diff options
| -rw-r--r-- | arch/arm/cpu/arm926ejs/lpc32xx/devices.c | 6 | ||||
| -rw-r--r-- | arch/arm/include/asm/arch-lpc32xx/clk.h | 2 | ||||
| -rw-r--r-- | arch/arm/include/asm/arch-lpc32xx/sys_proto.h | 1 | ||||
| -rw-r--r-- | drivers/mtd/nand/Makefile | 1 | ||||
| -rw-r--r-- | drivers/mtd/nand/lpc32xx_nand_slc.c | 176 |
5 files changed, 186 insertions, 0 deletions
diff --git a/arch/arm/cpu/arm926ejs/lpc32xx/devices.c b/arch/arm/cpu/arm926ejs/lpc32xx/devices.c index 5a453e3..b0287be 100644 --- a/arch/arm/cpu/arm926ejs/lpc32xx/devices.c +++ b/arch/arm/cpu/arm926ejs/lpc32xx/devices.c @@ -54,6 +54,12 @@ void lpc32xx_mlc_nand_init(void) writel(CLK_NAND_MLC | CLK_NAND_MLC_INT, &clk->flashclk_ctrl); } +void lpc32xx_slc_nand_init(void) +{ + /* Enable SLC NAND interface */ + writel(CLK_NAND_SLC | CLK_NAND_SLC_SELECT, &clk->flashclk_ctrl); +} + void lpc32xx_i2c_init(unsigned int devnum) { /* Enable I2C interface */ diff --git a/arch/arm/include/asm/arch-lpc32xx/clk.h b/arch/arm/include/asm/arch-lpc32xx/clk.h index 9449869..010211a 100644 --- a/arch/arm/include/asm/arch-lpc32xx/clk.h +++ b/arch/arm/include/asm/arch-lpc32xx/clk.h @@ -153,7 +153,9 @@ struct clk_pm_regs { #define CLK_DMA_ENABLE (1 << 0) /* NAND Clock Control Register bits */ +#define CLK_NAND_SLC (1 << 0) #define CLK_NAND_MLC (1 << 1) +#define CLK_NAND_SLC_SELECT (1 << 2) #define CLK_NAND_MLC_INT (1 << 5) /* SSP Clock Control Register bits */ diff --git a/arch/arm/include/asm/arch-lpc32xx/sys_proto.h b/arch/arm/include/asm/arch-lpc32xx/sys_proto.h index c3d890d..0845f83 100644 --- a/arch/arm/include/asm/arch-lpc32xx/sys_proto.h +++ b/arch/arm/include/asm/arch-lpc32xx/sys_proto.h @@ -12,6 +12,7 @@ void lpc32xx_uart_init(unsigned int uart_id); void lpc32xx_mac_init(void); void lpc32xx_mlc_nand_init(void); +void lpc32xx_slc_nand_init(void); void lpc32xx_i2c_init(unsigned int devnum); void lpc32xx_ssp_init(void); #if defined(CONFIG_SPL_BUILD) diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile index b40dda8..46dce72 100644 --- a/drivers/mtd/nand/Makefile +++ b/drivers/mtd/nand/Makefile @@ -54,6 +54,7 @@ obj-$(CONFIG_NAND_KB9202) += kb9202_nand.o obj-$(CONFIG_NAND_KIRKWOOD) += kirkwood_nand.o obj-$(CONFIG_NAND_KMETER1) += kmeter1_nand.o obj-$(CONFIG_NAND_LPC32XX_MLC) += lpc32xx_nand_mlc.o +obj-$(CONFIG_NAND_LPC32XX_SLC) += lpc32xx_nand_slc.o obj-$(CONFIG_NAND_MPC5121_NFC) += mpc5121_nfc.o obj-$(CONFIG_NAND_VF610_NFC) += vf610_nfc.o obj-$(CONFIG_NAND_MXC) += mxc_nand.o diff --git a/drivers/mtd/nand/lpc32xx_nand_slc.c b/drivers/mtd/nand/lpc32xx_nand_slc.c new file mode 100644 index 0000000..719a74d --- /dev/null +++ b/drivers/mtd/nand/lpc32xx_nand_slc.c @@ -0,0 +1,176 @@ +/* + * LPC32xx SLC NAND flash controller driver + * + * (C) Copyright 2015 Vladimir Zapolskiy <vz@mleia.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <nand.h> +#include <asm/errno.h> +#include <asm/io.h> +#include <asm/arch/clk.h> +#include <asm/arch/sys_proto.h> + +struct lpc32xx_nand_slc_regs { + u32 data; + u32 addr; + u32 cmd; + u32 stop; + u32 ctrl; + u32 cfg; + u32 stat; + u32 int_stat; + u32 ien; + u32 isr; + u32 icr; + u32 tac; + u32 tc; + u32 ecc; + u32 dma_data; +}; + +/* CFG register */ +#define CFG_CE_LOW (1 << 5) + +/* CTRL register */ +#define CTRL_SW_RESET (1 << 2) + +/* STAT register */ +#define STAT_NAND_READY (1 << 0) + +/* INT_STAT register */ +#define INT_STAT_TC (1 << 1) +#define INT_STAT_RDY (1 << 0) + +/* TAC register bits, be aware of overflows */ +#define TAC_W_RDY(n) (max_t(uint32_t, (n), 0xF) << 28) +#define TAC_W_WIDTH(n) (max_t(uint32_t, (n), 0xF) << 24) +#define TAC_W_HOLD(n) (max_t(uint32_t, (n), 0xF) << 20) +#define TAC_W_SETUP(n) (max_t(uint32_t, (n), 0xF) << 16) +#define TAC_R_RDY(n) (max_t(uint32_t, (n), 0xF) << 12) +#define TAC_R_WIDTH(n) (max_t(uint32_t, (n), 0xF) << 8) +#define TAC_R_HOLD(n) (max_t(uint32_t, (n), 0xF) << 4) +#define TAC_R_SETUP(n) (max_t(uint32_t, (n), 0xF) << 0) + +static struct lpc32xx_nand_slc_regs __iomem *lpc32xx_nand_slc_regs + = (struct lpc32xx_nand_slc_regs __iomem *)SLC_NAND_BASE; + +static void lpc32xx_nand_init(void) +{ + uint32_t hclk = get_hclk_clk_rate(); + + /* Reset SLC NAND controller */ + writel(CTRL_SW_RESET, &lpc32xx_nand_slc_regs->ctrl); + + /* 8-bit bus, no DMA, no ECC, ordinary CE signal */ + writel(0, &lpc32xx_nand_slc_regs->cfg); + + /* Interrupts disabled and cleared */ + writel(0, &lpc32xx_nand_slc_regs->ien); + writel(INT_STAT_TC | INT_STAT_RDY, + &lpc32xx_nand_slc_regs->icr); + + /* Configure NAND flash timings */ + writel(TAC_W_RDY(CONFIG_LPC32XX_NAND_SLC_WDR_CLKS) | + TAC_W_WIDTH(hclk / CONFIG_LPC32XX_NAND_SLC_WWIDTH) | + TAC_W_HOLD(hclk / CONFIG_LPC32XX_NAND_SLC_WHOLD) | + TAC_W_SETUP(hclk / CONFIG_LPC32XX_NAND_SLC_WSETUP) | + TAC_R_RDY(CONFIG_LPC32XX_NAND_SLC_RDR_CLKS) | + TAC_R_WIDTH(hclk / CONFIG_LPC32XX_NAND_SLC_RWIDTH) | + TAC_R_HOLD(hclk / CONFIG_LPC32XX_NAND_SLC_RHOLD) | + TAC_R_SETUP(hclk / CONFIG_LPC32XX_NAND_SLC_RSETUP), + &lpc32xx_nand_slc_regs->tac); +} + +static void lpc32xx_nand_cmd_ctrl(struct mtd_info *mtd, + int cmd, unsigned int ctrl) +{ + debug("ctrl: 0x%08x, cmd: 0x%08x\n", ctrl, cmd); + + if (ctrl & NAND_NCE) + setbits_le32(&lpc32xx_nand_slc_regs->cfg, CFG_CE_LOW); + else + clrbits_le32(&lpc32xx_nand_slc_regs->cfg, CFG_CE_LOW); + + if (cmd == NAND_CMD_NONE) + return; + + if (ctrl & NAND_CLE) + writel(cmd & 0xFF, &lpc32xx_nand_slc_regs->cmd); + else if (ctrl & NAND_ALE) + writel(cmd & 0xFF, &lpc32xx_nand_slc_regs->addr); +} + +static int lpc32xx_nand_dev_ready(struct mtd_info *mtd) +{ + return readl(&lpc32xx_nand_slc_regs->stat) & STAT_NAND_READY; +} + +static void lpc32xx_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) +{ + while (len-- > 0) + *buf++ = readl(&lpc32xx_nand_slc_regs->data); +} + +static uint8_t lpc32xx_read_byte(struct mtd_info *mtd) +{ + return readl(&lpc32xx_nand_slc_regs->data); +} + +static void lpc32xx_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len) +{ + while (len-- > 0) + writel(*buf++, &lpc32xx_nand_slc_regs->data); +} + +static void lpc32xx_write_byte(struct mtd_info *mtd, uint8_t byte) +{ + writel(byte, &lpc32xx_nand_slc_regs->data); +} + +/* + * LPC32xx has only one SLC NAND controller, don't utilize + * CONFIG_SYS_NAND_SELF_INIT to be able to reuse this function + * both in SPL NAND and U-boot images. + */ +int board_nand_init(struct nand_chip *lpc32xx_chip) +{ + lpc32xx_chip->cmd_ctrl = lpc32xx_nand_cmd_ctrl; + lpc32xx_chip->dev_ready = lpc32xx_nand_dev_ready; + + /* + * Hardware ECC calculation is not supported by the driver, + * because it requires DMA support, see LPC32x0 User Manual, + * note after SLC_ECC register description (UM10326, p.198) + */ + lpc32xx_chip->ecc.mode = NAND_ECC_SOFT; + + /* + * The implementation of these functions is quite common, but + * they MUST be defined, because access to data register + * is strictly 32-bit aligned. + */ + lpc32xx_chip->read_buf = lpc32xx_read_buf; + lpc32xx_chip->read_byte = lpc32xx_read_byte; + lpc32xx_chip->write_buf = lpc32xx_write_buf; + lpc32xx_chip->write_byte = lpc32xx_write_byte; + + /* + * Use default ECC layout, but these values are predefined + * for both small and large page NAND flash devices. + */ + lpc32xx_chip->ecc.size = 256; + lpc32xx_chip->ecc.bytes = 3; + lpc32xx_chip->ecc.strength = 1; + +#if defined(CONFIG_SYS_NAND_USE_FLASH_BBT) + lpc32xx_chip->bbt_options |= NAND_BBT_USE_FLASH; +#endif + + /* Initialize NAND interface */ + lpc32xx_nand_init(); + + return 0; +} |