summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-04-30Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
* 'master' of /home/wd/git/u-boot/custodians: powerpc/85xx: don't touch MAS7 on e500v1 when relocating CCSR powerpc/85xx: don't display address map size (32-bit vs. 36-bit) during boot cmd_bdinfo: display the address map size (32-bit vs. 36-bit) PowerPC: correct the SATA for p1/p2 rdb-pc platform powerpc/corenet_ds: Slave core in holdoff when boot from SRIO powerpc/corenet_ds: Slave reads ENV from master when boot from SRIO powerpc/corenet_ds: Slave uploads ucode when boot from SRIO powerpc/corenet_ds: Slave module for boot from SRIO powerpc/corenet_ds: Master module for boot from SRIO powerpc/corenet_ds: Document for the boot from SRIO powerpc/corenet_ds: Correct the compilation errors about ENV powerpc/srio: Rewrite the struct ccsr_rio powerpc/85xx:Fix lds for nand boot debug info powerpc/p2041rdb: add env in NAND support powerpc/p2041rdb: add NAND and NAND boot support powerpc/mpc8xxx: Fix CONFIG_DDR_RAW_TIMING for two boards powerpc/85xx:Avoid vector table compilation for nand_spl powerpc/85xx:Fix IVORs addr after vector table relocation powerpc/85xx:Avoid hardcoded vector address for IVORs powerpc/p1023rds: Disable nor flash node and enable nand flash node
2012-04-30Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk
* 'master' of git://git.denx.de/u-boot-mpc85xx: powerpc/85xx: don't touch MAS7 on e500v1 when relocating CCSR powerpc/85xx: don't display address map size (32-bit vs. 36-bit) during boot cmd_bdinfo: display the address map size (32-bit vs. 36-bit) PowerPC: correct the SATA for p1/p2 rdb-pc platform powerpc/corenet_ds: Slave core in holdoff when boot from SRIO powerpc/corenet_ds: Slave reads ENV from master when boot from SRIO powerpc/corenet_ds: Slave uploads ucode when boot from SRIO powerpc/corenet_ds: Slave module for boot from SRIO powerpc/corenet_ds: Master module for boot from SRIO powerpc/corenet_ds: Document for the boot from SRIO powerpc/corenet_ds: Correct the compilation errors about ENV powerpc/srio: Rewrite the struct ccsr_rio powerpc/85xx:Fix lds for nand boot debug info powerpc/p2041rdb: add env in NAND support powerpc/p2041rdb: add NAND and NAND boot support powerpc/mpc8xxx: Fix CONFIG_DDR_RAW_TIMING for two boards powerpc/85xx:Avoid vector table compilation for nand_spl powerpc/85xx:Fix IVORs addr after vector table relocation powerpc/85xx:Avoid hardcoded vector address for IVORs powerpc/p1023rds: Disable nor flash node and enable nand flash node
2012-04-30Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
* 'master' of /home/wd/git/u-boot/custodians: i2c:designware Turn off the ctrl when setting the speed i2c: Add support for designware i2c controller sh: i2c: Add support I2C controller of SH7734
2012-04-30Merge branch 'master' of git://git.denx.de/u-boot-i2cWolfgang Denk
* 'master' of git://git.denx.de/u-boot-i2c: i2c:designware Turn off the ctrl when setting the speed i2c: Add support for designware i2c controller sh: i2c: Add support I2C controller of SH7734
2012-04-30Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
* 'master' of /home/wd/git/u-boot/custodians: Blackfin: bfin_sdh: drop dos part hardcode Blackfin: move gd/bd to bss by default Blackfin: gd_t: relocate volatile markings
2012-04-30Merge branch 'master' of git://git.denx.de/u-boot-blackfinWolfgang Denk
* 'master' of git://git.denx.de/u-boot-blackfin: Blackfin: bfin_sdh: drop dos part hardcode Blackfin: move gd/bd to bss by default Blackfin: gd_t: relocate volatile markings
2012-04-30image/fit: drop inline markings on parser codeMike Frysinger
Putting "inline" on extern funcs makes no sense, so drop them. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-04-30Merge branch 'master' of git://git.denx.de/u-boot-nds32Wolfgang Denk
* 'master' of git://git.denx.de/u-boot-nds32: board/adp-ag102: add configuration of adp-ag102 board/adp-ag102: add board specific files nds32/ag102: add ag102 soc support nds32/ag102: add header support of ag102 soc
2012-04-30patman: Change the location of patman pathVikram Narayanan
Fix the location of patman path in README Signed-off-by: Vikram Narayanan <vikram186@gmail.com> Cc: Simon Glass <sjg@chromium.org>
2012-04-30patman: Fix a typo errorVikram Narayanan
Signed-off-by: Vikram Narayanan <vikram186@gmail.com> Cc: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
2012-04-29GCC47: Fix warning in md5.cMarek Vasut
md5.c: In function ‘MD5Final’: md5.c:156:2: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing] md5.c:157:2: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing] Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-04-29GCC47: Fix warning in cmd_nand.cMarek Vasut
cmd_nand.c: In function ‘arg_off_size’: cmd_nand.c:216:5: warning: ‘maxsize’ may be used uninitialized in this function [-Wmaybe-uninitialized] Signed-off-by: Marek Vasut <marex@denx.de> Cc: Scott Wood <scottwood@freescale.com> Cc: Wolfgang Denk <wd@denx.de>
2012-04-29Merge branch 'marex@denx.de' of git://git.denx.de/u-boot-stagingWolfgang Denk
* 'marex@denx.de' of git://git.denx.de/u-boot-staging: CMD: CONFIG_CMD_SETECPR -> CONFIG_CMD_SETEXPR on omap3_logic CMD: Fix CONFIG_CMD_SAVEBP_WRITE_SIZE -> CONFIG_CMD_SPL_WRITE_SIZE CMD: Fix typo CMD_FSL -> CMD_MFSL in readme HWW1U1A: Fix CMD_SHA1 -> CMD_SHA1SUM CMD: Remove CMD_LOG, it's unused CMD: Fix typo KGBD -> KGDB on debris board CMD: Drop CONFIG_CMD_EMMC, it's not used CMD: Drop CONFIG_CMD_DFL, it's not used CMD: Drop CMD_DCR, it's not used CMD: Drop CMD_CAN, it's not used CMD: Remove CMD_AUTOSCRIPT, it's not used AT91: Drop AT91_SPIMUX command from cmd_all
2012-04-25Prepare v2012.04.01Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-04-25powerpc/85xx: don't touch MAS7 on e500v1 when relocating CCSRTimur Tabi
The CCSR relocation code in start.S writes to MAS7 on all e500 parts, but that register does not exist on e500v1. Signed-off-by: Timur Tabi <timur@freescale.com>
2012-04-25powerpc/85xx: don't display address map size (32-bit vs. 36-bit) during bootTimur Tabi
Most 85xx boards can be built as a 32-bit or a 36-bit. Current code sometimes displays which of these is actually built, but it's inconsistent. This is especially problematic since the "default" build for a given 85xx board can be either one, so if you don't see a message, you can't always know which size is being used. Not only that, but each board includes code that displays the message, so there is duplication. The 'bdinfo' command has been updated to display this information, so we don't need to display it at boot time. The board-specific code is deleted. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-25cmd_bdinfo: display the address map size (32-bit vs. 36-bit)Timur Tabi
Some Freescale SOCs support 32-bit and 36-bit physical addressing, and U-Boot must be built to enable one or the other. Add this information to the bdinfo command. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-25PowerPC: correct the SATA for p1/p2 rdb-pc platformJerry Huang
For p1/p2 rdb-pc platform, use the PCIe-SATA Silicon Image SATA controller. Therefore, the SATA driver will use sata_sil, instead sata_sil3114. Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> CC: Andy Fleming <afleming@gmail.com>
2012-04-25powerpc/corenet_ds: Slave core in holdoff when boot from SRIOLiu Gang
When boot from SRIO, slave's core can be in holdoff after powered on for some specific requirements. Master can release the slave's core at the right time by SRIO interface. Master needs to: 1. Set outbound SRIO windows in order to configure slave's registers for the core's releasing. 2. Check the SRIO port status when release slave core, if no errors, will implement the process of the slave core's releasing. Slave needs to: 1. Set all the cores in holdoff by RCW. 2. Be powered on before master's boot. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
2012-04-25powerpc/corenet_ds: Slave reads ENV from master when boot from SRIOLiu Gang
When boot from SRIO, slave's ENV can be stored in master's memory space, then slave can fetch the ENV through SRIO interface. NOTE: Because the slave can not erase, write master's NOR flash by SRIO interface, so it can not modify the ENV parameters stored in master's NOR flash using "saveenv" or other commands. Master needs to: 1. Put the slave's ENV into it's own memory space. 2. Set an inbound SRIO window covered slave's ENV stored in master's memory space. Slave needs to: 1. Set a specific TLB entry in order to fetch ucode and ENV from master. 2. Set a LAW entry with the TargetID SRIO1 or SRIO2 for ucode and ENV. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
2012-04-25powerpc/corenet_ds: Slave uploads ucode when boot from SRIOLiu Gang
When boot from SRIO, slave's ucode can be stored in master's memory space, then slave can fetch the ucode image through SRIO interface. For the corenet platform, ucode is for Fman. Master needs to: 1. Put the slave's ucode image into it's own memory space. 2. Set an inbound SRIO window covered slave's ucode stored in master's memory space. Slave needs to: 1. Set a specific TLB entry in order to fetch ucode from master. 2. Set a LAW entry with the TargetID SRIO1 or SRIO2 for ucode. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
2012-04-25powerpc/corenet_ds: Slave module for boot from SRIOLiu Gang
For the powerpc processors with SRIO interface, boot location can be configured from SRIO1 or SRIO2 by RCW. The processor booting from SRIO can do without flash for u-boot image. The image can be fetched from another processor's memory space by SRIO link connected between them. The processor boots from SRIO is slave, the processor boots from normal flash memory space and can help slave to boot from its memory space is master. They are different environments and requirements: master: 1. NOR flash for its own u-boot image, ucode and ENV space. 2. Slave's u-boot image in master NOR flash. 3. Normally boot from local NOR flash. 4. Configure SRIO switch system if needed. slave: 1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV. 2. Boot location should be set to SRIO1 or SRIO2 by RCW. 3. RCW should configure the SerDes, SRIO interfaces correctly. 4. Slave must be powered on after master's boot. 5. Must define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE because of no ucode locally. For the slave module, need to finish these processes: 1. Set the boot location to SRIO1 or SRIO2 by RCW. 2. Set a specific TLB entry for the boot process. 3. Set a LAW entry with the TargetID SRIO1 or SRIO2 for the boot. 4. Slave's u-boot image should be generated specifically by make xxxx_SRIOBOOT_SLAVE_config. This will set SYS_TEXT_BASE=0xFFF80000 and other configurations. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
2012-04-25powerpc/corenet_ds: Master module for boot from SRIOLiu Gang
For the powerpc processors with SRIO interface, boot location can be configured from SRIO1 or SRIO2 by RCW. The processor booting from SRIO can do without flash for u-boot image. The image can be fetched from another processor's memory space by SRIO link connected between them. The processor boots from SRIO is slave, the processor boots from normal flash memory space and can help slave to boot from its memory space is master. They are different environments and requirements: master: 1. NOR flash for its own u-boot image, ucode and ENV space. 2. Slave's u-boot image in master NOR flash. 3. Normally boot from local NOR flash. 4. Configure SRIO switch system if needed. slave: 1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV. 2. Boot location should be set to SRIO1 or SRIO2 by RCW. 3. RCW should configure the SerDes, SRIO interfaces correctly. 4. Slave must be powered on after master's boot. For the master module, need to finish these processes: 1. Initialize the SRIO port and address space. 2. Set inbound SRIO windows covered slave's u-boot image stored in master's NOR flash. 3. Master's u-boot image should be generated specifically by make xxxx_SRIOBOOT_MASTER_config 4. Master must boot first, and then slave can be powered on. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
2012-04-25powerpc/corenet_ds: Document for the boot from SRIOLiu Gang
This document describes the implementation of the boot from SRIO, includes the introduction of envionment, an example based on P4080DS platform, an example of the slave's RCW, and the description about how to use this feature. Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
2012-04-25powerpc/corenet_ds: Correct the compilation errors about ENVLiu Gang
When defined CONFIG_ENV_IS_NOWHERE, there will be some compilation errors: ./common/env_nowhere.o: In function `env_relocate_spec': ./common/env_nowhere.c:38: multiple definition of `env_relocate_spec' ./common/env_flash.o: ./common/env_flash.c:326: first defined here ./common/env_nowhere.o: In function `env_get_char_spec': ./common/env_nowhere.c:42: multiple definition of `env_get_char_spec' ./common/env_flash.o:./common/env_flash.c:78: first defined here ./common/env_nowhere.o: In function `env_init': ./common/env_nowhere.c:51: multiple definition of `env_init' ./common/env_flash.o:./common/env_flash.c:237: first defined here make[1]: *** [./common/libcommon.o] Error 1 make[1]: Leaving directory `./common' make: *** [./common/libcommon.o] Error 2 Remove the CONFIG_ENV_IS_IN_FLASH if defined CONFIG_ENV_IS_NOWHERE. Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
2012-04-25powerpc/srio: Rewrite the struct ccsr_rioLiu Gang
Rewrite this struct for the support of two ports and two message units registers. Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
2012-04-25powerpc/85xx:Fix lds for nand boot debug infoPrabhakar Kushwaha
Currently "u-boot", the elf file generated via u-boot-nand.lds does not contain required debug information i.e. .debug_{line, info, abbrev, aranges, ranges} into their respective _global_ sections. The original ld script line arch/powerpc/cpu/mpc85xx/start.o KEEP(*(.bootpg)) is not entirely correct because the start.o file is already processed by the linker,therefore the file wildcard in "KEEP(*(.bootpg))" will not process start.o again for bootpg. So Fix u-boot-nand.lds to generate these debug information. Signed-off-by: Anmol Paralkar <b07584@freescale.com> Signed-off-by: John Russo <John.Russo@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-25powerpc/p2041rdb: add env in NAND supportShaohui Xie
Add env in NAND support when boot from NAND. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-25powerpc/p2041rdb: add NAND and NAND boot supportShaohui Xie
New P2041RDB board will add a NAND chip, so add support for NAND and NAND boot. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-25powerpc/mpc8xxx: Fix CONFIG_DDR_RAW_TIMING for two boardsYork Sun
P1010RDB and p1_pc_rdb_pc has incorrect configuration for CONFIG_DDR_RAW_TIMING. It should be CONFIG_SYS_DDR_RAW_TIMING. Incorrect setting causes DDR failure in case of SPD absent. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-25powerpc/85xx:Avoid vector table compilation for nand_splPrabhakar Kushwaha
NAND SPL code never compile the vector table. So no need to setup interrupt vector table for NAND SPL. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-25powerpc/85xx:Fix IVORs addr after vector table relocationPrabhakar Kushwaha
After relocation of vector table in SDRAM's lower address, IVORs value should be updated with new handler addresses. As vector tables are relocated to 0x100,0x200... 0xf00 address in DDR.IVORs are updated with 0x100, 0x200,....f00 hard-coded values. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-25powerpc/85xx:Avoid hardcoded vector address for IVORsPrabhakar Kushwaha
For e500 and e500v2 architecturees processor IVPR address should be alinged on 64K boundary. in start.S, CONFIG_SYS_MONITOR_BASE is stored blindly in IVPR assuming it to be 64K aligned. It may not be true always. If it is not aligned, IVPR + IVORs may not point to an exception handler. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-25powerpc/p1023rds: Disable nor flash node and enable nand flash nodeChunhe Lan
In the p1023rds, when system boots from nor flash, kernel only accesses nor flash and can not access nand flash with BR0/OR0; when system boots from nand flash, kernel only accesses nand flash and can not access nor flash with BR0/OR0. Default device tree nor and nand node should have the following structure: Example: nor_flash: nor@0,0 { #address-cells = <1>; #size-cells = <1>; compatible = "cfi-flash"; reg = <0x0 0x0 0x02000000>; bank-width = <2>; device-width = <1>; status = "okay"; partition@0 { label = "ramdisk"; reg = <0x00000000 0x01c00000>; }; } nand_flash: nand@1,0 { #address-cells = <1>; #size-cells = <1>; compatible = "fsl,p1023-fcm-nand", "fsl,elbc-fcm-nand"; reg = <0x2 0x0 0x00040000>; status = "disabled"; u-boot-nand@0 { /* This location must not be altered */ /* 1MB for u-boot Bootloader Image */ reg = <0x0 0x00100000>; read-only; }; } When booting from nor flash, the status of nor node is enabled and the status of nand node is disabled in the default dts file, so do not do anything. But, when booting from nand flash, need to do some operations: o Disable the NOR node by setting status = "disabled"; o Enable the NAND node by setting status = "okay"; Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-24i2c:designware Turn off the ctrl when setting the speedArmando Visconti
The designware i2c controller must be turned off before setting the speed in IC_CON register, as stated in the section 6.3.1 of the dw_apb_i2c_db.pdf. Signed-off-by: Michel Sanches <michel.sanches@st.com> Signed-off-by: Armando Visconti <armando.visconti@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
2012-04-24i2c: Add support for designware i2c controllerVipin KUMAR
Earlier, a driver exists in the u-boot source for designware i2c interface. That driver was specific to spear platforms. This patch implements the i2c controller as a generic driver which can be used by multiple platforms The driver files are now renamed to designware_i2c.c and designware_i2c.h and these are moved into drivers/i2c folder for reusability by other platforms Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
2012-04-24sh: i2c: Add support I2C controller of SH7734Nobuhiro Iwamatsu
Renesas SH7734 has two I2C interfaceis. This supports these I2C. V5: - include i2c.h. - Add check of icsr bit polling logic. - Implement i2c_probe. V4: - Remove sh_i2c_dump_reg function. - Use puts() when there's no format. - Chnage check for I2C bus number. - Remove space before the semi-colon. V3: - Fix error for whitespace. V2: - Changed bit control to use the clr|set|clrsetbits_* functions. - Fix wrong comment style. - Add new line before for loop in i2c_read. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Acked-by: Heiko Schocher <hs@denx.de> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-04-23sandbox: Use the new run_command()Simon Glass
Now that run_command() handles both parsers, clean up sandbox to use it. This fixes a build error. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-04-23arm: restore fdt_fixup_ethernet call to do_bootm_linuxStephen Warren
Commit 0a672d4 "arm: Add Prep subcommand support to bootm" re-organized do_bootm_linux for ARM. During the re-organization, the call to fdt_fixup_ethernet() was removed. I assume this was useful, so add it back. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Tom Rini <trini@ti.com>
2012-04-23arm: fix bootm with device treeStephen Warren
Commit 0a672d4 "arm: Add Prep subcommand support to bootm" re-organized do_bootm_linux() for ARM. During the re-organization, the code to pass the device tree to the kernel was removed. Add it back. This restores the ability to boot a kernel using device tree. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Tom Rini <trini@ti.com> Acked-by: Allen Martin <amartin@nvidia.com> Tested-by: Allen Martin <amartin@nvidia.com>
2012-04-23Fix the behaviour of the 'run' commandTimo Ketola
If one command fails, 'run' command should terminate and not execute any remaining variables. Signed-off-by: Timo Ketola <timo@exertus.fi> Tested-by: Wolfgang Denk <wd@denx.de> Tested-by: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
2012-04-22Blackfin: bfin_sdh: drop dos part hardcodeMike Frysinger
No other driver sets up the part type to DOS in their init, and it doesn't seem to be needed as `mmcinfo` and `mmc part` stll work, so drop it. Reported-by: Marek Vasut <marex@denx.de> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-04-22Blackfin: move gd/bd to bss by defaultMike Frysinger
We don't need these setup manually, so let the bss do the rest. On Blackfin systems, we clear the bss before executing any C code that would use these, so this should be fine. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-04-22Blackfin: gd_t: relocate volatile markingsMike Frysinger
This makes Blackfin behave the same as other ports, and fixes many gcc warnings that show up with 4.5+: board.c:40:1: warning: optimization may eliminate reads and/or writes to register variables Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-04-22board/adp-ag102: add configuration of adp-ag102Macpaul Lin
board: Add config file of board adp-ag102 Add adp-ag102 into boards.cfg Add adp-ag102 into MAINTAINERS doc: add README of ag102 Signed-off-by: Macpaul Lin <macpaul@andestech.com>
2012-04-22board/adp-ag102: add board specific filesMacpaul Lin
Add board specific files. Signed-off-by: Macpaul Lin <macpaul@andestech.com>
2012-04-22nds32/ag102: add ag102 soc supportMacpaul Lin
Add lowlevel ag102 soc support. Signed-off-by: Macpaul Lin <macpaul@andestech.com>
2012-04-22nds32/ag102: add header support of ag102 socMacpaul Lin
Add device address offsets header of ag102 soc. Add ag102 into mach-types.h. Add asm-offsets.c for helping convert C headers into asm. Signed-off-by: Macpaul Lin <macpaul@andestech.com>
2012-04-21Prepare v2012.04Wolfgang Denk
Also tiny style cleanup to tools/patman/README Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-04-21net: ll_temac: drop obsolete "NAMESIZE" defineStephan Linz
... after commit "net/miiphy/serial: drop duplicate NAMESIZE define" (sha1:f6add13) was applied. The building of the new LL TEMAC network driver fails with error below: xilinx_ll_temac.c: In function 'xilinx_ll_temac_initialize': xilinx_ll_temac.c:301: error: 'NAMESIZE' undeclared (first use in this function) xilinx_ll_temac.c:301: error: (Each undeclared identifier is reported only once xilinx_ll_temac.c:301: error: for each function it appears in.) Signed-off-by: Stephan Linz <linz@li-pro.net> Acked-by: Mike Frysinger <vapier@gentoo.org>
generated by cgit v0.10.2 at 2024-08-20 22:53:38 (GMT)