| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The defconfig/config.h file were merged but were already out of sync
with mainline. This brings them further into line now.
Cc: Richard Hu <richard.hu@technexion.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
|
|
According to the TRM you have to set bits [21:20] to 0b10 for RAW mode, so
(0x10 << 20) is obviously wrong here.
Signed-off-by: Martin Pietryka <martin.pietryka@chello.at>
|
|
The terminal condition in the area where a PCI device is scanned is wrong,
and 1f.7 isn't scanned.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This allows to drop annoying (char *) casts when setting the host
name of struct sdhci_host.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
ABB should be initialized for all required domains voltage domain
for DRA7: IVA, GPU, EVE in addition to the existing MPU domain. If
we do not do this, kernel configuring just the frequency using the
default boot loader configured voltage can fail on many corner lot
units and has been hard to debug. This specifically is a concern with
DRA7 generation of SoCs since other than VDD_MPU, all other domains
are only permitted to setup the voltages to required OPP only at boot.
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
Since we setup the voltage and frequency for the MM domain, we *must*
setup the ABB configuration needed for the domain as well. If we do not
do this, kernel configuring just the frequency using the default boot
loader configured voltage can fail on many corner lot units.
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
ABB TX_DONE mask will vary depending on ABB module. For example,
3630 never had ABB on IVA domain, while OMAP5 does use ABB on MM domain,
DRA7 has it on all domains with the exception of CORE, RTC.
Hence, move the txdone mask definition over to structure describing
voltage domain.
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
This information is already available under vcores->volts.efuse.reg.
There is no reason for duplicating the information since AVS Class 0
definitions are common for OMAP5 and DRA7 and defined with
STD_FUSE_OPP_* macros. This allows a central location of defining
the ABB and voltage definitions especially since they are reused.
This also makes it simpler to prevent mistakes involved when changing
the boot OPP for the device.
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
Remove several hundred lines of content surrounded by:
#if 0 /* Moved to malloc.h */
... moved stuff ...
#endif /* 0 */ /* Moved to malloc.h */
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
The error message "spl: mmc block read error" may come from two
different functions, so we should better annotate the function name
where the error comes from to help debugging.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This patch updates and simplifies the hikey README. The old
instructions were hard to follow, and convoluted.
This patch also updates the link to the mcuimage.bin which was outdated.
Using an outdated mcuimage.bin results in the additional a53 cores
not coming online when the kernel issues PSCI requests to
arm trusted firmware (ATF).
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
The memory node gets automatically generated by U-Boot
in arch_fixup_fdt(), before passing control to the kernel
using U-Boots representation of the dram banks.
However the upstream kernel uses the memory node to carve-out
regions of RAM for various purposes. To make this work without
changing arch_fixup_fdt() which will effect many platforms
we replicate the upstream memory node layout using the dram
banks.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This is a binding which only exists in U-Boot, but is
required to get working serial in U-Boot.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This allows the reset command to reset the board from
u-boot.
=> reset
resetting ...
INFO: BL1: 0xf9810000 - 0xf9818000 [size = 32768]
NOTICE: Booting Trusted Firmware
NOTICE: BL1: v1.1(debug):7fb9b0e
NOTICE: BL1: Built : 17:06:41, Apr 19 2016
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Currently only the serial pl01x driver is using DT,
and the other drivers still use platform data but
as more DT lands in the upstream kernel the aim is
to migrate the other drivers over to DT as well to
have a fully DT configured hikey u-boot.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This patch adds myself as maintainer for the hikey
U-Boot port.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Import the upstream kernel dts into U-Boot. Currently
only serial is supported, but a lot more DT changes are
queued for v4.7.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
get_timer() returns an unsigned 64-bit value, but is currently assigned to
a signed 32-bit variable. Due to sign extension and data truncation, this
causes the timeout loop in spi_flash_cmd_wait_ready() to immediately (and
incorrectly) fire for about 50% of all time values, based on whether bit
31 is set. In sandbox at least, this causes the test to pass or fail based
on system uptime, as opposed to time since the U-Boot binary was started.
Fixes: 4efad20a1751 ("sf: Update status reg check in spi_flash_cmd_wait_ready")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
According to common eMMC partition table for Android boot (see
PARTS_DEFAULT definition in include/configs/dra7xx_evm.h), "bootloader"
partition (where u-boot.img is stored) starts at 256 KiB. Which is equal
to 512 sectors (as 1 MMC sector size is 512 bytes).
This patch fixes CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR constant so that
it points to correct address of "bootloader" partition and SPL is able to
read, parse and run u-boot.img correctly.
This change was originally done as part of patch [1] in omapzoom u-boot.
Without this patch, SPL fails to parse U-Boot header with next error:
mkimage signature not found - ih_magic = 4814325a
While at it, also fix U-Boot partition size, which is 384 KiB (as stated in
include/configs/dra7xx_evm.h).
[1] http://omapzoom.org/?p=repo/u-boot.git;a=commit;h=742b82d0c0aa0ed8096c2225a00e9f350212efa9
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Update the config.h and defconfig files for the commands that 8e3c036
converted over to Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Add the following CMD options to Kconfig:
CMD_BOOTZ
CMD_ASKENV
CMD_GREPENV
CMD_USB_MASS_STORAGE
CMD_FAT
CMD_MII
CMD_CACHE
CMD_DFU
CMD_EXT2
CMD_EXT4
CMD_EXT4_WRITE
CMD_FS_GENERIC
CMD_MMC
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
[trini: Don't make CMD_USB_MASS_STORAGE nor CMD_DFU depend on CMD_USB]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
A number of moveconfig.py runs have left a instances of multiple empty
lines in a row. Correct this to a single empty line.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND. Due to how we have used this historically
we need to take further care here when converting.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Now that CONFIG_USB_MUSB_HOST is part of Kconfig, migrate that over to
the defconfig files.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files. Remove
all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
|
|
|
|
|
|
|
|
|
|
U-Boot typically interprets unprefixed numbers as base 16, and DFU RAM
entity parsing has historically done so. Reverse the change to default
to base 10, so that values in previously working command-lines aren't
mis-parsed, causing RAM corruption, crashes, hangs, etc.
Fixes: 6aeb877afef0 ("drivers: dfu: ram: fix a crash with dfu ram with invalid dfu_alt_info env")
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
[Test HW: AM335x BBB]
|
|
U-Boot crashes when an invalid dfu_alt_info is set and tried
using dfu command. Fixing this as it is handled in dfu-mmc.
=> dfu 0 ram 0
data abort
pc : [<9ff893d6>] lr : [<9ff6edb9>]
reloc pc : [<808323d6>] lr : [<80817db9>]
sp : 9ef36cf0 ip : 00000158 fp : 9ffbc0b8
r10: 9ffbc0b8 r9 : 9ef36ed8 r8 : 00000000
r7 : 00000000 r6 : 9ffbc0c8 r5 : 9ef36cfc r4 : 9ef392c8
r3 : 00000004 r2 : 00000000 r1 : 9ff9a985 r0 : ffffffff
Flags: Nzcv IRQs off FIQs on Mode SVC_32
Resetting CPU ...
resetting ...
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Remaining bytes means bytes that are not yet transferred
and not the bytes that were transferred in the last transfer.
Reported-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Steve Rae <srae@broadcom.com>
[Test HW: bcm28155_ap board]
|
|
Request size can be greater than ep.packet and still end in a
short packet. We need to tackle this case as end of transfer
(if short_not_ok is not set) as indicated in USB 2.0 Specification [1],
else we get stuck up on certain protocols like fastboot.
[1] - USB2.0 Specification, Section 5.3.2 Pipes
Reported-by: Steve Rae <steve.rae@broadcom.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Steve Rae <steve.rae@broadcom.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
Just use ep->maxpacket to get the maxpacket size
and simplify the bulk-out maxpacket alignment.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Steve Rae <srae@broadcom.com>
|
|
In a dual speed configuration we need to check at runtime if
we want to enable the Full-Speed or High-Speed endpoint.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Steve Rae <srae@broadcom.com>
[Test HW: bcm235xx board]
|
|
wMaxPacketSize for IN endpoing in High-Speed must be 512 and not 64.
While fixing that we do some clean ups like
- use cpu_to_le16(decimal_length) instead of hexadecimal length.
- No need to initialize bInterval to 0. Static variables are 0 initialized.
- Move descriptor setting from fastboot_add to to fastboot_bind.
- check for dual speed configuration before setting the high speed descriptors.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Steve Rae <srae@broadcom.com>
Tested-by: Steve Rae <srae@broadcom.com> [Test HW: bcm235xx board]
|
|
After concatenation of "dfu_alt_info" variable from "dfu_alt_boot" and
"dfu_alt_system" it may happen that test and dummy files alt settings
are different than default 0 and 1.
This patch provides the ability to set different values for them.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
---
Changes for v3:
- replace variables declarations with ones read from configuration file
- remove not necessary str() conversion at DFU host command generation
Changes for v2:
- generate "alt_info" automatically
- use file names as alt settings instead of numerical values
- extend in-code documentation
|
|
By default (on almost all systems) the dfu env variable, which defines
available alt settings, is named as "dfu_alt_info".
However on some platforms (i.e. Odroid XU3), the 'dfu_alt_info' is concatenated
from other variables - namely 'dfu_alt_boot' and 'dfu_alt_system' at run time
(when one types 'dfu 0 mmc 0' for first time).
'dfu_alt_boot' describes alt settings which depend on boot medium - for example
boot loader's LBA sectors which are different on eMMC and SD card because of e.g.
MBR/GPT.
'dfu_alt_system' describes board agnostic alt settings - like rootfs, kernel.
On such system we can only append/modify this env variable.
Because of the above, we must have way to modify other than "dfu_ale_info"
variable to perform tests.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
---
Changes for v3:
- None
Changes for v2:
- Rewrite of "alt_info_env_name" variable description
- Use of get() method on python's dictionary to easily obtain default
value
|
|
This patch replaces hardcoded (i.e. 0 and 1) values passed to dfu_{read|write}
with variables.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
---
Changes for v3:
- Replace per module global variables with ones defined inside a function
Changes for v2:
- None
|
|
This patch adds support for the PCI(e) based I2C cores. Which can be
found for example on the Intel Bay Trail SoC. It has 7 I2C controllers
implemented as PCI devices.
This patch also adds the fixed values for the timing registers for
BayTrail which are taken from the Linux designware I2C driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This patch adds DM support to the designware I2C driver. It currently
supports DM and the legacy I2C support. The legacy support should be
removed, once all platforms using it have DM enabled.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
|
|
This patch prepares the designware I2C driver for the DM conversion.
This is mainly done by removing struct i2c_adapter from the functions
that shall be used by the DM driver version as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
|
|
Integrating set_speed() into dw_i2c_set_bus_speed() will make the
conversion to DM easier for this driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
|
|
dw_i2c_enable() is used to dis-/en-able the I2C controller. It makes
sense to add such a function, as the controller is dis-/en-abled
multiple times in the code. Additionally, this function now checks,
if the controller is really dis-/en-abled. This code is copied
from the Linux I2C driver version.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Add the ic_enable_status register to the i2c_regs struct. Additionally
the register offsets are added, to better check, if the offset matches
the register description in the datasheet.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
|
|
On some platforms (e.g. x86), the return value of dev_get_addr() can't
be assigned to a pointer type variable directly. As there might be a
difference between the size of fdt_addr_t and the pointer type. On
x86 for example, "fdt_addr_t" is 64bit but "void *" only 32bit. So
assigning the register base directly in dev_get_addr() results in this
compilation warning:
warning: cast to pointer from integer of different size
This patch introduces the new function dev_get_addr_ptr() that
returns a pointer to the 'reg' address that can be used by drivers
in this case.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Copy the kernel image double-word-wise rather than byte-wise.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
