summaryrefslogtreecommitdiff
path: root/doc/README.m5475evb
diff options
context:
space:
mode:
Diffstat (limited to 'doc/README.m5475evb')
-rw-r--r--doc/README.m5475evb94
1 files changed, 47 insertions, 47 deletions
diff --git a/doc/README.m5475evb b/doc/README.m5475evb
index cec4fd0..37d1438 100644
--- a/doc/README.m5475evb
+++ b/doc/README.m5475evb
@@ -106,8 +106,8 @@ CFG_I2C_SLAVE -- define for I2C slave address
CFG_I2C_OFFSET -- define for I2C base address offset
CFG_IMMR -- define for MBAR offset
-CONFIG_PCI -- define for PCI support
-CONFIG_PCI_PNP -- define for Plug n play support
+CONFIG_PCI -- define for PCI support
+CONFIG_PCI_PNP -- define for Plug n play support
CONFIG_SKIPPCI_HOSTBRIDGE -- SKIP PCI Host bridge
CFG_PCI_MEM_BUS -- PCI memory logical offset
CFG_PCI_MEM_PHYS -- PCI memory physical offset
@@ -143,7 +143,7 @@ CFG_SDRAM_BASE -- defines the DRAM Base
3. COMPILATION
==============
3.1 To create U-Boot the gcc-4.x compiler set (ColdFire ELF or uclinux
- version) from codesourcery.com was used. Download it from:
+ version) from codesourcery.com was used. Download it from:
http://www.codesourcery.com/gnu_toolchains/coldfire/download.html
3.2 Compilation
@@ -206,68 +206,68 @@ flashsize = 0x01200000
flashoffset = 0x00000000
sramstart = 0xF2000000
sramsize = 0x00001000
-mbar = 0xF0000000
+mbar = 0xF0000000
busfreq = 133.333 MHz
-pcifreq = 0 MHz
+pcifreq = 0 MHz
ethaddr = 00:E0:0C:BC:E5:60
eth1addr = 00:E0:0C:BC:E5:61
ip_addr = 192.162.1.2
baudrate = 115200 bps
-> ?
-? - alias for 'help'
+? - alias for 'help'
autoscr - run script from memory
-base - print or set address offset
-bdinfo - print Board Info structure
-boot - boot default, i.e., run 'bootcmd'
-bootd - boot default, i.e., run 'bootcmd'
+base - print or set address offset
+bdinfo - print Board Info structure
+boot - boot default, i.e., run 'bootcmd'
+bootd - boot default, i.e., run 'bootcmd'
bootelf - Boot from an ELF image in memory
-bootm - boot application image from memory
+bootm - boot application image from memory
bootp - boot image via network using BootP/TFTP protocol
-bootvx - Boot vxWorks from an ELF image
-cmp - memory compare
+bootvx - Boot vxWorks from an ELF image
+cmp - memory compare
coninfo - print console devices and information
-cp - memory copy
-crc32 - checksum calculation
-dcache - enable or disable data cache
-echo - echo args to console
-erase - erase FLASH memory
-flinfo - print FLASH memory information
-go - start application at address 'addr'
-help - print online help
-icache - enable or disable instruction cache
-icrc32 - checksum calculation
-iloop - infinite loop on address range
-imd - i2c memory display
-iminfo - print header information for application image
-imls - list all images found in flash
-imm - i2c memory modify (auto-incrementing)
-imw - memory write (fill)
-inm - memory modify (constant address)
-iprobe - probe to discover valid I2C chip addresses
+cp - memory copy
+crc32 - checksum calculation
+dcache - enable or disable data cache
+echo - echo args to console
+erase - erase FLASH memory
+flinfo - print FLASH memory information
+go - start application at address 'addr'
+help - print online help
+icache - enable or disable instruction cache
+icrc32 - checksum calculation
+iloop - infinite loop on address range
+imd - i2c memory display
+iminfo - print header information for application image
+imls - list all images found in flash
+imm - i2c memory modify (auto-incrementing)
+imw - memory write (fill)
+inm - memory modify (constant address)
+iprobe - probe to discover valid I2C chip addresses
itest - return true/false on integer compare
-loadb - load binary file over serial line (kermit mode)
-loads - load S-Record file over serial line
-loady - load binary file over serial line (ymodem mode)
-loop - infinite loop on address range
-md - memory display
-mii - MII utility commands
-mm - memory modify (auto-incrementing)
-mtest - simple RAM test
-mw - memory write (fill)
+loadb - load binary file over serial line (kermit mode)
+loads - load S-Record file over serial line
+loady - load binary file over serial line (ymodem mode)
+loop - infinite loop on address range
+md - memory display
+mii - MII utility commands
+mm - memory modify (auto-incrementing)
+mtest - simple RAM test
+mw - memory write (fill)
nfs - boot image via network using NFS protocol
-nm - memory modify (constant address)
-pci - list and access PCI Configuration Space
+nm - memory modify (constant address)
+pci - list and access PCI Configuration Space
ping - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
-reset - Perform RESET of the CPU
-run - run commands in an environment variable
+reset - Perform RESET of the CPU
+run - run commands in an environment variable
saveenv - save environment variables to persistent storage
-setenv - set environment variables
-sleep - delay execution for some time
+setenv - set environment variables
+sleep - delay execution for some time
tftpboot- boot image via network using TFTP protocol
-usb - USB sub-system
+usb - USB sub-system
usbboot - boot from USB device
version - print monitor version
-> usb start