summaryrefslogtreecommitdiff
path: root/include/configs/canyonlands.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs/canyonlands.h')
-rw-r--r--include/configs/canyonlands.h89
1 files changed, 81 insertions, 8 deletions
diff --git a/include/configs/canyonlands.h b/include/configs/canyonlands.h
index e244c87..b1b4709 100644
--- a/include/configs/canyonlands.h
+++ b/include/configs/canyonlands.h
@@ -114,6 +114,65 @@
#else
#define CFG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */
#define CFG_NAND_CS 0 /* NAND chip connected to CSx */
+#define CFG_ENV_IS_EMBEDDED 1 /* use embedded environment */
+#endif
+
+/*
+ * IPL (Initial Program Loader, integrated inside CPU)
+ * Will load first 4k from NAND (SPL) into cache and execute it from there.
+ *
+ * SPL (Secondary Program Loader)
+ * Will load special U-Boot version (NUB) from NAND and execute it. This SPL
+ * has to fit into 4kByte. It sets up the CPU and configures the SDRAM
+ * controller and the NAND controller so that the special U-Boot image can be
+ * loaded from NAND to SDRAM.
+ *
+ * NUB (NAND U-Boot)
+ * This NAND U-Boot (NUB) is a special U-Boot version which can be started
+ * from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
+ *
+ * On 440EPx the SPL is copied to SDRAM before the NAND controller is
+ * set up. While still running from cache, I experienced problems accessing
+ * the NAND controller. sr - 2006-08-25
+ */
+#define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */
+#define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */
+#define CFG_NAND_BOOT_SPL_DST (CFG_OCM_BASE + (12 << 10)) /* Copy SPL here */
+#define CFG_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */
+#define CFG_NAND_U_BOOT_START CFG_NAND_U_BOOT_DST /* Start NUB from */
+ /* this addr */
+#define CFG_NAND_BOOT_SPL_DELTA (CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)
+
+/*
+ * Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
+ */
+#define CFG_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */
+#define CFG_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */
+
+/*
+ * Now the NAND chip has to be defined (no autodetection used!)
+ */
+#define CFG_NAND_PAGE_SIZE 512 /* NAND chip page size */
+#define CFG_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */
+#define CFG_NAND_PAGE_COUNT 32 /* NAND chip page count */
+#define CFG_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */
+#undef CFG_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */
+
+#define CFG_NAND_ECCSIZE 256
+#define CFG_NAND_ECCBYTES 3
+#define CFG_NAND_ECCSTEPS (CFG_NAND_PAGE_SIZE / CFG_NAND_ECCSIZE)
+#define CFG_NAND_OOBSIZE 16
+#define CFG_NAND_ECCTOTAL (CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS)
+#define CFG_NAND_ECCPOS {0, 1, 2, 3, 6, 7}
+
+#ifdef CFG_ENV_IS_IN_NAND
+/*
+ * For NAND booting the environment is embedded in the U-Boot image. Please take
+ * look at the file board/amcc/canyonlands/u-boot-nand.lds for details.
+ */
+#define CFG_ENV_SIZE CFG_NAND_BLOCK_SIZE
+#define CFG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CFG_ENV_SIZE)
+#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET + CFG_ENV_SIZE)
#endif
/*-----------------------------------------------------------------------
@@ -154,10 +213,18 @@
/*------------------------------------------------------------------------------
* DDR SDRAM
*----------------------------------------------------------------------------*/
+#if !defined(CONFIG_NAND_U_BOOT)
+/*
+ * NAND booting U-Boot version uses a fixed initialization, since the whole
+ * I2C SPD DIMM autodetection/calibration doesn't fit into the 4k of boot
+ * code.
+ */
#define CONFIG_SPD_EEPROM 1 /* Use SPD EEPROM for setup */
#define SPD_EEPROM_ADDRESS {0x50, 0x51} /* SPD i2c spd addresses*/
#define CONFIG_DDR_ECC 1 /* with ECC support */
#define CONFIG_DDR_RQDC_FIXED 0x80000038 /* fixed value for RQDC */
+#endif
+#define CFG_MBYTES_SDRAM 256 /* 256MB */
/*-----------------------------------------------------------------------
* I2C
@@ -367,23 +434,29 @@
* EBC address which accepts bigger regions:
*
* 0xfc00.0000 -> 4.cc00.0000
- *
- * For this we have to remap the CS0 and re-relocate the envrironment,
- * since the original FLASH location which was needed upon startup is
- * now not correct anymore.
*/
+#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
+/* Memory Bank 3 (NOR-FLASH) initialization */
+#define CFG_EBC_PB3AP 0x10055e00
+#define CFG_EBC_PB3CR (CFG_BOOT_BASE_ADDR | 0x9a000)
+
+/* Memory Bank 0 (NAND-FLASH) initialization */
+#define CFG_EBC_PB0AP 0x018003c0
+#define CFG_EBC_PB0CR (CFG_NAND_ADDR | 0x1E000) /* BAS=NAND,BS=1MB,BU=R/W,BW=32bit*/
+#else
/* Memory Bank 0 (NOR-FLASH) initialization */
#define CFG_EBC_PB0AP 0x10055e00
#define CFG_EBC_PB0CR (CFG_BOOT_BASE_ADDR | 0x9a000)
-/* Memory Bank 2 (CPLD) initialization */
-#define CFG_EBC_PB2AP 0x00804240
-#define CFG_EBC_PB2CR (CFG_BCSR_BASE | 0x18000) /* BAS=CPLD,BS=1M,BU=RW,BW=32bit */
-
/* Memory Bank 3 (NAND-FLASH) initialization */
#define CFG_EBC_PB3AP 0x018003c0
#define CFG_EBC_PB3CR (CFG_NAND_ADDR | 0x1E000) /* BAS=NAND,BS=1MB,BU=R/W,BW=32bit*/
+#endif
+
+/* Memory Bank 2 (CPLD) initialization */
+#define CFG_EBC_PB2AP 0x00804240
+#define CFG_EBC_PB2CR (CFG_BCSR_BASE | 0x18000) /* BAS=CPLD,BS=1M,BU=RW,BW=32bit */
#define CFG_EBC_CFG 0xB8400000 /* EBC0_CFG */