diff options
Diffstat (limited to 'include/configs/cm5200.h')
| -rw-r--r-- | include/configs/cm5200.h | 286 |
1 files changed, 0 insertions, 286 deletions
diff --git a/include/configs/cm5200.h b/include/configs/cm5200.h deleted file mode 100644 index 3777a0d..0000000 --- a/include/configs/cm5200.h +++ /dev/null @@ -1,286 +0,0 @@ -/* - * (C) Copyright 2003-2007 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ -#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */ -#define CONFIG_CM5200 1 /* ... on CM5200 platform */ - -#define CONFIG_SYS_TEXT_BASE 0xfc000000 - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ - -/* - * Supported commands - */ -#define CONFIG_CMD_REGINFO - -/* - * Serial console configuration - */ -#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -/* - * Ethernet configuration - */ -#define CONFIG_MPC5xxx_FEC 1 -#define CONFIG_MPC5xxx_FEC_MII100 -#define CONFIG_PHY_ADDR 0x00 -#define CONFIG_ENV_OVERWRITE 1 /* allow overwriting of ethaddr */ -/* use misc_init_r() to read ethaddr from I2C EEPROM (see CONFIG_SYS_I2C_EEPROM) */ -#define CONFIG_MISC_INIT_R 1 -#define CONFIG_MAC_OFFSET 0x35 /* MAC address offset in I2C EEPROM */ - -/* - * POST support - */ -#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | CONFIG_SYS_POST_CPU) -#define MPC5XXX_SRAM_POST_SIZE (MPC5XXX_SRAM_SIZE - 4) -/* List of I2C addresses to be verified by POST */ -#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_SLAVE, \ - CONFIG_SYS_I2C_IO, \ - CONFIG_SYS_I2C_EEPROM} - -/* display image timestamps */ -#define CONFIG_TIMESTAMP 1 - -/* - * Autobooting - */ -#define CONFIG_PREBOOT "echo;" \ - "echo Type \"run net_nfs_fdt\" to mount root filesystem over NFS;" \ - "echo" -#undef CONFIG_BOOTARGS - -/* - * Default environment settings - */ -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "netmask=255.255.0.0\0" \ - "ipaddr=192.168.160.33\0" \ - "serverip=192.168.1.1\0" \ - "gatewayip=192.168.1.1\0" \ - "console=ttyPSC0\0" \ - "u-boot_addr=100000\0" \ - "kernel_addr=200000\0" \ - "kernel_addr_flash=fc0c0000\0" \ - "fdt_addr=400000\0" \ - "fdt_addr_flash=fc0a0000\0" \ - "ramdisk_addr=500000\0" \ - "rootpath=/opt/eldk-4.1/ppc_6xx\0" \ - "u-boot=/tftpboot/cm5200/u-boot.bin\0" \ - "bootfile_fdt=/tftpboot/cm5200/uImage\0" \ - "fdt_file=/tftpboot/cm5200/cm5200.dtb\0" \ - "load=tftp ${u-boot_addr} ${u-boot}\0" \ - "update=prot off fc000000 +${filesize}; " \ - "era fc000000 +${filesize}; " \ - "cp.b ${u-boot_addr} fc000000 ${filesize}; " \ - "prot on fc000000 +${filesize}\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "flashargs=setenv bootargs root=/dev/mtdblock5 rw\0" \ - "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ - "addinit=setenv bootargs ${bootargs} init=/linuxrc\0" \ - "addcons=setenv bootargs ${bootargs} " \ - "console=${console},${baudrate}\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:" \ - "${netmask}:${hostname}:${netdev}:off panic=1\0" \ - "flash_flash=run flashargs addinit addip addcons;" \ - "bootm ${kernel_addr_flash} - ${fdt_addr_flash}\0" \ - "net_nfs_fdt=tftp ${kernel_addr} ${bootfile_fdt}; " \ - "tftp ${fdt_addr} ${fdt_file}; run nfsargs addip " \ - "addcons; bootm ${kernel_addr} - ${fdt_addr}\0" \ - "" -#define CONFIG_BOOTCOMMAND "run flash_flash" - -/* - * Low level configuration - */ - -/* - * Clock configuration - */ -#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* SYS_XTAL_IN = 33MHz */ -#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK 1 /* IPB = 133MHz */ - -/* - * Memory map - */ -#define CONFIG_SYS_MBAR 0xF0000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 - -#define CONFIG_SYS_LOWBOOT 1 - -/* Use ON-Chip SRAM until RAM will be available */ -#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM -#ifdef CONFIG_POST -/* preserve space for the post_word at end of on-chip SRAM */ -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE -#else -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE -#endif - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_BOARD_TYPES 1 /* we use board_type */ - -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* 384 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* 256 kB for malloc() */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* initial mem map for Linux */ - -/* - * Flash configuration - */ -#define CONFIG_SYS_FLASH_CFI 1 -#define CONFIG_FLASH_CFI_DRIVER 1 -#define CONFIG_SYS_FLASH_BASE 0xfc000000 -/* we need these despite using CFI */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max num of sectors on one chip */ -#define CONFIG_SYS_FLASH_SIZE 0x02000000 /* 32 MiB */ - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT 1 -#undef CONFIG_SYS_LOWBOOT -#endif - -/* - * Chip selects configuration - */ -/* Boot Chipselect */ -#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE -#define CONFIG_SYS_BOOTCS_CFG 0x00087D31 /* for pci_clk = 33 MHz */ -/* use board_early_init_r to enable flash write in CS_BOOT */ -#define CONFIG_BOARD_EARLY_INIT_R - -/* Flash memory addressing */ -#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE - -/* No burst, dead cycle = 1 for CS0 (Flash) */ -#define CONFIG_SYS_CS_BURST 0x00000000 -#define CONFIG_SYS_CS_DEADCYCLE 0x00000001 - -/* - * SDRAM configuration - * settings for k4s561632E-xx75, assuming XLB = 132 MHz - */ -#define SDRAM_MODE 0x00CD0000 /* CASL 3, burst length 8 */ -#define SDRAM_CONTROL 0x514F0000 -#define SDRAM_CONFIG1 0xE2333900 -#define SDRAM_CONFIG2 0x8EE70000 - -/* - * MTD configuration - */ -#define CONFIG_CMD_MTDPARTS 1 -#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ -#define CONFIG_FLASH_CFI_MTD -#define MTDIDS_DEFAULT "nor0=cm5200-0" -#define MTDPARTS_DEFAULT "mtdparts=cm5200-0:" \ - "384k(uboot),128k(env)," \ - "128k(redund_env),128k(dtb)," \ - "2m(kernel),27904k(rootfs)," \ - "-(config)" - -/* - * RTC configuration - */ -#define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */ - -/* - * USB configuration - */ -#define CONFIG_USB_OHCI 1 -#define CONFIG_USB_CLOCK 0x0001BBBB -#define CONFIG_USB_CONFIG 0x00001000 -/* Partitions (for USB) */ - -/* - * Invoke our last_stage_init function - needed by fwupdate - */ -#define CONFIG_LAST_STAGE_INIT 1 - -/* - * Environment settings - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x10000 -#define CONFIG_ENV_SECT_SIZE 0x20000 -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN) -/* Configuration of redundant environment */ -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -/* - * Pin multiplexing configuration - */ - -/* - * CS1/GPIO_WKUP_6: GPIO (default) - * ALTs: CAN1 on I2C1, CAN2 on TIMER0/1 - * IRDA/PSC6: UART - * Ether: Ethernet 100Mbit with MD - * PCI_DIS: PCI controller disabled - * USB: USB - * PSC3: SPI with UART3 - * PSC2: UART - * PSC1: UART - */ -#define CONFIG_SYS_GPS_PORT_CONFIG 0x10559C44 - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP 1 /* undef to save memory */ -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_ALT_MEMTEST 1 -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x03f00000 /* 1 .. 63 MiB in SDRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -/* - * Various low-level settings - */ -#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI -#define CONFIG_SYS_HID0_FINAL HID0_ICE - -#define CONFIG_SYS_XLB_PIPELINING 1 /* enable transaction pipeling */ - -/* - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ -#ifdef CONFIG_CMD_KGDB -#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/* - * Flat Device Tree support - */ -#define OF_CPU "PowerPC,5200@0" -#define OF_SOC "soc5200@f0000000" -#define OF_TBCLK (bd->bi_busfreq / 4) -#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000" - -#endif /* __CONFIG_H */ |