diff options
Diffstat (limited to 'include/configs')
| -rw-r--r-- | include/configs/lsxl.h | 4 | ||||
| -rw-r--r-- | include/configs/ph1_ld4.h | 59 | ||||
| -rw-r--r-- | include/configs/ph1_pro4.h | 61 | ||||
| -rw-r--r-- | include/configs/ph1_sld8.h | 61 | ||||
| -rw-r--r-- | include/configs/sheevaplug.h | 46 | ||||
| -rw-r--r-- | include/configs/uniphier-common.h | 266 |
6 files changed, 491 insertions, 6 deletions
diff --git a/include/configs/lsxl.h b/include/configs/lsxl.h index bf5c1a1..a14bfe3 100644 --- a/include/configs/lsxl.h +++ b/include/configs/lsxl.h @@ -8,6 +8,8 @@ #ifndef _CONFIG_LSXL_H #define _CONFIG_LSXL_H +#define CONFIG_SYS_GENERIC_BOARD + /* * Version number information */ @@ -157,7 +159,7 @@ "standard_env=setenv ipaddr; setenv netmask; setenv serverip; " \ "setenv ncip; setenv gatewayip; setenv ethact; " \ "setenv bootfile; setenv dnsip; " \ - "setenv bootsource hdd; run ser\0" \ + "setenv bootsource legacy; run ser\0" \ "restore_env=run standard_env; saveenv; reset\0" \ "ser=setenv stdin serial; setenv stdout serial; " \ "setenv stderr serial\0" \ diff --git a/include/configs/ph1_ld4.h b/include/configs/ph1_ld4.h new file mode 100644 index 0000000..a28d7b5 --- /dev/null +++ b/include/configs/ph1_ld4.h @@ -0,0 +1,59 @@ +/* + * Copyright (C) 2012-2014 Panasonic Corporation + * Author: Masahiro Yamada <yamada.m@jp.panasonic.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __PH1_XXX_H +#define __PH1_XXX_H + +/* + * Support Card Select + * + * CONFIG_PFC_MICRO_SUPPORT_CARD - Original Micro Support Card made by PFC. + * CONFIG_DCC_MICRO_SUPPORT_CARD - DCC version Micro Support Card. + * CPLD is re-programmed for ARIMA board compatibility. + * No define - No support card. + */ + +#if 0 +#define CONFIG_PFC_MICRO_SUPPORT_CARD +#else +#define CONFIG_DCC_MICRO_SUPPORT_CARD +#endif + +/* + * Serial Configuration + * SoC UART : enable CONFIG_UNIPHIER_SERIAL + * On-board UART: enable CONFIG_SYS_NS16550_SERIAL + */ +#if 1 +#define CONFIG_UNIPHIER_SERIAL +#else +#define CONFIG_SYS_NS16550_SERIAL +#endif + +#define CONFIG_SYS_UNIPHIER_UART_CLK 36864000 + +#define CONFIG_SMC911X + +#define CONFIG_DDR_NUM_CH0 1 +#define CONFIG_DDR_NUM_CH1 1 + +#define CONFIG_DDR_FREQ 1600 + +/* + * Memory Size & Mapping + */ +/* Physical start address of SDRAM */ +#define CONFIG_SDRAM0_BASE 0x80000000 +#define CONFIG_SDRAM0_SIZE 0x10000000 +#define CONFIG_SDRAM1_BASE 0x90000000 +#define CONFIG_SDRAM1_SIZE 0x10000000 + +#define CONFIG_SPL_TEXT_BASE 0x40000 + +#include "uniphier-common.h" + +#endif /* __PH1_XXX_H */ diff --git a/include/configs/ph1_pro4.h b/include/configs/ph1_pro4.h new file mode 100644 index 0000000..b79967f --- /dev/null +++ b/include/configs/ph1_pro4.h @@ -0,0 +1,61 @@ +/* + * Copyright (C) 2012-2014 Panasonic Corporation + * Author: Masahiro Yamada <yamada.m@jp.panasonic.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __PH1_XXX_H +#define __PH1_XXX_H + +/* + * Support Card Select + * + * CONFIG_PFC_MICRO_SUPPORT_CARD - Original Micro Support Card made by PFC. + * CONFIG_DCC_MICRO_SUPPORT_CARD - DCC version Micro Support Card. + * CPLD is re-programmed for ARIMA board compatibility. + * No define - No support card. + */ + +#if 0 +#define CONFIG_PFC_MICRO_SUPPORT_CARD +#else +#define CONFIG_DCC_MICRO_SUPPORT_CARD +#endif + +/* + * Serial Configuration + * SoC UART : enable CONFIG_UNIPHIER_SERIAL + * On-board UART: enable CONFIG_SYS_NS16550_SERIAL + */ +#if 1 +#define CONFIG_UNIPHIER_SERIAL +#else +#define CONFIG_SYS_NS16550_SERIAL +#endif + +#define CONFIG_SYS_UNIPHIER_UART_CLK 73728000 + +#define CONFIG_SMC911X + +#define CONFIG_DDR_NUM_CH0 2 +#define CONFIG_DDR_NUM_CH1 2 + +#define CONFIG_DDR_FREQ 1600 + +#define CONFIG_UNIPHIER_SMP + +/* + * Memory Size & Mapping + */ +/* Physical start address of SDRAM */ +#define CONFIG_SDRAM0_BASE 0x80000000 +#define CONFIG_SDRAM0_SIZE 0x20000000 +#define CONFIG_SDRAM1_BASE 0xa0000000 +#define CONFIG_SDRAM1_SIZE 0x20000000 + +#define CONFIG_SPL_TEXT_BASE 0x100000 + +#include "uniphier-common.h" + +#endif /* __PH1_XXX_H */ diff --git a/include/configs/ph1_sld8.h b/include/configs/ph1_sld8.h new file mode 100644 index 0000000..9d391f1 --- /dev/null +++ b/include/configs/ph1_sld8.h @@ -0,0 +1,61 @@ +/* + * Copyright (C) 2012-2014 Panasonic Corporation + * Author: Masahiro Yamada <yamada.m@jp.panasonic.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __PH1_XXX_H +#define __PH1_XXX_H + +/* + * Support Card Select + * + * CONFIG_PFC_MICRO_SUPPORT_CARD - Original Micro Support Card made by PFC. + * CONFIG_DCC_MICRO_SUPPORT_CARD - DCC version Micro Support Card. + * CPLD is re-programmed for ARIMA board compatibility. + * No define - No support card. + */ + +#if 0 +#define CONFIG_PFC_MICRO_SUPPORT_CARD +#else +#define CONFIG_DCC_MICRO_SUPPORT_CARD +#endif + +/* + * Serial Configuration + * SoC UART : enable CONFIG_UNIPHIER_SERIAL + * On-board UART: enable CONFIG_SYS_NS16550_SERIAL + */ +#if 1 +#define CONFIG_UNIPHIER_SERIAL +#else +#define CONFIG_SYS_NS16550_SERIAL +#endif + +#define CONFIG_SYS_UNIPHIER_UART_CLK 80000000 + +#define CONFIG_SMC911X + +#define CONFIG_DDR_NUM_CH0 1 +#define CONFIG_DDR_NUM_CH1 1 + +#define CONFIG_DDR_FREQ 1333 + +/* #define CONFIG_DDR_STANDARD */ + +/* + * Memory Size & Mapping + */ +/* Physical start address of SDRAM */ +#define CONFIG_SDRAM0_BASE 0x80000000 +#define CONFIG_SDRAM0_SIZE 0x10000000 +#define CONFIG_SDRAM1_BASE 0x90000000 +#define CONFIG_SDRAM1_SIZE 0x10000000 + +#define CONFIG_SPL_TEXT_BASE 0x40000 + +#include "uniphier-common.h" + +#endif /* __PH1_XXX_H */ diff --git a/include/configs/sheevaplug.h b/include/configs/sheevaplug.h index 4747adf..71be823 100644 --- a/include/configs/sheevaplug.h +++ b/include/configs/sheevaplug.h @@ -1,5 +1,6 @@ /* - * (C) Copyright 2009 + * (C) Copyright 2009-2014 + * Gerald Kerma <dreagle@doukki.net> * Marvell Semiconductor <www.marvell.com> * Written-by: Prafulla Wadaskar <prafulla@marvell.com> * @@ -23,12 +24,26 @@ #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ /* + * Compression configuration + */ +#define CONFIG_BZIP2 +#define CONFIG_LZMA +#define CONFIG_LZO + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ + +/* * Commands configuration */ #define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ #include <config_cmd_default.h> +#define CONFIG_CMD_BOOTZ #define CONFIG_CMD_DHCP #define CONFIG_CMD_ENV +#define CONFIG_CMD_IDE #define CONFIG_CMD_MII #define CONFIG_CMD_MMC #define CONFIG_CMD_NAND @@ -54,8 +69,8 @@ * it has to be rounded to sector size */ #define CONFIG_ENV_SIZE 0x20000 /* 128k */ -#define CONFIG_ENV_ADDR 0x60000 -#define CONFIG_ENV_OFFSET 0x60000 /* env starts here */ +#define CONFIG_ENV_ADDR 0x80000 +#define CONFIG_ENV_OFFSET 0x80000 /* env starts here */ /* * Default environment variables @@ -64,8 +79,10 @@ "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \ "${x_bootcmd_usb}; bootm 0x6400000;" -#define CONFIG_MTDPARTS "orion_nand:512k(uboot)," \ - "3m@1m(kernel),1m@4m(psm),13m@5m(rootfs) rw\0" +#define CONFIG_MTDPARTS \ + "mtdparts=orion_nand:512K(uboot)," \ + "512K(env),1M(script),6M(kernel)," \ + "12M(ramdisk),4M(spare),-(rootfs)" #define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console" \ "=ttyS0,115200 mtdparts="CONFIG_MTDPARTS \ @@ -73,6 +90,11 @@ "x_bootcmd_usb=usb start\0" \ "x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2\0" +#define MTDIDS_DEFAULT "nand0=orion_nand" + +#define MTDPARTS_DEFAULT \ + "mtdparts="CONFIG_MTDPARTS + /* * Ethernet Driver configuration */ @@ -92,9 +114,23 @@ #endif /* CONFIG_CMD_MMC */ /* + * SATA driver configuration + */ +#ifdef CONFIG_CMD_IDE +#define __io +#define CONFIG_IDE_PREINIT +#define CONFIG_DOS_PARTITION +#define CONFIG_MVSATA_IDE_USE_PORT0 +#define CONFIG_MVSATA_IDE_USE_PORT1 +#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET +#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET +#endif /* CONFIG_CMD_IDE */ + +/* * File system */ #define CONFIG_CMD_EXT2 +#define CONFIG_CMD_EXT4 #define CONFIG_CMD_FAT #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_UBI diff --git a/include/configs/uniphier-common.h b/include/configs/uniphier-common.h new file mode 100644 index 0000000..18fe277 --- /dev/null +++ b/include/configs/uniphier-common.h @@ -0,0 +1,266 @@ +/* + * Copyright (C) 2012-2014 Panasonic Corporation + * Author: Masahiro Yamada <yamada.m@jp.panasonic.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* U-boot - Common settings for UniPhier Family */ + +#ifndef __CONFIG_UNIPHIER_COMMON_H__ +#define __CONFIG_UNIPHIER_COMMON_H__ + +#if defined(CONFIG_PFC_MICRO_SUPPORT_CARD) && \ + defined(CONFIG_DCC_MICRO_SUPPORT_CARD) +# error "Both CONFIG_PFC_MICRO_SUPPORT_CARD and CONFIG_DCC_MICRO_SUPPORT_CARD \ +are defined. Select only one of them." +#endif + +/* + * Support card address map + */ +#if defined(CONFIG_PFC_MICRO_SUPPORT_CARD) +# define CONFIG_SUPPORT_CARD_BASE 0x03f00000 +# define CONFIG_SUPPORT_CARD_ETHER_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00000000) +# define CONFIG_SUPPORT_CARD_LED_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00090000) +# define CONFIG_SUPPORT_CARD_UART_BASE (CONFIG_SUPPORT_CARD_BASE + 0x000b0000) +#endif + +#if defined(CONFIG_DCC_MICRO_SUPPORT_CARD) +# define CONFIG_SUPPORT_CARD_BASE 0x08000000 +# define CONFIG_SUPPORT_CARD_ETHER_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00000000) +# define CONFIG_SUPPORT_CARD_LED_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00401630) +# define CONFIG_SUPPORT_CARD_UART_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00200000) +#endif + +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_COM1 CONFIG_SUPPORT_CARD_UART_BASE +#define CONFIG_SYS_NS16550_CLK 12288000 +#define CONFIG_SYS_NS16550_REG_SIZE -2 + +#define CONFIG_SMC911X_BASE CONFIG_SUPPORT_CARD_ETHER_BASE +#define CONFIG_SMC911X_32_BIT + +#define CONFIG_SYS_UNIPHIER_SERIAL_BASE0 0x54006800 +#define CONFIG_SYS_UNIPHIER_SERIAL_BASE1 0x54006900 +#define CONFIG_SYS_UNIPHIER_SERIAL_BASE2 0x54006a00 +#define CONFIG_SYS_UNIPHIER_SERIAL_BASE3 0x54006b00 + +/*----------------------------------------------------------------------- + * MMU and Cache Setting + *----------------------------------------------------------------------*/ + +/* Comment out the following to enable L1 cache */ +/* #define CONFIG_SYS_ICACHE_OFF */ +/* #define CONFIG_SYS_DCACHE_OFF */ + +/* Comment out the following to enable L2 cache */ +#define CONFIG_UNIPHIER_L2CACHE_ON + +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DISPLAY_BOARDINFO +#define CONFIG_BOARD_LATE_INIT + +#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) + +#define CONFIG_TIMESTAMP + +/* FLASH related */ +#define CONFIG_MTD_DEVICE + +/* + * uncomment the following to disable FLASH related code. + */ +/* #define CONFIG_SYS_NO_FLASH */ + +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI + +#define CONFIG_SYS_MAX_FLASH_SECT 256 +#define CONFIG_SYS_MONITOR_BASE 0 +#define CONFIG_SYS_FLASH_BASE 0 + +/* + * flash_toggle does not work for out supoort card. + * We need to use flash_status_poll. + */ +#define CONFIG_SYS_CFI_FLASH_STATUS_POLL + +#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ + +#if defined(CONFIG_PFC_MICRO_SUPPORT_CARD) +# define CONFIG_SYS_MAX_FLASH_BANKS 1 +# define CONFIG_SYS_FLASH_BANKS_LIST {0x00000000} +# define CONFIG_SYS_FLASH_BANKS_SIZES {0x02000000} +#endif + +#if defined(CONFIG_DCC_MICRO_SUPPORT_CARD) +# define CONFIG_SYS_MAX_FLASH_BANKS 1 +# define CONFIG_SYS_FLASH_BANKS_LIST {0x04000000} +# define CONFIG_SYS_FLASH_BANKS_SIZES {0x04000000} +#endif + +/* serial console configuration */ +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_SYS_GENERIC_BOARD + +#if !defined(CONFIG_SPL_BUILD) +#define CONFIG_USE_ARCH_MEMSET +#define CONFIG_USE_ARCH_MEMCPY +#endif + +#define CONFIG_SYS_LONGHELP /* undef to save memory */ + +#define CONFIG_CMDLINE_EDITING /* add command line history */ +#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command */ +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE) + +#define CONFIG_CONS_INDEX 1 + +/* + * For NAND booting the environment is embedded in the U-Boot image. Please take + * look at the file board/amcc/canyonlands/u-boot-nand.lds for details. + */ +/* #define CONFIG_ENV_IS_IN_NAND */ +#define CONFIG_ENV_IS_NOWHERE +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_OFFSET 0x0 +/* #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) */ + +/* Time clock 1MHz */ +#define CONFIG_SYS_TIMER_RATE 1000000 + +/* + * By default, ARP timeout is 5 sec. + * The first ARP request does not seem to work. + * So we need to retry ARP request anyway. + * We want to shrink the interval until the second ARP request. + */ +#define CONFIG_ARP_TIMEOUT 500UL /* 0.5 msec */ + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_TIME +#define CONFIG_CMD_NAND /* NAND flash suppport */ + +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_MAX_CHIPS 2 +#define CONFIG_SYS_NAND_ONFI_DETECTION + +#define CONFIG_NAND_DENALI_ECC_SIZE 1024 + +#define CONFIG_SYS_NAND_REGS_BASE 0x68100000 +#define CONFIG_SYS_NAND_DATA_BASE 0x68000000 + +#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_DATA_BASE + 0x10) + +#define CONFIG_SYS_NAND_USE_FLASH_BBT +#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 + +/* memtest works on */ +#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x01000000) + +#define CONFIG_BOOTDELAY 3 +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ +#define CONFIG_AUTOBOOT_KEYED 1 +#define CONFIG_AUTOBOOT_PROMPT \ + "Press SPACE to abort autoboot in %d seconds\n", bootdelay +#define CONFIG_AUTOBOOT_DELAY_STR "d" +#define CONFIG_AUTOBOOT_STOP_STR " " + +/* + * Network Configuration + */ +#define CONFIG_ETHADDR 00:21:83:24:00:00 +#define CONFIG_SERVERIP 192.168.11.1 +#define CONFIG_IPADDR 192.168.11.10 +#define CONFIG_GATEWAYIP 192.168.11.1 +#define CONFIG_NETMASK 255.255.255.0 + +#define CONFIG_LOADADDR 0x84000000 +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR +#define CONFIG_BOOTFILE "fit.itb" + +#define CONFIG_CMDLINE_EDITING /* add command line history */ + +#define CONFIG_BOOTCOMMAND "run $bootmode" + +#define CONFIG_ROOTPATH "/nfs/root/path" +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs $bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off;" \ + "tftpboot; bootm;" + +#define CONFIG_BOOTARGS " user_debug=0x1f init=/sbin/init" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "image_offset=0x00080000\0" \ + "image_size=0x00f00000\0" \ + "verify=n\0" \ + "autostart=yes\0" \ + "norboot=run add_default_bootargs;" \ + "bootm $image_offset\0" \ + "nandboot=run add_default_bootargs;" \ + "nand read $loadaddr $image_offset $image_size;" \ + "bootm\0" \ + "add_default_bootargs=setenv bootargs $bootargs" \ + " console=ttyS0,$baudrate\0" \ + +/* FIT support */ +#define CONFIG_FIT +#define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */ + +/* Open Firmware flat tree */ +#define CONFIG_OF_LIBFDT + +#define CONFIG_HAVE_ARM_SECURE + +/* Memory Size & Mapping */ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SDRAM0_BASE + +#if CONFIG_SDRAM0_BASE + CONFIG_SDRAM0_SIZE >= CONFIG_SDRAM1_BASE +/* Thre is no memory hole */ +#define CONFIG_NR_DRAM_BANKS 1 +#define CONFIG_SYS_SDRAM_SIZE (CONFIG_SDRAM0_SIZE + CONFIG_SDRAM1_SIZE) +#else +#define CONFIG_NR_DRAM_BANKS 2 +#define CONFIG_SYS_SDRAM_SIZE (CONFIG_SDRAM0_SIZE) +#endif + +#define CONFIG_SYS_TEXT_BASE 0x84000000 + +#if defined(CONFIG_SPL_BUILD) +#define CONFIG_BOARD_POSTCLK_INIT +#else +#define CONFIG_SKIP_LOWLEVEL_INIT +#endif + +#define CONFIG_SYS_SPL_MALLOC_START (0x0ff00000) +#define CONFIG_SYS_SPL_MALLOC_SIZE (0x00004000) + +#define CONFIG_SYS_INIT_SP_ADDR (0x0ff08000) + +#define CONFIG_SPL_FRAMEWORK +#define CONFIG_SPL_NAND_SUPPORT + +#define CONFIG_SPL_LIBCOMMON_SUPPORT /* for mem_malloc_init */ +#define CONFIG_SPL_LIBGENERIC_SUPPORT + +#define CONFIG_SPL_BOARD_INIT + +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x10000 + +#endif /* __CONFIG_UNIPHIER_COMMON_H__ */ |