diff options
Diffstat (limited to 'include/configs')
-rw-r--r-- | include/configs/minnowmax.h | 2 | ||||
-rw-r--r-- | include/configs/sama5d2_ptc.h | 155 | ||||
-rw-r--r-- | include/configs/x86-common.h | 9 | ||||
-rw-r--r-- | include/configs/xilinx_zynqmp.h | 59 | ||||
-rw-r--r-- | include/configs/xilinx_zynqmp_zcu102.h | 6 | ||||
-rw-r--r-- | include/configs/zynq-common.h | 6 |
6 files changed, 227 insertions, 10 deletions
diff --git a/include/configs/minnowmax.h b/include/configs/minnowmax.h index 674d1f6..95ad128 100644 --- a/include/configs/minnowmax.h +++ b/include/configs/minnowmax.h @@ -40,6 +40,6 @@ #define CONFIG_X86EMU_RAW_IO #define CONFIG_ENV_SECT_SIZE 0x1000 -#define CONFIG_ENV_OFFSET 0x007fe000 +#define CONFIG_ENV_OFFSET 0x006ef000 #endif /* __CONFIG_H */ diff --git a/include/configs/sama5d2_ptc.h b/include/configs/sama5d2_ptc.h new file mode 100644 index 0000000..d91d75e --- /dev/null +++ b/include/configs/sama5d2_ptc.h @@ -0,0 +1,155 @@ +/* + * Configuration settings for the SAMA5D2 PTC Engineering board. + * + * Copyright (C) 2016 Atmel + * Wenyou Yang <wenyou.yang@atmel.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* No NOR flash, this definition should put before common header */ +#define CONFIG_SYS_NO_FLASH + +#include "at91-sama5_common.h" + +/* serial console */ +#define CONFIG_ATMEL_USART +#define CONFIG_USART_BASE ATMEL_BASE_UART0 +#define CONFIG_USART_ID ATMEL_ID_UART0 + +#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS +#define CONFIG_SYS_SDRAM_SIZE 0x20000000 + +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_INIT_SP_ADDR 0x210000 +#else +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE) +#endif + +#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */ + +#undef CONFIG_AT91_GPIO +#define CONFIG_ATMEL_PIO4 + +/* SDRAM */ +#define CONFIG_NR_DRAM_BANKS 1 + +/* SerialFlash */ +#ifdef CONFIG_CMD_SF +#define CONFIG_ATMEL_SPI +#define CONFIG_SPI_FLASH_ATMEL +#define CONFIG_SF_DEFAULT_BUS 0 +#define CONFIG_SF_DEFAULT_CS 0 +#define CONFIG_SF_DEFAULT_SPEED 30000000 +#endif + +/* NAND flash */ +#define CONFIG_CMD_NAND + +#ifdef CONFIG_CMD_NAND +#define CONFIG_NAND_ATMEL +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 +/* our ALE is AD21 */ +#define CONFIG_SYS_NAND_MASK_ALE (1 << 21) +/* our CLE is AD22 */ +#define CONFIG_SYS_NAND_MASK_CLE (1 << 22) +#define CONFIG_SYS_NAND_ONFI_DETECTION +/* PMECC & PMERRLOC */ +#define CONFIG_ATMEL_NAND_HWECC +#define CONFIG_ATMEL_NAND_HW_PMECC +#define CONFIG_CMD_NAND_TRIMFFS +#endif + +/* USB */ +#define CONFIG_CMD_USB + +#ifdef CONFIG_CMD_USB +#define CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_ATMEL +#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 +#define CONFIG_USB_STORAGE +#endif + +/* USB device */ +#define CONFIG_USB_GADGET +#define CONFIG_USB_GADGET_DUALSPEED +#define CONFIG_USB_GADGET_ATMEL_USBA +#define CONFIG_USB_ETHER +#define CONFIG_USB_ETH_RNDIS +#define CONFIG_USBNET_MANUFACTURER "Atmel SAMA5D2_PTC" + +#if defined(CONFIG_CMD_USB) +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif + +/* Ethernet Hardware */ +#define CONFIG_MACB +#define CONFIG_RMII +#define CONFIG_NET_RETRY_COUNT 20 +#define CONFIG_MACB_SEARCH_PHY + +#ifdef CONFIG_SYS_USE_NANDFLASH +#undef CONFIG_ENV_OFFSET +#undef CONFIG_ENV_OFFSET_REDUND +#undef CONFIG_BOOTCOMMAND +/* u-boot env in nand flash */ +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET 0x200000 +#define CONFIG_ENV_OFFSET_REDUND 0x400000 +#define CONFIG_BOOTCOMMAND "nand read 0x21000000 0xb80000 0x80000;" \ + "nand read 0x22000000 0x600000 0x600000;" \ + "bootz 0x22000000 - 0x21000000" +#endif + +#undef CONFIG_BOOTARGS +#define CONFIG_BOOTARGS \ + "console=ttyS0,57600 earlyprintk " \ + "mtdparts=atmel_nand:6M(bootstrap)ro, 6M(kernel)ro,-(rootfs) " \ + "rootfstype=ubifs ubi.mtd=2 root=ubi0:rootfs" + +/* SPL */ +#define CONFIG_SPL_FRAMEWORK +#define CONFIG_SPL_TEXT_BASE 0x200000 +#define CONFIG_SPL_MAX_SIZE 0x10000 +#define CONFIG_SPL_BSS_START_ADDR 0x20000000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 +#define CONFIG_SYS_SPL_MALLOC_START 0x20080000 +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000 + +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_GPIO_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT + +#define CONFIG_SPL_BOARD_INIT +#define CONFIG_SYS_MONITOR_LEN (512 << 10) + +#ifdef CONFIG_SYS_USE_SERIALFLASH +#define CONFIG_SPL_SPI_SUPPORT +#define CONFIG_SPL_SPI_FLASH_SUPPORT +#define CONFIG_SPL_SPI_LOAD +#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x8000 + +#elif CONFIG_SYS_USE_NANDFLASH +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_DRIVERS +#define CONFIG_SPL_NAND_BASE +#define CONFIG_PMECC_CAP 8 +#define CONFIG_PMECC_SECTOR_SIZE 512 +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000 +#define CONFIG_SYS_NAND_5_ADDR_CYCLE +#define CONFIG_SYS_NAND_PAGE_SIZE 0x1000 +#define CONFIG_SYS_NAND_PAGE_COUNT 64 +#define CONFIG_SYS_NAND_OOBSIZE 224 +#define CONFIG_SYS_NAND_BLOCK_SIZE 0x40000 +#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0 +#define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER +#endif + +#endif diff --git a/include/configs/x86-common.h b/include/configs/x86-common.h index b79f47b..b4aad6c 100644 --- a/include/configs/x86-common.h +++ b/include/configs/x86-common.h @@ -193,14 +193,19 @@ #define CONFIG_HOSTNAME x86 #define CONFIG_BOOTFILE "bzImage" #define CONFIG_LOADADDR 0x1000000 -#define CONFIG_RAMDISK_ADDR 0x4000000 +#define CONFIG_RAMDISK_ADDR 0x4000000 +#ifdef CONFIG_GENERATE_ACPI_TABLE +#define CONFIG_OTHBOOTARGS "othbootargs=\0" +#else +#define CONFIG_OTHBOOTARGS "othbootargs=acpi=off\0" +#endif #define CONFIG_EXTRA_ENV_SETTINGS \ CONFIG_STD_DEVICES_SETTINGS \ "pciconfighost=1\0" \ "netdev=eth0\0" \ "consoledev=ttyS0\0" \ - "othbootargs=acpi=off\0" \ + CONFIG_OTHBOOTARGS \ "ramdiskaddr=0x4000000\0" \ "ramdiskfile=initramfs.gz\0" diff --git a/include/configs/xilinx_zynqmp.h b/include/configs/xilinx_zynqmp.h index 6b8e3ea..b2fa164 100644 --- a/include/configs/xilinx_zynqmp.h +++ b/include/configs/xilinx_zynqmp.h @@ -41,7 +41,7 @@ # define CONFIG_IDENT_STRING " Xilinx ZynqMP" #endif -#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_INIT_SP_ADDR 0xfffffffc /* Generic Timer Definitions - setup in EL3. Setup by ATF for other cases */ #if !defined(COUNTER_FREQUENCY) @@ -65,6 +65,9 @@ #define CONFIG_CMD_ENV #define CONFIG_DOS_PARTITION #define CONFIG_EFI_PARTITION +#ifndef CONFIG_SPL_BUILD +# define CONFIG_ISO_PARTITION +#endif #define CONFIG_MP /* BOOTP options */ @@ -74,10 +77,24 @@ #define CONFIG_BOOTP_HOSTNAME #define CONFIG_BOOTP_MAY_FAIL #define CONFIG_BOOTP_SERVERIP +#define CONFIG_BOOTP_DNS +#define CONFIG_BOOTP_PXE +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_BOOTP_PXE_CLIENTARCH 0x100 + +/* Diff from config_distro_defaults.h */ +#define CONFIG_SUPPORT_RAW_INITRD +#define CONFIG_ENV_VARS_UBOOT_CONFIG +#define CONFIG_AUTO_COMPLETE + +/* PXE */ +#define CONFIG_CMD_PXE +#define CONFIG_MENU #if defined(CONFIG_ZYNQ_SDHCI) # define CONFIG_MMC # define CONFIG_GENERIC_MMC +# define CONFIG_SUPPORT_EMMC_BOOT # define CONFIG_SDHCI # ifndef CONFIG_ZYNQ_SDHCI_MAX_FREQ # define CONFIG_ZYNQ_SDHCI_MAX_FREQ 200000000 @@ -133,6 +150,7 @@ #endif /* Initial environment variables */ +#ifndef CONFIG_EXTRA_ENV_SETTINGS #define CONFIG_EXTRA_ENV_SETTINGS \ "kernel_addr=0x80000\0" \ "fdt_addr=0x7000000\0" \ @@ -143,8 +161,8 @@ "load mmc $sdbootdev:$partid $kernel_addr Image && " \ "booti $kernel_addr - $fdt_addr\0" \ DFU_ALT_INFO +#endif -#define CONFIG_PREBOOT "run bootargs" #define CONFIG_BOOTCOMMAND "run $modeboot" #define CONFIG_BOOTDELAY 3 @@ -212,4 +230,41 @@ #define CONFIG_BOARD_EARLY_INIT_R #define CONFIG_CLOCKS +#define CONFIG_SPL_TEXT_BASE 0xfffc0000 +#define CONFIG_SPL_MAX_SIZE 0x20000 + +/* Just random location in OCM */ +#define CONFIG_SPL_BSS_START_ADDR 0x1000000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x2000000 + +#define CONFIG_SPL_FRAMEWORK +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_BOARD_INIT +#define CONFIG_SPL_RAM_DEVICE + +#define CONFIG_SPL_OS_BOOT +/* u-boot is like dtb */ +#define CONFIG_SPL_FS_LOAD_ARGS_NAME "u-boot.bin" +#define CONFIG_SYS_SPL_ARGS_ADDR 0x8000000 + +/* ATF is my kernel image */ +#define CONFIG_SPL_FS_LOAD_KERNEL_NAME "atf.ub" + +/* FIT load address for RAM boot */ +#define CONFIG_SPL_LOAD_FIT_ADDRESS 0x10000000 + +/* MMC support */ +#ifdef CONFIG_ZYNQ_SDHCI +# define CONFIG_SPL_MMC_SUPPORT +# define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 +# define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0 /* unused */ +# define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0 /* unused */ +# define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0 /* unused */ +# define CONFIG_SPL_LIBDISK_SUPPORT +# define CONFIG_SPL_FAT_SUPPORT +# define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" +#endif + #endif /* __XILINX_ZYNQMP_H */ diff --git a/include/configs/xilinx_zynqmp_zcu102.h b/include/configs/xilinx_zynqmp_zcu102.h index 30db2e4..81079fe 100644 --- a/include/configs/xilinx_zynqmp_zcu102.h +++ b/include/configs/xilinx_zynqmp_zcu102.h @@ -48,6 +48,12 @@ #define CONFIG_IDENT_STRING " Xilinx ZynqMP ZCU102" +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_CMD_EEPROM +#define CONFIG_ZYNQ_EEPROM_BUS 5 +#define CONFIG_ZYNQ_GEM_EEPROM_ADDR 0x54 +#define CONFIG_ZYNQ_GEM_I2C_MAC_OFFSET 0x20 + #define CONFIG_KERNEL_FDT_OFST_SIZE \ "kernel_offset=0x180000\0" \ "fdt_offset=0x100000\0" \ diff --git a/include/configs/zynq-common.h b/include/configs/zynq-common.h index a3e4aec..82ece0d 100644 --- a/include/configs/zynq-common.h +++ b/include/configs/zynq-common.h @@ -315,11 +315,7 @@ #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 #define CONFIG_SPL_LIBDISK_SUPPORT #define CONFIG_SPL_FAT_SUPPORT -#ifdef CONFIG_OF_SEPARATE -# define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot-dtb.img" -#else -# define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" -#endif +#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" #endif /* Disable dcache for SPL just for sure */ |