summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-05-13bfin: Remove spi dma function in bf5xx.Scott Jiang
BF5xx rx dma causes spi flash random read error. Accually spi controller has problems both on tx and rx dma. So remove spi dma support in u-boot. Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com> Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2013-05-13blackfin: Fit u-boot image size into limited nor flash on blackfin.Sonic Zhang
- Disable NAND driver on bf537-stamp. - Make MMC_SPI optional. - Disable LCD driver on bf527-ezkit. - Enlarge BF609 nor flash reserved size from 256k to 512k bytes. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Sonic Zhang <sonic.adi@gmail.com>
2013-05-13blackfin: bf609: add softswitch config commandBob Liu
Add softswitch_output command for bf609-ezkit to enable softswitches. Signed-off-by: Bob Liu <lliubbo@gmail.com> Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2013-05-13blackfin: bf609: implement soft switchSonic Zhang
Set up soft switch pins properly in board init code. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Scott Jiang <scott.jiang@analog.com> Signed-off-by: Bob Liu <lliubbo@gmail.com>
2013-05-13blackfin: Correct early serial mess output in BYPASS boot mode.Sonic Zhang
The early serial should not be configured again in initcode() for BYPASS boot mode and in start() for the other LDR boot modes. In BYPASS boot mode, the start up code is located in Nor flash address other than the DRAM address defined in link script. The code embedded string can't be addressed by its compile time symbol. Calculate it according to the flash offset. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2013-05-13blackfin: Set correct early debug serial baudrate.Sonic Zhang
Calculate the early uart clock from the system clock registers set by the bootrom other than the predefine uboot clock macros. Split the early baudrate setting function and the normal baudrate setting one. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2013-05-13blackfin: run core1 from L1 code sram start address in uboot init code on core 0Sonic Zhang
Define core 1 L1 code sram start address. Add function to enable core 1 for BF609 and BF561. Add config macro to allow customer to run core 1 in uboot init code on core 0. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2013-05-13blackfin: add baudrate to bdinfoBob Liu
Signed-off-by: Bob Liu <lliubbo@gmail.com> Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2013-05-13Blackfin: adjust asm constraints with NMI workaroundMike Frysinger
Newer gcc versions will sometimes use a Preg when "r" constraints, but that'll fail if we use an Ireg in the assignment. So force the code to always use a Dreg. This also fixes early boot crashes for older Blackfin parts when compiled with gcc-4.5. This version ends up selecting the same register for the input and output variables which corrupts the output assignment triggering an exception. P2 = 0xffe02008; /* EVT2 */ R0 = RETS; CALL 1f; RTN; 1: P2 = RETS; <-- BAD RETS = R0; [P2] = P2; <-- BAD Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2013-05-13blackfin: reduce size of u-boot.ldr in bf548-ezkit default config.Bob Liu
Enable VIDEO and NAND supports only when the config options is defined. Signed-off-by: Bob Liu <lliubbo@gmail.com> Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2013-05-13blackfin: limit the max memory dma peripheral transfer size to 4 bytes.Sonic Zhang
Othersize, the bf609 memory dma halts after being enabled. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2013-05-13blackfin: Change the member's type in dma structures.Sonic Zhang
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2013-05-10Move FDT_RAMDISK_OVERHEAD from fdt.h to libfdt_env.hGerald Van Baren
The define should not have been put in fdt.h originally, libfdt_env.h is the proper place for target-specific customizations. Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
2013-05-10Added license header to dtc/libfdt/fdt.h and libfdt_env.hJustin Sobota
This commit adds a license header to fdt.h and libfdt_env.h because the license was omitted. U-Boot note: the u-boot libfdt_env.h header portion was not applied to the u-boot libfdt_env.h because that file was created by Gerald Van Baren (with a license header). - gvb Ref: DTC commit 27cdc1b1 Signed-off-by: Justin Sobota <jsobota@ti.com> Acked-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
2013-05-10Fix typoFrançois Revol
Ref: DTC commit cc11e522 Signed-off-by: François Revol <revol@free.fr>
2013-05-10Export fdt_stringlist_contains()Simon Glass
This function is useful outside libfdt, so export it. Ref: DTC commit b7aa300e Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: David Gibson <david@gibson.dropbear.id.au>
2013-05-10Merge branch 'patman' of git://git.denx.de/u-boot-x86Tom Rini
2013-05-10openrisc: move board linker script(s) to a common in cpu/Stefan Kristiansson
Unifies the openrisc boards linker scripts into a common one. Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
2013-05-10openrisc: specify a memory region for u_boot_listsStefan Kristiansson
Since there are two memory areas defined, vectors and ram, the linker will error when neither of them are specified for a section. Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
2013-05-10fs/ext4: Support device block sizes != 512 bytesEgbert Eich
The 512 byte block size was hard coded in the ext4 file systems. Large harddisks today support bigger block sizes typically 4096 bytes. This patch removes this limitation. Signed-off-by: Egbert Eich <eich@suse.com>
2013-05-10Fix references to the documentation filesAnatolij Gustschin
Many boot image configuration files refer to the appropriate documentation file, but these references contain typos in the directory and file name. Fix them. Also fix reference to doc/README.SPL file. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
2013-05-09patman: Do not hardcode python pathMichal Simek
Patman requires python 2.7.4 to run but it doesn't need to be placed in /usr/bin/python. Use env to ensure that the interpreter used is the first one on environment's $PATH on system with several versions of Python installed. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@ti.com> Acked-by: Simon Glass <sjg@chromium.org>
2013-05-09buildman: Allow conflicting tags to avoid spurious errorsSimon Glass
Conflicting tags can prevent buildman from building two series which exist one after the other in a branch. There is no reason not to allow this sort of workflow with buildman, so ignore conflicting tags in buildman. Change-Id: I2231d04d8684fe0f8fe77f8ea107e5899a3da5e8 Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@ti.com>
2013-05-09env: throw an error when an empty key is usedLucian Cojocar
If the environment contains an entry like "=value" "\0" we should throw an error when parsing the environment. Otherwise, U-Boot will enter in an infinite loop. Signed-off-by: Lucian Cojocar <cojocar@gmail.com>
2013-05-09build: Pull -DBUILD_TAG into separate ifdefMarek Vasut
Currently the base setting for CFLAGS is split in two possibilities, one with -DBUILD_TAG appended at the end and one without, the rest of CFLAGS is the same in both cases. Change this so CFLAGS are always set and the -DBUILD_TAG is appended in separate ifdef. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Tom Rini <trini@ti.com> Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
2013-05-09gpio: Add support for microblaze xilinx GPIOMichal Simek
Microblaze uses gpio which is connected to the system reset. Currently gpio subsystem wasn't used for it. Add gpio driver and change Microblaze reset logic to be done via gpio subsystem. There are various configurations which Microblaze can have that's why gpio_alloc/gpio_alloc_dual(for dual channel) function has been introduced and gpio can be allocated dynamically. Adding several gpios IP is also possible and supported. For listing gpio configuration please use "gpio status" command This patch also remove one compilation warning: microblaze-generic.c: In function 'do_reset': microblaze-generic.c:38:47: warning: operation on '*1073741824u' may be undefined [-Wsequence-point] Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-05-09microblaze: bootm: Add support for loading initrdMichal Simek
fdt_initrd add additional information to DTB about initrd addresses which are later used by kernel. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-05-09microblaze: bootm: Fix coding style issuesMichal Simek
Prepare place for new patch. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-05-08nds32: Use sections header to obtain link symbolsKuan-Yu Kuo
Include this header to get access to link symbols, which are otherwise removed. Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com> Cc: Macpaul Lin <macpaul@gmail.com>
2013-05-07Merge branch 'master' of git://www.denx.de/git/u-boot-mmcTom Rini
2013-05-06mmc: fsl_esdhc: Use calloc()Fabio Estevam
A malloc() followed by memset() can be simply replaced by calloc(). Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-06mmc: sdhci: return error when failed add_sdhci().Jaehoon Chung
If failed the add_host(), it is reasonable that return value of add_sdhci(). Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-06sdhci: Add sdhci support for spear devicesVipin Kumar
Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Acked-by: Stefan Roese <sr@denx.de> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-06davinci, mmc: Added a delay reading ext CSD registerDavide Bonfanti
Without this additional delay, some eMMC don't negotiate properly bus width Tested on: - Toshiba THGBM2G8D8FBAIB - Toshiba THGBM4G4D1HBAR - Micron MTFC4GMVEA (the one giving the problem) - Hynix H26M64002BNR - SanDisk SDIN5E1-32G Signed-off-by: Davide Bonfanti <davide.bonfanti@bticino.it> Acked-by: Tom Rini <trini@ti.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-06mmc: Split device init to decouple OCR-polling delayChe-Liang Chiou
Most of time that MMC driver spends on initializing a device is polling OCR (operation conditions register). To decouple this polling loop, device init is split into two parts: The first part fires the OCR query command, and the second part polls the result. So the caller is now no longer bound to the OCR-polling delay; he may fire the query, go somewhere and then come back later for the result. To use this, call mmc_set_preinit() on any device which needs this. This can save significant amounts of time on boot (e.g. 200ms) by hiding the MMC init time behind other init. Signed-off-by: Che-Liang Chiou <clchiou@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-06usb: common: Use a global definition for 'min3'Vivek Gautam
We can use a common global method for calculating minimum of 3 numbers. Put the same in 'common header' and let 'ehci' use it. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Acked-by: Tom Rini <trini@ti.com>
2013-05-06usb: fix: Fixing Port status and feature number constantsVivek Gautam
Fix the Port status bit constants and Port feature number constants as a part of USB 2.0 and USB 3.0 Hub class. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
2013-05-06usb: hub: Parallelize power-cycling of root-hub portsVivek Gautam
Untill now we power-cycle (aka: disable power on a port and re-enabling again) one port at a time. Delay of 20ms for Port-power to change multiplies with number of ports in this case. So better we parallelize this process: disable power on all ports, wait for port-power to stabilize and then re-enable the power subsequently. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
2013-05-05USB: ohci-at91: make OHCI work on at91sam9g10 SoCBo Shen
The at91sam9g10 need to configure HCK0 to make OHCI work Signed-off-by: Bo Shen <voice.shen@atmel.com>
2013-05-05USB: SS: Add support for Super Speed USB interfaceVivek Gautam
This adds usb framework support for super-speed usb, which will further facilitate to add stack support for xHCI. Signed-off-by: Vikas C Sajjan <vikas.sajjan@samsung.com> Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
2013-05-05usb: hub: Fix enumration timeoutVivek Gautam
Patch b6d7852c increases timeout for enumeration, taking worst case to be 10 sec. get_timer() api returns timestamp in milliseconds, which is what we are checking in the do-while() loop in usb_hub_configure() (get_timer(start) < CONFIG_SYS_HZ * 10). This should give us a required check for 10 seconds, and thereby we don't need to add additional mdelay of 100 microseconds in each cycle. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Reviewed-by: Vipin Kumar <vipin.kumar@st.com>
2013-05-05usb: Update device class in usb device's descriptorVivek Gautam
Fetch the device class into usb device's dwcriptors, so that the host controller's driver can use this info to differentiate between HUB and DEVICE. Signed-off-by: Amar <amarendra.xt@samsung.com>
2013-05-05usb: hub: Power-cycle on root-hub portsVivek Gautam
XHCI ports are powered on after a H/W reset, however EHCI ports are not. So disabling and re-enabling power on all ports invariably. Signed-off-by: Amar <amarendra.xt@samsung.com> Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
2013-05-05USB: Some cleanup prior to USB 3.0 interface additionVivek Gautam
Some cleanup in usb framework, nothing much on feature side. Signed-off-by: Vikas C Sajjan <vikas.sajjan@samsung.com> Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
2013-05-05usb: common: Weed out USB_**_PRINTFs from usb frameworkVivek Gautam
USB_PRINTF, USB_HUB_PRINTF, USB_STOR_PRINTF, USB_KBD_PRINTF are nothing but conditional debug prints, depending on DEBUG. So better remove them and use debug() simply. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
2013-05-05usb: Add new command to set USB 2.0 port test modesJulius Werner
This patch adds a new 'usb test' command, that will set a port to a USB 2.0 test mode (see USB 2.0 spec 7.1.20). It supports all five test modes on both downstream hub ports and ordinary device's upstream ports. In addition, it supports EHCI root hub ports. Signed-off-by: Julius Werner <jwerner@chromium.org>
2013-05-05USB: EHCI: Add weak functions to support new chipJim Lin
Add ehci_get_port_speed() and ehci_set_usbmode() weak functions for platform driver to support new chip. Signed-off-by: Jim Lin <jilin@nvidia.com>
2013-05-03P1022DS: Set CONFIG_SPL_MAX_SIZE directlyTom Rini
With the u-boot-with-spl.bin rule calling $(OBJCOPY) with CONFIG_SPL_PAD_TO, and CONFIG_SPL_PAD_TO defaulting to CONFIG_SPL_MAX_SIZE we cannot use math here, so set it to 4096 rather than 4 * 1024. Signed-off-by: Tom Rini <trini@ti.com>
2013-05-02Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini
2013-05-02powerpc/85xx: set USB2 default mode to 'device' for (super)hydra boardsShaohui Xie
The Hydra and Superhydra (P3041DS, P5020DS, and P5040DS) boards have a second USB port that can be configured in either host, peripheral (aka device), or OTG (on-the-go) mode. When configured in host mode, if the port is connected to another USB host, damage to the board can occur. To avoid this, we change the default setting to peripheral mode. Ideally, we'd set it to OTG mode, but currently there is no OTG support for these boards. Setting the hwconfig variable will also update the device tree, and so Linux will configure the port for peripheral mode as well. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Timur Tabi <timur@tabi.org> Signed-off-by: Andy Fleming <afleming@freescale.com>
generated by cgit v0.10.2 at 2024-08-20 13:17:17 (GMT)