summaryrefslogtreecommitdiff
path: root/include/configs/TOP860.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs/TOP860.h')
-rw-r--r--include/configs/TOP860.h284
1 files changed, 142 insertions, 142 deletions
diff --git a/include/configs/TOP860.h b/include/configs/TOP860.h
index f902685..535ec79 100644
--- a/include/configs/TOP860.h
+++ b/include/configs/TOP860.h
@@ -25,15 +25,15 @@
* MA 02111-1307 USA
*/
/*
- * TOP860 is a simple module:
- * 16-bit wide FLASH on CS0 (2MB or more)
- * 32-bit wide DRAM on CS2 (either 4MB or 16MB)
- * FEC with Am79C874 100-Base-T and Fiber Optic
- * Ports available, but we choose SMC1 for Console
+ * TOP860 is a simple module:
+ * 16-bit wide FLASH on CS0 (2MB or more)
+ * 32-bit wide DRAM on CS2 (either 4MB or 16MB)
+ * FEC with Am79C874 100-Base-T and Fiber Optic
+ * Ports available, but we choose SMC1 for Console
* 8k I2C EEPROM at address 0xae, 6k user available, 2k factory set
- * 32768Hz crystal PLL set for 49.152MHz Core and 24.576MHz Bus Clock
- *
- * This config has been copied from MBX.h / MBX860T.h
+ * 32768Hz crystal PLL set for 49.152MHz Core and 24.576MHz Bus Clock
+ *
+ * This config has been copied from MBX.h / MBX860T.h
*/
/*
* board/config.h - configuration options, board specific
@@ -54,36 +54,36 @@
#define CONFIG_MPC860T 1 /* even better... an FEC! */
#define CONFIG_TOP860 1 /* ...on a TOP860 module */
#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_IDENT_STRING " EMK TOP860"
+#define CONFIG_IDENT_STRING " EMK TOP860"
/*-----------------------------------------------------------------------
* CLOCK settings
*/
-#define CONFIG_SYSCLK 49152000
-#define CFG_XTAL 32768
-#define CONFIG_EBDF 1
-#define CONFIG_COM 3
-#define CONFIG_RTC_MPC8xx
-
+#define CONFIG_SYSCLK 49152000
+#define CFG_XTAL 32768
+#define CONFIG_EBDF 1
+#define CONFIG_COM 3
+#define CONFIG_RTC_MPC8xx
+
/*-----------------------------------------------------------------------
* Physical memory map as defined by EMK
*/
#define CFG_IMMR 0xFFF00000 /* Internal Memory Mapped Register */
-#define CFG_FLASH_BASE 0x80000000 /* FLASH in final mapping */
-#define CFG_DRAM_BASE 0x00000000 /* DRAM in final mapping */
-#define CFG_FLASH_MAX 0x00400000 /* max FLASH to expect */
-#define CFG_DRAM_MAX 0x01000000 /* max DRAM to expect */
-
+#define CFG_FLASH_BASE 0x80000000 /* FLASH in final mapping */
+#define CFG_DRAM_BASE 0x00000000 /* DRAM in final mapping */
+#define CFG_FLASH_MAX 0x00400000 /* max FLASH to expect */
+#define CFG_DRAM_MAX 0x01000000 /* max DRAM to expect */
+
/*-----------------------------------------------------------------------
* derived values
*/
-#define CFG_MF (CONFIG_SYSCLK/CFG_XTAL)
-#define CFG_CPUCLOCK CONFIG_SYSCLK
-#define CFG_BRGCLOCK CONFIG_SYSCLK
-#define CFG_BUSCLOCK (CONFIG_SYSCLK >> CONFIG_EBDF)
+#define CFG_MF (CONFIG_SYSCLK/CFG_XTAL)
+#define CFG_CPUCLOCK CONFIG_SYSCLK
+#define CFG_BRGCLOCK CONFIG_SYSCLK
+#define CFG_BUSCLOCK (CONFIG_SYSCLK >> CONFIG_EBDF)
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-#define CONFIG_8xx_GCLK_FREQ CONFIG_SYSCLK
-
+#define CONFIG_8xx_GCLK_FREQ CONFIG_SYSCLK
+
/*-----------------------------------------------------------------------
* FLASH organization
*/
@@ -92,8 +92,8 @@
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#define CFG_FLASH_CFI
+
+#define CFG_FLASH_CFI
/*-----------------------------------------------------------------------
* Command interpreter
@@ -101,7 +101,7 @@
#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
#undef CONFIG_8xx_CONS_SMC2
#define CONFIG_BAUDRATE 9600
-
+
/*
* Allow partial commands to be matched to uniqueness.
*/
@@ -125,8 +125,8 @@
CFG_CMD_BEDBUG \
)
-#define CONFIG_AUTOSCRIPT 1
-#define CFG_LOADS_BAUD_CHANGE 1
+#define CONFIG_AUTOSCRIPT 1
+#define CFG_LOADS_BAUD_CHANGE 1
#undef CONFIG_LOADS_ECHO /* NO echo on for serial download */
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
@@ -134,19 +134,19 @@
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-
+
#undef CFG_HUSH_PARSER /* Hush parse for U-Boot */
-
+
#ifdef CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
-
+
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-
+
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
@@ -156,63 +156,63 @@
*/
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
+
/*-----------------------------------------------------------------------
* Environment handler
* only the first 6k in EEPROM are available for user. Of that we use 256b
*/
-#define CONFIG_SOFT_I2C
+#define CONFIG_SOFT_I2C
#define CFG_ENV_IS_IN_EEPROM 1 /* turn on EEPROM env feature */
#define CFG_ENV_OFFSET 0x1000
-#define CFG_ENV_SIZE 0x0700
-#define CFG_I2C_EEPROM_ADDR 0x57
+#define CFG_ENV_SIZE 0x0700
+#define CFG_I2C_EEPROM_ADDR 0x57
#define CFG_FACT_OFFSET 0x1800
-#define CFG_FACT_SIZE 0x0800
-#define CFG_I2C_FACT_ADDR 0x57
-#define CFG_EEPROM_PAGE_WRITE_BITS 3
-#define CFG_I2C_EEPROM_ADDR_LEN 2
+#define CFG_FACT_SIZE 0x0800
+#define CFG_I2C_FACT_ADDR 0x57
+#define CFG_EEPROM_PAGE_WRITE_BITS 3
+#define CFG_I2C_EEPROM_ADDR_LEN 2
#define CFG_EEPROM_SIZE 0x2000
#define CFG_I2C_SPEED 100000
-#define CFG_I2C_SLAVE 0xFE
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 12
-#define CONFIG_ENV_OVERWRITE
-#define CONFIG_MISC_INIT_R
-
-#if defined (CONFIG_SOFT_I2C)
-#define SDA 0x00010
-#define SCL 0x00020
-#define DIR immr->im_cpm.cp_pbdir
-#define DAT immr->im_cpm.cp_pbdat
-#define PAR immr->im_cpm.cp_pbpar
-#define ODR immr->im_cpm.cp_pbodr
-#define I2C_INIT {PAR&=~(SDA|SCL);ODR&=~(SDA|SCL);DAT|=(SDA|SCL);DIR|=(SDA|SCL);}
-#define I2C_READ ((DAT&SDA)?1:0)
-#define I2C_SDA(x) {if(x)DAT|=SDA;else DAT&=~SDA;}
-#define I2C_SCL(x) {if(x)DAT|=SCL;else DAT&=~SCL;}
-#define I2C_DELAY {udelay(5);}
-#define I2C_ACTIVE {DIR|=SDA;}
-#define I2C_TRISTATE {DIR&=~SDA;}
+#define CFG_I2C_SLAVE 0xFE
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 12
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_MISC_INIT_R
+
+#if defined (CONFIG_SOFT_I2C)
+#define SDA 0x00010
+#define SCL 0x00020
+#define DIR immr->im_cpm.cp_pbdir
+#define DAT immr->im_cpm.cp_pbdat
+#define PAR immr->im_cpm.cp_pbpar
+#define ODR immr->im_cpm.cp_pbodr
+#define I2C_INIT {PAR&=~(SDA|SCL);ODR&=~(SDA|SCL);DAT|=(SDA|SCL);DIR|=(SDA|SCL);}
+#define I2C_READ ((DAT&SDA)?1:0)
+#define I2C_SDA(x) {if(x)DAT|=SDA;else DAT&=~SDA;}
+#define I2C_SCL(x) {if(x)DAT|=SCL;else DAT&=~SCL;}
+#define I2C_DELAY {udelay(5);}
+#define I2C_ACTIVE {DIR|=SDA;}
+#define I2C_TRISTATE {DIR&=~SDA;}
#endif
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
/*-----------------------------------------------------------------------
* defines we need to get FEC running
- */
+ */
#define CONFIG_NET_MULTI 1 /* the only way to get the FEC in */
#define CONFIG_FEC_ENET 1 /* Ethernet only via FEC */
-#define FEC_ENET 1 /* eth.c needs it that way... */
+#define FEC_ENET 1 /* eth.c needs it that way... */
#define CFG_DISCOVER_PHY 1
#define CONFIG_MII 1
#define CONFIG_PHY_ADDR 31
-
+
/*-----------------------------------------------------------------------
* adresses
- */
+ */
#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
#define CFG_MONITOR_BASE TEXT_BASE
#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
+
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
@@ -220,7 +220,7 @@
*/
#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE 0x80000000
-
+
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
@@ -262,36 +262,36 @@
/*-----------------------------------------------------------------------
* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
*-----------------------------------------------------------------------
- * set up PLPRCR (PLL, Low-Power, and Reset Control Register)
- * 12 MF calculated Multiplication factor
- * 4 0 0000
- * 1 SPLSS 0 System PLL lock status sticky
- * 1 TEXPS 1 Timer expired status
- * 1 0 0
- * 1 TMIST 0 Timers interrupt status
- * 1 0 0
- * 1 CSRC 0 Clock source (0=DFNH, 1=DFNL)
- * 2 LPM 00 Low-power modes
- * 1 CSR 0 Checkstop reset enable
- * 1 LOLRE 0 Loss-of-lock reset enable
- * 1 FIOPD 0 Force I/O pull down
- * 5 0 00000
+ * set up PLPRCR (PLL, Low-Power, and Reset Control Register)
+ * 12 MF calculated Multiplication factor
+ * 4 0 0000
+ * 1 SPLSS 0 System PLL lock status sticky
+ * 1 TEXPS 1 Timer expired status
+ * 1 0 0
+ * 1 TMIST 0 Timers interrupt status
+ * 1 0 0
+ * 1 CSRC 0 Clock source (0=DFNH, 1=DFNL)
+ * 2 LPM 00 Low-power modes
+ * 1 CSR 0 Checkstop reset enable
+ * 1 LOLRE 0 Loss-of-lock reset enable
+ * 1 FIOPD 0 Force I/O pull down
+ * 5 0 00000
*/
#define CFG_PLPRCR (PLPRCR_TEXPS | ((CFG_MF-1)<<20))
-
+
/*-----------------------------------------------------------------------
* SYPCR - System Protection Control 11-9
* SYPCR can only be written once after reset!
*-----------------------------------------------------------------------
- * set up SYPCR:
- * 16 SWTC 0xffff Software watchdog timer count
- * 8 BMT 0xff Bus monitor timing
- * 1 BME 1 Bus monitor enable
- * 3 0 000
- * 1 SWF 1 Software watchdog freeze
- * 1 SWE 0/1 Software watchdog enable
- * 1 SWRI 0/1 Software watchdog reset/interrupt select (1=HRESET)
- * 1 SWP 0/1 Software watchdog prescale (1=/2048)
+ * set up SYPCR:
+ * 16 SWTC 0xffff Software watchdog timer count
+ * 8 BMT 0xff Bus monitor timing
+ * 1 BME 1 Bus monitor enable
+ * 3 0 000
+ * 1 SWF 1 Software watchdog freeze
+ * 1 SWE 0/1 Software watchdog enable
+ * 1 SWRI 0/1 Software watchdog reset/interrupt select (1=HRESET)
+ * 1 SWP 0/1 Software watchdog prescale (1=/2048)
*/
#if defined (CONFIG_WATCHDOG)
#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
@@ -303,31 +303,31 @@
/*-----------------------------------------------------------------------
* SIUMCR - SIU Module Configuration 11-6
*-----------------------------------------------------------------------
- * set up SIUMCR
- * 1 EARB 0 External arbitration
- * 3 EARP 000 External arbitration request priority
- * 4 0 0000
- * 1 DSHW 0 Data show cycles
- * 2 DBGC 00 Debug pin configuration
- * 2 DBPC 00 Debug port pins configuration
- * 1 0 0
- * 1 FRC 0 FRZ pin configuration
- * 1 DLK 0 Debug register lock
- * 1 OPAR 0 Odd parity
- * 1 PNCS 0 Parity enable for non memory controller regions
- * 1 DPC 0 Data parity pins configuration
- * 1 MPRE 0 Multiprocessor reservation enable
- * 2 MLRC 11 Multi level reservation control (00=IRQ4, 01=3State, 10=KR/RETRY, 11=SPKROUT)
- * 1 AEME 0 Async external master enable
- * 1 SEME 0 Sync external master enable
- * 1 BSC 0 Byte strobe configuration
- * 1 GB5E 0 GPL_B5 enable
- * 1 B2DD 0 Bank 2 double drive
- * 1 B3DD 0 Bank 3 double drive
- * 4 0 0000
+ * set up SIUMCR
+ * 1 EARB 0 External arbitration
+ * 3 EARP 000 External arbitration request priority
+ * 4 0 0000
+ * 1 DSHW 0 Data show cycles
+ * 2 DBGC 00 Debug pin configuration
+ * 2 DBPC 00 Debug port pins configuration
+ * 1 0 0
+ * 1 FRC 0 FRZ pin configuration
+ * 1 DLK 0 Debug register lock
+ * 1 OPAR 0 Odd parity
+ * 1 PNCS 0 Parity enable for non memory controller regions
+ * 1 DPC 0 Data parity pins configuration
+ * 1 MPRE 0 Multiprocessor reservation enable
+ * 2 MLRC 11 Multi level reservation control (00=IRQ4, 01=3State, 10=KR/RETRY, 11=SPKROUT)
+ * 1 AEME 0 Async external master enable
+ * 1 SEME 0 Sync external master enable
+ * 1 BSC 0 Byte strobe configuration
+ * 1 GB5E 0 GPL_B5 enable
+ * 1 B2DD 0 Bank 2 double drive
+ * 1 B3DD 0 Bank 3 double drive
+ * 4 0 0000
*/
#define CFG_SIUMCR (SIUMCR_MLRC11)
-
+
/*-----------------------------------------------------------------------
* TBSCR - Time Base Status and Control 11-26
*-----------------------------------------------------------------------
@@ -345,30 +345,30 @@
/*-----------------------------------------------------------------------
* SCCR - System Clock and reset Control Register 15-27
*-----------------------------------------------------------------------
- * set up SCCR (System Clock and Reset Control Register)
- * 1 0 0
- * 2 COM 11 Clock output module (00=full, 01=half, 11=off)
- * 3 0 000
- * 1 TBS 1 Timebase source (0=OSCCLK, 1=GCLK2)
- * 1 RTDIV 0 Real-time clock divide (0=/4, 1=/512)
- * 1 RTSEL 0 Real-time clock select (0=OSCM, 1=EXTCLK)
- * 1 CRQEN 0 CPM request enable
- * 1 PRQEN 0 Power management request enable
- * 2 0 00
- * 2 EBDF xx External bus division factor
- * 2 0 00
- * 2 DFSYNC 00 Division factor for SYNCLK
- * 2 DFBRG 00 Division factor for BRGCLK
- * 3 DFNL 000 Division factor low frequency
- * 3 DFNH 000 Division factor high frequency
- * 5 0 00000
+ * set up SCCR (System Clock and Reset Control Register)
+ * 1 0 0
+ * 2 COM 11 Clock output module (00=full, 01=half, 11=off)
+ * 3 0 000
+ * 1 TBS 1 Timebase source (0=OSCCLK, 1=GCLK2)
+ * 1 RTDIV 0 Real-time clock divide (0=/4, 1=/512)
+ * 1 RTSEL 0 Real-time clock select (0=OSCM, 1=EXTCLK)
+ * 1 CRQEN 0 CPM request enable
+ * 1 PRQEN 0 Power management request enable
+ * 2 0 00
+ * 2 EBDF xx External bus division factor
+ * 2 0 00
+ * 2 DFSYNC 00 Division factor for SYNCLK
+ * 2 DFBRG 00 Division factor for BRGCLK
+ * 3 DFNL 000 Division factor low frequency
+ * 3 DFNH 000 Division factor high frequency
+ * 5 0 00000
*/
#define SCCR_MASK 0
-#if CONFIG_EBDF
+#if CONFIG_EBDF
#define CFG_SCCR (SCCR_COM11 | SCCR_TBS | SCCR_EBDF01)
-#else
+#else
#define CFG_SCCR (SCCR_COM11 | SCCR_TBS)
-#endif
+#endif
/*-----------------------------------------------------------------------
* Chip Select 0 - FLASH
@@ -379,7 +379,7 @@
#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_4_CLK | OR_TRLX | OR_EHTR)
#define CFG_OR0_PRELIM (-CFG_FLASH_MAX | CFG_OR_TIMING_FLASH)
#define CFG_BR0_PRELIM (CFG_FLASH_BASE | BR_PS_16 | BR_V )
-
+
/*-----------------------------------------------------------------------
* misc
*-----------------------------------------------------------------------
@@ -408,11 +408,11 @@
/*
* BOOTP options
*/
-#undef CONFIG_BOOTP_MASK
+#undef CONFIG_BOOTP_MASK
#define CONFIG_BOOTP_MASK ( CONFIG_BOOTP_DEFAULT | \
CONFIG_BOOTP_BOOTFILESIZE \
- )
-
+ )
+
/*
* Set default IP stuff just to get bootstrap entries into the
@@ -421,13 +421,13 @@
#define CONFIG_ETHADDR 9a:52:63:15:85:25
#define CONFIG_SERVERIP 10.0.4.200
#define CONFIG_IPADDR 10.0.4.111
-
+
/*-----------------------------------------------------------------------
* Defaults for Autoscript
*/
#define CFG_LOAD_ADDR 0x00100000 /* default load address */
#define CFG_TFTP_LOADADDR 0x00100000
-
+
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
@@ -435,5 +435,5 @@
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
+
#endif /* __CONFIG_H */