diff options
Diffstat (limited to 'include/configs/PATI.h')
| -rw-r--r-- | include/configs/PATI.h | 245 |
1 files changed, 0 insertions, 245 deletions
diff --git a/include/configs/PATI.h b/include/configs/PATI.h deleted file mode 100644 index 1f26ac4..0000000 --- a/include/configs/PATI.h +++ /dev/null @@ -1,245 +0,0 @@ -/* - * (C) Copyright 2003 - * Denis Peter d.peter@mpl.ch - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * File: PATI.h - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ - -#define CONFIG_MPC555 1 /* This is an MPC555 CPU */ -#define CONFIG_PATI 1 /* ...On a PATI board */ - -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 - -/* Serial Console Configuration */ -#define CONFIG_5xx_CONS_SCI1 -#undef CONFIG_5xx_CONS_SCI2 - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* - * Command line configuration. - */ -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_REGINFO - -#define CONFIG_BOOTCOMMAND "" /* autoboot command */ - -#define CONFIG_BOOTARGS "" /* */ - -#define CONFIG_WATCHDOG /* turn on platform specific watchdog */ - -#define CONFIG_LOADS_ECHO 1 /* Echo on for serial download */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_PREBOOT - -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00010000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00A00000 /* 10 MB in SRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 1250000 } - -/*********************************************************************** - * Last Stage Init - ***********************************************************************/ -#define CONFIG_LAST_STAGE_INIT - -/* - * Low Level Configuration Settings - */ - -/* - * Internal Memory Mapped (This is not the IMMR content) - */ -#define CONFIG_SYS_IMMR 0x01C00000 /* Physical start adress of internal memory map */ - -/* - * Definitions for initial stack pointer and data area - */ -#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_IMMR + 0x003f9800) /* Physical start adress of internal MPC555 writable RAM */ -#define CONFIG_SYS_INIT_RAM_SIZE (CONFIG_SYS_IMMR + 0x003fffff) /* Physical end adress of internal MPC555 used RAM area */ -#define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - CONFIG_SYS_INIT_RAM_ADDR) - GENERATED_GBL_DATA_SIZE) /* Offset from the beginning of ram */ -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_IMMR + 0x03fa000) /* Physical start adress of inital stack */ -/* - * Start addresses for the final memory configuration - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* Monitor won't change memory map */ -#define CONFIG_SYS_FLASH_BASE 0xffC00000 /* External flash */ -#define PCI_BASE 0x03000000 /* PCI Base (CS2) */ -#define PCI_CONFIG_BASE 0x04000000 /* PCI & PLD (CS3) */ -#define PLD_CONFIG_BASE 0x04001000 /* PLD (CS3) */ - -#define CONFIG_SYS_MONITOR_BASE 0xFFF00000 -/* CONFIG_SYS_FLASH_BASE */ /* CONFIG_SYS_TEXT_BASE is defined in the board config.mk file. */ - /* This adress is given to the linker with -Ttext to */ - /* locate the text section at this adress. */ -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 192 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ - -#define CONFIG_SYS_RESET_ADDRESS (PLD_CONFIG_BASE + 0x10) /* Adress which causes reset */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH organization - *----------------------------------------------------------------------- - * - */ - -#define CONFIG_SYS_FLASH_PROTECTION -#define CONFIG_SYS_FLASH_EMPTY_INFO - -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_FLASH_CFI_DRIVER - -#define CONFIG_FLASH_SHOW_PROGRESS 45 - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_MAX_FLASH_SECT 128 - -#define CONFIG_ENV_IS_IN_EEPROM -#ifdef CONFIG_ENV_IS_IN_EEPROM -#define CONFIG_ENV_OFFSET 0 -#define CONFIG_ENV_SIZE 2048 -#endif - -#undef CONFIG_ENV_IS_IN_FLASH -#ifdef CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_SIZE 0x00002000 /* Set whole sector as env */ -#define CONFIG_ENV_OFFSET ((0 - CONFIG_SYS_FLASH_BASE) - CONFIG_ENV_SIZE) /* Environment starts at this adress */ -#endif - -#define CONFIG_SPI 1 -#define CONFIG_SYS_SPI_CS_USED 0x09 /* CS0 and CS3 are used */ -#define CONFIG_SYS_SPI_CS_BASE 0x08 /* CS3 is active low */ -#define CONFIG_SYS_SPI_CS_ACT 0x00 /* CS3 is active low */ -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * SW Watchdog freeze - */ -#undef CONFIG_WATCHDOG -#if defined(CONFIG_WATCHDOG) -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ - SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) -#else -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ - SYPCR_SWP) -#endif /* CONFIG_WATCHDOG */ - -/*----------------------------------------------------------------------- - * TBSCR - Time Base Status and Control - *----------------------------------------------------------------------- - * Clear Reference Interrupt Status, Timebase freezing enabled - */ -#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled - */ -#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) - -/*----------------------------------------------------------------------- - * SCCR - System Clock and reset Control Register - *----------------------------------------------------------------------- - * Set clock output, timebase and RTC source and divider, - * power management and some other internal clocks - */ -#define SCCR_MASK SCCR_EBDF00 -#define CONFIG_SYS_SCCR (SCCR_TBS | SCCR_RTDIV | SCCR_RTSEL | \ - SCCR_COM01 | SCCR_DFNL000 | SCCR_DFNH000) - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration - *----------------------------------------------------------------------- - * Data show cycle - */ -#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_EARB | SIUMCR_GPC01 | SIUMCR_MLRC11) /* Disable data show cycle */ - -/*----------------------------------------------------------------------- - * PLPRCR - PLL, Low-Power, and Reset Control Register - *----------------------------------------------------------------------- - * Set all bits to 40 Mhz - * - */ -#define CONFIG_SYS_OSC_CLK ((uint)4000000) /* Oscillator clock is 4MHz */ - -#define CONFIG_SYS_PLPRCR (PLPRCR_MF_9 | PLPRCR_DIVF_0) - -/*----------------------------------------------------------------------- - * UMCR - UIMB Module Configuration Register - *----------------------------------------------------------------------- - * - */ -#define CONFIG_SYS_UMCR (UMCR_FSPEED) /* IMB clock same as U-bus */ - -/*----------------------------------------------------------------------- - * ICTRL - I-Bus Support Control Register - */ -#define CONFIG_SYS_ICTRL (ICTRL_ISCT_SER_7) /* Take out of serialized mode */ - -/*----------------------------------------------------------------------- - * USIU - Memory Controller Register - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | BR_V | BR_BI | BR_PS_16 | BR_SETA) -#define CONFIG_SYS_OR0_PRELIM (0xffc00000) /* SCY is not used if external TA is set */ -/* SDRAM */ -#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_SDRAM_BASE | BR_V | BR_BI | BR_PS_32 | BR_SETA) -#define CONFIG_SYS_OR1_PRELIM (OR_ADDR_MK_FF) /* SCY is not used if external TA is set */ -/* PCI */ -#define CONFIG_SYS_BR2_PRELIM (PCI_BASE | BR_V | BR_PS_32 | BR_SETA) -#define CONFIG_SYS_OR2_PRELIM (OR_ADDR_MK_FF) -/* config registers: */ -#define CONFIG_SYS_BR3_PRELIM (PCI_CONFIG_BASE | BR_V | BR_BI | BR_PS_32 | BR_SETA) -#define CONFIG_SYS_OR3_PRELIM (0xffff0000) - -#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* We don't realign the flash */ - -/*----------------------------------------------------------------------- - * DER - Timer Decrementer - *----------------------------------------------------------------------- - * Initialise to zero - */ -#define CONFIG_SYS_DER 0x00000000 - -#endif /* __CONFIG_H */ |