summaryrefslogtreecommitdiff
path: root/README
diff options
context:
space:
mode:
Diffstat (limited to 'README')
-rw-r--r--README63
1 files changed, 51 insertions, 12 deletions
diff --git a/README b/README
index 668c4e0..4a767e3 100644
--- a/README
+++ b/README
@@ -653,6 +653,9 @@ The following options need to be configured:
CONFIG_RTC_DS1338 - use Maxim, Inc. DS1338 RTC
CONFIG_RTC_DS164x - use Dallas DS164x RTC
+ Note that if the RTC uses I2C, then the I2C interface
+ must also be configured. See I2C Support, below.
+
- Timestamp Support:
When CONFIG_TIMESTAMP is selected, the timestamp
@@ -904,29 +907,48 @@ The following options need to be configured:
- I2C Support: CONFIG_HARD_I2C | CONFIG_SOFT_I2C
- Enables I2C serial bus commands. If this is selected,
- either CONFIG_HARD_I2C or CONFIG_SOFT_I2C must be defined
- to include the appropriate I2C driver.
+ These enable I2C serial bus commands. Defining either of
+ (but not both of) CONFIG_HARD_I2C or CONFIG_SOFT_I2C will
+ include the appropriate I2C driver for the selected cpu.
- See also: common/cmd_i2c.c for a description of the
+ This will allow you to use i2c commands at the u-boot
+ command line (as long as you set CFG_CMD_I2C in
+ CONFIG_COMMANDS) and communicate with i2c based realtime
+ clock chips. See common/cmd_i2c.c for a description of the
command line interface.
+ CONFIG_HARD_I2C selects the CPM hardware driver for I2C.
+
+ CONFIG_SOFT_I2C configures u-boot to use a software (aka
+ bit-banging) driver instead of CPM or similar hardware
+ support for I2C.
- CONFIG_HARD_I2C
+ There are several other quantities that must also be
+ defined when you define CONFIG_HARD_I2C or CONFIG_SOFT_I2C.
- Selects the CPM hardware driver for I2C.
+ In both cases you will need to define CFG_I2C_SPEED
+ to be the frequency (in Hz) at which you wish your i2c bus
+ to run and CFG_I2C_SLAVE to be the address of this node (ie
+ the cpu's i2c node address).
+
+ Now, the u-boot i2c code for the mpc8xx (cpu/mpc8xx/i2c.c)
+ sets the cpu up as a master node and so its address should
+ therefore be cleared to 0 (See, eg, MPC823e User's Manual
+ p.16-473). So, set CFG_I2C_SLAVE to 0.
- CONFIG_SOFT_I2C
+ That's all that's required for CONFIG_HARD_I2C.
- Use software (aka bit-banging) driver instead of CPM
- or similar hardware support for I2C. This is configured
- via the following defines.
+ If you use the software i2c interface (CONFIG_SOFT_I2C)
+ then the following macros need to be defined (examples are
+ from include/configs/lwmon.h):
I2C_INIT
- (Optional). Any commands necessary to enable I2C
+ (Optional). Any commands necessary to enable the I2C
controller or configure ports.
+ eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
+
I2C_PORT
(Only for MPC8260 CPU). The I/O port to use (the code
@@ -939,32 +961,49 @@ The following options need to be configured:
(driven). If the data line is open collector, this
define can be null.
+ eg: #define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
+
I2C_TRISTATE
The code necessary to make the I2C data line tri-stated
(inactive). If the data line is open collector, this
define can be null.
+ eg: #define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
+
I2C_READ
Code that returns TRUE if the I2C data line is high,
FALSE if it is low.
+ eg: #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
+
I2C_SDA(bit)
If <bit> is TRUE, sets the I2C data line high. If it
is FALSE, it clears it (low).
+ eg: #define I2C_SDA(bit) \
+ if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
+ else immr->im_cpm.cp_pbdat &= ~PB_SDA
+
I2C_SCL(bit)
If <bit> is TRUE, sets the I2C clock line high. If it
is FALSE, it clears it (low).
+ eg: #define I2C_SCL(bit) \
+ if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
+ else immr->im_cpm.cp_pbdat &= ~PB_SCL
+
I2C_DELAY
This delay is invoked four times per clock cycle so this
controls the rate of data transfer. The data rate thus
- is 1 / (I2C_DELAY * 4).
+ is 1 / (I2C_DELAY * 4). Often defined to be something
+ like:
+
+ #define I2C_DELAY udelay(2)
CFG_I2C_INIT_BOARD