE)
-#define CONFIG_SYS_MALLOC_BASE		(CONFIG_SYS_MALLOC_END-CONFIG_SYS_MALLOC_LEN)
-
-/* relocated monitor area */
-#define CONFIG_SYS_RELOC_MONITOR_MAX_END   CONFIG_SYS_MALLOC_BASE
-#define CONFIG_SYS_RELOC_MONITOR_BASE     (CONFIG_SYS_RELOC_MONITOR_MAX_END-CONFIG_SYS_MONITOR_LEN)
-
-/* make un relocated address from relocated address */
-#define UN_RELOC(address) (address-(CONFIG_SYS_RELOC_MONITOR_BASE-CONFIG_SYS_TEXT_BASE))
-
-/*
- * Ethernet configuration
- */
-#define CONFIG_GRETH	1
-
-#define CONFIG_PHY_ADDR	 0x00
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP		/* undef to save memory     */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size  */
-#else
-#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size  */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS		16	/* max number of command args   */
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size    */
-
-#define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on */
-#define CONFIG_SYS_MEMTEST_END		0x00f00000	/* 1 ... 15 MB in DRAM  */
-
-#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
-
-/*
- * Various low-level settings
- */
-
-/*-----------------------------------------------------------------------
- * USB stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_USB_CLOCK	0x0001BBBB
-#define CONFIG_USB_CONFIG	0x00005000
-
-/***** Gaisler GRLIB IP-Cores Config ********/
-
-#define CONFIG_SYS_GRLIB_SDRAM    0
-
-/* No SDRAM Configuration */
-#undef CONFIG_SYS_GRLIB_GAISLER_SDCTRL1
-
-/* See, GRLIB Docs (grip.pdf) on how to set up
- * These the memory controller registers.
- */
-#define CONFIG_SYS_GRLIB_ESA_MCTRL1
-#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG1   (0x000000ff | (1<<11))
-#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG2   0x82206000
-#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG3   0x00136000
-
-/* GRLIB FT-MCTRL configuration */
-#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1
-#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG1   (0x000000ff | (1<<11))
-#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG2   0x82206000
-#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG3   0x00136000
-
-/* no DDR controller */
-#undef CONFIG_SYS_GRLIB_GAISLER_DDRSPA1
-
-/* no DDR2 Controller */
-#undef CONFIG_SYS_GRLIB_GAISLER_DDR2SPA1
-
-/* default kernel command line */
-#define CONFIG_DEFAULT_KERNEL_COMMAND_LINE "console=ttyS0,38400\0\0"
-
-#endif				/* __CONFIG_H */
diff --git a/include/configs/grsim.h b/include/configs/grsim.h
deleted file mode 100644
index 4594b13..0000000
--- a/include/configs/grsim.h
+++ /dev/null
@@ -1,313 +0,0 @@
-/* Configuration header file for LEON3 GRSIM, trying to be similar
- * to Gaisler's GR-XC3S-1500 board.
- *
- * (C) Copyright 2003-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2007
- * Daniel Hellstrom, Gaisler Research, daniel@gaisler.com.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __CONFIG_H__
-#define __CONFIG_H__
-
-/*
- * High Level Configuration Options
- * (easy to change)
- *
- * Select between TSIM or GRSIM by setting CONFIG_GRSIM or CONFIG_TSIM to 1.
- *
- * TSIM command:
- * $ tsim-leon3 -sdram 32768 -ram 4096 -rom 2048 -mmu -cas
- *
- * In the evaluation version of TSIM, the -sdram/-ram/-rom arguments are
- * hard-coded to these values and need not be specified. (see below)
- *
- * Get TSIM from http://www.gaisler.com/index.php/downloads/simulators
- */
-
-#define CONFIG_GRSIM		0	/* ... not running on GRSIM */
-#define CONFIG_TSIM		1	/* ... running on TSIM */
-
-/* CPU / AMBA BUS configuration */
-#define CONFIG_SYS_CLK_FREQ	40000000	/* 40MHz */
-
-/*
- * Serial console configuration
- */
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
-
-/* Partitions */
-
-/*
- * Supported commands
- */
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_FPGA_LOADMK
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_REGINFO
-
-/*
- * Autobooting
- */
-
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"flash_nfs=run nfsargs addip;"					\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip;"					\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 40000000 ${bootfile};run nfsargs addip;bootm\0"	\
-	"rootpath=/export/roofs\0"					\
-	"scratch=40000000\0"					\
-	"getkernel=tftpboot $(scratch) $(bootfile)\0" \
-	"bootargs=console=ttyS0,38400" \
-	""
-#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_GATEWAYIP 192.168.0.1
-#define CONFIG_SERVERIP 192.168.0.81
-#define CONFIG_IPADDR 192.168.0.80
-#define CONFIG_ROOTPATH "/export/rootfs"
-#define CONFIG_HOSTNAME  grxc3s1500
-#define CONFIG_BOOTFILE "/uImage"
-
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-/* Memory MAP
- *
- *  Flash:
- *  |--------------------------------|
- *  | 0x00000000 Text & Data & BSS   | *
- *  |            for Monitor         | *
- *  | ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~| *
- *  | UNUSED / Growth                | * 256kb
- *  |--------------------------------|
- *  | 0x00050000 Base custom area    | *
- *  |            kernel / FS         | *
- *  |                                | * Rest of Flash
- *  |~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~|
- *  | END-0x00008000 Environment     | * 32kb
- *  |--------------------------------|
- *
- *
- *
- *  Main Memory:
- *  |--------------------------------|
- *  | UNUSED / scratch area          |
- *  |                                |
- *  |                                |
- *  |                                |
- *  |                                |
- *  |--------------------------------|
- *  | Monitor .Text / .DATA / .BSS   | * 256kb
- *  | Relocated!                     | *
- *  |--------------------------------|
- *  | Monitor Malloc                 | * 128kb (contains relocated environment)
- *  |--------------------------------|
- *  | Monitor/kernel STACK           | * 64kb
- *  |--------------------------------|
- *  | Page Table for MMU systems     | * 2k
- *  |--------------------------------|
- *  | PROM Code accessed from Linux  | * 6kb-128b
- *  |--------------------------------|
- *  | Global data (avail from kernel)| * 128b
- *  |--------------------------------|
- *
- */
-
-/*
- * Flash configuration (8,16 or 32 MB)
- * TEXT base always at 0xFFF00000
- * ENV_ADDR always at  0xFFF40000
- * FLASH_BASE at 0xFC000000 for 64 MB
- *               0xFE000000 for 32 MB
- *               0xFF000000 for 16 MB
- *               0xFF800000 for  8 MB
- */
-#define CONFIG_SYS_FLASH_BASE		0x00000000
-#define CONFIG_SYS_FLASH_SIZE		0x00800000
-#define CONFIG_ENV_SIZE		0x8000
-
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE+CONFIG_SYS_FLASH_SIZE-CONFIG_ENV_SIZE)
-
-#define PHYS_FLASH_SECT_SIZE	0x00020000	/* 128 KB sectors */
-#define CONFIG_SYS_MAX_FLASH_SECT	64	/* max num of sects on one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of memory banks      */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	240000	/* Flash Erase Timeout (in ms)  */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)  */
-#define CONFIG_SYS_FLASH_LOCK_TOUT	5	/* Timeout for Flash Set Lock Bit (in ms) */
-#define CONFIG_SYS_FLASH_UNLOCK_TOUT	10000	/* Timeout for Flash Clear Lock Bits (in ms) */
-
-#ifdef ENABLE_FLASH_SUPPORT
-/* For use with grsim FLASH emulation extension */
-#define CONFIG_SYS_FLASH_PROTECTION	/* "Real" (hardware) sectors protection */
-
-#undef CONFIG_FLASH_8BIT	/* Flash is 32-bit */
-
-/*** CFI CONFIG ***/
-#define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_8BIT
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#endif
-
-/*
- * Environment settings
- */
-#define CONFIG_ENV_IS_NOWHERE 1
-/*#define CONFIG_ENV_IS_IN_FLASH*/
-/*#define CONFIG_ENV_SIZE		0x8000*/
-#define CONFIG_ENV_SECT_SIZE	0x40000
-#define CONFIG_ENV_OVERWRITE	1
-
-/*
- * Memory map
- */
-#define CONFIG_SYS_SDRAM_BASE		0x60000000
-#define CONFIG_SYS_SDRAM_SIZE		0x02000000 /* 32MiB SDRAM */
-#define CONFIG_SYS_SDRAM_END		(CONFIG_SYS_SDRAM_BASE + CONFIG_SYS_SDRAM_SIZE)
-
-#define CONFIG_SYS_SRAM_BASE		0x40000000
-#define CONFIG_SYS_SRAM_SIZE		0x00400000 /* 4MiB SRAM */
-#define CONFIG_SYS_SRAM_END		(CONFIG_SYS_SRAM_BASE + CONFIG_SYS_SRAM_SIZE)
-
-/* Always Run U-Boot from SDRAM */
-#define CONFIG_SYS_RAM_BASE		CONFIG_SYS_SDRAM_BASE
-#define CONFIG_SYS_RAM_SIZE		CONFIG_SYS_SDRAM_SIZE
-#define CONFIG_SYS_RAM_END		CONFIG_SYS_SDRAM_END
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_RAM_END - GENERATED_GBL_DATA_SIZE)
-
-#define CONFIG_SYS_PROM_SIZE		(8192-GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_PROM_OFFSET		(CONFIG_SYS_GBL_DATA_OFFSET-CONFIG_SYS_PROM_SIZE)
-
-#define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_PROM_OFFSET-32)
-#define CONFIG_SYS_STACK_SIZE		(0x10000-32)
-
-#define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#   define CONFIG_SYS_RAMBOOT		1
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor   */
-#define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()  */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-#define CONFIG_SYS_MALLOC_END		(CONFIG_SYS_INIT_SP_OFFSET-CONFIG_SYS_STACK_SIZE)
-#define CONFIG_SYS_MALLOC_BASE		(CONFIG_SYS_MALLOC_END-CONFIG_SYS_MALLOC_LEN)
-
-/* relocated monitor area */
-#define CONFIG_SYS_RELOC_MONITOR_MAX_END   CONFIG_SYS_MALLOC_BASE
-#define CONFIG_SYS_RELOC_MONITOR_BASE     (CONFIG_SYS_RELOC_MONITOR_MAX_END-CONFIG_SYS_MONITOR_LEN)
-
-/* make un relocated address from relocated address */
-#define UN_RELOC(address) (address-(CONFIG_SYS_RELOC_MONITOR_BASE-CONFIG_SYS_TEXT_BASE))
-
-#ifdef CONFIG_CMD_NET
-/*
- * Ethernet configuration
- */
-#define CONFIG_GRETH	1
-
-/*
- * Define CONFIG_GRETH_10MBIT to force GRETH at 10Mb/s
- */
-/* #define CONFIG_GRETH_10MBIT 1 */
-#define CONFIG_PHY_ADDR		0x00
-
-#endif /* CONFIG_CMD_NET */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP		/* undef to save memory     */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size  */
-#else
-#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size  */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS		16	/* max number of command args   */
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size    */
-
-#define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on */
-#define CONFIG_SYS_MEMTEST_END		0x00f00000	/* 1 ... 15 MB in DRAM  */
-
-#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
-
-/***** Gaisler GRLIB IP-Cores Config ********/
-
-#define CONFIG_SYS_GRLIB_SDRAM     0
-
-#define CONFIG_SYS_GRLIB_MEMCFG1   (0x000000ff | (1<<11))
-
-/* No SDRAM Configuration */
-#undef CONFIG_SYS_GRLIB_GAISLER_SDCTRL1
-
-/* LEON2 MCTRL configuration */
-#define CONFIG_SYS_GRLIB_ESA_MCTRL1
-#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG1   (0x000000ff | (1<<11))
-#if CONFIG_GRSIM
-/* GRSIM configuration */
-#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG2   0x82206000
-#else
-/* TSIM configuration */
-#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG2   0x81805220
-#endif
-#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG3   0x00136000
-
-/* GRLIB FT-MCTRL configuration */
-#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1
-#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG1   (0x000000ff | (1<<11))
-#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG2   0x82206000
-#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG3   0x00136000
-
-/* no DDR controller */
-#undef CONFIG_SYS_GRLIB_GAISLER_DDRSPA1
-
-/* no DDR2 Controller */
-#undef CONFIG_SYS_GRLIB_GAISLER_DDR2SPA1
-
-/* default kernel command line */
-#define CONFIG_DEFAULT_KERNEL_COMMAND_LINE "console=ttyS0,38400\0\0"
-
-/* TSIM command:
- * $ ./tsim-leon3 -mmu -cas
- *
- *  This TSIM evaluation version will expire 2015-04-02
- *
- *
- *  TSIM/LEON3 SPARC simulator, version 2.0.35 (evaluation version)
- *
- *  Copyright (C) 2014, Aeroflex Gaisler - all rights reserved.
- *  This software may only be used with a valid license.
- *  For latest updates, go to http://www.gaisler.com/
- *  Comments or bug-reports to support@gaisler.com
- *
- * serial port A on stdin/stdout
- * allocated 4096 K SRAM memory, in 1 bank
- * allocated 32 M SDRAM memory, in 1 bank
- * allocated 2048 K ROM memory
- * icache: 1 * 4 kbytes, 16 bytes/line (4 kbytes total)
- * dcache: 1 * 4 kbytes, 16 bytes/line (4 kbytes total)
- * tsim> leon
- * 0x80000000   Memory configuration register 1   0x000002ff
- * 0x80000004   Memory configuration register 2   0x81805220
- * 0x80000008   Memory configuration register 3   0x00000000
- */
-
-#endif				/* __CONFIG_H */
diff --git a/include/configs/grsim_leon2.h b/include/configs/grsim_leon2.h
deleted file mode 100644
index ea9e3e8..0000000
--- a/include/configs/grsim_leon2.h
+++ /dev/null
@@ -1,283 +0,0 @@
-/* Configuration header file for LEON2 GRSIM.
- *
- * (C) Copyright 2003-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2007, 2015
- * Daniel Hellstrom, Cobham Gaisler, daniel@gaisler.com.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __CONFIG_H__
-#define __CONFIG_H__
-
-/*
- * High Level Configuration Options
- * (easy to change)
- *
- * Select between TSIM or GRSIM by setting CONFIG_GRSIM or CONFIG_TSIM to 1.
- *
- * TSIM command
- *  tsim-leon -sdram 0 -ram 32000 -rom 8192 -mmu
- *
- */
-
-#define CONFIG_GRSIM		0	/* ... not running on GRSIM */
-#define CONFIG_TSIM		1	/* ... running on TSIM */
-
-/* CPU / AMBA BUS configuration */
-#define CONFIG_SYS_CLK_FREQ	40000000	/* 40MHz */
-
-/*
- * Serial console configuration
- */
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
-
-/* Partitions */
-
-/*
- * Supported commands
- */
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_FPGA_LOADMK
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_REGINFO
-
-/*
- * Autobooting
- */
-
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"flash_nfs=run nfsargs addip;"					\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip;"					\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 40000000 ${bootfile};run nfsargs addip;bootm\0"	\
-	"rootpath=/export/roofs\0"					\
-	"scratch=40000000\0"					\
-	"getkernel=tftpboot $(scratch) $(bootfile)\0" \
-	"bootargs=console=ttyS0,38400" \
-	""
-#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_GATEWAYIP 192.168.0.1
-#define CONFIG_SERVERIP 192.168.0.81
-#define CONFIG_IPADDR 192.168.0.80
-#define CONFIG_ROOTPATH "/export/rootfs"
-#define CONFIG_HOSTNAME  grxc3s1500
-#define CONFIG_BOOTFILE "/uImage"
-
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-/* Memory MAP
- *
- *  Flash:
- *  |--------------------------------|
- *  | 0x00000000 Text & Data & BSS   | *
- *  |            for Monitor         | *
- *  | ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~| *
- *  | UNUSED / Growth                | * 256kb
- *  |--------------------------------|
- *  | 0x00050000 Base custom area    | *
- *  |            kernel / FS         | *
- *  |                                | * Rest of Flash
- *  |~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~|
- *  | END-0x00008000 Environment     | * 32kb
- *  |--------------------------------|
- *
- *
- *
- *  Main Memory:
- *  |--------------------------------|
- *  | UNUSED / scratch area          |
- *  |                                |
- *  |                                |
- *  |                                |
- *  |                                |
- *  |--------------------------------|
- *  | Monitor .Text / .DATA / .BSS   | * 256kb
- *  | Relocated!                     | *
- *  |--------------------------------|
- *  | Monitor Malloc                 | * 128kb (contains relocated environment)
- *  |--------------------------------|
- *  | Monitor/kernel STACK           | * 64kb
- *  |--------------------------------|
- *  | Page Table for MMU systems     | * 2k
- *  |--------------------------------|
- *  | PROM Code accessed from Linux  | * 6kb-128b
- *  |--------------------------------|
- *  | Global data (avail from kernel)| * 128b
- *  |--------------------------------|
- *
- */
-
-/*
- * Flash configuration (8,16 or 32 MB)
- * TEXT base always at 0xFFF00000
- * ENV_ADDR always at  0xFFF40000
- * FLASH_BASE at 0xFC000000 for 64 MB
- *               0xFE000000 for 32 MB
- *               0xFF000000 for 16 MB
- *               0xFF800000 for  8 MB
- */
-#define CONFIG_SYS_FLASH_BASE		0x00000000
-#define CONFIG_SYS_FLASH_SIZE		0x00800000
-#define CONFIG_ENV_SIZE		0x8000
-
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE+CONFIG_SYS_FLASH_SIZE-CONFIG_ENV_SIZE)
-
-#define PHYS_FLASH_SECT_SIZE	0x00020000	/* 128 KB sectors */
-#define CONFIG_SYS_MAX_FLASH_SECT	64	/* max num of sects on one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of memory banks      */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	240000	/* Flash Erase Timeout (in ms)  */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)  */
-#define CONFIG_SYS_FLASH_LOCK_TOUT	5	/* Timeout for Flash Set Lock Bit (in ms) */
-#define CONFIG_SYS_FLASH_UNLOCK_TOUT	10000	/* Timeout for Flash Clear Lock Bits (in ms) */
-
-#ifdef ENABLE_FLASH_SUPPORT
-/* For use with grsim FLASH emulation extension */
-#define CONFIG_SYS_FLASH_PROTECTION	/* "Real" (hardware) sectors protection */
-
-#undef CONFIG_FLASH_8BIT	/* Flash is 32-bit */
-
-/*** CFI CONFIG ***/
-#define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_8BIT
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#endif
-
-/*
- * Environment settings
- */
-#define CONFIG_ENV_IS_NOWHERE 1
-/*#define CONFIG_ENV_IS_IN_FLASH*/
-/*#define CONFIG_ENV_SIZE		0x8000*/
-#define CONFIG_ENV_SECT_SIZE	0x40000
-#define CONFIG_ENV_OVERWRITE	1
-
-/*
- * Memory map
- */
-#define CONFIG_SYS_SDRAM_BASE		0x40000000
-#define CONFIG_SYS_SDRAM_SIZE		0x00800000
-#define CONFIG_SYS_SDRAM_END		(CONFIG_SYS_SDRAM_BASE+CONFIG_SYS_SDRAM_SIZE)
-
-/* no SRAM available */
-#undef CONFIG_SYS_SRAM_BASE
-#undef CONFIG_SYS_SRAM_SIZE
-
-/* Always Run U-Boot from SDRAM */
-#define CONFIG_SYS_RAM_BASE CONFIG_SYS_SDRAM_BASE
-#define CONFIG_SYS_RAM_SIZE CONFIG_SYS_SDRAM_SIZE
-#define CONFIG_SYS_RAM_END CONFIG_SYS_SDRAM_END
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_RAM_END - GENERATED_GBL_DATA_SIZE)
-
-#define CONFIG_SYS_PROM_SIZE		(8192-GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_PROM_OFFSET		(CONFIG_SYS_GBL_DATA_OFFSET-CONFIG_SYS_PROM_SIZE)
-
-#define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_PROM_OFFSET-32)
-#define CONFIG_SYS_STACK_SIZE		(0x10000-32)
-
-#define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#   define CONFIG_SYS_RAMBOOT		1
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor   */
-#define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()  */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-#define CONFIG_SYS_MALLOC_END		(CONFIG_SYS_INIT_SP_OFFSET-CONFIG_SYS_STACK_SIZE)
-#define CONFIG_SYS_MALLOC_BASE		(CONFIG_SYS_MALLOC_END-CONFIG_SYS_MALLOC_LEN)
-
-/* relocated monitor area */
-#define CONFIG_SYS_RELOC_MONITOR_MAX_END   CONFIG_SYS_MALLOC_BASE
-#define CONFIG_SYS_RELOC_MONITOR_BASE     (CONFIG_SYS_RELOC_MONITOR_MAX_END-CONFIG_SYS_MONITOR_LEN)
-
-/* make un relocated address from relocated address */
-#define UN_RELOC(address) (address-(CONFIG_SYS_RELOC_MONITOR_BASE-CONFIG_SYS_TEXT_BASE))
-
-/*
- * Ethernet configuration
- */
-/*#define CONFIG_GRETH	1*/
-
-/*
- * Define CONFIG_GRETH_10MBIT to force GRETH at 10Mb/s
- */
-/* #define CONFIG_GRETH_10MBIT 1 */
-#define CONFIG_PHY_ADDR		0x00
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP		/* undef to save memory     */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size  */
-#else
-#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size  */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS		16	/* max number of command args   */
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size    */
-
-#define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on */
-#define CONFIG_SYS_MEMTEST_END		0x00f00000	/* 1 ... 15 MB in DRAM  */
-
-#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
-
-/***** Gaisler GRLIB IP-Cores Config ********/
-
-#define CONFIG_SYS_GRLIB_SDRAM    0
-#define CONFIG_SYS_GRLIB_MEMCFG1  (0x000000ff | (1<<11))
-#if CONFIG_GRSIM
-#define CONFIG_SYS_GRLIB_MEMCFG2  0x82206000
-#else
-#define CONFIG_SYS_GRLIB_MEMCFG2  0x00001820
-#endif
-#define CONFIG_SYS_GRLIB_MEMCFG3  0x00136000
-
-/*** LEON2 UART 1 ***/
-
-/* UART1 Define to 1 or 0 */
-#define LEON2_UART1_LOOPBACK_ENABLE 0
-#define LEON2_UART1_FLOWCTRL_ENABLE 0
-#define LEON2_UART1_PARITY_ENABLE 0
-#define LEON2_UART1_ODDPAR_ENABLE 0
-
-/*** LEON2 UART 2 ***/
-
-/* UART2 Define to 1 or 0 */
-#define LEON2_UART2_LOOPBACK_ENABLE 0
-#define LEON2_UART2_FLOWCTRL_ENABLE 0
-#define LEON2_UART2_PARITY_ENABLE 0
-#define LEON2_UART2_ODDPAR_ENABLE 0
-
-#define LEON_CONSOLE_UART1 1
-#define LEON_CONSOLE_UART2 2
-
-/* Use UART2 as console */
-#define LEON2_CONSOLE_SELECT LEON_CONSOLE_UART1
-
-/* LEON2 I/O Port */
-/*#define LEON2_IO_PORT_DIR 0x0000aa00*/
-
-/* default kernel command line */
-#define CONFIG_DEFAULT_KERNEL_COMMAND_LINE "console=ttyS0,38400\0\0"
-
-#endif				/* __CONFIG_H */