| Age | Commit message (Collapse) | Author |
|---|
|
Shrink brcm,bcm6328-mc size to avoid overlapping with other controllers
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
Shrink brcm,bcm6328-mc size to avoid overlapping with other controllers
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
Shrink brcm,bcm6358-mc size to avoid overlapping with other controllers
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
This adds a new firefly-rk3399 board, MIPI support for rk3399 and
rk3288, rk818 pmic support, mkimage improvements for rockchip and a few
other things.
|
|
|
|
Add mipi dsi configuration for evb-rk3288 device tree.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add grf register define for rk3288 mipi dsi
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add mipi dsi configs for rk3399 evb board
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add dts config for mipi display, include vop, mipi controller, panel, backlight
. And Enable rk808 for lcd_3v3 in another patch.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Enable pwm0 for display of rk3399 evb board. The PWM do not have decicated
interrupt number in dts and can not get periph_id by pinctrl framework. So
init them here.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
plat->size here is used to reserve frame buffer space befor relocation.
our mipi panel use 24 bitwidth, and vop require 32bit align. So the frame
buffer size should be at least 1920*1200*32/8.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Because the bitwidth is different for different display mode, so we need
to set them according to demand.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add mipi display mode for rk3399 vop, so that we can use mipi panel
for display.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
It's caused by the difference of clk_set_rate function implement between
rk3288 andd rk3399.
clk_set_rate() of rk3288 return 0 in normal condition.
clk_set_rate() of rk3399 return input parameter in normal condition.
So check clk_set_rate's return value by IS_ERR_VALUE.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
|
|
Add basic driver for mipi display on rockchip soc platform.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Add GRF register declaration for mipi dsi.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Since this driver can be used for rk8xx series pmic,
let's rename rk808 to rk8xx, to make it clear.
Configs parts are done by sed -i "s/RK808/RK8XX/g" `grep RK808 -lr ./`
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
|
|
Add support for the rk818 regulator. The regulator module consists
of 4 DCDCs, 9 LDOs, 1 switch and 1 BOOST converter which is used to
power OTG and HDMI5V.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Using mask is more flexible than bits.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The RK818 chip is a Power Management IC (PMIC) for multimedia and handheld
devices.
For boards use rk818, the input current should be set in the early stage, before
ddr initialization.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
|
|
Both RK808 and RK818 chips are using a similar register map,
so we can reuse them.
I have also add reg prefix to exist registers, to keep them same style.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Set ethernet mac address in late init for Tinker Board,
prevents getting a random mac address each boot.
Read mac address from eeprom, first 6 bytes from m24c08@50.
Same as /etc/init.d/rockchip.sh on Tinker OS.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
To add HDMI support for the RK3399, this commit provides the needed
pinctrl functionality to configure the HDMI I2C pins (used for reading
the screen's EDID).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This allows requests (via the DTS) for PCLK_HDMI_CTRL/PCLK_VIO_GRF,
which are clock gates in the HDMI output path for the RK3399.
As these are enabled by default (i.e. after reset), we don't implement
any logic to actively open/close these clock gates and simply assume
that their reset-default has not been changed.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
With the RK3399 DRAM controller (DMC) driver providing all the
infrastructure, retrieve the DRAM size from the DMC init in the
board-specific code (instead of hard-coding) for the RK3399-Q7 (Puma).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The (non-secure) efuse node in the DTS requests PCLK_EFUSE1024NS.
To allow us to add a efuse-driver (and more importantly, to allow
probes of such a driver to succeed), we need need to accept requests
for PCLK_EFUSE1024NS and return a non-error result.
As PCLK_EFUSE1024NS is enabled by default (i.e. after reset), we don't
implement any logic to manage this clock gate and simply assume that
the reset-default has not been changed.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The file is from evb-rk3399_defconfig with changes:
- use rk3399-firefly dtb
- re-order by make savedefconfig
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add test case for new interface set_invert().
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fix typo in subject and build error in sandbox_pwm_set_invert():
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This is a copy from kernel.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Rockchip pwm need to init polarity, implement pwm_set_invert()
to do it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
The latest kernel PWM drivers enable the polarity settings. When system
run from U-Boot to kerenl, if there are differences in polarity set or
duty cycle, the PMW will re-init:
close -> set polarity and duty cycle -> enable the PWM.
The power supply controled by pwm regulator may have voltage shaking,
which lead to the system not stable.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Firefly-rk3399 is a bord from T-Firefly, you can find detail about
it here:
http://en.t-firefly.com/en/firenow/Firefly_RK3399/
This patch add basic node for the board and make it able to bring
up.
Peripheral/interfaces on board:
- usb hub which connect to ehci controller;
- UART2 debug
- eMMC
- PCIe
- USB 3.0 HOST, type-C port
- sdio, sd-card
- HDMI
- Ethernet
- OPTICAL
- WiFi/BT
- MIPI CSI/DSI
- IR
- EDP/DP
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The kernel dts has update a lot since the first time we commit rk3399.dtsi,
sync with kernel for further development.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
At present dtoc assumes that nodes which are phandles do not themselves
reference other phandle nodes. Unfortunately this is not necessarilly
true. As a result we can currently output C code which does not compile
because a node declaration can be referenced before it is declared.
Adjust the code to explicitly output all phandle nodes needed by node
before the node itself is output.
This fixes building with the latest rk3399-firefly.dts from Linux, which
has reordered the nodes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The code to generate the tables is quite long. Move the node-output code
into its own function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
|
|
The 'clock-freq-min-max' property was deprecated in the upstream
(i.e. Linux) DTS bindings in favor of the 'max-frequency' property.
With the latest RK3399 DTSI does no longer include the deprecated
property and the rockchip_dw_mmc driver requiring it to be present,
the driver doesn't bind to the node in the RK3399 DTSI any longer
(thus breaking access to the SD card on the RK3399-Q7 board).
To fix this, we implement a similar logic as in the Linux driver: if
the deprecated property is present, we issue a warning (if DEBUG is
enabled); if it is missing, we require 'max-frequency' to be set and
use it to create a min/max value-pair.
See https://github.com/torvalds/linux/commit/b023030f10573de738bbe8df63d43acab64c9f7b
for the deprecation/matching change in Linux.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
The clocking of the designware MMC controller in the upstream
(i.e. Linux) RK3399 has changed/does not match what the current DTS in
U-Boot uses: the first clock entry now is HCLK_SDMMC instead of
SCLK_SDMMC.
With the simple clock driver used for the RK3399, this needs a change
in the selector understood by the various case statements in the driver
to ensure that the driver still loads successfully.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
There are 3 regions used by rk3399 ATF:
- bl31 code, located at 0x10000;
- cortex-m0 code and data, located at 0xff8c0000;
- bl31 data, located at 0xff8c1000 ~ 0xff8c4000;
SPL_TEXT_BASE starts from 0xff8c2000, we need to reserve memory
for ATF data, or else there will be memory corrupt after SPL
loads the ATF image.
More detail about cortex-M0 code in ATF:
https://github.com/ARM-software/arm-trusted-firmware/commit/
8382e17c4c6bffd15119dfce1ee4372e3c1a7890
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
GMAC controller need to init the tx io driver strength to 13mA,
just like the description in dts pinctrl node, or else the controller
may only work in 100MHz Mode, and fail to work at 1000MHz mode.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com <mailto:philipp.tomsich@theobroma-systems.com>>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Enable gmac for evb-rk3399.
Change-Id: I85e35667e08e22e38577e63eb0e65731fc9c69b6
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Since our sdram driver is ready, we can use the actual size
instead of hard code.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
enable debug uart for rk3288 and print something to let people know
where we are
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The pwm3 on evb-rk3399 is used for pwm regulator, need to invert
the polarity to make it work correctly.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
With the validation done for DDR3-1600 (i.e. 800 MHz bus clock), we
add the timings (rk3399-sdram-ddr3-1600.dtsi) and change rk3399-puma.dts
to use these by default.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
Drop blank line at end of file:
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
The DDR3-1333 timings for the RK3399-Q7 (Puma) has some unintended
left-over comments in them. This change cleans the file up.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
The imagetool framework checks whether function pointer for the verify,
print and extract actions are available and will will handle their
absence appropriately.
This change removes the unnecessary functions and uses the driver
structure to convey available functionality to imagetool. This is in
fact better than having verify just return 0 (which previously broke
dumpimage, as dumpimage assumed that we had handled the image and did
not continue to probe further).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Dumpimage (it invoked with "-T rkspi" or "-T rksd") would not work due
to check_params failing. These changes ensure that we can both be called
with an empty imagename.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
This change set adds documentation to the header0 initialisation and
improves readability for the calculations of various offsets/lengths.
As the U-Boot SPL stage doesn't use any payload beyond what is covered
by init_size, we no longer add RK_MAX_BOOT_SIZE to init_boot_size.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
