diff options
Diffstat (limited to 'board/sunxi/Kconfig')
| -rw-r--r-- | board/sunxi/Kconfig | 43 |
1 files changed, 27 insertions, 16 deletions
diff --git a/board/sunxi/Kconfig b/board/sunxi/Kconfig index a6bbf6e..8e27396 100644 --- a/board/sunxi/Kconfig +++ b/board/sunxi/Kconfig @@ -35,8 +35,11 @@ config MACH_SUN5I config MACH_SUN6I bool "sun6i (Allwinner A31)" select CPU_V7 + select CPU_V7_HAS_NONSEC + select CPU_V7_HAS_VIRT select SUNXI_GEN_SUN6I select SUPPORT_SPL + select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT config MACH_SUN7I bool "sun7i (Allwinner A20)" @@ -50,14 +53,25 @@ config MACH_SUN7I config MACH_SUN8I_A23 bool "sun8i (Allwinner A23)" select CPU_V7 + select CPU_V7_HAS_NONSEC + select CPU_V7_HAS_VIRT select SUNXI_GEN_SUN6I select SUPPORT_SPL + select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT config MACH_SUN8I_A33 bool "sun8i (Allwinner A33)" select CPU_V7 + select CPU_V7_HAS_NONSEC + select CPU_V7_HAS_VIRT select SUNXI_GEN_SUN6I select SUPPORT_SPL + select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT + +config MACH_SUN9I + bool "sun9i (Allwinner A80)" + select CPU_V7 + select SUNXI_GEN_SUN6I endchoice @@ -187,6 +201,7 @@ config SYS_CONFIG_NAME default "sun6i" if MACH_SUN6I default "sun7i" if MACH_SUN7I default "sun8i" if MACH_SUN8I + default "sun9i" if MACH_SUN9I config SYS_BOARD default "sunxi" @@ -194,24 +209,8 @@ config SYS_BOARD config SYS_SOC default "sunxi" -config SPL_FEL - bool "SPL/FEL mode support" - depends on SPL - default n - help - This enables support for Fast Early Loader (FEL) mode. This - allows U-Boot to be loaded to the board over USB by the on-chip - boot rom. U-Boot should be sent in two parts: SPL first, with - 'fel write 0x2000 u-boot-spl.bin; fel exe 0x2000' then U-Boot with - 'fel write 0x4a000000 u-boot.bin; fel exe 0x4a000000'. This option - shrinks the amount of SRAM available to SPL, so only enable it if - you need FEL. Note that enabling this option only allows FEL to be - used; it is still possible to boot U-Boot from boot media. U-Boot - SPL detects when it is being loaded using FEL. - config UART0_PORT_F bool "UART0 on MicroSD breakout board" - depends on SPL_FEL default n ---help--- Repurpose the SD card slot for getting access to the UART0 serial @@ -281,6 +280,18 @@ config MMC_SUNXI_SLOT_EXTRA slot or emmc on mmc1 - mmc3. Setting this to 1, 2 or 3 will enable support for this. +config SPL_NAND_SUPPORT + bool "SPL/NAND mode support" + depends on SPL + default n + ---help--- + This enables support for booting from NAND internal + memory. U-Boot SPL doesn't detect where is it load from, + therefore this option is needed to properly load image from + flash. Option also disables MMC functionality on U-Boot due to + initialization errors encountered, when both controllers are + enabled. + config USB0_VBUS_PIN string "Vbus enable pin for usb0 (otg)" default "" |