summaryrefslogtreecommitdiff
path: root/board
diff options
context:
space:
mode:
Diffstat (limited to 'board')
-rw-r--r--board/gen860t/Kconfig11
-rw-r--r--board/gen860t/MAINTAINERS7
-rw-r--r--board/gen860t/Makefile8
-rw-r--r--board/gen860t/README131
-rw-r--r--board/gen860t/beeper.c183
-rw-r--r--board/gen860t/beeper.h13
-rw-r--r--board/gen860t/flash.c628
-rw-r--r--board/gen860t/fpga.c362
-rw-r--r--board/gen860t/fpga.h26
-rw-r--r--board/gen860t/gen860t.c278
-rw-r--r--board/gen860t/ioport.c331
-rw-r--r--board/gen860t/ioport.h26
-rw-r--r--board/gen860t/u-boot-flashenv.lds92
-rw-r--r--board/gen860t/u-boot.lds87
14 files changed, 0 insertions, 2183 deletions
diff --git a/board/gen860t/Kconfig b/board/gen860t/Kconfig
deleted file mode 100644
index 438f7cc..0000000
--- a/board/gen860t/Kconfig
+++ /dev/null
@@ -1,11 +0,0 @@
-if TARGET_GEN860T
-
-config SYS_BOARD
- string
- default "gen860t"
-
-config SYS_CONFIG_NAME
- string
- default "GEN860T"
-
-endif
diff --git a/board/gen860t/MAINTAINERS b/board/gen860t/MAINTAINERS
deleted file mode 100644
index c5d3da3..0000000
--- a/board/gen860t/MAINTAINERS
+++ /dev/null
@@ -1,7 +0,0 @@
-GEN860T BOARD
-M: Keith Outwater <Keith_Outwater@mvis.com>
-S: Orphan (since 2014-06)
-F: board/gen860t/
-F: include/configs/GEN860T.h
-F: configs/GEN860T_defconfig
-F: configs/GEN860T_SC_defconfig
diff --git a/board/gen860t/Makefile b/board/gen860t/Makefile
deleted file mode 100644
index 86ae5e8..0000000
--- a/board/gen860t/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = gen860t.o flash.o beeper.o fpga.o ioport.o
diff --git a/board/gen860t/README b/board/gen860t/README
deleted file mode 100644
index 3ef8ae1..0000000
--- a/board/gen860t/README
+++ /dev/null
@@ -1,131 +0,0 @@
-This directory contains board specific code for a generic MPC860T based
-embedded computer, called 'GEN860T'. The design is generic in the sense that
-common, readily available components are used and that the architecture of the
-system is relatively straightforward:
-
- One eight bit wide boot (FLASH) memory
- 32 bit main memory using SDRAM
- DOC 2000+
- Ethernet PHY
- Some I2C peripheral devices: Atmel AT24C256 EEPROM, Maxim DS1337 RTC.
- Some other miscellaneous peripherals
-
-NOTE: There are references to a XIlinx FPGA and Mil-Std 1553 databus in this
-port. I guess the computer is not as generic as I first said 8) However,
-these extras can be safely ignored.
-
-Given the GEN860T files, it should be pretty easy to reverse engineer the
-hardware configuration, if that's useful to you. Hopefully, this code will
-be useful to someone as a basis for a port to a new system or as a head start
-on a custom design. If you end up using any of this, I would appreciate
-hearing from you, especially if you discover bugs or find ways to improve the
-quality of this U-Boot port.
-
-Here are the salient features of the system:
-Clock : 33.3 Mhz oscillator
-Processor core frequency : 66.6 Mhz if in 1:2:1 mode; can also run 1:1
-Bus frequency : 33.3 Mhz
-
-Main memory:
- Type : SDRAM
- Width : 32 bits
- Size : 64 mibibytes
- Chip : Two Micron MT48LC16M16A2TG-7E
- CS : MPC860T CS1*/UPMA
- UPMA CONNECTIONS:
- SDRAM A10 : GPLA0*
- SDRAM CAS* : GPLA2*
- SDRAM WE* : GPLA3*
- SDRAM RAS* : GPLA4*
-
-Boot memory:
- Type : FLASH
- Width : 8 bits
- Size : 16 mibibytes
- Chip : One Intel 28F128J3A (StrataFlash)
- CS : MPC860T CS0*/GPCM (this is the "boot" chip select)
-
-EEPROM memory:
- Type : Serial I2C EEPROM
- Width : 8 bits
- Size : 32 kibibytes
- Chip : One Atmel AT25C256
- CS : 0x50 (external I2C address pins on device are tied to GND)
-
-Filesystem memory:
- Type : NAND FLASH (Toshiba)
- Width : 8 bits (i.e. interface to DOC is 8 bits)
- Size : 32 mibibytes
- Chip : One DiskOnCHip Millenium Plus (DOC 2000+)
- CS : MPC860T CS2*/GPCM
-
-Network support:
- MAC : MPC86OT FEC (Fast Ethernet Controller)
- PHY : Intel LXT971A
- MII Addr: 0x0 (hardwired on the board)
- MII IRQ :
-
-Console:
- RS-232 on SMC1 (Maxim MAX3232 LVCMOS-RS232 level shifter)
-
-Real Time Clock:
- Type : Low power, I2C interface
- Chip : Maxim DS1337
- CS : Address 0x68 on I2C bus
-
- The MPC860T's internal RTC has a defect in Mask rev D that increases
- the current drain on the KAPWR line to 10 mA. Since this is an
- unreasonable amount of current draw for a RTC, and Motorola does not
- plan to fix this in future mask revisions, a serial (I2C) RTC that
- works has been included instead. NOTE that the DS1337 can be
- configured to output a 32768 Hz clock while the main power is on.
- This clock output has been routed to the MPC860T's EXTAL pin to allow
- the internal RTC to be used. NOTE also that due to yet another
- defect in the rev D mask, the RTC does not operate reliably when the
- internal RTC divisor is set to use a 32768 Hz reference. So just use
- the I2C RTC.
-
-Miscellaneous:
- Xilinx Virtex FPGA on CS3*/GPCM.
- Virtex FPGA slave SelectMap interface on cs4*/UPMB.
- Mil-Std 1553 databus interface on CS5*/GPCM.
- Audio sounder (beeper) with digital volume control connected to SPKROUT.
-
-SC variant:
- A reduced-feature version of the GEN860T port is also supported: GEN860T_SC.
- The 'SC' variant only provides support for the Virtex FPGA, SDRAM main
- memory, EEPROM and flash memory. The system clock frequency is reduced
- to 24 MHz.
-
-Issues:
- The DOC 2000+ returns 0x40 as its device ID when probed using the method
- desxribed in the DOC datasheet. Unfortunately, the U-Boot DOC driver
- does not recognize this device. As of this writing, it seems that MTD
- does not support the DOC 2000+ either.
-
-Status:
- Everything appears to work except DOC support. As of this writing,
- David Woodhouse has stated on the MTD mailing list that he has no
- knowledge of the DOC Millineum Plus and therfore there is no support
- in MTD for this device. I wish I had known this sooner :(
-
-The GEN860T board specific files and configuration is based on the work
-of others who have contributed to U-Boot. The copyright and license notices
-of these authors have been retained wherever their code has been reused.
-All new code to support the GEN860T board is:
-
- (C) Copyright 2001-2003
- Keith Outwater (keith_outwater@mvis.com)
-
-and the following license applies:
-
-SPDX-License-Identifier: GPL-2.0+
-
-Thanks to Wolfgang Denk for a great software package and to everyone
-who contributed to its development.
-
-Keith Outwater
-Sr. Staff Engineer
-Microvision, Inc.
-<keith_outwater@mvis.com>
-<outwater@eskimo.com>
diff --git a/board/gen860t/beeper.c b/board/gen860t/beeper.c
deleted file mode 100644
index 0bebca9..0000000
--- a/board/gen860t/beeper.c
+++ /dev/null
@@ -1,183 +0,0 @@
-/*
- * (C) Copyright 2002
- * Keith Outwater, keith_outwater@mvis.com
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc8xx.h>
-#include <asm/8xx_immap.h>
-#include <linux/ctype.h>
-
-/*
- * Basic beeper support for the GEN860T board. The GEN860T includes
- * an audio sounder driven by a Phillips TDA8551 amplifier. The
- * TDA8551 features a digital volume control which uses a "trinary"
- * input (high/high-Z/low) to set volume. The 860's SPKROUT pin
- * drives the amplifier input.
- */
-
-/*
- * Initialize beeper-related hardware. Initialize timer 1 for use with
- * the beeper. Use 66 MHz internal clock with prescale of 33 to get
- * 1 uS period per count.
- * FIXME: we should really compute the prescale based on the reported
- * core clock frequency.
- */
-void init_beeper (void)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
-
- immap->im_cpmtimer.cpmt_tgcr &= ~TGCR_RST1 | TGCR_STP1;
- immap->im_cpmtimer.cpmt_tmr1 = ((33 << TMR_PS_SHIFT) & TMR_PS_MSK)
- | TMR_OM | TMR_FRR | TMR_ICLK_IN_GEN;
- immap->im_cpmtimer.cpmt_tcn1 = 0;
- immap->im_cpmtimer.cpmt_ter1 = 0xffff;
- immap->im_cpmtimer.cpmt_tgcr |= TGCR_RST1;
-}
-
-/*
- * Set beeper frequency. Max allowed frequency is 2.5 KHz. This limit
- * is mostly arbitrary, but the beeper isn't really much good beyond this
- * frequency.
- */
-void set_beeper_frequency (uint frequency)
-{
-#define FREQ_LIMIT 2500
-
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
-
- /*
- * Compute timer ticks given desired frequency. The timer is set up
- * to count 0.5 uS per tick and it takes two ticks per cycle (Hz).
- */
- if (frequency > FREQ_LIMIT)
- frequency = FREQ_LIMIT;
- frequency = 1000000 / frequency;
- immap->im_cpmtimer.cpmt_trr1 = (ushort) frequency;
-}
-
-/*
- * Turn the beeper on
- */
-void beeper_on (void)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
-
- immap->im_cpmtimer.cpmt_tgcr &= ~TGCR_STP1;
-}
-
-/*
- * Turn the beeper off
- */
-void beeper_off (void)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
-
- immap->im_cpmtimer.cpmt_tgcr |= TGCR_STP1;
-}
-
-/*
- * Increase or decrease the beeper volume. Volume can be set
- * from off to full in 64 steps. To increase volume, the output
- * pin is actively driven high, then returned to tristate.
- * To decrease volume, output a low on the port pin (no need to
- * change pin mode to tristate) then output a high to go back to
- * tristate.
- */
-void set_beeper_volume (int steps)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- int i;
-
- if (steps >= 0) {
- for (i = 0; i < (steps >= 64 ? 64 : steps); i++) {
- immap->im_cpm.cp_pbodr &= ~(0x80000000 >> 19);
- udelay (1);
- immap->im_cpm.cp_pbodr |= (0x80000000 >> 19);
- udelay (1);
- }
- } else {
- for (i = 0; i > (steps <= -64 ? -64 : steps); i--) {
- immap->im_cpm.cp_pbdat &= ~(0x80000000 >> 19);
- udelay (1);
- immap->im_cpm.cp_pbdat |= (0x80000000 >> 19);
- udelay (1);
- }
- }
-}
-
-/*
- * Check the environment to see if the beeper needs beeping.
- * Controlled by a sequence of the form:
- * freq/delta volume/on time/off time;... where:
- * freq = frequency in Hz (0 - 2500)
- * delta volume = volume steps up or down (-64 <= vol <= 64)
- * on time = time in mS
- * off time = time in mS
- *
- * Return 1 on success, 0 on failure
- */
-int do_beeper (char *sequence)
-{
-#define DELIMITER ';'
-
- int args[4];
- int i;
- int val;
- char *p = sequence;
- char *tp;
-
- /*
- * Parse the control sequence. This is a really simple parser
- * without any real error checking. You can probably blow it
- * up really easily.
- */
- if (*p == '\0' || !isdigit (*p)) {
- printf ("%s:%d: null or invalid string (%s)\n",
- __FILE__, __LINE__, p);
- return 0;
- }
-
- i = 0;
- while (*p != '\0') {
- while (*p != DELIMITER) {
- if (i > 3)
- i = 0;
- val = (int) simple_strtol (p, &tp, 0);
- if (tp == p) {
- printf ("%s:%d: no digits or bad format\n",
- __FILE__, __LINE__);
- return 0;
- } else {
- args[i] = val;
- }
-
- i++;
- if (*tp == DELIMITER)
- p = tp;
- else
- p = ++tp;
- }
- p++;
-
- /*
- * Well, we got something that has a chance of being correct
- */
-#if 0
- for (i = 0; i < 4; i++) {
- printf ("%s:%d:arg %d = %d\n", __FILE__, __LINE__, i,
- args[i]);
- }
- printf ("\n");
-#endif
- set_beeper_frequency (args[0]);
- set_beeper_volume (args[1]);
- beeper_on ();
- udelay (1000 * args[2]);
- beeper_off ();
- udelay (1000 * args[3]);
- }
- return 1;
-}
diff --git a/board/gen860t/beeper.h b/board/gen860t/beeper.h
deleted file mode 100644
index 0734fca..0000000
--- a/board/gen860t/beeper.h
+++ /dev/null
@@ -1,13 +0,0 @@
-/*
- * (C) Copyright 2002
- * Keith Outwater, keith_outwater@mvis.com
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-void init_beeper(void);
-void set_beeper_frequency(uint frequency);
-void beeper_on(void);
-void beeper_off(void);
-void set_beeper_volume(int steps);
-int do_beeper(char *sequence);
diff --git a/board/gen860t/flash.c b/board/gen860t/flash.c
deleted file mode 100644
index ca1ed3d..0000000
--- a/board/gen860t/flash.c
+++ /dev/null
@@ -1,628 +0,0 @@
-/*
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- * Keith Outwater, keith_outwater@mvsi.com
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc8xx.h>
-
-#if defined(CONFIG_ENV_IS_IN_FLASH)
-# ifndef CONFIG_ENV_ADDR
-# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
-# endif
-# ifndef CONFIG_ENV_SIZE
-# define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-# endif
-# ifndef CONFIG_ENV_SECT_SIZE
-# define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
-# endif
-#endif
-
-/*
- * Use buffered writes to flash by default - they are about 32x faster than
- * single byte writes.
- */
-#ifndef CONFIG_SYS_GEN860T_FLASH_USE_WRITE_BUFFER
-#define CONFIG_SYS_GEN860T_FLASH_USE_WRITE_BUFFER
-#endif
-
-/*
- * Max time to wait (in mS) for flash device to allocate a write buffer.
- */
-#ifndef CONFIG_SYS_FLASH_ALLOC_BUFFER_TOUT
-#define CONFIG_SYS_FLASH_ALLOC_BUFFER_TOUT 100
-#endif
-
-/*
- * These functions support a single Intel StrataFlash device (28F128J3A)
- * in byte mode only!. The flash routines are very basic and simple
- * since there isn't really any remapping necessary.
- */
-
-/*
- * Intel SCS (Scalable Command Set) command definitions
- * (taken from 28F128J3A datasheet)
- */
-#define SCS_READ_CMD 0xff
-#define SCS_READ_ID_CMD 0x90
-#define SCS_QUERY_CMD 0x98
-#define SCS_READ_STATUS_CMD 0x70
-#define SCS_CLEAR_STATUS_CMD 0x50
-#define SCS_WRITE_BUF_CMD 0xe8
-#define SCS_PROGRAM_CMD 0x40
-#define SCS_BLOCK_ERASE_CMD 0x20
-#define SCS_BLOCK_ERASE_RESUME_CMD 0xd0
-#define SCS_PROGRAM_RESUME_CMD 0xd0
-#define SCS_BLOCK_ERASE_SUSPEND_CMD 0xb0
-#define SCS_SET_BLOCK_LOCK_CMD 0x60
-#define SCS_CLR_BLOCK_LOCK_CMD 0x60
-
-/*
- * SCS status/extended status register bit definitions
- */
-#define SCS_SR7 0x80
-#define SCS_XSR7 0x80
-
-/*---------------------------------------------------------------------*/
-#if 0
-#define DEBUG_FLASH
-#endif
-
-#ifdef DEBUG_FLASH
-#define PRINTF(fmt,args...) printf(fmt ,##args)
-#else
-#define PRINTF(fmt,args...)
-#endif
-/*---------------------------------------------------------------------*/
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size (vu_char *addr, flash_info_t *info);
-static int write_data8 (flash_info_t *info, ulong dest, uchar data);
-static void flash_get_offsets (ulong base, flash_info_t *info);
-
-/*-----------------------------------------------------------------------
- * Initialize the flash memory.
- */
-unsigned long
-flash_init (void)
-{
- volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
- unsigned long size_b0;
- int i;
-
- for (i= 0; i < CONFIG_SYS_MAX_FLASH_BANKS; ++i) {
- flash_info[i].flash_id = FLASH_UNKNOWN;
- }
-
- /*
- * The gen860t board only has one FLASH memory device, so the
- * FLASH Bank configuration is done statically.
- */
- PRINTF("\n## Get flash bank 1 size @ 0x%08x\n", FLASH_BASE0_PRELIM);
- size_b0 = flash_get_size((vu_char *)FLASH_BASE0_PRELIM, &flash_info[0]);
- if (flash_info[0].flash_id == FLASH_UNKNOWN) {
- printf ("## Unknown FLASH on Bank 0: "
- "ID 0x%lx, Size = 0x%08lx = %ld MB\n",
- flash_info[0].flash_id,size_b0, size_b0 << 20);
- }
-
- PRINTF("## Before remap:\n"
- " BR0: 0x%08x OR0: 0x%08x\n BR1: 0x%08x OR1: 0x%08x\n",
- memctl->memc_br0, memctl->memc_or0,
- memctl->memc_br1, memctl->memc_or1);
-
- /*
- * Remap FLASH according to real size
- */
- memctl->memc_or0 |= (-size_b0 & 0xFFFF8000);
- memctl->memc_br0 |= (CONFIG_SYS_FLASH_BASE & BR_BA_MSK);
-
- PRINTF("## After remap:\n"
- " BR0: 0x%08x OR0: 0x%08x\n", memctl->memc_br0, memctl->memc_or0);
-
- /*
- * Re-do sizing to get full correct info
- */
- size_b0 = flash_get_size ((vu_char *)CONFIG_SYS_FLASH_BASE, &flash_info[0]);
- flash_get_offsets (CONFIG_SYS_FLASH_BASE, &flash_info[0]);
- flash_info[0].size = size_b0;
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
- /*
- * Monitor protection is ON by default
- */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1,
- &flash_info[0]);
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
- /*
- * Environment protection ON by default
- */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE - 1,
- &flash_info[0]);
-#endif
-
- PRINTF("## Final Flash bank size: 0x%08lx\n",size_b0);
- return (size_b0);
-}
-
-
-/*-----------------------------------------------------------------------
- * Fill in the FLASH offset table
- */
-static void
-flash_get_offsets (ulong base, flash_info_t *info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- return;
- }
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_INTEL:
- for (i = 0; i < info->sector_count; i++) {
- info->start[i] = base;
- base += 1024 * 128;
- }
- return;
-
- default:
- printf ("Don't know sector offsets for FLASH"
- " type 0x%lx\n", info->flash_id);
- return;
- }
-}
-
-
-/*-----------------------------------------------------------------------
- * Display FLASH device info
- */
-void
-flash_print_info (flash_info_t *info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("Missing or unknown FLASH type\n");
- return;
- }
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_INTEL:
- printf ("Intel ");
- break;
- default:
- printf ("Unknown Vendor ");
- break;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_28F128J3A:
- printf ("28F128J3A (128Mbit = 128K x 128)\n");
- break;
- default:
- printf ("Unknown Chip Type\n");
- break;
- }
-
- if (info->size >= (1024 * 1024)) {
- i = 20;
- } else {
- i = 10;
- }
- printf (" Size: %ld %cB in %d Sectors\n",
- info->size >> i,
- (i == 20) ? 'M' : 'k',
- info->sector_count);
-
- printf (" Sector Start Addresses:");
- for (i=0; i<info->sector_count; ++i) {
- if ((i % 5) == 0)
- printf ("\n ");
- printf (" %08lX%s",
- info->start[i],
- info->protect[i] ? " (RO)" : " "
- );
- }
- printf ("\n");
- return;
-}
-
-
-/*-----------------------------------------------------------------------
- * Get size and other information for a FLASH device.
- * NOTE: The following code cannot be run from FLASH!
- */
-static
-ulong flash_get_size (vu_char *addr, flash_info_t *info)
-{
-#define NO_FLASH 0
-
- vu_char value[2];
-
- /*
- * Try to read the manufacturer ID
- */
- addr[0] = SCS_READ_CMD;
- addr[0] = SCS_READ_ID_CMD;
- value[0] = addr[0];
- value[1] = addr[2];
- addr[0] = SCS_READ_CMD;
-
- PRINTF("Manuf. ID @ 0x%08lx: 0x%02x\n", (ulong)addr, value[0]);
- switch (value[0]) {
- case (INTEL_MANUFACT & 0xff):
- info->flash_id = FLASH_MAN_INTEL;
- break;
- default:
- info->flash_id = FLASH_UNKNOWN;
- info->sector_count = 0;
- info->size = 0;
- return (NO_FLASH);
- }
-
- /*
- * Read the device ID
- */
- PRINTF("Device ID @ 0x%08lx: 0x%02x\n", (ulong)(&addr[2]), value[1]);
- switch (value[1]) {
- case (INTEL_ID_28F128J3A & 0xff):
- info->flash_id += FLASH_28F128J3A;
- info->sector_count = 128;
- info->size = 16 * 1024 * 1024;
- break;
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- return (NO_FLASH);
- }
-
- if (info->sector_count > CONFIG_SYS_MAX_FLASH_SECT) {
- printf ("** ERROR: sector count %d > max (%d) **\n",
- info->sector_count, CONFIG_SYS_MAX_FLASH_SECT);
- info->sector_count = CONFIG_SYS_MAX_FLASH_SECT;
- }
- return (info->size);
-}
-
-
-/*-----------------------------------------------------------------------
- * Erase the specified sectors in the specified FLASH device
- */
-int
-flash_erase(flash_info_t *info, int s_first, int s_last)
-{
- int flag, prot, sect;
- ulong start, now, last;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("- missing\n");
- } else {
- printf ("- no sectors to erase\n");
- }
- return 1;
- }
-
- if ((info->flash_id & FLASH_VENDMASK) != FLASH_MAN_INTEL) {
- printf ("Can erase only Intel flash types - aborted\n");
- return 1;
- }
-
- prot = 0;
- for (sect=s_first; sect<=s_last; ++sect) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot) {
- printf ("- Warning: %d protected sectors will not be erased!\n",
- prot);
- } else {
- printf ("\n");
- }
-
- start = get_timer (0);
- last = start;
-
- /*
- * Start erase on unprotected sectors
- */
- for (sect = s_first; sect<=s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- vu_char *addr = (uchar *)(info->start[sect]);
- vu_char status;
-
- /*
- * Disable interrupts which might cause a timeout
- */
- flag = disable_interrupts();
-
- *addr = SCS_CLEAR_STATUS_CMD;
- *addr = SCS_BLOCK_ERASE_CMD;
- *addr = SCS_BLOCK_ERASE_RESUME_CMD;
-
- /*
- * Re-enable interrupts if necessary
- */
- if (flag)
- enable_interrupts();
-
- /*
- * Wait at least 80us - let's wait 1 ms
- */
- udelay (1000);
-
- while (((status = *addr) & SCS_SR7) != SCS_SR7) {
- if ((now=get_timer(start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout\n");
- *addr = SCS_BLOCK_ERASE_SUSPEND_CMD;
- *addr = SCS_READ_CMD;
- return 1;
- }
-
- /*
- * Show that we're waiting
- */
- if ((now - last) > 1000) { /* 1 second */
- putc ('.');
- last = now;
- }
- }
- *addr = SCS_READ_CMD;
- }
- }
- printf (" done\n");
- return 0;
-}
-
-
-#ifdef CONFIG_SYS_GEN860T_FLASH_USE_WRITE_BUFFER
-/*
- * Allocate a flash buffer, fill it with data and write it to the flash.
- * 0 - OK
- * 1 - Timeout on buffer request
- *
- * NOTE: After the last call to this function, WSM status needs to be checked!
- */
-static int
-write_flash_buffer8(flash_info_t *info_p, vu_char *src_p, vu_char *dest_p,
- uint count)
-{
- vu_char *block_addr_p = NULL;
- vu_char *start_addr_p = NULL;
- ulong blocksize = info_p->size / (ulong)info_p->sector_count;
-
- int i;
- uint time = get_timer(0);
-
- PRINTF("%s:%d: src: 0x%p dest: 0x%p count: %d\n",
- __FUNCTION__, __LINE__, src_p, dest_p, count);
-
- /*
- * What block are we in? We already know that the source address is
- * in the flash address range, but we also can't cross a block boundary.
- * We assume that the block does not cross a boundary (we'll check before
- * calling this function).
- */
- for (i = 0; i < info_p->sector_count; ++i) {
- if ( ((ulong)dest_p >= info_p->start[i]) &&
- ((ulong)dest_p < (info_p->start[i] + blocksize)) ) {
- PRINTF("%s:%d: Dest addr 0x%p is in block %d @ 0x%.8lx\n",
- __FUNCTION__, __LINE__, dest_p, i, info_p->start[i]);
- block_addr_p = (vu_char *)info_p->start[i];
- break;
- }
- }
-
- /*
- * Request a buffer
- */
- *block_addr_p = SCS_WRITE_BUF_CMD;
- while ((*block_addr_p & SCS_XSR7) != SCS_XSR7) {
- if (get_timer(time) > CONFIG_SYS_FLASH_ALLOC_BUFFER_TOUT) {
- PRINTF("%s:%d: Buffer allocation timeout @ 0x%p (waited %d mS)\n",
- __FUNCTION__, __LINE__, block_addr_p,
- CONFIG_SYS_FLASH_ALLOC_BUFFER_TOUT);
- return 1;
- }
- *block_addr_p = SCS_WRITE_BUF_CMD;
- }
-
- /*
- * Fill the buffer with data
- */
- start_addr_p = dest_p;
- *block_addr_p = count - 1; /* flash device wants count - 1 */
- PRINTF("%s:%d: Fill buffer at block addr 0x%p\n",
- __FUNCTION__, __LINE__, block_addr_p);
- for (i = 0; i < count; i++) {
- *start_addr_p++ = *src_p++;
- }
-
- /*
- * Flush buffer to flash
- */
- *block_addr_p = SCS_PROGRAM_RESUME_CMD;
-#if 1
- time = get_timer(0);
- while ((*block_addr_p & SCS_SR7) != SCS_SR7) {
- if (get_timer(time) > CONFIG_SYS_FLASH_WRITE_TOUT) {
- PRINTF("%s:%d: Write timeout @ 0x%p (waited %d mS)\n",
- __FUNCTION__, __LINE__, block_addr_p, CONFIG_SYS_FLASH_WRITE_TOUT);
- return 1;
- }
- }
-
-#endif
- return 0;
-}
-#endif
-
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- * 4 - Flash not identified
- */
-int
-write_buff(flash_info_t *info_p, uchar *src_p, ulong addr, ulong count)
-{
- int rc = 0;
-#ifdef CONFIG_SYS_GEN860T_FLASH_USE_WRITE_BUFFER
-#define FLASH_WRITE_BUF_SIZE 0x00000020 /* 32 bytes */
- int i;
- uint bufs;
- ulong buf_count;
- vu_char *sp;
- vu_char *dp;
-#else
- ulong wp;
-#endif
-
- PRINTF("\n%s:%d: src: 0x%.8lx dest: 0x%.8lx size: %d (0x%.8lx)\n",
- __FUNCTION__, __LINE__, (ulong)src_p, addr, (uint)count, count);
-
- if (info_p->flash_id == FLASH_UNKNOWN) {
- return 4;
- }
-
-#ifdef CONFIG_SYS_GEN860T_FLASH_USE_WRITE_BUFFER
- sp = src_p;
- dp = (uchar *)addr;
-
- /*
- * For maximum performance, we want to align the start address to
- * the beginning of a write buffer boundary (i.e. A4-A0 of the
- * start address = 0). See how many bytes are required to get to a
- * write-buffer-aligned address. If that number is non-zero, do
- * non buffered writes of the non-aligned data. By doing non-buffered
- * writes, we avoid the problem of crossing a block (sector) boundary
- * with buffered writes.
- */
- buf_count = FLASH_WRITE_BUF_SIZE - (addr & (FLASH_WRITE_BUF_SIZE - 1));
- if (buf_count == FLASH_WRITE_BUF_SIZE) { /* already on a boundary */
- buf_count = 0;
- }
- if (buf_count > count) { /* not a full buffers worth of data to write */
- buf_count = count;
- }
- count -= buf_count;
-
- PRINTF("%s:%d: Write buffer alignment count = %ld\n",
- __FUNCTION__, __LINE__, buf_count);
- while (buf_count-- >= 1) {
- if ((rc = write_data8(info_p, (ulong)dp++, *sp++)) != 0) {
- return (rc);
- }
- }
-
- PRINTF("%s:%d: count = %ld\n", __FUNCTION__, __LINE__, count);
- if (count == 0) { /* all done */
- PRINTF("%s:%d: Less than 1 buffer (%d) worth of bytes\n",
- __FUNCTION__, __LINE__, FLASH_WRITE_BUF_SIZE);
- return (rc);
- }
-
- /*
- * Now that we are write buffer aligned, write full or partial buffers.
- * The fact that we are write buffer aligned automatically avoids
- * crossing a block address during a write buffer operation.
- */
- bufs = count / FLASH_WRITE_BUF_SIZE;
- PRINTF("%s:%d: %d (0x%x) buffers to write\n", __FUNCTION__, __LINE__,
- bufs, bufs);
- while (bufs >= 1) {
- rc = write_flash_buffer8(info_p, sp, dp, FLASH_WRITE_BUF_SIZE);
- if (rc != 0) {
- PRINTF("%s:%d: ** Error writing buf %d\n",
- __FUNCTION__, __LINE__, bufs);
- return (rc);
- }
- bufs--;
- sp += FLASH_WRITE_BUF_SIZE;
- dp += FLASH_WRITE_BUF_SIZE;
- }
-
- /*
- * Do the leftovers
- */
- i = count % FLASH_WRITE_BUF_SIZE;
- PRINTF("%s:%d: %d (0x%x) leftover bytes\n", __FUNCTION__, __LINE__, i, i);
- if (i > 0) {
- rc = write_flash_buffer8(info_p, sp, dp, i);
- }
-
- sp = (vu_char*)info_p->start[0];
- *sp = SCS_READ_CMD;
- return (rc);
-
-#else
- wp = addr;
- while (count-- >= 1) {
- if((rc = write_data8(info_p, wp++, *src_p++)) != 0)
- return (rc);
- }
- return 0;
-#endif
-}
-
-
-/*-----------------------------------------------------------------------
- * Write a byte to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int
-write_data8 (flash_info_t *info, ulong dest, uchar data)
-{
- vu_char *addr = (vu_char *)dest;
- vu_char status;
- ulong start;
- int flag;
-
- /* Check if Flash is (sufficiently) erased */
- if ((*addr & data) != data) {
- return (2);
- }
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- *addr = SCS_PROGRAM_CMD;
- *addr = data;
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- start = get_timer (0);
-
- while (((status = *addr) & SCS_SR7) != SCS_SR7) {
- if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
- *addr = SCS_READ_CMD;
- return (1);
- }
- }
- *addr = SCS_READ_CMD;
- return (0);
-}
-
-/* vim: set ts=4 sw=4 tw=78: */
diff --git a/board/gen860t/fpga.c b/board/gen860t/fpga.c
deleted file mode 100644
index dd0ef70..0000000
--- a/board/gen860t/fpga.c
+++ /dev/null
@@ -1,362 +0,0 @@
-/*
- * (C) Copyright 2002
- * Rich Ireland, Enterasys Networks, rireland@enterasys.com.
- * Keith Outwater, keith_outwater@mvis.com.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * Virtex2 FPGA configuration support for the GEN860T computer
- */
-
-#include <common.h>
-#include <virtex2.h>
-#include <command.h>
-#include "fpga.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#if defined(CONFIG_FPGA)
-
-#if 0
-#define GEN860T_FPGA_DEBUG
-#endif
-
-#ifdef GEN860T_FPGA_DEBUG
-#define PRINTF(fmt,args...) printf (fmt ,##args)
-#else
-#define PRINTF(fmt,args...)
-#endif
-
-/*
- * Port bit numbers for the Selectmap controls
- */
-#define FPGA_INIT_BIT_NUM 22 /* PB22 */
-#define FPGA_RESET_BIT_NUM 11 /* PC11 */
-#define FPGA_DONE_BIT_NUM 16 /* PB16 */
-#define FPGA_PROGRAM_BIT_NUM 7 /* PA7 */
-
-/* Note that these are pointers to code that is in Flash. They will be
- * relocated at runtime.
- */
-xilinx_virtex2_slave_selectmap_fns fpga_fns = {
- fpga_pre_config_fn,
- fpga_pgm_fn,
- fpga_init_fn,
- fpga_err_fn,
- fpga_done_fn,
- fpga_clk_fn,
- fpga_cs_fn,
- fpga_wr_fn,
- fpga_read_data_fn,
- fpga_write_data_fn,
- fpga_busy_fn,
- fpga_abort_fn,
- fpga_post_config_fn
-};
-
-xilinx_desc fpga[CONFIG_FPGA_COUNT] = {
- {xilinx_virtex2,
- slave_selectmap,
- XILINX_XC2V3000_SIZE,
- (void *) &fpga_fns,
- 0}
-};
-
-/*
- * Display FPGA revision information
- */
-void print_fpga_revision (void)
-{
- vu_long *rev_p = (vu_long *) 0x60000008;
-
- printf ("FPGA Revision 0x%.8lx"
- " (Date %.2lx/%.2lx/%.2lx, Status \"%.1lx\", Version %.3lu)\n",
- *rev_p,
- ((*rev_p >> 28) & 0xf),
- ((*rev_p >> 20) & 0xff),
- ((*rev_p >> 12) & 0xff),
- ((*rev_p >> 8) & 0xf), (*rev_p & 0xff));
-}
-
-
-/*
- * Perform a simple test of the FPGA to processor interface using the FPGA's
- * inverting bus test register. The great thing about doing a read/write
- * test on a register that inverts it's contents is that you avoid any
- * problems with bus charging.
- * Return 0 on failure, 1 on success.
- */
-int test_fpga_ibtr (void)
-{
- vu_long *ibtr_p = (vu_long *) 0x60000010;
- vu_long readback;
- vu_long compare;
- int i;
- int j;
- int k;
- int pass = 1;
-
- static const ulong bitpattern[] = {
- 0xdeadbeef, /* magic ID pattern for debug */
- 0x00000001, /* single bit */
- 0x00000003, /* two adjacent bits */
- 0x00000007, /* three adjacent bits */
- 0x0000000F, /* four adjacent bits */
- 0x00000005, /* two non-adjacent bits */
- 0x00000015, /* three non-adjacent bits */
- 0x00000055, /* four non-adjacent bits */
- 0xaaaaaaaa, /* alternating 1/0 */
- };
-
- for (i = 0; i < 1024; i++) {
- for (j = 0; j < 31; j++) {
- for (k = 0;
- k < sizeof (bitpattern) / sizeof (bitpattern[0]);
- k++) {
- *ibtr_p = compare = (bitpattern[k] << j);
- readback = *ibtr_p;
- if (readback != ~compare) {
- printf ("%s:%d: FPGA test fail: expected 0x%.8lx" " actual 0x%.8lx\n", __FUNCTION__, __LINE__, ~compare, readback);
- pass = 0;
- break;
- }
- }
- if (!pass)
- break;
- }
- if (!pass)
- break;
- }
- if (pass) {
- printf ("FPGA inverting bus test passed\n");
- print_fpga_revision ();
- } else {
- printf ("** FPGA inverting bus test failed\n");
- }
- return pass;
-}
-
-
-/*
- * Set the active-low FPGA reset signal.
- */
-void fpga_reset (int assert)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
-
- PRINTF ("%s:%d: RESET ", __FUNCTION__, __LINE__);
- if (assert) {
- immap->im_ioport.iop_pcdat &= ~(0x8000 >> FPGA_RESET_BIT_NUM);
- PRINTF ("asserted\n");
- } else {
- immap->im_ioport.iop_pcdat |= (0x8000 >> FPGA_RESET_BIT_NUM);
- PRINTF ("deasserted\n");
- }
-}
-
-
-/*
- * Initialize the SelectMap interface. We assume that the mode and the
- * initial state of all of the port pins have already been set!
- */
-void fpga_selectmap_init (void)
-{
- PRINTF ("%s:%d: Initialize SelectMap interface\n", __FUNCTION__,
- __LINE__);
- fpga_pgm_fn(false, false, 0); /* make sure program pin is inactive */
-}
-
-
-/*
- * Initialize the fpga. Return 1 on success, 0 on failure.
- */
-int gen860t_init_fpga (void)
-{
- int i;
-
- PRINTF ("%s:%d: Initialize FPGA interface\n",
- __FUNCTION__, __LINE__);
- fpga_init ();
- fpga_selectmap_init ();
-
- for (i = 0; i < CONFIG_FPGA_COUNT; i++) {
- PRINTF ("%s:%d: Adding fpga %d\n", __FUNCTION__, __LINE__, i);
- fpga_add (fpga_xilinx, &fpga[i]);
- }
- return 1;
-}
-
-
-/*
- * Set the FPGA's active-low SelectMap program line to the specified level
- */
-int fpga_pgm_fn (int assert, int flush, int cookie)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
-
- PRINTF ("%s:%d: FPGA PROGRAM ", __FUNCTION__, __LINE__);
-
- if (assert) {
- immap->im_ioport.iop_padat &=
- ~(0x8000 >> FPGA_PROGRAM_BIT_NUM);
- PRINTF ("asserted\n");
- } else {
- immap->im_ioport.iop_padat |=
- (0x8000 >> FPGA_PROGRAM_BIT_NUM);
- PRINTF ("deasserted\n");
- }
- return assert;
-}
-
-
-/*
- * Test the state of the active-low FPGA INIT line. Return 1 on INIT
- * asserted (low).
- */
-int fpga_init_fn (int cookie)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
-
- PRINTF ("%s:%d: INIT check... ", __FUNCTION__, __LINE__);
- if (immap->im_cpm.cp_pbdat & (0x80000000 >> FPGA_INIT_BIT_NUM)) {
- PRINTF ("high\n");
- return 0;
- } else {
- PRINTF ("low\n");
- return 1;
- }
-}
-
-
-/*
- * Test the state of the active-high FPGA DONE pin
- */
-int fpga_done_fn (int cookie)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
-
- PRINTF ("%s:%d: DONE check... ", __FUNCTION__, __LINE__);
- if (immap->im_cpm.cp_pbdat & (0x80000000 >> FPGA_DONE_BIT_NUM)) {
- PRINTF ("high\n");
- return FPGA_SUCCESS;
- } else {
- PRINTF ("low\n");
- return FPGA_FAIL;
- }
-}
-
-
-/*
- * Read FPGA SelectMap data.
- */
-int fpga_read_data_fn (unsigned char *data, int cookie)
-{
- vu_char *p = (vu_char *) SELECTMAP_BASE;
-
- *data = *p;
-#if 0
- PRINTF ("%s: Read 0x%x into 0x%p\n", __FUNCTION__, (int) data, data);
-#endif
- return (int) data;
-}
-
-
-/*
- * Write data to the FPGA SelectMap port
- */
-int fpga_write_data_fn (unsigned char data, int flush, int cookie)
-{
- vu_char *p = (vu_char *) SELECTMAP_BASE;
-
-#if 0
- PRINTF ("%s: Write Data 0x%x\n", __FUNCTION__, (int) data);
-#endif
- *p = data;
- return (int) data;
-}
-
-
-/*
- * Abort and FPGA operation
- */
-int fpga_abort_fn (int cookie)
-{
- PRINTF ("%s:%d: FPGA program sequence aborted\n",
- __FUNCTION__, __LINE__);
- return FPGA_FAIL;
-}
-
-
-/*
- * FPGA pre-configuration function. Just make sure that
- * FPGA reset is asserted to keep the FPGA from starting up after
- * configuration.
- */
-int fpga_pre_config_fn (int cookie)
-{
- PRINTF ("%s:%d: FPGA pre-configuration\n", __FUNCTION__, __LINE__);
- fpga_reset(true);
- return 0;
-}
-
-
-/*
- * FPGA post configuration function. Blip the FPGA reset line and then see if
- * the FPGA appears to be running.
- */
-int fpga_post_config_fn (int cookie)
-{
- int rc;
-
- PRINTF ("%s:%d: FPGA post configuration\n", __FUNCTION__, __LINE__);
- fpga_reset(true);
- udelay (1000);
- fpga_reset(false);
- udelay (1000);
-
- /*
- * Use the FPGA,s inverting bus test register to do a simple test of the
- * processor interface.
- */
- rc = test_fpga_ibtr ();
- return rc;
-}
-
-
-/*
- * Clock, chip select and write signal assert functions and error check
- * and busy functions. These are only stubs because the GEN860T selectmap
- * interface handles sequencing of control signals automatically (it uses
- * a memory-mapped interface to the FPGA SelectMap port). The design of
- * the interface guarantees that the SelectMap port cannot be overrun so
- * no busy check is needed. A configuration error is signalled by INIT
- * going low during configuration, so there is no need for a separate error
- * function.
- */
-int fpga_clk_fn (int assert_clk, int flush, int cookie)
-{
- return assert_clk;
-}
-
-int fpga_cs_fn (int assert_cs, int flush, int cookie)
-{
- return assert_cs;
-}
-
-int fpga_wr_fn (int assert_write, int flush, int cookie)
-{
- return assert_write;
-}
-
-int fpga_err_fn (int cookie)
-{
- return 0;
-}
-
-int fpga_busy_fn (int cookie)
-{
- return 0;
-}
-#endif
diff --git a/board/gen860t/fpga.h b/board/gen860t/fpga.h
deleted file mode 100644
index 95c15c4..0000000
--- a/board/gen860t/fpga.h
+++ /dev/null
@@ -1,26 +0,0 @@
-/*
- * (C) Copyright 2002
- * Rich Ireland, Enterasys Networks, rireland@enterasys.com.
- * Keith Outwater, keith_outwater@mvis.com.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * Virtex2 FPGA configuration support for the GEN860T computer
- */
-
-extern int gen860t_init_fpga(void);
-extern int fpga_pgm_fn(int assert_pgm, int flush, int cookie);
-extern int fpga_init_fn(int cookie);
-extern int fpga_err_fn(int cookie);
-extern int fpga_done_fn(int cookie);
-extern int fpga_clk_fn(int assert_clk, int flush, int cookie);
-extern int fpga_cs_fn(int assert_cs, int flush, int cookie);
-extern int fpga_wr_fn(int assert_write, int flush, int cookie);
-extern int fpga_read_data_fn(unsigned char *data, int cookie);
-extern int fpga_write_data_fn(unsigned char data, int flush, int cookie);
-extern int fpga_busy_fn(int cookie);
-extern int fpga_abort_fn(int cookie );
-extern int fpga_pre_config_fn(int cookie );
-extern int fpga_post_config_fn(int cookie );
diff --git a/board/gen860t/gen860t.c b/board/gen860t/gen860t.c
deleted file mode 100644
index fe139f4..0000000
--- a/board/gen860t/gen860t.c
+++ /dev/null
@@ -1,278 +0,0 @@
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- * Keith Outwater, keith_outwater@mvis.com
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <virtex2.h>
-#include <common.h>
-#include <mpc8xx.h>
-#include <asm/8xx_immap.h>
-#include "beeper.h"
-#include "fpga.h"
-#include "ioport.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#ifdef CONFIG_STATUS_LED
-#include <status_led.h>
-#endif
-
-#if defined(CONFIG_CMD_MII) && defined(CONFIG_MII)
-#include <net.h>
-#endif
-
-#if 0
-#define GEN860T_DEBUG
-#endif
-
-#ifdef GEN860T_DEBUG
-#define PRINTF(fmt,args...) printf (fmt ,##args)
-#else
-#define PRINTF(fmt,args...)
-#endif
-
-/*
- * The following UPM init tables were generated automatically by
- * Motorola's MCUINIT program. See the README file for UPM to
- * SDRAM pin assignments if you want to type this data into
- * MCUINIT in order to reverse engineer the waveforms.
- */
-
-/*
- * UPM initialization tables for MICRON MT48LC16M16A2TG SDRAM devices
- * (UPMA) and Virtex FPGA SelectMap interface (UPMB).
- * NOTE that unused areas of the table are used to hold NOP, precharge
- * and mode register set sequences.
- *
- */
-#define UPMA_NOP_ADDR 0x5
-#define UPMA_PRECHARGE_ADDR 0x6
-#define UPMA_MRS_ADDR 0x12
-
-#define UPM_SINGLE_READ_ADDR 0x00
-#define UPM_BURST_READ_ADDR 0x08
-#define UPM_SINGLE_WRITE_ADDR 0x18
-#define UPM_BURST_WRITE_ADDR 0x20
-#define UPM_REFRESH_ADDR 0x30
-
-const uint sdram_upm_table[] = {
- /* single read (offset 0x00 in upm ram) */
- 0x0e0fdc04, 0x01adfc04, 0x0fbffc00, 0x1fff5c05,
- 0xffffffff, 0x0fffffcd, 0x0fff0fce, 0xefcfffff,
- /* burst read (offset 0x08 in upm ram) */
- 0x0f0fdc04, 0x00fdfc04, 0xf0fffc00, 0xf0fffc00,
- 0xf1fffc00, 0xfffffc00, 0xfffffc05, 0xffffffff,
- 0xffffffff, 0xffffffff, 0x0ffffff4, 0x1f3d5ff4,
- 0xfffffff4, 0xfffffff5, 0xffffffff, 0xffffffff,
- /* single write (offset 0x18 in upm ram) */
- 0x0f0fdc04, 0x00ad3c00, 0x1fff5c05, 0xffffffff,
- 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff,
- /* burst write (offset 0x20 in upm ram) */
- 0x0f0fdc00, 0x10fd7c00, 0xf0fffc00, 0xf0fffc00,
- 0xf1fffc04, 0xfffffc05, 0xffffffff, 0xffffffff,
- 0xffffffff, 0xffffffff, 0xffffffff, 0xfffff7ff,
- 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff,
- /* refresh (offset 0x30 in upm ram) */
- 0x1ffddc84, 0xfffffc04, 0xfffffc04, 0xfffffc84,
- 0xfffffc05, 0xffffffff, 0xffffffff, 0xffffffff,
- 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff,
- /* exception (offset 0x3C in upm ram) */
-};
-
-const uint selectmap_upm_table[] = {
- /* single read (offset 0x00 in upm ram) */
- 0x88fffc06, 0x00fff404, 0x00fffc04, 0x33fffc00,
- 0xfffffc05, 0xffffffff, 0xffffffff, 0xffffffff,
- /* burst read (offset 0x08 in upm ram) */
- 0xfffffc04, 0xfffffc05, 0xffffffff, 0xffffffff,
- 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff,
- 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff,
- 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff,
- /* single write (offset 0x18 in upm ram) */
- 0x88fffc04, 0x00fff400, 0x77fffc05, 0xffffffff,
- 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff,
- /* burst write (offset 0x20 in upm ram) */
- 0xfffffc04, 0xfffffc05, 0xffffffff, 0xffffffff,
- 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff,
- 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff,
- 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff,
- /* refresh (offset 0x30 in upm ram) */
- 0xfffffc04, 0xfffffc05, 0xffffffff, 0xffffffff,
- 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff,
- 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff,
- /* exception (offset 0x3C in upm ram) */
- 0xfffffc05, 0xffffffff, 0xffffffff, 0xffffffff
-};
-
-/*
- * Check board identity. Always successful (gives information only)
- */
-int checkboard (void)
-{
- char *s;
- char buf[64];
- int i;
-
- i = getenv_f("board_id", buf, sizeof (buf));
- s = (i > 0) ? buf : NULL;
-
- if (s) {
- printf ("%s ", s);
- } else {
- printf ("<unknown> ");
- }
-
- i = getenv_f("serial#", buf, sizeof (buf));
- s = (i > 0) ? buf : NULL;
-
- if (s) {
- printf ("S/N %s\n", s);
- } else {
- printf ("S/N <unknown>\n");
- }
-
- printf ("CPU at %s MHz, ", strmhz (buf, gd->cpu_clk));
- printf ("local bus at %s MHz\n", strmhz (buf, gd->bus_clk));
- return (0);
-}
-
-/*
- * Initialize SDRAM
- */
-phys_size_t initdram (int board_type)
-{
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immr->im_memctl;
-
- upmconfig (UPMA,
- (uint *) sdram_upm_table,
- sizeof (sdram_upm_table) / sizeof (uint)
- );
-
- /*
- * Setup MAMR register
- */
- memctl->memc_mptpr = CONFIG_SYS_MPTPR_1BK_8K;
- memctl->memc_mamr = CONFIG_SYS_MAMR_8COL & (~(MAMR_PTAE)); /* no refresh yet */
-
- /*
- * Map CS1* to SDRAM bank
- */
- memctl->memc_or1 = CONFIG_SYS_OR1;
- memctl->memc_br1 = CONFIG_SYS_BR1;
-
- /*
- * Perform SDRAM initialization sequence:
- * 1. Apply at least one NOP command
- * 2. 100 uS delay (JEDEC standard says 200 uS)
- * 3. Issue 4 precharge commands
- * 4. Perform two refresh cycles
- * 5. Program mode register
- *
- * Program SDRAM for standard operation, sequential burst, burst length
- * of 4, CAS latency of 2.
- */
- memctl->memc_mar = 0x00000000;
- memctl->memc_mcr = MCR_UPM_A | MCR_OP_RUN | MCR_MB_CS1 |
- MCR_MLCF (0) | UPMA_NOP_ADDR;
- udelay (200);
- memctl->memc_mar = 0x00000000;
- memctl->memc_mcr = MCR_UPM_A | MCR_OP_RUN | MCR_MB_CS1 |
- MCR_MLCF (4) | UPMA_PRECHARGE_ADDR;
-
- memctl->memc_mar = 0x00000000;
- memctl->memc_mcr = MCR_UPM_A | MCR_OP_RUN | MCR_MB_CS1 |
- MCR_MLCF (2) | UPM_REFRESH_ADDR;
-
- memctl->memc_mar = 0x00000088;
- memctl->memc_mcr = MCR_UPM_A | MCR_OP_RUN | MCR_MB_CS1 |
- MCR_MLCF (1) | UPMA_MRS_ADDR;
-
- memctl->memc_mar = 0x00000000;
- memctl->memc_mcr = MCR_UPM_A | MCR_OP_RUN | MCR_MB_CS1 |
- MCR_MLCF (0) | UPMA_NOP_ADDR;
- /*
- * Enable refresh
- */
- memctl->memc_mamr |= MAMR_PTAE;
-
- return (SDRAM_SIZE);
-}
-
-/*
- * Disk On Chip (DOC) Millenium initialization.
- * The DOC lives in the CS2* space
- */
-#if defined(CONFIG_CMD_DOC)
-void doc_init (void)
-{
- printf ("Probing at 0x%.8x: ", DOC_BASE);
- doc_probe (DOC_BASE);
-}
-#endif
-
-/*
- * Miscellaneous intialization
- */
-int misc_init_r (void)
-{
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immr->im_memctl;
-
- /*
- * Set up UPMB to handle the Virtex FPGA SelectMap interface
- */
- upmconfig (UPMB, (uint *) selectmap_upm_table,
- sizeof (selectmap_upm_table) / sizeof (uint));
-
- memctl->memc_mbmr = 0x0;
-
- config_mpc8xx_ioports (immr);
-
-#if defined(CONFIG_CMD_MII)
- mii_init ();
-#endif
-
-#if defined(CONFIG_FPGA)
- gen860t_init_fpga ();
-#endif
- return 0;
-}
-
-/*
- * Final init hook before entering command loop.
- */
-int last_stage_init (void)
-{
-#if !defined(CONFIG_SC)
- char buf[256];
- int i;
-
- /*
- * Turn the beeper volume all the way down in case this is a warm boot.
- */
- set_beeper_volume (-64);
- init_beeper ();
-
- /*
- * Read the environment to see what to do with the beeper
- */
- i = getenv_f("beeper", buf, sizeof (buf));
- if (i > 0) {
- do_beeper (buf);
- }
-#endif
- return 0;
-}
-
-/*
- * Stub to make POST code happy. Can't self-poweroff, so just hang.
- */
-void board_poweroff (void)
-{
- puts ("### Please power off the board ###\n");
- while (1);
-}
diff --git a/board/gen860t/ioport.c b/board/gen860t/ioport.c
deleted file mode 100644
index 7cd209b..0000000
--- a/board/gen860t/ioport.c
+++ /dev/null
@@ -1,331 +0,0 @@
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc8xx.h>
-#include <asm/8xx_immap.h>
-#include "ioport.h"
-
-#if 0
-#define IOPORT_DEBUG
-#endif
-
-#ifdef IOPORT_DEBUG
-#define PRINTF(fmt,args...) printf (fmt ,##args)
-#else
-#define PRINTF(fmt,args...)
-#endif
-
-/*
- * The ioport configuration table.
- */
-const mpc8xx_iop_conf_t iop_conf_tab[NUM_PORTS][PORT_BITS] = {
- /*
- * Port A configuration
- * Pin Signal Type Active Initial state
- * PA7 fpgaProgramLowOut Out Low High
- * PA1 fpgaCoreVoltageFailLow In Low N/A
- */
- { /* conf ppar psor pdir podr pdat pint function */
- /* N/A */ { 0, 0, 0, 0, 0, 0, 0 }, /* No pin */
- /* N/A */ { 0, 0, 0, 0, 0, 0, 0 }, /* No pin */
- /* PA15 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PA14 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PA13 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PA12 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PA11 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PA10 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PA9 */ { 1, 0, 0, 1, 0, 0, 0 }, /* grn bicolor LED 1*/
- /* PA8 */ { 1, 0, 0, 1, 0, 0, 0 }, /* red bicolor LED 1*/
- /* PA7 */ { 1, 0, 0, 1, 0, 1, 0 }, /* fpgaProgramLow */
- /* PA6 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PA5 */ { 1, 0, 0, 1, 0, 0, 0 }, /* grn bicolor LED 0*/
- /* PA4 */ { 1, 0, 0, 1, 0, 0, 0 }, /* red bicolor LED 0*/
- /* PA3 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PA2 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
-#if !defined(CONFIG_SC)
- /* PA1 */ { 1, 0, 0, 0, 0, 0, 0 }, /* fpgaCoreVoltageFail*/
-#else
- /* PA1 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
-#endif
- /* PA0 */ { 0, 0, 0, 0, 0, 0, 0 } /* */
- },
-
- /*
- * Port B configuration
- * Pin Signal Type Active Initial state
- * PB14 docBusyLowIn In Low X
- * PB15 gpio1Sig Out High Low
- * PB16 fpgaDoneBi In High X
- * PB17 swBitOkLowOut Out Low High
- * PB19 speakerVolSig Out/Hi-Z High/Low High (Hi-Z)
- * PB22 fpgaInitLowBi In Low X
- * PB23 batteryOkSig In High X
- * PB31 pulseCatcherClr Out High 0
- */
- { /* conf ppar psor pdir podr pdat pint function */
-#if !defined(CONFIG_SC)
- /* PB31 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
-#else
- /* PB31 */ { 1, 0, 0, 1, 0, 0, 0 }, /* pulseCatcherClr */
-#endif
- /* PB30 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PB29 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PB28 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PB27 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PB26 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PB25 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PB24 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
-#if !defined(CONFIG_SC)
- /* PB23 */ { 1, 0, 0, 0, 0, 0, 0 }, /* batteryOk */
-#else
- /* PB23 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
-#endif
- /* PB22 */ { 1, 0, 0, 0, 0, 0, 0 }, /* fpgaInitLowBi */
- /* PB21 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PB20 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
-#if !defined(CONFIG_SC)
- /* PB19 */ { 1, 0, 0, 1, 1, 1, 0 }, /* speakerVol */
-#else
- /* PB19 */ { 0, 0, 0, 1, 1, 1, 0 }, /* */
-#endif
- /* PB18 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PB17 */ { 1, 0, 0, 1, 0, 1, 0 }, /* swBitOkLow */
- /* PB16 */ { 1, 0, 0, 0, 0, 0, 0 }, /* fpgaDone */
- /* PB15 */ { 1, 0, 0, 1, 0, 0, 0 }, /* gpio1 */
-#if !defined(CONFIG_SC)
- /* PB14 */ { 1, 0, 0, 0, 0, 0, 0 } /* docBusyLow */
-#else
- /* PB14 */ { 0, 0, 0, 0, 0, 0, 0 } /* */
-#endif
- },
-
- /*
- * Port C configuration
- * Pin Signal Type Active Initial state
- * PC4 i2cBus1EnSig Out High High
- * PC5 i2cBus2EnSig Out High High
- * PC6 gpio0Sig Out High Low
- * PC8 i2cBus3EnSig Out High High
- * PC10 i2cBus4EnSig Out High High
- * PC11 fpgaResetLowOut Out Low High
- * PC12 systemBitOkIn In High X
- * PC15 selfDreqLow In Low X
- */
- { /* conf ppar psor pdir podr pdat pint function */
- /* N/A */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* N/A */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PC15 */ { 1, 0, 0, 0, 0, 0, 0 }, /* selfDreqLowIn */
- /* PC14 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PC13 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
-#if !defined(CONFIG_SC)
- /* PC12 */ { 1, 0, 0, 0, 0, 0, 0 }, /* systemBitOkIn */
-#else
- /* PC12 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
-#endif
- /* PC11 */ { 1, 0, 0, 1, 0, 1, 0 }, /* fpgaResetLowOut */
-#if !defined(CONFIG_SC)
- /* PC10 */ { 1, 0, 0, 1, 0, 1, 0 }, /* i2cBus4EnSig */
-#else
- /* PC10 */ { 0, 0, 0, 1, 0, 1, 0 }, /* */
-#endif
- /* PC9 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
-#if !defined(CONFIG_SC)
- /* PC8 */ { 1, 0, 0, 1, 0, 1, 0 }, /* i2cBus3EnSig */
-#else
- /* PC8 */ { 0, 0, 0, 1, 0, 1, 0 }, /* */
-#endif
- /* PC7 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PC6 */ { 1, 0, 0, 1, 0, 1, 0 }, /* gpio0 */
-#if !defined(CONFIG_SC)
- /* PC5 */ { 1, 0, 0, 1, 0, 1, 0 }, /* i2cBus2EnSig */
- /* PC4 */ { 1, 0, 0, 1, 0, 1, 0 }, /* i2cBus1EnSig */
-#else
- /* PC5 */ { 0, 0, 0, 1, 0, 1, 0 }, /* */
- /* PC4 */ { 0, 0, 0, 1, 0, 1, 0 }, /* */
-#endif
- /* N/A */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* N/A */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* N/A */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* N/A */ { 0, 0, 0, 0, 0, 0, 0 } /* */
- },
-
- /*
- * Port D configuration
- */
- { /* conf ppar psor pdir podr pdat pint function */
- /* N/A */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* N/A */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PD15 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PD14 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PD13 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PD12 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PD11 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PD10 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PD9 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PD8 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PD7 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PD6 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PD5 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PD4 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* PD3 */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* N/A */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* N/A */ { 0, 0, 0, 0, 0, 0, 0 }, /* */
- /* N/A */ { 0, 0, 0, 0, 0, 0, 0 } /* */
- }
-};
-
-/*
- * Configure the MPC8XX I/O ports per the ioport configuration table
- * (taken from ./arch/powerpc/cpu/mpc8260/cpu_init.c)
- */
-void config_mpc8xx_ioports (volatile immap_t * immr)
-{
- int portnum;
-
- for (portnum = 0; portnum < NUM_PORTS; portnum++) {
- uint pmsk = 0, ppar = 0, psor = 0, pdir = 0;
- uint podr = 0, pdat = 0, pint = 0;
- uint msk = 1;
- mpc8xx_iop_conf_t *iopc =
- (mpc8xx_iop_conf_t *) & iop_conf_tab[portnum][0];
- mpc8xx_iop_conf_t *eiopc = iopc + PORT_BITS;
-
- /*
- * For all ports except port B, ignore the two don't care entries
- * in the configuration tables.
- */
- if (portnum != 1) {
- iopc = (mpc8xx_iop_conf_t *) &
- iop_conf_tab[portnum][2];
- }
-
- /*
- * NOTE: index 0 refers to pin 17, index 17 refers to pin 0
- */
- while (iopc < eiopc) {
- if (iopc->conf) {
- pmsk |= msk;
- if (iopc->ppar)
- ppar |= msk;
- if (iopc->psor)
- psor |= msk;
- if (iopc->pdir)
- pdir |= msk;
- if (iopc->podr)
- podr |= msk;
- if (iopc->pdat)
- pdat |= msk;
- if (iopc->pint)
- pint |= msk;
- }
- msk <<= 1;
- iopc++;
- }
-
- PRINTF ("%s:%d:\n portnum=%d ", __FUNCTION__, __LINE__,
- portnum);
-#ifdef IOPORT_DEBUG
- switch (portnum) {
- case 0:
- printf ("(A)\n");
- break;
- case 1:
- printf ("(B)\n");
- break;
- case 2:
- printf ("(C)\n");
- break;
- case 3:
- printf ("(D)\n");
- break;
- default:
- printf ("(?)\n");
- break;
- }
-#endif
- PRINTF (" ppar=0x%.8x pdir=0x%.8x podr=0x%.8x\n"
- " pdat=0x%.8x psor=0x%.8x pint=0x%.8x pmsk=0x%.8x\n",
- ppar, pdir, podr, pdat, psor, pint, pmsk);
-
- /*
- * Have to handle the ioports on a port-by-port basis since there
- * are three different flavors.
- */
- if (pmsk != 0) {
- uint tpmsk = ~pmsk;
-
- if (0 == portnum) { /* port A */
- immr->im_ioport.iop_papar &= tpmsk;
- immr->im_ioport.iop_padat =
- (immr->im_ioport.
- iop_padat & tpmsk) | pdat;
- immr->im_ioport.iop_padir =
- (immr->im_ioport.
- iop_padir & tpmsk) | pdir;
- immr->im_ioport.iop_paodr =
- (immr->im_ioport.
- iop_paodr & tpmsk) | podr;
- immr->im_ioport.iop_papar |= ppar;
- } else if (1 == portnum) { /* port B */
- immr->im_cpm.cp_pbpar &= tpmsk;
- immr->im_cpm.cp_pbdat =
- (immr->im_cpm.
- cp_pbdat & tpmsk) | pdat;
- immr->im_cpm.cp_pbdir =
- (immr->im_cpm.
- cp_pbdir & tpmsk) | pdir;
- immr->im_cpm.cp_pbodr =
- (immr->im_cpm.
- cp_pbodr & tpmsk) | podr;
- immr->im_cpm.cp_pbpar |= ppar;
- } else if (2 == portnum) { /* port C */
- immr->im_ioport.iop_pcpar &= tpmsk;
- immr->im_ioport.iop_pcdat =
- (immr->im_ioport.
- iop_pcdat & tpmsk) | pdat;
- immr->im_ioport.iop_pcdir =
- (immr->im_ioport.
- iop_pcdir & tpmsk) | pdir;
- immr->im_ioport.iop_pcint =
- (immr->im_ioport.
- iop_pcint & tpmsk) | pint;
- immr->im_ioport.iop_pcso =
- (immr->im_ioport.
- iop_pcso & tpmsk) | psor;
- immr->im_ioport.iop_pcpar |= ppar;
- } else if (3 == portnum) { /* port D */
- immr->im_ioport.iop_pdpar &= tpmsk;
- immr->im_ioport.iop_pddat =
- (immr->im_ioport.
- iop_pddat & tpmsk) | pdat;
- immr->im_ioport.iop_pddir =
- (immr->im_ioport.
- iop_pddir & tpmsk) | pdir;
- immr->im_ioport.iop_pdpar |= ppar;
- }
- }
- }
-
- PRINTF ("%s:%d: Port A:\n papar=0x%.4x padir=0x%.4x"
- " paodr=0x%.4x\n padat=0x%.4x\n", __FUNCTION__, __LINE__,
- immr->im_ioport.iop_papar, immr->im_ioport.iop_padir,
- immr->im_ioport.iop_paodr, immr->im_ioport.iop_padat);
- PRINTF ("%s:%d: Port B:\n pbpar=0x%.8x pbdir=0x%.8x"
- " pbodr=0x%.8x\n pbdat=0x%.8x\n", __FUNCTION__, __LINE__,
- immr->im_cpm.cp_pbpar, immr->im_cpm.cp_pbdir,
- immr->im_cpm.cp_pbodr, immr->im_cpm.cp_pbdat);
- PRINTF ("%s:%d: Port C:\n pcpar=0x%.4x pcdir=0x%.4x"
- " pcdat=0x%.4x\n pcso=0x%.4x pcint=0x%.4x\n ",
- __FUNCTION__, __LINE__, immr->im_ioport.iop_pcpar,
- immr->im_ioport.iop_pcdir, immr->im_ioport.iop_pcdat,
- immr->im_ioport.iop_pcso, immr->im_ioport.iop_pcint);
- PRINTF ("%s:%d: Port D:\n pdpar=0x%.4x pddir=0x%.4x"
- " pddat=0x%.4x\n", __FUNCTION__, __LINE__,
- immr->im_ioport.iop_pdpar, immr->im_ioport.iop_pddir,
- immr->im_ioport.iop_pddat);
-}
diff --git a/board/gen860t/ioport.h b/board/gen860t/ioport.h
deleted file mode 100644
index 4ac2aa4..0000000
--- a/board/gen860t/ioport.h
+++ /dev/null
@@ -1,26 +0,0 @@
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- * Keith Outwater, keith_outwater@mvis.com
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#define NUM_PORTS 4
-#define PORT_BITS 18
-
-/*
- * This structure provides configuration information for one port pin.
- * We include all fields needed to initialize any of the ioports.
- */
-typedef struct {
- unsigned char conf:1; /* If 1, configure this port */
- unsigned char ppar:1; /* Port Pin Assignment Register */
- unsigned char psor:1; /* Port Special Options Register */
- unsigned char pdir:1; /* Port Data Direction Register */
- unsigned char podr:1; /* Port Open Drain Register */
- unsigned char pdat:1; /* Port Data Register */
- unsigned char pint:1; /* Port Interrupt Register */
-} mpc8xx_iop_conf_t;
-
-extern void config_mpc8xx_ioports(volatile immap_t *immr);
diff --git a/board/gen860t/u-boot-flashenv.lds b/board/gen860t/u-boot-flashenv.lds
deleted file mode 100644
index 7a4a763..0000000
--- a/board/gen860t/u-boot-flashenv.lds
+++ /dev/null
@@ -1,92 +0,0 @@
-/*
- * Linker command file for the GEN860T board when the environment is
- * stored in flash memory.
- *
- * (C) Copyright 2000-2010
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-SECTIONS
-{
- /*
- * Read-only sections, merged into text segment:
- */
- . = + SIZEOF_HEADERS;
- .text :
- {
- arch/powerpc/cpu/mpc8xx/start.o (.text*)
- arch/powerpc/cpu/mpc8xx/traps.o (.text*)
-
- *(.text*)
- }
- _etext = .;
- PROVIDE (etext = .);
- .rodata :
- {
- *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
- }
-
- /*
- * Read-write section, merged into data segment:
- */
- . = (. + 0x00FF) & 0xFFFFFF00;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- KEEP(*(.got))
- _GOT2_TABLE_ = .;
- KEEP(*(.got2))
- _FIXUP_TABLE_ = .;
- KEEP(*(.fixup))
- }
- __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
- __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
- .data:
- {
- *(.data*)
- *(.sdata*)
- }
- _edata = .;
- PROVIDE (edata = .);
-
- . = .;
-
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
- . = .;
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(256);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(256);
- __init_end = .;
-
- __bss_start = .;
- .bss (NOLOAD) :
- {
- *(.bss*)
- *(.sbss*)
- *(COMMON)
- . = ALIGN(4);
- }
-
- __bss_end = . ;
- PROVIDE (end = .);
-
- .ppcenv:
- {
- . = env_offset;
- common/env_embedded.o
- }
-}
diff --git a/board/gen860t/u-boot.lds b/board/gen860t/u-boot.lds
deleted file mode 100644
index 3371c0a..0000000
--- a/board/gen860t/u-boot.lds
+++ /dev/null
@@ -1,87 +0,0 @@
-/*
- * Linker command file for the GEN860T board.
- *
- * (C) Copyright 2000-2010
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-SECTIONS
-{
- /*
- * Read-only sections, merged into text segment:
- */
- . = + SIZEOF_HEADERS;
- .text :
- {
- arch/powerpc/cpu/mpc8xx/start.o (.text*)
- arch/powerpc/cpu/mpc8xx/traps.o (.text*)
-
- *(.text*)
- }
- _etext = .;
- PROVIDE (etext = .);
- .rodata :
- {
- *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
- }
-
- /*
- * Read-write section, merged into data segment:
- */
- . = (. + 0x00FF) & 0xFFFFFF00;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- _GOT2_TABLE_ = .;
- KEEP(*(.got2))
- KEEP(*(.got))
- PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4);
- _FIXUP_TABLE_ = .;
- KEEP(*(.fixup))
- }
- __got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1;
- __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
- .data :
- {
- *(.data*)
- *(.sdata*)
- }
- _edata = .;
- PROVIDE (edata = .);
-
- . = .;
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
-
- . = .;
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(256);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(256);
- __init_end = .;
-
- __bss_start = .;
- .bss (NOLOAD) :
- {
- *(.bss*)
- *(.sbss*)
- *(COMMON)
- . = ALIGN(4);
- }
- __bss_end = . ;
- PROVIDE (end = .);
-}