| Age | Commit message (Collapse) | Author |
|---|
|
The memory reference code takes a very long time to 'train' its SDRAM
interface, around half a second. To avoid this delay on every boot we can
store the parameters from the last training sessions to speed up the next.
Add an implementation of this, storing the training data in CMOS RAM and
SPI flash.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Correct the SPI flash compatible string, add an alias and specify the
position of the MRC cache, used to store SDRAM training settings for the
Memory Reference Code.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
All memory to be reserved for use after relocation by adding a new call
to perform this reservation.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
As a temporary measure before the ICH driver moves over to driver model,
add device tree support to the driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
On x86 we use CMOS RAM to read and write some settings. Add basic support
for this, including access to registers 128-255.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
The existing IP checksum function is only accessible to the 'coreboot' cpu.
Drop it in favour of the new code in the network subsystem.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move the checksum code out into its own file so it can be used elsewhere.
Also use a new version which supports a length which is not a multiple of
2 and add a new function to add two checksums.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add this to the enum so that we can use the various fdtdec functions. A
later commit will move this driver to driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
commit a62e84d7b1824a202dd incorrectly changed the tegra pci code to the
new fdtdec pci helpers. To get the device index of the root port, the
"reg" property should be parsed from the dtb (as was previously the
case).
With this patch i can successfully network boot my jetson tk1
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
|
|
Various minor code format issues are fixed in start16.S:
- U-boot -> U-Boot
- 32bit -> 32-bit
- Use TAB instead of SPACE to indent
- Move the indention location of the GDT comment block
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
On some x86 processors (like Intel Quark) the MTRR registers are not
supported. This is reflected by the CPUID (EAX 01H) result EDX[12].
Accessing the MTRR registers on such processors will cause #GP so we
must test the support flag before accessing MTRR MSRs.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
CPUID (EAX 01H) returns MTRR support flag in EDX bit 12. Probe this
flag in x86_cpu_init_f() and save it in global data.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
arch/x86/cpu/mtrr.c has access to the U-Boot global data thus
DECLARE_GLOBAL_DATA_PTR is needed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Scrolling a line at a time is very slow for reasons that I don't understand.
It seems to take about 100ms to copy 4MB of RAM in the frame buffer. To cope
with this, scroll 5 lines each time.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Some machines are very slow to scroll their displays. To cope with this,
support the CONFIG_CONSOLE_SCROLL_LINES option. Setting this to 5 allows
the display to operate at an acceptable speed by scrolling 5 lines at
a time.
This same option is available for LCDs so when these systems are unified
this code can be unified also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
|
|
Add code to the generic pci_rom file to access the VGA ROM in PCI space
when needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Using coreboot-x86_defconfig, the following error occurred prior to this modification:
CC arch/x86/lib/interrupts
arch/x86/lib/interrupts.c: In function ‘do_irqinfo’:
arch/x86/lib/interrupts.c:134:24: error: iteration 16u invokes undefined behavior [-Werror=aggressive-loop-optimizations]
if (irq_handlers[irq].handler != NULL) {
^
arch/x86/lib/interrupts.c:133:2: note: containing loop
for (irq = 0; irq <= CONFIG_SYS_NUM_IRQS; irq++) {
^
cc1: all warnings being treated as errors
scripts/Makefile.build:275: recipe for target 'arch/x86/lib/interrupts.o' failed
make[1]: *** [arch/x86/lib/interrupts.o] Error 1
Makefile:1093: recipe for target 'arch/x86/lib' failed
make: *** [arch/x86/lib] Error 2
Change-Id: I3572a822081b72ab760f1eb99442e1161d3d167e
Signed-off-by: Sebastien Ronsse <sronsse@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Each time U-Boot boots on Intel Crown Bay board, the displayed hard
drive information is wrong. It could be either wrong capacity or just
a 'Capacity: not available' message. After enabling the debug switch,
we can see the scsi inquiry command did not execute successfully.
However, doing a 'scsi scan' in the U-Boot shell does not expose
this issue.
SCSI: Target spinup took 0 ms.
SATA link 1 timeout.
AHCI 0001.0100 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
flags: ncq stag pm led clo only pmp pio slum part ccc apst
scanning bus for devices...
ahci_device_data_io: 0 byte transferred. <--- scsi inquiry fails
ahci_device_data_io: 512 byte transferred.
ahci_device_data_io: 512 byte transferred.
ahci_device_data_io: 512 byte transferred.
Device 0: (0:0) Vendor: ATA Prod.: Rev: ?8
Type: Hard Disk
Capacity: 912968.3 MB = 891.5 GB (1869759264 x 512)
Found 1 device(s).
So uninitialized contents on the stack were passed to dev_print() to
display those wrong information.
The symptom were observed on two hard drives (one is Seagate, the
other one is Western Digital). The fix is to make sure the AHCI
interface is not busy by checking the error and status information
from task file register after enabling the port in ahci_port_start()
before proceeding other operations like scsi_scan().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Now that we have a full VESA driver we may as well use that. We need to
support the VESA layer being set up by early start-up code or by
running a VGA ROM.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add a driver intended to cope with any VESA-compatible x86 graphics
adapter. It will not support ROMs which use OpenFirmware (Forth) since
there is no support for that in U-Boot. This means that MAC OS cards
will not work.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
These are quite common and we may as well press on and not be so picky.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Allow the supported modes to be listed when in debug mode.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
As it turns out this is a normal condition, so suppress the error.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
We shouldn't assume that the VGA ROM can always be loaded at c0000. This
is only true on x86 machines.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This code is too x86-dependent at present. Correct it so that it can run on
big-endian machines.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This stops the debug mode from working properly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
These boards are still non-generic boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
|
|
This board is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Josef Wagner <Wagner@Microsys.de>
|
|
This board is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
These boards are still non-generic boards.
It is a good thing that we can drop board-specific hack code
from drivers/mtd/nand/nand_base.c
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Andrea "llandre" Marson <andrea.marson@dave-tech.it>
|
|
This board is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
This board is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
|
|
These boards are still non-generic boards:
P1011RDB, P1022RDB, P2010RDB, P2020RDB
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
|
|
These boards are still non-generic boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Dave Liu <daveliu@freescale.com>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
|
|
|
|
The CPU info is already logged during boot e.g.
CPU: Allwinner A20 (SUN7I)
so the prompt is just one more thing to change for each new SoC, just makes it
"sunxi#" instead.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The Hyundai A7HD is a 7" 16:9 A10 powered tablet featuring 1G RAM, 8G
nand, 1024x600 IPS screen, a mini hdmi port, mini usb receptacle and a
headphones port for details see: http://linux-sunxi.org/Hyundai_A7HD
Cc: Mark Janssen <maniac@maniac.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
It turns out that there are some panels where the pwm input is not active low,
so make it configurable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
HDMI, SATA, USB and Ethernet appear functional, I've not done extensive tests
of all peripherals though.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Currently we've separate detailed dram settings for all sun7i boards, this
moves them over to using auto dram configuration so that we can get rid of
all the per board dram_foo.c files.
This has been tested on a A20-Olinuxino-Lime, A20-Olinuxino_MICRO, Bananapi,
Bananapro, Cubieboard2, Cubietruck, Mele_M3 and a Linksprite_pcDuino3.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
The qt840a is one of the many tv-boxes using the "i12" A20 pcb, but it
populates only one of the 2 places for a 16 bit dram ic, thus reducing
the buswidth to 16 bits, and the amount of ram to 512M, which is why we
had a separate config for it.
This commit switches the generic i12-tvbox_defconfig over to DRAM
autoconfiguration, so that it will work with the qt840a too, and drops the
qt840a specific config, like we've done with other memory-amount specific
configs before.
Tested on a generic i12-tvbox with 32 bit bus-width / 1G RAM, and on a
qt840a with 16 bit bus-width / 512M RAM.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
The Chuwi V7 is an A10 (sun4i) based tablet with 1G of RAM, 16G of nand flash,
microsd slot, 7" 1024x768 lvds ips panel, mini hdmi out, headphones out,
stereo speakers, front & back camera and usb wifi.
It is clearly marked "CHUWI", "V7" and "Model: CW0825" on the back of the
tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Add support for Hitachi tx18d42vm LVDS LCD panels, these panels have a
lcd controller which needs to be initialized over SPI, once that is
done they work like a regular LVDS panel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
|
|
|
|
|
|
Add support for Hitachi tx18d42vm LVDS LCD panels, these panels have a
lcd controller which needs to be initialized over SPI, once that is
done they work like a regular LVDS panel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
|
|
PH1-sLD3, PH1-LD6b have DDR channel 2.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
Match the suffixes of SG_MEMCONF_* macros with SZ_* macros defined
by <linux/sizes.h> for readability.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
